Hi ! I have a problem with my Kaiser ! The screen is black, the device doesn't turn on ! But when i hold the power key & soft reset hole at the same time,
green light comes on, but the screen stays black ! Is there a way to make my kaiser working ? (Sorry for my english)
Remove battery and then press power button 30 seconds or more.
Worked for me.
Assface said:
Remove battery and then press power button 30 seconds or more.
Worked for me.
Click to expand...
Click to collapse
it doesnt work ! I think there is a problem with spl , because this problem appears after unsuccessful hard spl installing ! I don know how to fix this
IP13 said:
Hi ! I have a problem with my Kaiser ! The screen is blank, the device doesn't turn on ! But when i hold the power key & soft reset hole at the same time,
green light comes on, but the screen stays blank ! Is there a way to make my kaiser working ? (Sorry for my english)
Click to expand...
Click to collapse
Not trying to oversimplify things, but is the device fully charged? Did you have any problems during the flash? Which SPL did you flash? Have you tried a hard reset? Can you get to the bootloader screen to verify the version of SPL installed vs. the version you tried to install?
Just a few questions to help us try to figure out what is going on. Take care!
krouth said:
Not trying to oversimplify things, but is the device fully charged? Did you have any problems during the flash? Which SPL did you flash? Have you tried a hard reset? Can you get to the bootloader screen to verify the version of SPL installed vs. the version you tried to install?
Just a few questions to help us try to figure out what is going on. Take care!
Click to expand...
Click to collapse
The device is fully charged ! The problem was when I tried to install hard spl ...the screen stuck and I made a reset ,after this the phone ca not be turned on and all I see is green light.
I can not get to bootloader screen , when i try to turn on the device the screen i black (blank) but the green light is on
IP13 said:
The device is fully charged ! The problem was when I tried to install hard spl ...the screen stuck and I made a reset ,after this the phone ca not be turned on and all I see is green light.
I can not get to bootloader screen , when i try to turn on the device the screen i black (blank) but the green light is on
Click to expand...
Click to collapse
How are you trying to get to the bootloader screen? Have you fully read through this thread:
http://forum.xda-developers.com/showthread.php?t=533976
Finally, I would recommend downloading the original ROM and installing it. The ROM for the Tilt is here:
http://www.htc.com/us/SupportDownload.aspx?p_id=67&cat=2&dl_id=94
That is straight from HTC's website, and you might look to see if your specific phone is there. You should be able to download it, connect your phone with the USB cable and run the downloaded file from your computer to bring your phone back to it's original state.
If that works, I would then re-read the link above thoroughly and give it another shot. Hope this helps!
krouth said:
How are you trying to get to the bootloader screen? Have you fully read through this thread:
http://forum.xda-developers.com/showthread.php?t=533976
Finally, I would recommend downloading the original ROM and installing it. The ROM for the Tilt is here:
http://www.htc.com/us/SupportDownload.aspx?p_id=67&cat=2&dl_id=94
That is straight from HTC's website, and you might look to see if your specific phone is there. You should be able to download it, connect your phone with the USB cable and run the downloaded file from your computer to bring your phone back to it's original state.
If that works, I would then re-read the link above thoroughly and give it another shot. Hope this helps!
Click to expand...
Click to collapse
Active sync doesnt recognize my Kaiser!
IP13 said:
Active sync doesnt recognize my Kaiser!
Click to expand...
Click to collapse
When you try to run the original HTC ROM installation program (from my previous post) with your phone connected - does it recognize your Kaiser?
krouth said:
When you try to run the original HTC ROM installation program (from my previous post) with your phone connected - does it recognize your Kaiser?
Click to expand...
Click to collapse
no,it doesnt recongnize my kaiser ! when I connect my kaiser via USB Windows says that i have conected a "ZTE USB Modem 6000 CDMA 1x"
IP13 said:
no,it doesnt recongnize my kaiser ! when I connect my kaiser via USB Windows says that i have conected a "ZTE USB Modem 6000 CDMA 1x"
Click to expand...
Click to collapse
I am not asking what Windows thinks you have connected, or whether or not ActiveSync sees the device. What I am asking is: When you run the original HTC ROM installation program:
"RUU_Kaiser_CINGULAR_WWE_3.57.502.2_radio_sign_25.88.40.05_1.65.21.18_Ship.exe"
downloaded from HTC's website, is that program able to see your phone and go through the installation process?
