Hi All,
I've tried to upgrade the ROM of my QTEK S200.
It got completely stuck!!! I had to remove the battery. Now it stays black. Even a hard-reset does nothing. No bootloader, no white screen, nothing. It's like the device doesn't recognize the battery anymore. Same problem with another battery. When I connect the power supply, the light stays red for 5 seconds and then goes out again. No charging (orange) light.
Does this mean that the device was short-cutted (hardware problem) or can this be fixed with some manipulation?
Anybody an idea how I can fix the hardware (if broken) myself? Can't be to difficult if it just blew a fuse ;-)
Thanks
If the accu not charge, I think he is dead. You need a new one. For flashing new rom, you need a good acco over 50 %. Than you go to bootloader modus and flash a WM5 Rom WM5Rom.
coolb4all said:
Hi All,
I've tried to upgrade the ROM of my QTEK S200.
It got completely stuck!!! I had to remove the battery. Now it stays black. Even a hard-reset does nothing. No bootloader, no white screen, nothing. It's like the device doesn't recognize the battery anymore. Same problem with another battery. When I connect the power supply, the light stays red for 5 seconds and then goes out again. No charging (orange) light.
Does this mean that the device was short-cutted (hardware problem) or can this be fixed with some manipulation?
Anybody an idea how I can fix the hardware (if broken) myself? Can't be to difficult if it just blew a fuse ;-)
Thanks
Click to expand...
Click to collapse
Yep, hes dead alrite, make a good paper weight sorry bro...
not the battery
of course I tried a new battery
same problem
Can you make a downgrade to WM5 ? Ist the battery charged now ?
DC Adapter 4,5 V
I had the same problem.
Remove the battery and connect the pin nr 1 (nearest to the cam) to + and the pin nr 5 to -. I think 3,7 to 5 V is ok. Then bootloader and connect to computer.
Don't blame me if anything goes bad ;-)
how to proceed?
I've tried to do as explained...
I've taken an old charger (5v) and connected the cables (black/white striped to 1 and black to 5). I'm not 100 percent sure about + and -, but normally black is always -, if I'm not mistakin'
What should happen? How should I proceed?
My device does nothing... No light. Power button does nothing, hard reset does nothing.
Does this procedure work with a QTEK S200?
Maybe the charger (old gsm) is too old or broken?
Maybe + is black...
Sooo many options ;-)
Worked on mine S200
Of course You must know if the adapter is working and +/-.
When I connected 1 to + and 5 to - I could operate the mobile as if the battery was mounted and working.
My problem began because the battery isn't charging in bootloader mode.
And I'm still stuck there... Because it's a G4 device flashed with G3 SPL... Anyone got a suggestion how to solve this?
JustBored said:
Of course You must know if the adapter is working and +/-.
When I connected 1 to + and 5 to - I could operate the mobile as if the battery was mounted and working.
My problem began because the battery isn't charging in bootloader mode.
And I'm still stuck there... Because it's a G4 device flashed with G3 SPL... Anyone got a suggestion how to solve this?
Click to expand...
Click to collapse
I Did the same thing '''''HELP"""
What you should do
Keep the device on for 2 hours connect it to the electricity.
Install the original rom with the PDA connected like that to the PC, if it does not enter the Rom update continue trying by doing a hard reset with the stylus and pressing the left com button on the left side of the device, then retry the rom install, if it says unable to connect continue trying, using the procedure i explained before, thats what i did when the same stuff happen to me i was without my device working for a month, now i´m using WM6 with the Diamond Rom, so its possible, to do this you just have to keep trying.
my prophet is block and after try of hard reboot is dont turn on.. its not turn on on any way, no detect charger ether ( no red led ) battery was almost full when its go off..
plz help, can i try 1-5 pins solution?
srbwap said:
my prophet is block and after try of hard reboot is dont turn on.. its not turn on on any way, no detect charger ether ( no red led ) battery was almost full when its go off..
plz help, can i try 1-5 pins solution?
Click to expand...
