Related
Hi ! I have a problem with my Kaiser ! The screen is black, the device doesn't turn on ! But when i hold the power key & soft reset hole at the same time,
green light comes on, but the screen stays black ! Is there a way to make my kaiser working ? (Sorry for my english)
Remove battery and then press power button 30 seconds or more.
Worked for me.
Assface said:
Remove battery and then press power button 30 seconds or more.
Worked for me.
Click to expand...
Click to collapse
it doesnt work ! I think there is a problem with spl , because this problem appears after unsuccessful hard spl installing ! I don know how to fix this
IP13 said:
Hi ! I have a problem with my Kaiser ! The screen is blank, the device doesn't turn on ! But when i hold the power key & soft reset hole at the same time,
green light comes on, but the screen stays blank ! Is there a way to make my kaiser working ? (Sorry for my english)
Click to expand...
Click to collapse
Not trying to oversimplify things, but is the device fully charged? Did you have any problems during the flash? Which SPL did you flash? Have you tried a hard reset? Can you get to the bootloader screen to verify the version of SPL installed vs. the version you tried to install?
Just a few questions to help us try to figure out what is going on. Take care!
krouth said:
Not trying to oversimplify things, but is the device fully charged? Did you have any problems during the flash? Which SPL did you flash? Have you tried a hard reset? Can you get to the bootloader screen to verify the version of SPL installed vs. the version you tried to install?
Just a few questions to help us try to figure out what is going on. Take care!
Click to expand...
Click to collapse
The device is fully charged ! The problem was when I tried to install hard spl ...the screen stuck and I made a reset ,after this the phone ca not be turned on and all I see is green light.
I can not get to bootloader screen , when i try to turn on the device the screen i black (blank) but the green light is on
IP13 said:
The device is fully charged ! The problem was when I tried to install hard spl ...the screen stuck and I made a reset ,after this the phone ca not be turned on and all I see is green light.
I can not get to bootloader screen , when i try to turn on the device the screen i black (blank) but the green light is on
Click to expand...
Click to collapse
How are you trying to get to the bootloader screen? Have you fully read through this thread:
http://forum.xda-developers.com/showthread.php?t=533976
Finally, I would recommend downloading the original ROM and installing it. The ROM for the Tilt is here:
http://www.htc.com/us/SupportDownload.aspx?p_id=67&cat=2&dl_id=94
That is straight from HTC's website, and you might look to see if your specific phone is there. You should be able to download it, connect your phone with the USB cable and run the downloaded file from your computer to bring your phone back to it's original state.
If that works, I would then re-read the link above thoroughly and give it another shot. Hope this helps!
krouth said:
How are you trying to get to the bootloader screen? Have you fully read through this thread:
http://forum.xda-developers.com/showthread.php?t=533976
Finally, I would recommend downloading the original ROM and installing it. The ROM for the Tilt is here:
http://www.htc.com/us/SupportDownload.aspx?p_id=67&cat=2&dl_id=94
That is straight from HTC's website, and you might look to see if your specific phone is there. You should be able to download it, connect your phone with the USB cable and run the downloaded file from your computer to bring your phone back to it's original state.
If that works, I would then re-read the link above thoroughly and give it another shot. Hope this helps!
Click to expand...
Click to collapse
Active sync doesnt recognize my Kaiser!
IP13 said:
Active sync doesnt recognize my Kaiser!
Click to expand...
Click to collapse
When you try to run the original HTC ROM installation program (from my previous post) with your phone connected - does it recognize your Kaiser?
krouth said:
When you try to run the original HTC ROM installation program (from my previous post) with your phone connected - does it recognize your Kaiser?
Click to expand...
Click to collapse
no,it doesnt recongnize my kaiser ! when I connect my kaiser via USB Windows says that i have conected a "ZTE USB Modem 6000 CDMA 1x"
IP13 said:
no,it doesnt recongnize my kaiser ! when I connect my kaiser via USB Windows says that i have conected a "ZTE USB Modem 6000 CDMA 1x"
Click to expand...
Click to collapse
I am not asking what Windows thinks you have connected, or whether or not ActiveSync sees the device. What I am asking is: When you run the original HTC ROM installation program:
"RUU_Kaiser_CINGULAR_WWE_3.57.502.2_radio_sign_25.88.40.05_1.65.21.18_Ship.exe"
downloaded from HTC's website, is that program able to see your phone and go through the installation process?
IP13 said:
no,it doesnt recongnize my kaiser ! when I connect my kaiser via USB Windows says that i have conected a "ZTE USB Modem 6000 CDMA 1x"
Click to expand...
Click to collapse
Uninstall Ur Active synce And Install Again .