IP13 said:
no,it doesnt recongnize my kaiser ! when I connect my kaiser via USB Windows says that i have conected a "ZTE USB Modem 6000 CDMA 1x"
Click to expand...
Click to collapse
Uninstall Ur Active synce And Install Again .
Then Put Ur Phone In Bootloader Mode I Hope Work Fine
CHK And Post Result
krouth said:
I am not asking what Windows thinks you have connected, or whether or not ActiveSync sees the device. What I am asking is: When you run the original HTC ROM installation program:
"RUU_Kaiser_CINGULAR_WWE_3.57.502.2_radio_sign_25.88.40.05_1.65.21.18_Ship.exe"
downloaded from HTC's website, is that program able to see your phone and go through the installation process?
Click to expand...
Click to collapse
I cant install this rom because it shows me an error : "ERROR [260] CONNECTION
The Update Utillity cannot connect your PDA Phone . Please check that your USB cradle/cable is connected properly between the PC and your PDA phone .
Chech the following :
1.The PDA Phone is connected to the USB cradle/cable.
2.The USB cradle/cable is connected to the PC "
I have allready checked the cable (it works with my other PDA)
delower10 said:
Uninstall Ur Active synce And Install Again .
Then Put Ur Phone In Bootloader Mode I Hope Work Fine
CHK And Post Result
Click to expand...
Click to collapse
I cannot acces bootloader mode , when I am pressing keys to acces bootloader mode the phone screen is still black /blank .
IP13 said:
I cannot acces bootloader mode , when I am pressing keys to acces bootloader mode the phone screen is still black /blank .
Click to expand...
Click to collapse
To access bootloader, you should hold down the camera button (on right side of phone) and the use the stylus to press the reset button (on bottom of phone.) When the phone goes blank, release the camera button.
When you do this, do you still get the blank/black screen?
Also, did you follow EACH step in the following thread:
http://forum.xda-developers.com/showthread.php?t=433835
krouth said:
To access bootloader, you should hold down the camera button (on right side of phone) and the use the stylus to press the reset button (on bottom of phone.) When the phone goes blank, release the camera button.
When you do this, do you still get the blank/black screen?
Also, did you follow EACH step in the following thread:
http://forum.xda-developers.com/showthread.php?t=433835
Click to expand...
Click to collapse
Yes ! I also get the blank screen after following all this steps !
IP13 said:
Yes ! I also get the blank screen after following all this steps !
Click to expand...
Click to collapse
I am not sure.... I have done some searching and ran across this thread:
http://forum.xda-developers.com/showthread.php?t=423486
It has numerous posts about problems people have experienced flashing - maybe you might get some insight there - or at least post your question there where more people might be monitoring the thread. Good luck!
Please take your issue to the right place, better than open a new thread, I sugest
http://forum.xda-developers.com/showthread.php?t=433835
Your situation should be taken by the right guys, not just gessing if this or that might solve the situation, male a post there
Also have a look at the sticky on the top, try to get Dave Shaw help
THx I will try to ask there ....
Fanning the flames.
Okay if you can't access the boot loader then you need to go higher up. I think the chain is Radio Rom, then SPL, then OS. Basically your SPL is gone, that is why your screen is black and you can't get into the boot loader --- cause its gone. So no duh, it can't load the OS. So, your only hope is that your radio rom is working so you can access the phone via cmd interface programmed within it.I really don't know what i'm talking about, but I've bricked my phone too and with some guidance (er explicit instructions in chat) I was (er she was) able to fix it [my situation was far more complicated with a "security locked" device, and a "radio from hell"]. Your key words are frankenkaiser. which you can find here:
http://forum.xda-developers.com/showthread.php?t=394584
Good luck, if you can get into the oemsbl I'm sure your in business. If your feeling nervous bust out the paypal and head to irc.freenode.org #xda-devs {albeit someone will likely help you without the donation but for real your going to hold someone up for an hour or two you should throw them atleast 20$ to save u 200$ }
tyler51773 said:
Okay if you can't access the boot loader then you need to go higher up. I think the chain is Radio Rom, then SPL, then OS. Basically your SPL is gone, that is why your screen is black and you can't get into the boot loader --- cause its gone. So no duh, it can't load the OS. So, your only hope is that your radio rom is working so you can access the phone via cmd interface programmed within it.I really don't know what i'm talking about, but I've bricked my phone too and with some guidance (er explicit instructions in chat) I was (er she was) able to fix it [my situation was far more complicated with a "security locked" device, and a "radio from hell"]. Your key words are frankenkaiser. which you can find here:
http://forum.xda-developers.com/showthread.php?t=394584
Good luck, if you can get into the oemsbl I'm sure your in business. If your feeling nervous bust out the paypal and head to irc.freenode.org #xda-devs {albeit someone will likely help you without the donation but for real your going to hold someone up for an hour or two you should throw them atleast 20$ to save u 200$ }
Click to expand...