Click to collapse
My friend. A few people have tried the pin method and one or two have succeeded. IMHO i would not try it, for fear of frying your phone, yourself or starting a fire.
Take out the battery for a good couple of hours. Take out SIm card and SD card. Put battery back in and try to charge for at least 5 hours, even if the light does not show (might just be LED issue).
Then see if you can start in boot loader, u now how to yes? (keep camera button pressed, soft reset with stylus, then let go of camera button after few sconds). What happens?
pins to power
I've tried connecting the extreme small pins to the (big) cables of the charger but nothing happens over here. The screen stays black.
To All,
Any hints on how to connect these cables to the pins, without the fact that they're constantly coming off the pins and constantly touching other pins?
You try and tell me about your experience ;-)
revive prophet revive ;-)
I was just playing with my qtek when I noticed that after connecting and disconnecting it to the AC for 5 times or so (with red light going on and off for a second), it tries to startup, but drops dead after a fraction of a second. Damned ;-) No chance of going into bootloader.
Almost there ;-))
coolb4all said:
I was just playing with my qtek when I noticed that after connecting and disconnecting it to the AC for 5 times or so (with red light going on and off for a second), it tries to startup, but drops dead after a fraction of a second. Damned ;-) No chance of going into bootloader.
Almost there ;-))
Click to expand...
Click to collapse
keep it plugged in for about 5 hours, dont play with it or turn it on lol, give a go unless u have done already and just havent said
Direct Connection to 220v doesn't work
The workaround of connecting the pins directly to the charger doesn't seem to work on a QTEK S200 G4.
Since mine is a G4, I wasn't lucky... I'm left with a cut charger cable.
I'll try to charge it for 5 hours but since no led is going on I don't think this will have any effect.
Listen keep it plug in to the electricity for 12 hours, then try to put it in bootloader mode by pressing the, com button on the left side of the device after you hard reset it, with the stylus after you manage to enter the bootloader mode, you only need to follow the steps described on several posts on the forum.
if nothing works connect the device and try to install the original rom, my device is a g3 so i´m not sure if the g4 works the same way.
Related
hey all,
i have tried to downgrade my qtek s200 with the CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE.exe software i found here.. after everything went quite well, when the phone restarted, the screen started to flash on and off.. and when i dont take the batteries out, the screen, the power led and the bluetooth led turns on and off repeatedly..
any suggestions on what i should do?
thanks..
i have exact the same proplem now
i have exact the same proplem now
Same Problem
Remove the battery - whait about 3 min. - plug ac power cable without your battery - put the battery - when the orange light on, turn on your device.
back to the life, but not solve the problem.
sorry my english, i´m from brazil. (don´t speak english)
sarpsuerdas said:
hey all,
i have tried to downgrade my qtek s200 with the CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE.exe software i found here.. after everything went quite well, when the phone restarted, the screen started to flash on and off.. and when i dont take the batteries out, the screen, the power led and the bluetooth led turns on and off repeatedly..
any suggestions on what i should do?
thanks..
Click to expand...
Click to collapse
Sounds to me that you tried to flash a Wizard-ROM on a Prophet.
This is simply impossible, so you probably bricked your device.
well its somewhat working i'm on a prophet bootloader ipl 2.09 spl 2.20 right now and i'm using a crossbow rom from the wizard section right now... (camera is not working).
what you could try is cut the charger wire open and attach the inner cable to the first battery pin (physical top) and the outer wire to the fifth pin. then go into bootloader, connect to computer and flash a prophet rom which has spl and ipl included.
dou you have a g3 or g4 device? on which spl/ipl are you right now...
I did the same thing with my s200.
I remove cable and battery, insert adapter cable and then battery until I get a steady amber light (usually takes 2-4 attempts).
When it boots up I quickly replace the adapter cable with the computer cable and Active Sync works.
I would like to reflash it but I can't since my battery is reporting 0% always, even when the battery is fully charged and it's not charging either. (And I can't get into the bootloader either.)
