Any one - JAMin, XDA Neo, S200 Software Upgrading

hi all people
After a war lasted 1 month between ME and my jamin
i was managed to overcome him
but the prob that i cannt make restart of turne it off
if i do so i will be forced to conect the cutten AC to the battery connector
and the USB just for one second ( to press the power button ) after that i disconnect every thing and the mobile works best BUT i cannt resat it
ANY one dream with such a LUCK

well
the prob is solved
just change the IPL and SPL version

Related

downgrade problem

hey all,
i have tried to downgrade my qtek s200 with the CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE.exe software i found here.. after everything went quite well, when the phone restarted, the screen started to flash on and off.. and when i dont take the batteries out, the screen, the power led and the bluetooth led turns on and off repeatedly..
any suggestions on what i should do?
thanks..
i have exact the same proplem now
i have exact the same proplem now
Same Problem
Remove the battery - whait about 3 min. - plug ac power cable without your battery - put the battery - when the orange light on, turn on your device.
back to the life, but not solve the problem.
sorry my english, i´m from brazil. (don´t speak english)
sarpsuerdas said:
hey all,
i have tried to downgrade my qtek s200 with the CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE.exe software i found here.. after everything went quite well, when the phone restarted, the screen started to flash on and off.. and when i dont take the batteries out, the screen, the power led and the bluetooth led turns on and off repeatedly..
any suggestions on what i should do?
thanks..
Click to expand...
Click to collapse
Sounds to me that you tried to flash a Wizard-ROM on a Prophet.
This is simply impossible, so you probably bricked your device.
well its somewhat working i'm on a prophet bootloader ipl 2.09 spl 2.20 right now and i'm using a crossbow rom from the wizard section right now... (camera is not working).
what you could try is cut the charger wire open and attach the inner cable to the first battery pin (physical top) and the outer wire to the fifth pin. then go into bootloader, connect to computer and flash a prophet rom which has spl and ipl included.
dou you have a g3 or g4 device? on which spl/ipl are you right now...
I did the same thing with my s200.
I remove cable and battery, insert adapter cable and then battery until I get a steady amber light (usually takes 2-4 attempts).
When it boots up I quickly replace the adapter cable with the computer cable and Active Sync works.
I would like to reflash it but I can't since my battery is reporting 0% always, even when the battery is fully charged and it's not charging either. (And I can't get into the bootloader either.)
@crOssy: are the batteries different between models? and if so, would your proposed wiring actually work? have it been tested?

Did wm 6.1 kill my wizard???????????