Click to collapse
Thx man , appreciate this !!
Related
Can someone upload an old ROM for the prophet? I can't start up my prophet, but I've got it in bootloader. So I nedd a little bit old ROM so I can install on it.
Understand?
Thanks!
Look for the first link here http://forum.xda-developers.com/showpost.php?p=1166927&postcount=2
Are this ROM old ROM?
Not really old but if your phone stuck in bootloader this one is ok
I can't make it, it says that i should connect to Active Sync, and how im I suppose to do that?
Go in bootloader (screen with 3 coulours) by Hold down the camera button and reset the device. (Boot Loader Mode is: Press Camara + Soft Reset, then release soft reset and keep pressing camara button till appear the Boot Loader.)
When you are in bootloader logicaly your PC must detect the Prophet, then run the update
Sorry for my bad English but I'm Franch
Yes i've got it in bootloader, and its stands USB on the PPC screen. But it aint the Active Sync that finds it, it says "Uknoknown Unit" or something when i connect them together..
Active Sync isn't a problem, update work or there is an error message?
In right corner down on the PC sreen it comes up "A unkknown Device connected" or something like that, nothing more is happening..??
It sayd that it can't recognize the unit..
Qtek_S200 said:
It sayd that it can't recognize the unit..
Click to expand...
Click to collapse
In bootloader mode, on connecting via usb ,if u r getting 'USB' written on left down corner of ppc then ur ppc can be flashed via proper RUU and nk.nbf
Be sure that this nk.nbf dont include ipl/spl parts for risk free flashing and for not getting brick device.
thanx
nandlal
Im trying to flash a ROM with that, but it coming up on the screen that "Not connected". It's standing that i nedd to connect with Active SYnc!!
could somebody upload an ipl/spl lower than 2.09 or higher but not 2.09^^
rest doesn't matter language english or german would be good...
Hi
My Uni is dead, dont enter in bootloader mode, dont upgrade, dont do nothing.
Please help me, i dont know what happen.
You have to give us more clue. What were you doing with the Universal before this happened? Were you in the process of upgrading, downloading, etc...?
cktlcmd said:
You have to give us more clue. What were you doing with the Universal before this happened? Were you in the process of upgrading, downloading, etc...?
Click to expand...
Click to collapse
I upgrade with Vista. Dont work nothing.
Solution..
Hey i had the same problem... the Screen will say Serial no. and at the bottom it will say V. 1.01
Just do one thing.... connect yr fone to a desktop with Xp and then try running the upgrader... make sure u have the Sync software with u.....
I know this because the same thing happened with me.. my fone was dead.. till i did this..
try it
danidabest said:
Hey i had the same problem... the Screen will say Serial no. and at the bottom it will say V. 1.01
Just do one thing.... connect yr fone to a desktop with Xp and then try running the upgrader... make sure u have the Sync software with u.....
I know this because the same thing happened with me.. my fone was dead.. till i did this..
try it
Click to expand...
Click to collapse
My problem is the screen dont have nothing, any letters ou numbers.
having constantly the 150 connection error message
hellonasty said:
My problem is the screen dont have nothing, any letters ou numbers.
having constantly the 150 connection error message
Click to expand...
Click to collapse
Have you tried the suggestion at least?
Look for the original ROM of your device and find a WINDOWS XP computer and try to reflash with those 2 as suggested from above.
i want Try Mamaich Method but dont recognize the usb port.
Do you know?