@crOssy: are the batteries different between models? and if so, would your proposed wiring actually work? have it been tested?
Hi all, I need a little help!
Got an Orange SPV M600 - Had old rom - Upgraded to WM6 rom, all worked sweet. Tried to do a CID unlock using awizard1.2 (Left it alone for a while to do its thing) not i cant get it to turn on at all.
1. Tried a master reset - Camera + Comm Mgr + soft reset (Nothing happens)
1a. Tried Camera and softreset too (nothing happens)
2. Tried Charger short to Pins 1 and 5 (nothing happens)
3. Left battery out for 24 hours (Nothing happens)
I have bricked the device! - Is there anything else I can do except go back to orange or htc service dept and ask for help?
Cheers
Hi!! Where did you get the WM6 rom for SPV M600??
Have been looking for ages!!
killian1407
Go to Tonydeli7 thread on upgrading. Go & flash the WM5 NVID version.
Then download your choice of WM6 version from PDAviet.
Dogs Nads mate. I unlocked my £75 eBay SPV M600 (courtesy of the gang) to use on Vodafone company chip, but the stock crappy grey background on the Orange WM5 fone dialer skin is total toilet..Just cant been seen on windscreen mount in my car. Follow the rules written by the guys (actually went a lot quicker than the 15-20 ,mins)..JOB DONE!
..PROPR BO I TELL THEE!!
M600 Still dead!
I have been waiting an age for someone to reply to my post with a solution but non has turned up.
Still have the problem but now its gotten a whole lot worse.
1. Plugging the M600 into the wall charger I get a red led that stays on for about 10 seconds, then goes out and nothing else happens - If I then unplug the phone and plug it back in again there is no red led. If I leave the phone unplugged over night then plug it into the power I get a red led for 10 secs then nothing.
2. Have chopped a charged and tried the pin 1 white and pin 5 other cables method but I still get no response. I have tried all combos of stylus and buttons but I just cant make this device respond.
I have just about given up hope of ever resurrecting this thing!
Is there anything else I could try?
Thanks.
i head a situation like this but mine is flashing in about 1 flash pro second, leds on top and screan just flash , no usb connection, no start, nothing.. no boot loader.. :-(
dont know what to doo
laser-interceptor said:
i head a situation like this but mine is flashing in about 1 flash pro second, leds on top and screan just flash , no usb connection, no start, nothing.. no boot loader.. :-(
dont know what to doo
Click to expand...
Click to collapse
As you started a new thread, I posted my reply overthere.
lot of people with same problem.
hi, lot of people (and me ) got the same problem after flashing on wm6.
Look on the g4 topic under "prophet upgrading", i think you've got the same problem like me and other.
After opening my phone, i think this is a capa out :/
dvdfilmbuff said:
1. Plugging the M600 into the wall charger I get a red led that stays on for about 10 seconds, then goes out and nothing else happens - If I then unplug the phone and plug it back in again there is no red led. If I leave the phone unplugged over night then plug it into the power I get a red led for 10 secs then nothing.
Click to expand...
Click to collapse
i quest that this 10sec its charge internal batt ... i got same trouble with my prophet
As i said on the title,suddenly i couldn't recharge my Universal anymore,yes i've tried with a brend new official battery as well but everything was in vain.As soon as i plug my charge to my Universal it appear a Red Led and after 3 min or so the led turn off and so the battery.
How can i fix this problem?!
Is there any chance?!
Is it really dead like that?!
Please HHHHHHHEEEEEEEEELLLLLLLPPPPPPPPPPPPPPPPPPP!!!!!!!!!!!!!!!!
If the battery is really brand new, then I guess the connectors might be damaged or the internal power buses might be broken somewhere. Have you dropped your device recently? Or did anything that might explain broken connectors or internal buses?
Nothing happened to my device and never felt down,it just happened suddenly!Now if i won't be able to fix this by myself this means a finger in da a.. cuz my warranty is expired!DAAAAAAAAMN
tetsuokaneda said:
Nothing happened to my device and never felt down,it just happened suddenly!Now if i won't be able to fix this by myself this means a finger in da a.. cuz my warranty is expired!DAAAAAAAAMN
Click to expand...
