[Q] [q] htc s710 big charging problem please help me !!! - General Questions and Answers

When connecting the phone to the charger the LED light blinks orange
and does not charge the battery (normal the LED should stay lit orange constantly).
I tried another charger ... same problem,I tried even with data cable ... same result .
I changed the ROM (6, 6.1, 6.2, 6.3, 6.5)
Even reset the phone .... nothing seems to work.
Does anyone know what the problem is.
Please help me. Thanks !!!

Related

M600/Prophet dead to the world!

Hi all, I need a little help!
Got an Orange SPV M600 - Had old rom - Upgraded to WM6 rom, all worked sweet. Tried to do a CID unlock using awizard1.2 (Left it alone for a while to do its thing) not i cant get it to turn on at all.
1. Tried a master reset - Camera + Comm Mgr + soft reset (Nothing happens)
1a. Tried Camera and softreset too (nothing happens)
2. Tried Charger short to Pins 1 and 5 (nothing happens)
3. Left battery out for 24 hours (Nothing happens)
I have bricked the device! - Is there anything else I can do except go back to orange or htc service dept and ask for help?
Cheers
Hi!! Where did you get the WM6 rom for SPV M600??
Have been looking for ages!!
killian1407
Go to Tonydeli7 thread on upgrading. Go & flash the WM5 NVID version.
Then download your choice of WM6 version from PDAviet.
Dogs Nads mate. I unlocked my £75 eBay SPV M600 (courtesy of the gang) to use on Vodafone company chip, but the stock crappy grey background on the Orange WM5 fone dialer skin is total toilet..Just cant been seen on windscreen mount in my car. Follow the rules written by the guys (actually went a lot quicker than the 15-20 ,mins)..JOB DONE!
..PROPR BO I TELL THEE!!
M600 Still dead!
I have been waiting an age for someone to reply to my post with a solution but non has turned up.
Still have the problem but now its gotten a whole lot worse.
1. Plugging the M600 into the wall charger I get a red led that stays on for about 10 seconds, then goes out and nothing else happens - If I then unplug the phone and plug it back in again there is no red led. If I leave the phone unplugged over night then plug it into the power I get a red led for 10 secs then nothing.
2. Have chopped a charged and tried the pin 1 white and pin 5 other cables method but I still get no response. I have tried all combos of stylus and buttons but I just cant make this device respond.
I have just about given up hope of ever resurrecting this thing!
Is there anything else I could try?
Thanks.
i head a situation like this but mine is flashing in about 1 flash pro second, leds on top and screan just flash , no usb connection, no start, nothing.. no boot loader.. :-(
dont know what to doo
laser-interceptor said:
i head a situation like this but mine is flashing in about 1 flash pro second, leds on top and screan just flash , no usb connection, no start, nothing.. no boot loader.. :-(
dont know what to doo
Click to expand...
Click to collapse
As you started a new thread, I posted my reply overthere.
lot of people with same problem.
hi, lot of people (and me ) got the same problem after flashing on wm6.
Look on the g4 topic under "prophet upgrading", i think you've got the same problem like me and other.
After opening my phone, i think this is a capa out :/
dvdfilmbuff said:
1. Plugging the M600 into the wall charger I get a red led that stays on for about 10 seconds, then goes out and nothing else happens - If I then unplug the phone and plug it back in again there is no red led. If I leave the phone unplugged over night then plug it into the power I get a red led for 10 secs then nothing.
Click to expand...
Click to collapse
i quest that this 10sec its charge internal batt ... i got same trouble with my prophet