Thanks
hellonasty said:
i want Try Mamaich Method but dont recognize the usb port.
Do you know?
Thanks
Click to expand...
Click to collapse
I don't think it would work. The Mamaich method is for a different problem. Yours clearly is due to Windows Vista incompatibility. I had read a couple of this type of thread in the past and the only solution was already given to you.
do you know where is the original rom?
hellonasty said:
do you know where is the original rom?
Click to expand...
Click to collapse
What type of Universal do you have? TMobile, O2, IMate...etc?
Sorry
I have a qtek9000
Before I tried my 1st upgrade I download the official ROM just in case.
I thought I had it but I can't find it. I have one copy on the PC at work, but I will only return there next Wednesday, so no big help.
I remember see a post were a member informed that he had an ftp with all the ROMS. Maybe some one remember the address. If I get, it i will post it.
Cheers.
Here: http://forum.xda-developers.com/showthread.php?t=296651&highlight=official+qtek+rom
Take a look into this thread at POST #7 by nvatvani
---
cktlcmd said:
Here: ftp://ftp.xda-developers.com/Universal/Uni_AKU2_WWE/QTEK_9000/
---
Click to expand...
Click to collapse
Am I wrong or those are the files that have been deleted because M$ "request"?
ultravox said:
Am I wrong or those are the files that have been deleted because M$ "request"?
Click to expand...
Click to collapse
OOOOPPPPs. that was the wrong dead link. But I corrected it already.
dead xda
i was trying to upgrade rom downloaded from o2 for my xda 2i i have same problem as previous guy i have tried to load from windows xp machine but get connection error 101 my screen is blank apart from usb and v1.01 can anyone help?
sounds to me like it might be as simple as a dead battery.
1. what happens when you try to charge it with the wall charger?
2. have you tried switching batteries?
3. you still haven't said what you were doing with the device before this happend
4. this is totally unrelated to WM6 Forum, you shouldn't have posted this here
when you put your universal on usb with a pc on xp there is a detection? or not and are you sur that there isn t any write on the screen .
because i have the same pb in 2006 an ithink that my universal is dead an aftrer 2 day i put the universal on the light and i see v101 if you don t see to the light you don t see it because the backlight don t work.
in this case the led for the charging don t work to.
if you have this there is a solution with a free operator rom i think it s on my pc.if you need tell me
sudf said:
when you put your universal on usb with a pc on xp there is a detection? or not and are you sur that there isn t any write on the screen .
because i have the same pb in 2006 an ithink that my universal is dead an aftrer 2 day i put the universal on the light and i see v101 if you don t see to the light you don t see it because the backlight don t work.
in this case the led for the charging don t work to.
if you have this there is a solution with a free operator rom i think it s on my pc.if you need tell me
Click to expand...
Click to collapse
Thanks
It do not enter boot loader with light + power + reset and show no signs of life.
The light is off.when i push reset button flash the red light.
When connected to USB, PC reports "USB device not recognised"
I want a original rom for qtek9000 for test.
Anybody have this rom?
When I bricked my XDA Exec by means of hung program during the upgrade, I had: no reaction to normal Reset, no entry to Bootloader - basically a brick.
I did LeftSoftKey + RightSoftKey + Reset to do a *hard* reset (everything was lost anyway), and after that I could see "Serial... v1.01" Bootloader notification. When you connected that to a computer, it changed to "USB... v1.01" prompt.
So I just took JWright's image, and re-flashed it.
Guess what? It detected I had no image/extRom/RadioRom whatsoever then offered to re-flash them. I knew I'm OK when Radio upgrade progress indicator started to move.
It took me to get to another machine first, however. My Vista machine totally screwed up things, whereas my home XP managed to do the job.
Sitting on JWright's 2.02.02 now - very thoroughly made ROM, love Voice Command integrated with it instead of crappy Cyberon's software.
Dear all:
Been an avid XDA reader, I decided it was time for me to test one of these wonderful ROMs. I finally settled with the ROSE.
Then I started looking for the instructions on how to do this. I am following THESE, and then THESE instructions.
Instructions are pretty clear, but I run into a bit of an issue when following them.