Then Put Ur Phone In Bootloader Mode I Hope Work Fine
CHK And Post Result
krouth said:
I am not asking what Windows thinks you have connected, or whether or not ActiveSync sees the device. What I am asking is: When you run the original HTC ROM installation program:
"RUU_Kaiser_CINGULAR_WWE_3.57.502.2_radio_sign_25.88.40.05_1.65.21.18_Ship.exe"
downloaded from HTC's website, is that program able to see your phone and go through the installation process?
Click to expand...
Click to collapse
I cant install this rom because it shows me an error : "ERROR [260] CONNECTION
The Update Utillity cannot connect your PDA Phone . Please check that your USB cradle/cable is connected properly between the PC and your PDA phone .
Chech the following :
1.The PDA Phone is connected to the USB cradle/cable.
2.The USB cradle/cable is connected to the PC "
I have allready checked the cable (it works with my other PDA)
delower10 said:
Uninstall Ur Active synce And Install Again .
Then Put Ur Phone In Bootloader Mode I Hope Work Fine
CHK And Post Result
Click to expand...
Click to collapse
I cannot acces bootloader mode , when I am pressing keys to acces bootloader mode the phone screen is still black /blank .
IP13 said:
I cannot acces bootloader mode , when I am pressing keys to acces bootloader mode the phone screen is still black /blank .
Click to expand...
Click to collapse
To access bootloader, you should hold down the camera button (on right side of phone) and the use the stylus to press the reset button (on bottom of phone.) When the phone goes blank, release the camera button.
When you do this, do you still get the blank/black screen?
Also, did you follow EACH step in the following thread:
http://forum.xda-developers.com/showthread.php?t=433835
krouth said:
To access bootloader, you should hold down the camera button (on right side of phone) and the use the stylus to press the reset button (on bottom of phone.) When the phone goes blank, release the camera button.
When you do this, do you still get the blank/black screen?
Also, did you follow EACH step in the following thread:
http://forum.xda-developers.com/showthread.php?t=433835
Click to expand...
Click to collapse
Yes ! I also get the blank screen after following all this steps !
IP13 said:
Yes ! I also get the blank screen after following all this steps !
Click to expand...
Click to collapse
I am not sure.... I have done some searching and ran across this thread:
http://forum.xda-developers.com/showthread.php?t=423486
It has numerous posts about problems people have experienced flashing - maybe you might get some insight there - or at least post your question there where more people might be monitoring the thread. Good luck!
Please take your issue to the right place, better than open a new thread, I sugest
http://forum.xda-developers.com/showthread.php?t=433835
Your situation should be taken by the right guys, not just gessing if this or that might solve the situation, male a post there
Also have a look at the sticky on the top, try to get Dave Shaw help
THx I will try to ask there ....
Fanning the flames.
Okay if you can't access the boot loader then you need to go higher up. I think the chain is Radio Rom, then SPL, then OS. Basically your SPL is gone, that is why your screen is black and you can't get into the boot loader --- cause its gone. So no duh, it can't load the OS. So, your only hope is that your radio rom is working so you can access the phone via cmd interface programmed within it.I really don't know what i'm talking about, but I've bricked my phone too and with some guidance (er explicit instructions in chat) I was (er she was) able to fix it [my situation was far more complicated with a "security locked" device, and a "radio from hell"]. Your key words are frankenkaiser. which you can find here:
http://forum.xda-developers.com/showthread.php?t=394584
Good luck, if you can get into the oemsbl I'm sure your in business. If your feeling nervous bust out the paypal and head to irc.freenode.org #xda-devs {albeit someone will likely help you without the donation but for real your going to hold someone up for an hour or two you should throw them atleast 20$ to save u 200$ }
tyler51773 said:
Okay if you can't access the boot loader then you need to go higher up. I think the chain is Radio Rom, then SPL, then OS. Basically your SPL is gone, that is why your screen is black and you can't get into the boot loader --- cause its gone. So no duh, it can't load the OS. So, your only hope is that your radio rom is working so you can access the phone via cmd interface programmed within it.I really don't know what i'm talking about, but I've bricked my phone too and with some guidance (er explicit instructions in chat) I was (er she was) able to fix it [my situation was far more complicated with a "security locked" device, and a "radio from hell"]. Your key words are frankenkaiser. which you can find here:
http://forum.xda-developers.com/showthread.php?t=394584
Good luck, if you can get into the oemsbl I'm sure your in business. If your feeling nervous bust out the paypal and head to irc.freenode.org #xda-devs {albeit someone will likely help you without the donation but for real your going to hold someone up for an hour or two you should throw them atleast 20$ to save u 200$ }
Click to expand...
Click to collapse
Thx man , appreciate this !!
Well i was using odin and it said it fail,so what do i do? I unplug the usb cable and that's were it all happend,my phone wont go into download mode,recovery mode,wont even turn on,all black screen can someone please help me
ssfirme said:
Well i was using odin and it said it fail,so what do i do? I unplug the usb cable and that's were it all happend,my phone wont go into download mode,recovery mode,wont even turn on,all black screen can someone please help me
Click to expand...