Click to collapse
It can be a software error. Have you tried hard resetting or installing another ROM?
tnyynt said:
It can be a software error. Have you tried hard resetting or installing another ROM?
Click to expand...
Click to collapse
That's the point!!!
I was trying to update to WM6 but something went wrong and stucked in boot load screen!Then my battery died but when i've tried to charged again i had that problem!!!
tetsuokaneda said:
That's the point!!!
I was trying to update to WM6 but something went wrong and stucked in boot load screen!Then my battery died but when i've tried to charged again i had that problem!!!
Click to expand...
Click to collapse
Your battery is fine, unfortunately your device broke
Unless you have a lot of specialized equipment at home, and the proper qualifications, there's no way in hell you can fix this. I'm sticking with my diagnosis, that either the power routing circuit broke down, or a power bus inside the device.
Really, your best off taking it back to the store, and paying for the repair. Either that, or buying a new phone, and selling this one for spares...
Sorry mate...
mzalan said:
Unless you have a lot of specialized equipment at home, and the proper qualifications, there's no way in hell you can fix this. I'm sticking with my diagnosis, that either the power routing circuit broke down, or a power bus inside the device.
Really, your best off taking it back to the store, and paying for the repair. Either that, or buying a new phone, and selling this one for spares...
Sorry mate...
Click to expand...
Click to collapse
I wanna die!!!I'm completely Fu.. up!!!
What a terrible news!I can't believe it!!!!
If i'll bring my phone to the assistant i'm gonna pay alot of money,at least 200.00 euro!!!!
similar problem
i had the exact same thing happen to my EXEC when i got 2 new batteries for it. One was a standard sized, pretty much the same as the stock one that came with the phone and one was a much larger capacity one that needs an extra cover for the back.
Id been using the device for ages on this huge battery and the charge said 100% constantly. then the device turned itself off and it wouldnt come back on. upon connecting the charger the LED was red, so i thought the battery was dead. I left it on charge over night and when i tried again the next morning it was fine.
this happens everytime with this battery, it just needs a much longer charge than the standard one, and doesnt register properly on the default OS, i havent tried it on my recent upgrade to one of the midget roms.
so try leaving it on charge over night or for a very long time. if all else fails just get a new battery.
That might reset the battery back to life, but I wouldn't exactly count on that. A battery with a broken monitor circuitry is pretty hard to reset.
My last hope,i'm gonna leave charging my phone for a day and then see what happend....I'm desperate
Permanent red light...
I had this problem, I put the phone on charge but forgot to put a battery in - spare phone... It wouldn't work no matter what I did , until I reformatted the DOC by following the steps in the WIKI.
wtpelzer said:
I had this problem, I put the phone on charge but forgot to put a battery in - spare phone... It wouldn't work no matter what I did , until I reformatted the DOC by following the steps in the WIKI.
Click to expand...
Click to collapse
Could u post it please?!
Took a while but here it is...
I did the task 28 55aa command in MTTY which should reformat the DOC alternatively you could reload the bootloader using the link below...
MTTY with "task 28 55aa", "set 14 0", "set 14 9, "set 14 10" and "set 14 20" as described. bootloader screen may be replaced with a blank one, boot it on bootloader mode by "Backlight+Power+Reset"
http://wiki.xda-developers.com/index.php?pagename=Universal_Resets
now upgrade as usual.
If you stuck on the bootloader again after upgrading, try to upgrade the bootloader itself go to http://forum.xda-developers.com/showpost.php?p=1255206&postcount=52
This link gives full instructions :
http://forum.xda-developers.com/showthread.php?t=289325&highlight=task+28+55aa
Hope this helps.