hellow to all . i resently installed wm 6.1 on my wizard and eventualy the battery ran out ,so i connected the charger and to my suprise it did not charge so i tryed with another charger and the same result. the thing is it was working perfictly with wm 5.0 and ever since wm 6.1 this happend.to do the install i used awizard to do the ulocking bouth sim and cid then i down graded the IPL and then flashed the PTG rom and it worked perfectly intil the battery situation.when i plug the charger the red light turns on but thats all it does , and it stays that way for days in a row . ive tryed two diffrent battries. can any one help or give any ideas on this situation, thanks in advance.
Most likely you have flashed a G3 IPL and SPL to a G4 device. If it is the case, then sorry that you've got a brick.
the device is a g3 and ipl spl is g3 the olny thing im not sure about is the rom,here is the link from where i got it.http://forum.xda-developers.com/showthread...d=1#post2601705 , can any body tell me if g3 or g4 rom...thanks
please post the full link, its not complete..it gives a 404 Error
There is no G4-only ROM, all custom ROMs now are G3 and G4 capable.
Try to press the reset hole and see if it goes to RUU or not. If it still doesn't power off even though the charge light became green, then there may be a hardware error.
the problem you are experiencing imay be the amp on your charger.
Only an HTC wall charger can revive a flat dead battery.
This charger should say that it is 1Amp (1000ma)
If you use a charger from a motorola/blackeberry/USB charger it will not help you in this case.
Check your amp.
If you do not have an official wall charger, then the only way to revive is to get a new battery
yes i agree with SVI, because i myself faced this probm, when i got a new batt..i had to charge it fully firstt :/ but i went on with the upgrades..and the batt died on me..i used a motorola v3 charger but didnt work..then i went to the shop owner to replace it..and he said that there is a special chargers for these HTC phones, i bought that and its working perfectly now
hey guys thanks for the replies and ive tryed all those solutions ,the wall charger from my htc trinity and the wall charger from the qtek wizard it self and neather do anything.
the only thing that dose work is putting the battery from my trinity and holding it with my hand in place. it turns on but it dosent stay on for long .
it turns off in the following maner the screen starts going white and it stays that way.
i tryed going to bootloader mode and i succeaded but then it turned to the white screen.
changing the subject the IPL is 1.01 and the SPL is 2.18 the rom is a 6.1 ptg rom here is the link:http://forum.xda-developers.com/showthread.php?p=2601705&posted=1#post2601705 this link works i tested it. can anybody tell me if this rom is for g3 or g4 devices, the device with wm5 works fine . or can it be from the IPL and SPL not being the same. can any one tell me why this is happaning iv flashed so many devices and never had this problem . i my self have a qtek magicion, a htc trinity and a qtek prophet. well hope for some help thanks again.
Yes, first step is to ensure that you have a fully charged battery, a new battery is not fully charged so a desktop charger will be helpfull.
The IPL SPL difference is discussed by Dr Puttingham post
http://forum.xda-developers.com/showthread.php?t=285435 step 16
"Watch the rebooting of your PDA, if BOTH IPL and SPL are 1.xx then great. Quite probably your IPL will be 1.xx and your SPL will be 2.xx. Rerun the button 1.05 ROM downgrade a second time and it will become 1.x on both IPL and SPL. You don't need to redo the unlocking."
Hopefully you can maintain bootload (press and hold camera button on start-up) with the new battery
Anouther hopefully usefull post is
http://forum.xda-developers.com/showthread.php?t=276963
Best of luck
ademim said:
hellow to all . i resently installed wm 6.1 on my wizard and eventualy the battery ran out ,so i connected the charger and to my suprise it did not charge so i tryed with another charger and the same result. the thing is it was working perfictly with wm 5.0 and ever since wm 6.1 this happend.to do the install i used awizard to do the ulocking bouth sim and cid then i down graded the IPL and then flashed the PTG rom and it worked perfectly intil the battery situation.when i plug the charger the red light turns on but thats all it does , and it stays that way for days in a row . ive tryed two diffrent battries. can any one help or give any ideas on this situation, thanks in advance.
Click to expand...
Click to collapse
Its sounds like a battery drain partial brick. Under normal situations, the phone will shut down before the battery is completely drained. This is so you don't end up with a completely dead battery. Sometimes, like when the phone is frozen or at the bootloader screen it will run itself completely dead. It sounds to me like you have a completely dead battery. To charge under normal conditions, your battery has to have enough juice to boot the phone one more time. See, when you plug your phone in, if its not on, it will turn on. During boot, there is no connection between charger and battery...the battery has to have enough juice to make it through boot at which point the phone enables the charger. The way I fixed my battery brick was by cutting the end off of a usb cable, striping the wires, and jumping a charge onto the battery.
Please refer to this blog for a description of the steps involved in this process:
http://www.asktheadmin.com/2007/06/htc-wizardcingular-8125-dead-battery_21.html
could be as stupid as the ongoing connection initiated by activesync:
check the schedule settings and change it to manually.
http://forums.wireless.att.com/cng/board/message?board.id=samsung&message.id=62948

