Hey guys ..
i just installeerd Faria WM6 rom on my SPV M3000, and after the reboot (when it was finised) it came back and just went black.
I cant start the dham thing any more. The battery led isnt up also when attached to the powercord.
Any help please!!
this ROMs are designed for the Wizard. I dont know if you device is like the wizard. But it look like a brick... time to spend 30 bucs to buy a wizz
the M3000 IS a wizard... tell me exactly what happened Mr Richz...
Try taking the battery out for a couple minutes, and the putting it back in, and hit the power button and tell me if the LED light comes on ...
My M3000 is CID locked and try to flash it with ShellTool.
I did it yesterday with the Wizard_Love ROM and that worked fine.
But when i was flashing the Faria Rom it was completed, restarted and then nothing happend any more. totally black and wont come back to life..
i tryed it with the wall charger and the USB charger but no results, also removed the battery. But the Battery LED wont come on.
my ipl/spl was 2.18.001
Related
Recently screen of my qtek started to act werid. It was dark like only a half of the pixels flashed. I thought that it is a software problem because up to that moment phone worked just fine so I tried to flash it with a new rom... and I failed... about three times... now my phone is dead and i can't even charge it - no reaction (not even a light). What should I do (burry my best friend?) ? Can anyone help ?
If you cannot charge it you wont be able to flash it again since it is not allowed under 50% of the charge. I advice you to insert a charged battery. Got any friend with a prophet? then reflash it again, doing the whole procedure described in some other posts like:
http://forum.xda-developers.com/showthread.php?t=283245&page=2
you can find some roms there too
Hi all, I need a little help!
Got an Orange SPV M600 - Had old rom - Upgraded to WM6 rom, all worked sweet. Tried to do a CID unlock using awizard1.2 (Left it alone for a while to do its thing) not i cant get it to turn on at all.
1. Tried a master reset - Camera + Comm Mgr + soft reset (Nothing happens)
1a. Tried Camera and softreset too (nothing happens)
2. Tried Charger short to Pins 1 and 5 (nothing happens)
3. Left battery out for 24 hours (Nothing happens)
I have bricked the device! - Is there anything else I can do except go back to orange or htc service dept and ask for help?
Cheers
Hi!! Where did you get the WM6 rom for SPV M600??
Have been looking for ages!!
killian1407
Go to Tonydeli7 thread on upgrading. Go & flash the WM5 NVID version.
Then download your choice of WM6 version from PDAviet.
Dogs Nads mate. I unlocked my £75 eBay SPV M600 (courtesy of the gang) to use on Vodafone company chip, but the stock crappy grey background on the Orange WM5 fone dialer skin is total toilet..Just cant been seen on windscreen mount in my car. Follow the rules written by the guys (actually went a lot quicker than the 15-20 ,mins)..JOB DONE!
..PROPR BO I TELL THEE!!
M600 Still dead!
I have been waiting an age for someone to reply to my post with a solution but non has turned up.
Still have the problem but now its gotten a whole lot worse.
1. Plugging the M600 into the wall charger I get a red led that stays on for about 10 seconds, then goes out and nothing else happens - If I then unplug the phone and plug it back in again there is no red led. If I leave the phone unplugged over night then plug it into the power I get a red led for 10 secs then nothing.
2. Have chopped a charged and tried the pin 1 white and pin 5 other cables method but I still get no response. I have tried all combos of stylus and buttons but I just cant make this device respond.
I have just about given up hope of ever resurrecting this thing!
Is there anything else I could try?
Thanks.
i head a situation like this but mine is flashing in about 1 flash pro second, leds on top and screan just flash , no usb connection, no start, nothing.. no boot loader.. :-(
dont know what to doo
laser-interceptor said:
i head a situation like this but mine is flashing in about 1 flash pro second, leds on top and screan just flash , no usb connection, no start, nothing.. no boot loader.. :-(
dont know what to doo
Click to expand...
Click to collapse
As you started a new thread, I posted my reply overthere.
lot of people with same problem.
hi, lot of people (and me ) got the same problem after flashing on wm6.
Look on the g4 topic under "prophet upgrading", i think you've got the same problem like me and other.
After opening my phone, i think this is a capa out :/
dvdfilmbuff said:
1. Plugging the M600 into the wall charger I get a red led that stays on for about 10 seconds, then goes out and nothing else happens - If I then unplug the phone and plug it back in again there is no red led. If I leave the phone unplugged over night then plug it into the power I get a red led for 10 secs then nothing.
Click to expand...
Click to collapse
i quest that this 10sec its charge internal batt ... i got same trouble with my prophet
Hi!