Click to collapse
http://mobiletechvideos.mybigcommerce.com/samsung-galaxy-s-4g-vibrant-4g/
get a usb jig, or purchase the unbrick service.
It's possible that the jig will get you into download mode, and possible it might not.
There is always the unbrick service, though
EDIT: Wow, I didn't notice that before, but mobiletechvideos is now offering unbrickable mod! Very cool! IOW, you should have them unbrickable mod your phone, and never worry about bricking again
hmm i wonder if the jig mode would work
ssfirme said:
hmm i wonder if the jig mode would work
Click to expand...
Click to collapse
hey did you find any work around? even mine got bricked
today i was using my phone normally.. it was working perfect
suddenly the phone hanged up and turned off
i tried to boot it and nothing happened
any suggestions ?!
thank u all
HTC sensation XE
Hboot :1.27
unlocked
kernel: bricked
Rom:ViperS 1.63
hack-zone said:
today i was using my phone normally.. it was working perfect
suddenly the phone hanged up and turned off
i tried to boot it and nothing happened
any suggestions ?!
thank u all
HTC sensation XE
Hboot :1.27
unlocked
kernel: bricked
Rom:ViperS 1.63
Click to expand...
Click to collapse
try to boot into bootloader
then select reboot
see how it goes
rzr86 said:
try to boot into bootloader
then select reboot
see how it goes
Click to expand...
Click to collapse
Can't reach the hboot :/
The phone is not turning on when pressing the power button
and when I plug it in the charge, the charging LED also is not turning on
Is the notification LED blinking? Try charging the battery with a universal charger.
hack-zone said:
Can't reach the hboot :/
The phone is not turning on when pressing the power button
and when I plug it in the charge, the charging LED also is not turning on
Click to expand...
Click to collapse
try charging the device without battery,sim and sdcard for 5-6 hours
then put them back and power on the device
if that fails too then
http://forum.xda-developers.com/showthread.php?t=1522351
rzr86 said:
try charging the device without battery,sim and sdcard for 5-6 hours
then put them back and power on the device
if that fails too then
http://forum.xda-developers.com/showthread.php?t=1522351
Click to expand...
Click to collapse
buddy, I'd got this problem as well once, it won't work. If the LED is not blinking, according to ganeshp, it means a DEFINITE HARD BRICK.
so, I think THE ONLY way to solve it, is to use J-Tag (Or replace the mainboard, a little screwing off).
hope it gets alright.
ashkan-khatar said:
buddy, I'd got this problem as well once, it won't work. If the LED is not blinking, according to ganeshp, it means a DEFINITE HARD BRICK.
so, I think THE ONLY way to solve it, is to use J-Tag (Or replace the mainboard, a little screwing off).
hope it gets alright.
Click to expand...
Click to collapse
yeah i know mate but for some users the unbricking project helped too
if that fails then the last option is jtag
Thank u all for your help guys
hack-zone said:
Thank u all for your help guys
Click to expand...
Click to collapse
did you fix it with j-tag?
Sensation xe beat Not turing on
rzr86 said:
did you fix it with j-tag?
Click to expand...
Click to collapse
Device is showing up in device manager > com port
but no light is blinking and phone is not charging not turning on
BUT pc notifies with sound that usb device is connected and notifies with when unplugged. what to do? :crying:
farazi482 said:
Device is showing up in device manager > com port
but no light is blinking and phone is not charging not turning on
BUT pc notifies with sound that usb device is connected and notifies with when unplugged. what to do? :crying:
Click to expand...
Click to collapse
Hard brick, if you in US contact me, i do jtag service.
tomy1986.nt said:
Hard brick, if you in US contact me, i do jtag service.
Click to expand...
Click to collapse
I am outside US. can u fix it online?
farazi482 said:
Device is showing up in device manager > com port
but no light is blinking and phone is not charging not turning on
BUT pc notifies with sound that usb device is connected and notifies with when unplugged. what to do? :crying:
Click to expand...
Click to collapse
Sorry, Jtag can not do online.
@farazi482
Look here : http://mobiletechvideos.mybigcommerce.com/htc-sensation-4g-jtag-brick-repair/
These people do international business. I think you just need to pay the shipping though...
Sent from my HTC Sensation
deleted
farazi482 said:
Device is showing up in device manager > com port
but no light is blinking and phone is not charging not turning on
BUT pc notifies with sound that usb device is connected and notifies with when unplugged. what to do? :crying:
Click to expand...