Same Problem, Led Indicator Always red
Hi,
We have the same situation, my jasjar just died in my hands, im reading a txt messages then al of the sudden it hangs, so what i did is reset it but it didnt power on, i removed the battery then after 10mins i put it back but then no power,then i charged it but it didnt power on too and the led indicator is always red, they say that if the indicator is red it means that there is no battery or the battery is missing but i check it thoroughly,the battery is perfectly place on the back of jasjer, i even tried to enter to bootloader but it cant. If anyone knows how can i revive my jasjar pls pls let us know....Thank you so much.
So sad till now there's no single solution.....
wtpelzer said:
I did the task 28 55aa command in MTTY which should reformat the DOC alternatively you could reload the bootloader using the link below...
MTTY with "task 28 55aa", "set 14 0", "set 14 9, "set 14 10" and "set 14 20" as described. bootloader screen may be replaced with a blank one, boot it on bootloader mode by "Backlight+Power+Reset"
http://wiki.xda-developers.com/index.php?pagename=Universal_Resets
now upgrade as usual.
If you stuck on the bootloader again after upgrading, try to upgrade the bootloader itself go to http://forum.xda-developers.com/showpost.php?p=1255206&postcount=52
This link gives full instructions :
http://forum.xda-developers.com/showthread.php?t=289325&highlight=task+28+55aa
Hope this helps.
Click to expand...
Click to collapse
Exactly if my Jasjar is completely dead how can i connect via usb and then use mtty?!
I'm losing my hope to bring it back to live!
have same problem - can do nothing, still waiting
but there is one thing - led flashes once, when i put the charger into the device - but it does nor light, nor flashes - exactly nothing happens
If your device is dead...
Well just to answer the question, if the battery is dead and you can't charge it because of a red LED. I suggest you buy a standalone charger from ebay and charge the battery or get someone else to charge it for you. Then follow the steps as I stated in my previous post...
wtpelzer said:
Well just to answer the question, if the battery is dead and you can't charge it because of a red LED. I suggest you buy a standalone charger from ebay and charge the battery or get someone else to charge it for you. Then follow the steps as I stated in my previous post...
Click to expand...
Click to collapse
The point is that the device is dead and that is why the constant red light. I have a device that is stuck on the splash screen (no solution in sight) and another that fell down and broke. The one that fell down does not power on. If you put a charged battery ang plug in the charger nothing happens, no light comes on, but if you put a discharged battery the red light comes on. I have a third Uni that I accidentally flashed with a BA rom. It is behaving exactly like the broken uni, it does not turn on, does not go into bootloader and the red light comes on when I plug in the charger with a discharged battery in it.
For some things, there's just no cure...
Okay I understand where you're coming from but essentially what you need to do, under normal circumstances, is connect it to your PC, which if the device is working at all the PC will detect it but not connect... In the case of two of your Uni's I don't think this will help - the dropped one and the BA ROM failure. The one with the Red LED, which has stopped working could be a component failure on the board or it could be a Corrupt DOC table. Now to get back to how you'd go about fixing it if it is a corrupt DOC table, when you connect it to the PC and the PC detects it you disable ActiveSync and start MTTY it should give you the option of connecting to the USB port, when it does this if you get a prompt the problem should be fixable because MTTY can "talk" to the device... As for the other's try this method and if it doesn't work sell them for parts or canabalise the one for parts for the other...
I've BRICKED my device
All of a sudden, when the device was connected to the charger and was in standby, I tried to power it up....and it wouldnt turn on. I pulled the charger cable out....the LED was still glowing. I pulled the battery and put it back in.....and that was it. Completely dead....no response
Plugging in the power, switching batteries (fully charged), pressing all buttons, hard reset/emergency mode key combos, punching the reset hole a million times, pulling the batteries in/out with the charger in/out....all sorts of crap tried. Even the power LED doesn't glow when the charger is connected. NO sign of life from the PDA in ANY form. Completely dead = paper weight. Also tried holding the power button for over a minute or two...nothing happens. Also tried using Mirage and pluggin it in....doesn't detect anything.