I have a HTC touch Cruise for about one month now. Starting with last week it started to say that the "main battery is low, device will close" even if the battery is charged (even pluged in). I tried soft reset, battery out, hard reset, nothing. So I decided to reflash it. Now, it gets to the Windows start up screen but after I can hear the sound for turning off device, and the phone turns off for no reason and without a message.
The original language was french, and it was flashed with a english version and olipro spl.
Does anyone has a idea how I can recover my phone ? I have tried to load several roms, none of them worked.
Please help,
Thanks
I have the same 'Main battery is very low' problem on my TC, even when the battery is almost full. I have this issue on Bepe's ROM, ASerg's ROM and also on the official HTC WWE ROM.
It occurs frequently when I soft-reset. When it happens, I can only succesfully start my phone after completely charging it (LED turns green).
I think it must be a hardware problem in my TC. Switching the battery with another TC-battery did not fix it.
Can't you use your phone at all?
Seems like I got the same problem as you guys http://forum.xda-developers.com/showthread.php?t=402765
Any solution yet?
Is it the same on your side, that when you boot up with the Charger plugged in you don't get past the first splash?
hellow to all . i resently installed wm 6.1 on my wizard and eventualy the battery ran out ,so i connected the charger and to my suprise it did not charge so i tryed with another charger and the same result. the thing is it was working perfictly with wm 5.0 and ever since wm 6.1 this happend.to do the install i used awizard to do the ulocking bouth sim and cid then i down graded the IPL and then flashed the PTG rom and it worked perfectly intil the battery situation.when i plug the charger the red light turns on but thats all it does , and it stays that way for days in a row . ive tryed two diffrent battries. can any one help or give any ideas on this situation, thanks in advance.
Most likely you have flashed a G3 IPL and SPL to a G4 device. If it is the case, then sorry that you've got a brick.
the device is a g3 and ipl spl is g3 the olny thing im not sure about is the rom,here is the link from where i got it.http://forum.xda-developers.com/showthread...d=1#post2601705 , can any body tell me if g3 or g4 rom...thanks
please post the full link, its not complete..it gives a 404 Error
There is no G4-only ROM, all custom ROMs now are G3 and G4 capable.
Try to press the reset hole and see if it goes to RUU or not. If it still doesn't power off even though the charge light became green, then there may be a hardware error.
the problem you are experiencing imay be the amp on your charger.
Only an HTC wall charger can revive a flat dead battery.
This charger should say that it is 1Amp (1000ma)
If you use a charger from a motorola/blackeberry/USB charger it will not help you in this case.
Check your amp.
If you do not have an official wall charger, then the only way to revive is to get a new battery
yes i agree with SVI, because i myself faced this probm, when i got a new batt..i had to charge it fully firstt :/ but i went on with the upgrades..and the batt died on me..i used a motorola v3 charger but didnt work..then i went to the shop owner to replace it..and he said that there is a special chargers for these HTC phones, i bought that and its working perfectly now
hey guys thanks for the replies and ive tryed all those solutions ,the wall charger from my htc trinity and the wall charger from the qtek wizard it self and neather do anything.
the only thing that dose work is putting the battery from my trinity and holding it with my hand in place. it turns on but it dosent stay on for long .
it turns off in the following maner the screen starts going white and it stays that way.
i tryed going to bootloader mode and i succeaded but then it turned to the white screen.
changing the subject the IPL is 1.01 and the SPL is 2.18 the rom is a 6.1 ptg rom here is the link:http://forum.xda-developers.com/showthread.php?p=2601705&posted=1#post2601705 this link works i tested it. can anybody tell me if this rom is for g3 or g4 devices, the device with wm5 works fine . or can it be from the IPL and SPL not being the same. can any one tell me why this is happaning iv flashed so many devices and never had this problem . i my self have a qtek magicion, a htc trinity and a qtek prophet. well hope for some help thanks again.
Yes, first step is to ensure that you have a fully charged battery, a new battery is not fully charged so a desktop charger will be helpfull.
The IPL SPL difference is discussed by Dr Puttingham post
http://forum.xda-developers.com/showthread.php?t=285435 step 16
"Watch the rebooting of your PDA, if BOTH IPL and SPL are 1.xx then great. Quite probably your IPL will be 1.xx and your SPL will be 2.xx. Rerun the button 1.05 ROM downgrade a second time and it will become 1.x on both IPL and SPL. You don't need to redo the unlocking."