No more bootloader no more nothing, after rom upgrade s200

Hi All,
I've tried to upgrade the ROM of my QTEK S200.
It got completely stuck!!! I had to remove the battery. Now it stays black. Even a hard-reset does nothing. No bootloader, no white screen, nothing. It's like the device doesn't recognize the battery anymore. Same problem with another battery. When I connect the power supply, the light stays red for 5 seconds and then goes out again. No charging (orange) light.
Does this mean that the device was short-cutted (hardware problem) or can this be fixed with some manipulation?
Anybody an idea how I can fix the hardware (if broken) myself? Can't be to difficult if it just blew a fuse ;-)
Thanks
If the accu not charge, I think he is dead. You need a new one. For flashing new rom, you need a good acco over 50 %. Than you go to bootloader modus and flash a WM5 Rom WM5Rom.
coolb4all said:
Hi All,
I've tried to upgrade the ROM of my QTEK S200.
It got completely stuck!!! I had to remove the battery. Now it stays black. Even a hard-reset does nothing. No bootloader, no white screen, nothing. It's like the device doesn't recognize the battery anymore. Same problem with another battery. When I connect the power supply, the light stays red for 5 seconds and then goes out again. No charging (orange) light.
Does this mean that the device was short-cutted (hardware problem) or can this be fixed with some manipulation?
Anybody an idea how I can fix the hardware (if broken) myself? Can't be to difficult if it just blew a fuse ;-)
Thanks
Click to expand...
Click to collapse
Yep, hes dead alrite, make a good paper weight sorry bro...
not the battery
of course I tried a new battery
same problem
Can you make a downgrade to WM5 ? Ist the battery charged now ?
DC Adapter 4,5 V
I had the same problem.
Remove the battery and connect the pin nr 1 (nearest to the cam) to + and the pin nr 5 to -. I think 3,7 to 5 V is ok. Then bootloader and connect to computer.
Don't blame me if anything goes bad ;-)
how to proceed?
I've tried to do as explained...
I've taken an old charger (5v) and connected the cables (black/white striped to 1 and black to 5). I'm not 100 percent sure about + and -, but normally black is always -, if I'm not mistakin'
What should happen? How should I proceed?
My device does nothing... No light. Power button does nothing, hard reset does nothing.
Does this procedure work with a QTEK S200?
Maybe the charger (old gsm) is too old or broken?
Maybe + is black...
Sooo many options ;-)
Worked on mine S200
Of course You must know if the adapter is working and +/-.
When I connected 1 to + and 5 to - I could operate the mobile as if the battery was mounted and working.
My problem began because the battery isn't charging in bootloader mode.
And I'm still stuck there... Because it's a G4 device flashed with G3 SPL... Anyone got a suggestion how to solve this?
JustBored said:
Of course You must know if the adapter is working and +/-.
When I connected 1 to + and 5 to - I could operate the mobile as if the battery was mounted and working.
My problem began because the battery isn't charging in bootloader mode.
And I'm still stuck there... Because it's a G4 device flashed with G3 SPL... Anyone got a suggestion how to solve this?
Click to expand...
Click to collapse
I Did the same thing '''''HELP"""
What you should do
Keep the device on for 2 hours connect it to the electricity.
Install the original rom with the PDA connected like that to the PC, if it does not enter the Rom update continue trying by doing a hard reset with the stylus and pressing the left com button on the left side of the device, then retry the rom install, if it says unable to connect continue trying, using the procedure i explained before, thats what i did when the same stuff happen to me i was without my device working for a month, now i´m using WM6 with the Diamond Rom, so its possible, to do this you just have to keep trying.
my prophet is block and after try of hard reboot is dont turn on.. its not turn on on any way, no detect charger ether ( no red led ) battery was almost full when its go off..
plz help, can i try 1-5 pins solution?
srbwap said:
my prophet is block and after try of hard reboot is dont turn on.. its not turn on on any way, no detect charger ether ( no red led ) battery was almost full when its go off..
plz help, can i try 1-5 pins solution?
Click to expand...
Click to collapse
My friend. A few people have tried the pin method and one or two have succeeded. IMHO i would not try it, for fear of frying your phone, yourself or starting a fire.
Take out the battery for a good couple of hours. Take out SIm card and SD card. Put battery back in and try to charge for at least 5 hours, even if the light does not show (might just be LED issue).
Then see if you can start in boot loader, u now how to yes? (keep camera button pressed, soft reset with stylus, then let go of camera button after few sconds). What happens?
pins to power
I've tried connecting the extreme small pins to the (big) cables of the charger but nothing happens over here. The screen stays black.
To All,
Any hints on how to connect these cables to the pins, without the fact that they're constantly coming off the pins and constantly touching other pins?
You try and tell me about your experience ;-)
revive prophet revive ;-)
I was just playing with my qtek when I noticed that after connecting and disconnecting it to the AC for 5 times or so (with red light going on and off for a second), it tries to startup, but drops dead after a fraction of a second. Damned ;-) No chance of going into bootloader.
Almost there ;-))
coolb4all said:
I was just playing with my qtek when I noticed that after connecting and disconnecting it to the AC for 5 times or so (with red light going on and off for a second), it tries to startup, but drops dead after a fraction of a second. Damned ;-) No chance of going into bootloader.
Almost there ;-))
Click to expand...
Click to collapse
keep it plugged in for about 5 hours, dont play with it or turn it on lol, give a go unless u have done already and just havent said
Direct Connection to 220v doesn't work
The workaround of connecting the pins directly to the charger doesn't seem to work on a QTEK S200 G4.
Since mine is a G4, I wasn't lucky... I'm left with a cut charger cable.
I'll try to charge it for 5 hours but since no led is going on I don't think this will have any effect.
Listen keep it plug in to the electricity for 12 hours, then try to put it in bootloader mode by pressing the, com button on the left side of the device after you hard reset it, with the stylus after you manage to enter the bootloader mode, you only need to follow the steps described on several posts on the forum.
if nothing works connect the device and try to install the original rom, my device is a g3 so i´m not sure if the g4 works the same way.