Now I need some help guys -
1. My i780 is just 2 weeks old. Will my warranty be void if Samsung finds some other rom? If so, how do they process this? Can they fix and I pay for support?
2. If the device doesn't power up, they anyway cant figure what rom's in there...so i should technically qualify for a replacement....am i right?
3. Anyone here have bricked and dealt with samsung service? your experience?
4. Any other ideas on what i could do to unbrick?
Thanks....sucks guys
Shame to hear that
Have you tried to ask in off topic in thread regardnig samsung?
Good luck,
Hey orb!
I guess mine's a total brick here....looks more like a hardware failure. I plug the charger in, the LED doesn't glow....nothing happens no matter what i do. Its just a dead chunk of plastic at the moment. Guess its going back to the service center.
You'll be happy about this though.......i'm back on my trusty universal once again! It still is simply the best device out there! Only gripe is that it runs on just 64megs ram.
Cheers
is that able to flash rom or enter emergency mode ?
i guess may be rom problem ,
i780 propably will like this if you are using the oldest rom ~
dreamtheater39 said:
Hey orb!
I guess mine's a total brick here....looks more like a hardware failure. I plug the charger in, the LED doesn't glow....nothing happens no matter what i do. Its just a dead chunk of plastic at the moment. Guess its going back to the service center.
You'll be happy about this though.......i'm back on my trusty universal once again! It still is simply the best device out there! Only gripe is that it runs on just 64megs ram.
Cheers
Click to expand...
Click to collapse
Oops
Well I´m happy because you return to your Uni but not glad to know that your other device is a piece of junk
Hope to see you around Uni forum!
What ROM is that? WM6.5?
Fix Bricked i780
dreamtheater39 said:
I've BRICKED my device
All of a sudden, when the device was connected to the charger and was in standby, I tried to power it up....and it wouldnt turn on. I pulled the charger cable out....the LED was still glowing. I pulled the battery and put it back in.....and that was it. Completely dead....no response
Plugging in the power, switching batteries (fully charged), pressing all buttons, hard reset/emergency mode key combos, punching the reset hole a million times, pulling the batteries in/out with the charger in/out....all sorts of crap tried. Even the power LED doesn't glow when the charger is connected. NO sign of life from the PDA in ANY form. Completely dead = paper weight. Also tried holding the power button for over a minute or two...nothing happens. Also tried using Mirage and pluggin it in....doesn't detect anything.
Now I need some help guys -
1. My i780 is just 2 weeks old. Will my warranty be void if Samsung finds some other rom? If so, how do they process this? Can they fix and I pay for support?
2. If the device doesn't power up, they anyway cant figure what rom's in there...so i should technically qualify for a replacement....am i right?
3. Anyone here have bricked and dealt with samsung service? your experience?
4. Any other ideas on what i could do to unbrick?
Thanks....sucks guys
Click to expand...
Click to collapse
Read this topic : http://forum.xda-developers.com/showthread.php?t=380723
Regards
dreamtheater39 said:
I've BRICKED my device
All of a sudden, when the device was connected to the charger and was in standby, I tried to power it up....and it wouldnt turn on. I pulled the charger cable out....the LED was still glowing. I pulled the battery and put it back in.....and that was it. Completely dead....no response
Plugging in the power, switching batteries (fully charged), pressing all buttons, hard reset/emergency mode key combos, punching the reset hole a million times, pulling the batteries in/out with the charger in/out....all sorts of crap tried. Even the power LED doesn't glow when the charger is connected. NO sign of life from the PDA in ANY form. Completely dead = paper weight. Also tried holding the power button for over a minute or two...nothing happens. Also tried using Mirage and pluggin it in....doesn't detect anything.
Now I need some help guys -
1. My i780 is just 2 weeks old. Will my warranty be void if Samsung finds some other rom? If so, how do they process this? Can they fix and I pay for support?
2. If the device doesn't power up, they anyway cant figure what rom's in there...so i should technically qualify for a replacement....am i right?