Let me describe what I do:
1. Hard resetted the phone (I undestarnd is better to perform this with factory settings), verified I have 100% battery.
2. With the AS enabled, ran SDA_ApplicationUnLock.exe - Got confirmation
3. Ran uspl_116_jockyw.bat - Everything goes as expected (follow the on screen steps, got the Tux on the screen, screen goes off with backlight on, no leds, and the phone gets disconnected from the PC)
At this point, I am supossed to be able to run the FLASH.EXE app, but my phone does something strange: I can hear a USB device being connected to my PC (from the Windows sound), but AS does not connect to the device (it stays gray and says "Not Connected"), therefore, I am unable to follow the flash procedure.
If I unplug my phone and restart it (by removing the battery), the phone boots properly.
I have been searching this behaviour on the forum without success. Maybe someone has seen this and is able to provide any assistance.
Please leave comments or questions. Any feedback would be appreciated!
http://forum.xda-developers.com/showthread.php?t=510470
i have the same problem, strange?
Dude when u r running this file uspl_116_jockyw.bat a message will appear on ur vox screen just see to it that u press yes on ur vox..... then do the procedure as it is.........
good luck
hi when you reset the phone did you go into settings\connections\USB to PC
and UNtick the Enable advanced network?
hhs6789 said:
Dude when u r running this file uspl_116_jockyw.bat a message will appear on ur vox screen just see to it that u press yes on ur vox..... then do the procedure as it is.........
good luck
Click to expand...
Click to collapse
Thanks, but as I state on my description on point 3, I can follow that part of the procedure, is after that the problem appears.
deuse said:
hi when you reset the phone did you go into settings\connections\USB to PC
and UNtick the Enable advanced network?
Click to expand...
Click to collapse
Thanks! That did the trick. Unfortunately, I am getting the known Error at 3%. I see at the bottom of the instructions that you might get it, and that "Instructions are below". I have been trying to find some info on the forums, but I got a little confused. Do I need a software to flash the SPL?
Thanks hhs6789 and deuse for taking the time to answer!
Read this http://forum.xda-developers.com/showthread.php?t=330909
go down to were is says EDIT and follow the guild.
also you will need to run the application unlock first.
hope it works for you
Hi...
I was trying to Upgrade my O2 XDA Exec Rom with Windows Mobile 6.5 by explode. The process went successfully till 99% and after that it ended up with Error. Then I unplugged my pda from the pc and tried to restart the device. I was surprised that the device did not respond to any of the following
Soft Reset
Hard Rest
Boot Loader mode Start (Bulb + Power + Reset)
It is totally blank screen whatever you do.
When I connected the device to the pc with usb cable, a Red Light is shown for 2 seconds and then goes off and a message comes up on the pc that "USB DEVICE NOT RECOGNIZED".
Then I tried to Remove battery from the device for a whole night and the next day morning i did all the above procedures again to get no results.
Kindly Help me out
Thanks
Dinesh Kumaar
I think you have been bricked your device...
dineshkumaar said:
Hi...
I was trying to Upgrade my O2 XDA Exec Rom with Windows Mobile 6.5 by explode. The process went successfully till 99% and after that it ended up with Error. Then I unplugged my pda from the pc and tried to restart the device. I was surprised that the device did not respond to any of the following
Soft Reset
Hard Rest
Boot Loader mode Start (Bulb + Power + Reset)
It is totally blank screen whatever you do.
When I connected the device to the pc with usb cable, a Red Light is shown for 2 seconds and then goes off and a message comes up on the pc that "USB DEVICE NOT RECOGNIZED".
Then I tried to Remove battery from the device for a whole night and the next day morning i did all the above procedures again to get no results.
Kindly Help me out
Thanks
Dinesh Kumaar
Click to expand...
Click to collapse
if it's not recognized, remove the SIM card, the SD card, and on the PC open activesync and disable usb connections. for more info open this link
http://wiki.xda-developers.com/index.php?pagename=Uni_Stuck_Bootloader_Serial
what if the device is bricked
Thanks for your quick reply
Kindly let me know what could be done with the bricked device. Can it be repaired again.
Thanks again
Dinesh Kumaar
dineshkumaar said:
Thanks for your quick reply
Kindly let me know what could be done with the bricked device. Can it be repaired again.
Thanks again
Dinesh Kumaar
Click to expand...
Click to collapse
you have to find another rom and try to flash it to your PDA.