spv c600 not starting

hello everybody.i have a problem with my spv c600.i bought it few days ago.i had installed some apps on it and next morning my phone was off,althought the battery was full.i made hard reset for three times and the phone started.but this is happening every morning from then.and now i can`t make hard reset.after it asks me to press 0 key shows orange screen and after that turns off.sometimes shows the windows mobile screen but only that and turns off.i don`t understand what is the problem...is it software or hardware problem?
can someone tell me what can i do?i want my phone back...i like it to much
sorry for my bad english
i`m not sure if i posted to the correct section but no one can`t help me?
Try to enter Bootloader (hold camera button and shortly hold Power).
After Bootloader started, you need reflash official ROM.
it enters in bootloader but it stays only 3 seconds and after that turns off.i`m going crazy....i don`t know what to do...is it the battery the problem?but last time when it worked the battery was full
other ideas?
try other battery, or try turn on without battery only power cable plugin.
the same thing without baterry.it stays 3-4 second and after that turns off.which is the problem?
and i don`t understand what is with the led colour.when i put the phone to charger the light is red...i try to make hard reset but the phone turns off and and one cuple of times...the led color becomes orange and green sometimes...
so?what is going on?
can someone help me please?
I think that it is hardware problem. Before am I bought my HTC Tornado, I had Sony Ericsson P900 and after 2 years using suddenly he after power on he stopped at the introductory animation. So I gave it to the service and told me that is it a problem with the motherboard. Your SPV C600 looks that is on it similar.
and what happend with your tornado?
With my Tornado nothing. The hardware problem was in my Sony Ericsson P900. In service told me that is it a problem with the motherboard and that the correction would cost cca 850$ . So I declined correction and bought HTC Tornado, which still works .
oh..thanks anyway.i think i will go to service with my spv...
wow it didn`t started for 2 days and now is working like is new.i don`t understand...where is the problem?
it worked only 2 hours and after that it was dead again
what can i do to fix this problem.it`s ok to change the rom?
fixed.i sold the phone

O2 XDA Mini crashed while upgrading

I was upgrading my O2 mini with WWE 4 ROM which was already upgraded to WWE 1, and suddenly it has crashed and now not starting. I again tried it upgrading in USB mode , now it is not responding , it blinks red and turns off. Please help, I think I have done big mistake by upgrading. WWE 1 was successfully upgraded.
Battery problem?Try charged full and upgrade again
How do I charge the battery it when it is not starting at all ?. It goes off after few minutes.
Waiting for reply. Thank you for the support.
attach _AC_ power source wait 1-2 hours.
Unsuccessful charging
I tried charging ,but it turns off after blinking red within 3 mins. I don't even see USB on screen. Could this be the problem with my battery itself?
Thank You
seems u have nor original AC power source. try with original.
I had the same problem. You may try this,
1. Open the battery and close the back cover.
2. connect USB cable with computer, you will see red led is on (not flashing), it will charge your bachup battery, let it charge for an hour or so.
3. Fix the bty, hope it will work.

[Q] HTC Universal battery not detected

Hello everyone I have a HTC universal and I bought a extended battery.
Everything worked fine until it showed 0 percent ,after that, most of the time it had the red light that means no battery. I switched to original battery and then it started booting , red light , booting again. My questions are:
Is it a hardware or a software problem?
Is there any chance it will work again ? Please help

Categories

Resources