Click to collapse
if you see your phone in device manager as QHSUSB_DLOAD or similar then it is bricked please go here to learn how to recover
Sensation Unbricking Project
And to the people who say if your phones LED no blinking it wont unbrick with Dexters unbrick project your wrong. 95% of the unbricked phones used in the unbricking project have NO blinking LED I did it to my old sensation when bricked going S-ON no LED only picked up in windows as stated above and fixed it on my linux machine
Usb detection problemm
KernelDev101 said:
if you see your phone in device manager as QHSUSB_DLOAD or similar then it is bricked please go here to learn how to recover
Sensation Unbricking Project
And to the people who say if your phones LED no blinking it wont unbrick with Dexters unbrick project your wrong. 95% of the unbricked phones used in the unbricking project have NO blinking LED I did it to my old sensation when bricked going S-ON no LED only picked up in windows as stated above and fixed it on my linux machine
Click to expand...
Click to collapse
Installed Ubuntu 12.04.. then it automatically installed 3 packages (dont know about that).. then extracted 32 bit files to Home
Problem: when i write ./brickdetect.sh in terminal it says "Device can't be detected. check connections.." although its correctly plugged in (without battery, sim, sd card)
any idea how to fix this issue?
farazi482 said:
Installed Ubuntu 12.04.. then it automatically installed 3 packages (dont know about that).. then extracted 32 bit files to Home
Problem: when i write ./brickdetect.sh in terminal it says "Device can't be detected. check connections.." although its correctly plugged in (without battery, sim, sd card)
any idea how to fix this issue?
Click to expand...
Click to collapse
plug your phone into linux and open terminal and type dmesg and send output on here
Hello, guys I am noob af so when I was flashing Ubuntu Touch I disconnected my phone and now its don't even show up as USB it just dead no lights no anything but battery is full I checked with multimeter. So I was wondering if its possible to use UART pins to flash kernel so it can boot. Thank You all so much and if it possible just point right direction were i can find more info on serial connections.
mark1320 said:
Hello, guys I am noob af so when I was flashing Ubuntu Touch I disconnected my phone and now its don't even show up as USB it just dead no lights no anything but battery is full I checked with multimeter. So I was wondering if its possible to use UART pins to flash kernel so it can boot. Thank You all so much and if it possible just point right direction were i can find more info on serial connections.
Click to expand...
Click to collapse
There are other ways to start your device from hard-brick state; I once hard-bricked my opo and used ColorOS (Can't remember exactly) with some chinese tool and it then showed fastboot mode from there you can pick it up.
anaskhan27 said:
There are other ways to start your device from hard-brick state; I once hard-bricked my opo and used ColorOS (Can't remember exactly) with some chinese tool and it then showed fastboot mode from there you can pick it up.
Click to expand...
Click to collapse
Yes but it requires to show up as some weird usb in device manager but my don't even show when i plug it in
Charge your phone for 5 to 6 hours, this is what I did then my phone showed up in that device manager. Also follow each step on the unbrick guide on xda
thank you for help
Rex2688 said:
Charge your phone for 5 to 6 hours, this is what I did then my phone showed up in that device manager. Also follow each step on the unbrick guide on xda
Click to expand...
Click to collapse
Its now connecting but stuck in 8974_msimage_mbn loop it just trying to flash 8974_msimage_mbn and resets. Please Help.
Suggestion:
Connect with USB to Linux PC.
Big chance that yr PC sees memory card of OPO.
Copy Rom to the card.
Install with TWRP, if available, or with other similar.
That worked for my OPO brick.
Arvie
Color OS method worked for me. Just install the correct drivers and your good to go.
Hi
Can anybody assist me with Jtagging my rog 5?
I had issues flashing software after a soft brick, now EDL doesn't even show, it's completely hard bricked. I see the software connector present where is it wasn't present in my previous Rog phone 2. However I can't find any resources online to assist me, hence I'm reaching out here. What I'm looking for is a connector, that I can connect on to the software port and do a factory software push
Any help would be greatly appreciated.
Any help on this matter, please?
Aussieboi9 said:
Any help on this matter, please?
Click to expand...
Click to collapse
Buddy i really want to help you with this are you able deassemble the device
Also try to follow these steps hold volume up connect usb and see if edl comes in the computer if not then hold volume down and try if it still didn't work try both up and down volume and connect usb cable
rais.asif786 said:
Buddy i really want to help you with this are you able deassemble the device
Also try to follow these steps hold volume up connect usb and see if edl comes in the computer if not then hold volume down and try if it still didn't work try both up and down volume and connect usb cable
Click to expand...
Click to collapse
I'm glad someone wants to help
Unfortunately I've tried everything physical, I have opened it up and I have found the software point on the main board of the internal. My only problem is, I can't find the right connector/cable so I can run a jtag and Flash the stock firmware directly to the software Point.
if suppose you don't see the edl port in manage, do make cap edl 9008, and use them for 25 seconds, you will see the device connected manually edl.