ARE YOU RUNNING windows XP on your PC?
Yes ! I have Windows XP SP2 and Active Sync Version 4.5.0 (Build 5096)
Thanks
dineshkumaar said:
Yes ! I have Windows XP SP2 and Active Sync Version 4.5.0 (Build 5096)
Thanks
Click to expand...
Click to collapse
have you tried to upgrade another ROM, and if you did, is your PDA now working?
I cannot update my rom as my pc cannot recognize my device. is there any other way to update rom?
dineshkumaar said:
I cannot update my rom as my pc cannot recognize my device. is there any other way to update rom?
Click to expand...
Click to collapse
Have you read here?
http://wiki.xda-developers.com/index.php?pagename=Uni_Stuck_Bootloader_Serial
Try to reflash with another ROM
Hope it helped
And don´t forget to vote!
I had already done those steps to get no results.
its my badluck.
If you cannot get into bootloader and you have done the steps above, then you cannot flash to another rom.......it would seem you now have a paperweight im afraid
I am still not able to revive my device. I know that it is just due to corrupt bootloader but don't know how to repair it.
If anybody ever has solution for this... kindly let me know.
Regards
Have you tested mtty?
I would recommend to PM a chef on Universal forum
Good luck,
Mtty is not detecting my device
it says can't open usb port
One More thing I have noted is that when I keep the device connected with the pc, at a certain interval of about 10-15 mintues my device's Led shows RED Light for few seconds and then turns off followed by the the "USB device not recognized" on my pc.
I hope this can be used as a hint towards reviving my device.
Regards
have you followed orbs advise above and pm a chef on that section, they maybe able to help. From my knowledge (limited on that device) i ddont think there is any recovery proceedure that you have not tried. Have u downloaded offical wm5 rom and tried it. I know and appreciate that it will probably not work due to corrupt bootloader, but what else is there to do??
To understand more, what did you do PRIOR to trying to flash to 6.5.
Did you hardspl correctly? Had you already flashed to another rom and just felt like flashing to another new rom?? Give us more detail.
Thanks for your reply
I dont know how to PM Chef.
I had used 3 other Rom versions of WM6.1 on my device. They ran very much fine on my device. But When i found WM6.5 xplode, I wished to try that too. But the rom update procedure went successfully till 99% and after that it showed an error that upgrade was not successfull. I pulled out the device and tried to restart if by all methods but I wasnt able to power on at all.
Thanks
Regards
ok, goto the thread that you got the rom off, click the chefs name and you will get a menu there to send pm, do it, he might have seen a similar problem or know how to correct bootloader.
good luck
noup really no...
Is bricked
my bro has bricked an Universal and the same led turns red no power off no bootloar no power it means the flash chip is dead!
Sorry to heard that.
He waits too long for the upgrade it tooks at least 40 minutes
then ERROR... but you know... the batt was died in middle process ( th batt was ****ed up, it say full charged but no! it was on 60 or 50%) then the stupid thing is make a hardreset.. i told him dont hR your device... justa simple reste and reinit the process... and huh! its bricked.
if you are interested on sell your parts
maybe my bro want some parts.
my advice(similar to other people):
1. Charge your batery somehow (in other device or anything else)
2. put your devce in bootloader mode and connect it to pc - it wll be detected like microsoft usb sync
3. use mtty try difrend versions becuse sometimes 1.42 does not detect it properly - read here for what to do with mtty
IMO this may be battery problem or nand chip problem - in both cases it is hardware fail
Hello!
I killed my PDA-it. 3 Color does not load mode. With or without the battery I found some 3 types of drivers shown in the picture. Not associated with MTTY, absolutely dead. : (
I'd be happy if you share with me some trick for possible recovery.
Thank you!
How did you brick it??
Do a search for QC diag drivers or MotoQ drivers install them.And download mtty.When the driver is installed check which port the diag driver is installed on and connect mtty to that port,then type cego a the type task 8 (this should reboot it.
press n hold camera & soft reset button. tri colour screen wii appear
Is dead "MTTY" and I want 3 types of drivers. MTTY claim 3 colors mode. Not associated with PDA. I have another PDA operating "Cruise" which is associated with "MTTY" without a problem. Will try with this kind of drivers: "MotoQ drivers" will tell the result.