No more bootloader no more nothing, after rom upgrade s200

Hi All,
I've tried to upgrade the ROM of my QTEK S200.
It got completely stuck!!! I had to remove the battery. Now it stays black. Even a hard-reset does nothing. No bootloader, no white screen, nothing. It's like the device doesn't recognize the battery anymore. Same problem with another battery. When I connect the power supply, the light stays red for 5 seconds and then goes out again. No charging (orange) light.
Does this mean that the device was short-cutted (hardware problem) or can this be fixed with some manipulation?
Anybody an idea how I can fix the hardware (if broken) myself? Can't be to difficult if it just blew a fuse ;-)
Thanks
If the accu not charge, I think he is dead. You need a new one. For flashing new rom, you need a good acco over 50 %. Than you go to bootloader modus and flash a WM5 Rom WM5Rom.
coolb4all said:
Hi All,
I've tried to upgrade the ROM of my QTEK S200.
It got completely stuck!!! I had to remove the battery. Now it stays black. Even a hard-reset does nothing. No bootloader, no white screen, nothing. It's like the device doesn't recognize the battery anymore. Same problem with another battery. When I connect the power supply, the light stays red for 5 seconds and then goes out again. No charging (orange) light.
Does this mean that the device was short-cutted (hardware problem) or can this be fixed with some manipulation?
Anybody an idea how I can fix the hardware (if broken) myself? Can't be to difficult if it just blew a fuse ;-)
Thanks
Click to expand...
Click to collapse
Yep, hes dead alrite, make a good paper weight sorry bro...
not the battery
of course I tried a new battery
same problem
Can you make a downgrade to WM5 ? Ist the battery charged now ?
DC Adapter 4,5 V
I had the same problem.
Remove the battery and connect the pin nr 1 (nearest to the cam) to + and the pin nr 5 to -. I think 3,7 to 5 V is ok. Then bootloader and connect to computer.
Don't blame me if anything goes bad ;-)
how to proceed?
I've tried to do as explained...
I've taken an old charger (5v) and connected the cables (black/white striped to 1 and black to 5). I'm not 100 percent sure about + and -, but normally black is always -, if I'm not mistakin'
What should happen? How should I proceed?
My device does nothing... No light. Power button does nothing, hard reset does nothing.
Does this procedure work with a QTEK S200?
Maybe the charger (old gsm) is too old or broken?
Maybe + is black...
Sooo many options ;-)
Worked on mine S200
Of course You must know if the adapter is working and +/-.
When I connected 1 to + and 5 to - I could operate the mobile as if the battery was mounted and working.
My problem began because the battery isn't charging in bootloader mode.
And I'm still stuck there... Because it's a G4 device flashed with G3 SPL... Anyone got a suggestion how to solve this?
JustBored said:
Of course You must know if the adapter is working and +/-.
When I connected 1 to + and 5 to - I could operate the mobile as if the battery was mounted and working.
My problem began because the battery isn't charging in bootloader mode.
And I'm still stuck there... Because it's a G4 device flashed with G3 SPL... Anyone got a suggestion how to solve this?
Click to expand...
Click to collapse
I Did the same thing '''''HELP"""
What you should do
Keep the device on for 2 hours connect it to the electricity.
Install the original rom with the PDA connected like that to the PC, if it does not enter the Rom update continue trying by doing a hard reset with the stylus and pressing the left com button on the left side of the device, then retry the rom install, if it says unable to connect continue trying, using the procedure i explained before, thats what i did when the same stuff happen to me i was without my device working for a month, now i´m using WM6 with the Diamond Rom, so its possible, to do this you just have to keep trying.
my prophet is block and after try of hard reboot is dont turn on.. its not turn on on any way, no detect charger ether ( no red led ) battery was almost full when its go off..
plz help, can i try 1-5 pins solution?
srbwap said:
my prophet is block and after try of hard reboot is dont turn on.. its not turn on on any way, no detect charger ether ( no red led ) battery was almost full when its go off..
plz help, can i try 1-5 pins solution?
Click to expand...
Click to collapse
My friend. A few people have tried the pin method and one or two have succeeded. IMHO i would not try it, for fear of frying your phone, yourself or starting a fire.
Take out the battery for a good couple of hours. Take out SIm card and SD card. Put battery back in and try to charge for at least 5 hours, even if the light does not show (might just be LED issue).
Then see if you can start in boot loader, u now how to yes? (keep camera button pressed, soft reset with stylus, then let go of camera button after few sconds). What happens?
pins to power
I've tried connecting the extreme small pins to the (big) cables of the charger but nothing happens over here. The screen stays black.
To All,
Any hints on how to connect these cables to the pins, without the fact that they're constantly coming off the pins and constantly touching other pins?
You try and tell me about your experience ;-)
revive prophet revive ;-)
I was just playing with my qtek when I noticed that after connecting and disconnecting it to the AC for 5 times or so (with red light going on and off for a second), it tries to startup, but drops dead after a fraction of a second. Damned ;-) No chance of going into bootloader.
Almost there ;-))
coolb4all said:
I was just playing with my qtek when I noticed that after connecting and disconnecting it to the AC for 5 times or so (with red light going on and off for a second), it tries to startup, but drops dead after a fraction of a second. Damned ;-) No chance of going into bootloader.
Almost there ;-))
Click to expand...
Click to collapse
keep it plugged in for about 5 hours, dont play with it or turn it on lol, give a go unless u have done already and just havent said
Direct Connection to 220v doesn't work
The workaround of connecting the pins directly to the charger doesn't seem to work on a QTEK S200 G4.
Since mine is a G4, I wasn't lucky... I'm left with a cut charger cable.
I'll try to charge it for 5 hours but since no led is going on I don't think this will have any effect.
Listen keep it plug in to the electricity for 12 hours, then try to put it in bootloader mode by pressing the, com button on the left side of the device after you hard reset it, with the stylus after you manage to enter the bootloader mode, you only need to follow the steps described on several posts on the forum.
if nothing works connect the device and try to install the original rom, my device is a g3 so i´m not sure if the g4 works the same way.