3. Anyone here have bricked and dealt with samsung service? your experience?
4. Any other ideas on what i could do to unbrick?
Thanks....sucks guys
Click to expand...
Click to collapse
hy all!
i have the same problem (
anybody know how to solve this poblem???
My phone is completly dead after i charge the batteries.
i tried to reflash the rom but the mirage IV doesn't detect my phone because i can't power up.
please help guys
Thanks
sorry for my english!
theblacktulip said:
hy all!
i have the same problem (
anybody know how to solve this poblem???
My phone is completly dead after i charge the batteries.
i tried to reflash the rom but the mirage IV doesn't detect my phone because i can't power up.
please help guys
Thanks
sorry for my english!
Click to expand...
Click to collapse
after i try to update my win 6.1 orange rom pbvic2, the mirage got stuck at 13% and after that my phone won`t boot, get stuck at first logo, i try another roms but without success, plssssss help me
Samsung i780 Bricked
my device is not deacting USB in emergency mode it freeze and not powering up ...plz help me
sorry for bad english
Hey,
yesterday night i wanted to check some Whatsapp and grabed my Z3 from the desk.. it was off and didnt react to powerbutton and even not to vol up + power..
When i pluged usb on it, the led was just blinking red.
Now.. i know i have to give it to o2 but.. before.. is it possible somehow to save all data in any way?
loki4321 said:
Hey,
yesterday night i wanted to check some Whatsapp and grabed my Z3 from the desk.. it was off and didnt react to powerbutton and even not to vol up + power..
When i pluged usb on it, the led was just blinking red.
Now.. i know i have to give it to o2 but.. before.. is it possible somehow to save all data in any way?
Click to expand...
Click to collapse
did you try charging it over night?
Yes.. Didn't change anything
Sent from my GT-I9305 using xda app-developers app
Did you charge using pc or wall charger? That can make a huge difference. Try charging overnight with wall charger. Mine usually comes back to life after a few minutes at wall charger. Pc just doesn't charge quick enough
loki4321 said:
Hey,
yesterday night i wanted to check some Whatsapp and grabed my Z3 from the desk.. it was off and didnt react to powerbutton and even not to vol up + power..
When i pluged usb on it, the led was just blinking red.
Now.. i know i have to give it to o2 but.. before.. is it possible somehow to save all data in any way?
Click to expand...
Click to collapse
2 things you can try.
- the reset button at the SD and sim slot. Its a white square far at the left (display facing upwards).
Press and hold it for 10 seconds or so. (Don't press too strong)
But that didn't ever do anything to me, as I once tried to reboot at recovery mode with it.
- wait, wait and wait until the battery is empty (as it's not easily to be taken out). Then connect the stock standard wall charger. Wait for 15min. You can check what happens, but don't touch the phone.
If the led remains red, you can try to power it on, but chances is that it still doesn't work.
If everything else happens, you might be lucky (the led might not be red again).
Good lluck
I'm always curious if a thing worked, leave a message if success or not.
Hey,
after days on the charger i get following:
Phone charges for about 10 seconds.. screen goes on and so and then it stopps, fashes the red led and starts again. i believe the screen takes to much energy at this stage of charging.
i also know what happened.. at this night my phone showed me a looooong time 50% battery.. and it went off.. so the battery drained to much and i dunno how to get it back to work right without giving it back
i can enter fastboot but adb cant conect.. so i dont know how to make a backup other than this..
Sounds like your charger or your cable are faulty (at least, hopefully it's that)
With the wallcharger it should charge quick enough to not go off again.
Definitely try a different charger and cable, if that fails i recommend you claim warranty because then it's probably a hardware failure.
Chargers were all okay, tested them with my i9305, but with my Z3 they didnt work.. just a loop (Charging Loop i will call it yaaay)
I went to o2 today, they took it without charger or else and will repair it.. they gave me a S3 mini for this time (my s3 lte doesnt take any sim cards anymore x.x)
so, hardware failure i believe.. but it was the new 5.02 lollipop.. so be careful if the battery stucks at certain point!