Thank you!
the hard reset procedure is holding gps and internet button pressed for 2 seconds and without releasing them stick your stylus into the soft reset hole.
keep those two buttons pressed until the grey screen appears then release them and press the green button for confirmation and the green button again after it's done to reboot
Try to remove the battery and cable, wait 1 minute, insert the battery and start the device with pressed camera button.
When the tricolor appears plug in the cable, wait for USB message on your device and flash.
Dark Dragon
I have similar issue.
have a polaris whcic i can not make HR
tried almost everything.
Has HTC original rom but is stucke at alignment screen.
Need to make HR.
Tried camera+reset makes soft reset
tried gps+explorer makes SR
I can acess it trhoug active sync, can it help to make HR?
rpsilva said:
I have similar issue.
have a polaris whcic i can not make HR
tried almost everything.
Has HTC original rom but is stucke at alignmen screen.
Need to make HR.
Tried camera+reset makes soft reset
tried gps+explorer makes SR
I can acess it trhoug active sync, can it help to make HR?
Click to expand...
Click to collapse
i think if you see the calibration/alignment screen...windows recognizes the phone and usb and you can reflash the rom
martinasa said:
Is dead "MTTY" and I want 3 types of drivers. MTTY claim 3 colors mode. Not associated with PDA. I have another PDA operating "Cruise" which is associated with "MTTY" without a problem. Will try with this kind of drivers: "MotoQ drivers" will tell the result.
Thank you!
Click to expand...
Click to collapse
i ave in the past a similar problem....mtty did not recognizes the phone and usb...the solution for me was to start the same on a older windows xp pc...
Hello again.
Phone not come in 3 color mode.
martinasa said:
Hello again.
Phone not come in 3 color mode.
Click to expand...
Click to collapse
also not with: press n hold camera & soft reset with stylus ..?
what it makes after you start the phone..'?
Ok I had the same problem. Now i can enter in 3 colors. Make this:
Step 1. Download and read this:
http://forum.xda-developers.com/showthread.php?t=393337
You need motorola Q drivers and a Windows XP 32bit to work.
Step 2. Read the post of jpg001 of this link:
http://forum.xda-developers.com/showthread.php?p=5515006
You need use the files of jpg001 to work
Step 3. You need a mtty called "mtty_0513_Test.exe" because other version freezes, at least for me. If you need more information i will be here. I'm trying to Hard-SPL my Polaris to work.
[email protected] said:
i think if you see the calibration/alignment screen...windows recognizes the phone and usb and you can reflash the rom
Click to expand...
Click to collapse
the problem is that I do not have hardspl installed yet.
have flashed with original rom but the problem remains.
The main issue is that at boot is stucked at "tap the screen..." and want to make HR to see if helps.
Tried to install Hardspl but always an error and stays at 0%
I am assuming hardware problem with touch screen....
If you can help...
rpsilva said:
the problem is that I do not have hardspl installed yet.
have flashed with original rom but the problem remains.
The main issue is that at boot is stucked at "tap the screen..." and want to make HR to see if helps.
Tried to install Hardspl but always an error and stays at 0%
I am assuming hardware problem with touch screen....
If you can help...
Click to expand...
Click to collapse
than i think you also must use mtty (reset the phone)....from post above or here:
http://forum.xda-developers.com/showthread.php?t=425922
the best is to use windows xp for that
luzbel_es said:
Ok I had the same problem. Now i can enter in 3 colors. Make this:
Step 1. Download and read this:
http://forum.xda-developers.com/showthread.php?t=393337
You need motorola Q drivers and a Windows XP 32bit to work.
Step 2. Read the post of jpg001 of this link:
http://forum.xda-developers.com/showthread.php?p=5515006
You need use the files of jpg001 to work
Step 3. You need a mtty called "mtty_0513_Test.exe" because other version freezes, at least for me. If you need more information i will be here. I'm trying to Hard-SPL my Polaris to work.
Click to expand...
Click to collapse
very interesting....very interesting
[email protected] said:
very interesting....very interesting
Click to expand...
Click to collapse
Thank. 1 long week reading posts...
Now I'm flashing Oficial rom and seems to work!! It will revive !!
Ok! It's finish and work!! My polaris back to life!!