spv c600 not starting

hello everybody.i have a problem with my spv c600.i bought it few days ago.i had installed some apps on it and next morning my phone was off,althought the battery was full.i made hard reset for three times and the phone started.but this is happening every morning from then.and now i can`t make hard reset.after it asks me to press 0 key shows orange screen and after that turns off.sometimes shows the windows mobile screen but only that and turns off.i don`t understand what is the problem...is it software or hardware problem?
can someone tell me what can i do?i want my phone back...i like it to much
sorry for my bad english
i`m not sure if i posted to the correct section but no one can`t help me?
Try to enter Bootloader (hold camera button and shortly hold Power).
After Bootloader started, you need reflash official ROM.
it enters in bootloader but it stays only 3 seconds and after that turns off.i`m going crazy....i don`t know what to do...is it the battery the problem?but last time when it worked the battery was full
other ideas?
try other battery, or try turn on without battery only power cable plugin.
the same thing without baterry.it stays 3-4 second and after that turns off.which is the problem?
and i don`t understand what is with the led colour.when i put the phone to charger the light is red...i try to make hard reset but the phone turns off and and one cuple of times...the led color becomes orange and green sometimes...
so?what is going on?
can someone help me please?
I think that it is hardware problem. Before am I bought my HTC Tornado, I had Sony Ericsson P900 and after 2 years using suddenly he after power on he stopped at the introductory animation. So I gave it to the service and told me that is it a problem with the motherboard. Your SPV C600 looks that is on it similar.
and what happend with your tornado?
With my Tornado nothing. The hardware problem was in my Sony Ericsson P900. In service told me that is it a problem with the motherboard and that the correction would cost cca 850$ . So I declined correction and bought HTC Tornado, which still works .
oh..thanks anyway.i think i will go to service with my spv...
wow it didn`t started for 2 days and now is working like is new.i don`t understand...where is the problem?
it worked only 2 hours and after that it was dead again
what can i do to fix this problem.it`s ok to change the rom?
fixed.i sold the phone

Problem WM6.5,

Hello guys, first of all i would apologize for my last thread in which i posted a ware, im sorry for that. Anyways i have a problem. I updated my SDA with WM6.5.21234 Standard by Gregory Full. I've been using it for 2 weeks and today i installed the HTC Tornado Radio 02.61.01 from this post (b : WM6 => "the remote party has ended this connection") (i cannot post the link :s) ... and now when i switch on the phone the 1st load screen comes and the mobile is switched of I even tried re-flashing the ROM but no luck.
How far did the flash of the radio package succeed? There is a distribution file that updates the IPL + SPL before the Radio - the flashing stops at several % values but it must continue to 100% and do an automatic reboot.
What do the lines say on the 3-color screen if you go to the bootloader mode?
everything went well, the phone restarted automatically after installation and never turned on =( ... it say's
IPL 1.00
SPL 1.00.0014
Tornado IU
Are you sure about 1.00 for IPL and SPL?
They are quite old - the latest are 2.00 and 2.0..14
I suggest the following sequence:
1.) load the stock ROM from your operator -> check the status for IPL and SPL
2.) update to the latest IPL and SPL and Radio with the combined package from Nitrogens tagline -> check if the Stock ROM still works
3.) load the cooked ROMs as the cooks indicate to do (take care about the format BINFS <size>)
i ddnt get the first step
oooh yeah Thnkx alot man this forum rocks its ok now =)
thnkx for your help
The stock ROM is the one that is on the orginal device as it is "on stock" when you buy it in a shop. As you have Super-CID your device already, you can take any other Tornado "stock" ROM from any vendor - as you like.
The advantage of stock-ROMs is that they are usually complete and everything in there matches to the other. So if such a ROM works - your device does not have problem.
Then you can start to replace pieces one after the other...
got it .... thanks for your help =)
I'm in a little bit of a problem with my i-mate sp5. i upgraded to the wm6.5 and now the orange light by the ear piece keeps flashing as if its charging even when its not plugged it. everytime i restart it i get a different battery level. i brought a new battery and it does the same thing but it doesn't charge. any suggestions? This my i-mate burnt up?
Get back to a stock ROM to see if it is a device problem. If it works ok with the original ROM, then the battery and/or LED driver are screwed in the WM65 ROM. Be sure you load a ROM that has the proper Tornado OEM drivers cooked into it.
Yea i tried that too. Im still not about to charge it fully. the phone seems to get hot too. I thing maybe the phone is burnt out. Is there a place where i can use it as a trade-in or have it refurbished or is it best i jus buy a new one
yea i tried that already. it does the same thing. the phone wont died unless i take it off the charger but it will not charge all the way with either battery and the phone is always hot. with the old battery the charge icon stayed up even without the charger being connected but the charge icon never comes up for the new battery even if the charger is connected. with the new battery it charges a little then it will die very fast because its still tries to charge itself after i disconnect the battery. one time i set the cpu to 228mhz and it overheated and wouldn't come back on until i flashed it again. you think thats th problem? maybe theres a burnt out board or something
The HW controlling the charge is controlled via 2 different methods:
- phone off: the bootloader
- phone on: the windows driver
If the "phone off" gives the same results - try a different battery. The HW inside the phone is hard to break imho.

Categories

Resources