Hopefully you can maintain bootload (press and hold camera button on start-up) with the new battery
Anouther hopefully usefull post is
http://forum.xda-developers.com/showthread.php?t=276963
Best of luck
ademim said:
hellow to all . i resently installed wm 6.1 on my wizard and eventualy the battery ran out ,so i connected the charger and to my suprise it did not charge so i tryed with another charger and the same result. the thing is it was working perfictly with wm 5.0 and ever since wm 6.1 this happend.to do the install i used awizard to do the ulocking bouth sim and cid then i down graded the IPL and then flashed the PTG rom and it worked perfectly intil the battery situation.when i plug the charger the red light turns on but thats all it does , and it stays that way for days in a row . ive tryed two diffrent battries. can any one help or give any ideas on this situation, thanks in advance.
Click to expand...
Click to collapse
Its sounds like a battery drain partial brick. Under normal situations, the phone will shut down before the battery is completely drained. This is so you don't end up with a completely dead battery. Sometimes, like when the phone is frozen or at the bootloader screen it will run itself completely dead. It sounds to me like you have a completely dead battery. To charge under normal conditions, your battery has to have enough juice to boot the phone one more time. See, when you plug your phone in, if its not on, it will turn on. During boot, there is no connection between charger and battery...the battery has to have enough juice to make it through boot at which point the phone enables the charger. The way I fixed my battery brick was by cutting the end off of a usb cable, striping the wires, and jumping a charge onto the battery.
Please refer to this blog for a description of the steps involved in this process:
http://www.asktheadmin.com/2007/06/htc-wizardcingular-8125-dead-battery_21.html
could be as stupid as the ongoing connection initiated by activesync:
check the schedule settings and change it to manually.
http://forums.wireless.att.com/cng/board/message?board.id=samsung&message.id=62948
Hello guys, first of all i would apologize for my last thread in which i posted a ware, im sorry for that. Anyways i have a problem. I updated my SDA with WM6.5.21234 Standard by Gregory Full. I've been using it for 2 weeks and today i installed the HTC Tornado Radio 02.61.01 from this post (b : WM6 => "the remote party has ended this connection") (i cannot post the link :s) ... and now when i switch on the phone the 1st load screen comes and the mobile is switched of I even tried re-flashing the ROM but no luck.
How far did the flash of the radio package succeed? There is a distribution file that updates the IPL + SPL before the Radio - the flashing stops at several % values but it must continue to 100% and do an automatic reboot.
What do the lines say on the 3-color screen if you go to the bootloader mode?
everything went well, the phone restarted automatically after installation and never turned on =( ... it say's
IPL 1.00
SPL 1.00.0014
Tornado IU
Are you sure about 1.00 for IPL and SPL?
They are quite old - the latest are 2.00 and 2.0..14
I suggest the following sequence:
1.) load the stock ROM from your operator -> check the status for IPL and SPL
2.) update to the latest IPL and SPL and Radio with the combined package from Nitrogens tagline -> check if the Stock ROM still works
3.) load the cooked ROMs as the cooks indicate to do (take care about the format BINFS <size>)
i ddnt get the first step
oooh yeah Thnkx alot man this forum rocks its ok now =)
thnkx for your help
The stock ROM is the one that is on the orginal device as it is "on stock" when you buy it in a shop. As you have Super-CID your device already, you can take any other Tornado "stock" ROM from any vendor - as you like.
The advantage of stock-ROMs is that they are usually complete and everything in there matches to the other. So if such a ROM works - your device does not have problem.
Then you can start to replace pieces one after the other...
got it .... thanks for your help =)
I'm in a little bit of a problem with my i-mate sp5. i upgraded to the wm6.5 and now the orange light by the ear piece keeps flashing as if its charging even when its not plugged it. everytime i restart it i get a different battery level. i brought a new battery and it does the same thing but it doesn't charge. any suggestions? This my i-mate burnt up?
Get back to a stock ROM to see if it is a device problem. If it works ok with the original ROM, then the battery and/or LED driver are screwed in the WM65 ROM. Be sure you load a ROM that has the proper Tornado OEM drivers cooked into it.
Yea i tried that too. Im still not about to charge it fully. the phone seems to get hot too. I thing maybe the phone is burnt out. Is there a place where i can use it as a trade-in or have it refurbished or is it best i jus buy a new one
yea i tried that already. it does the same thing. the phone wont died unless i take it off the charger but it will not charge all the way with either battery and the phone is always hot. with the old battery the charge icon stayed up even without the charger being connected but the charge icon never comes up for the new battery even if the charger is connected. with the new battery it charges a little then it will die very fast because its still tries to charge itself after i disconnect the battery. one time i set the cpu to 228mhz and it overheated and wouldn't come back on until i flashed it again. you think thats th problem? maybe theres a burnt out board or something
The HW controlling the charge is controlled via 2 different methods:
- phone off: the bootloader
- phone on: the windows driver
If the "phone off" gives the same results - try a different battery. The HW inside the phone is hard to break imho.