i have an i607 and it handed wen i went on gprs for browsing.i try to flashed it wid
SGH-i607 WM6 Upgrade
i also have active sync and its modem drivers all r perfectly installed but wen i try to conect the fone i saw the following on screen
USB Initial: OK
PC Connection: Fail
[Phone] Active OFF
[PDA] USB Cable Power OFF
how to solve my problem.plz some body help me
See you this is compatible
Samsung I 607
Can i flash a samsung i 607 with any of these roms ??
Thanks
Yes. You can upgrade with all any ROMs for i607
1. Windows XP
2. Change connect menu: Setting--> connection--> USB-> change to Modem: Computer receive information modem mode for Boot ROM in the next step
3. Turnoff and turnon to Boot mode. and plug USB cable and UP ROM
Good luck
Related
When I start upgrading ROM (Qtek 1.11.00 final) my mini struck at boot loader screen and my PC struck at
"Checking the information from your device...please wait...
Don't disconnect your device from PC or power supply until
the upgrade is completed "
I have strucked at this screen for an hour
what should I do ? Please help me . Thank You
I think you have not disabled the activesync USB connection yet. Do so, and reconnect your mini to your laptop/pc via USB again. then run the installation program again, u should be alright.
tt's what I faced earlier.
zenkinz said:
I think you have not disabled the activesync USB connection yet. Do so, and reconnect your mini to your laptop/pc via USB again. then run the installation program again, u should be alright.
tt's what I faced earlier.
Click to expand...
Click to collapse
I've tried this and I'm still stuck in the opening screen. Any other advice?
Regards,
Rajesh
rajeshr said:
zenkinz said:
I think you have not disabled the activesync USB connection yet. Do so, and reconnect your mini to your laptop/pc via USB again. then run the installation program again, u should be alright.
tt's what I faced earlier.
Click to expand...
Click to collapse
I've tried this and I'm still stuck in the opening screen. Any other advice?
Regards,
Rajesh
Click to expand...
Click to collapse
1. first mini must be in bootloader mode (screen will show serial)
2. disable USB in activesync, plug mini to USB cable (new hardware detection should occur and mini screen will show USB instead)
3. USB cable direct connect to laptop/pc..dun use USB hub..
should work..
Even I had the same problem
Thanks a lot it is solved now 8)
my uni stuk at boot screen serial v 1.01 the serial word didnot change 2 usb my desktop pc tell me that usb device not recognized i try all method nothing just boot screen
i try more than one usb cable
i charg my battry full
mtty not have usb choise
when i make hardrest the screen give me press 0 or x
i try the UNI_ExitBootloader.exe not working
i change many pc
i try 2 rest an hard reset 1000000 time
when i plug the usb cable in my device whitout battry it flash red
when i plug the usb cable in my device whit battry it not flash
i try all thing not work tell me that my device dead ???????????????????????????????????????????????
pllllllllllllllllllllllllz help 2 make my uni a live
I assume you have read the following 2 links? If not, read them now and follow the instructions very carefully.
http://wiki.xda-developers.com/index.php?pagename=Uni_Stuck_Bootloader_Serial
http://wiki.xda-developers.com/index.php?pagename=Uni_Stuck_Bootloader
I had the same problem as you, and was able to restore my Uni with a new ROM using the second link.
But the first problem is getting your PC to stop displaying "USB device not recognized", unfortunately this is quite difficult and I actually didn't manage to do it with my main PC! I had to use an old laptop with USB 1.1 and only then it worked fine, after installing Activesync 4.5.
Basically the Uni sucks full 500mA out of the USB port, so try unplugging ALL other USB devices from your PC first, and if that doesn't work then you will have to try another PC. Some work better than others, maybe you have an old laptop lying around which has at least USB 1.1, or could use a friends PC?
Don't bother hard resetting any more, in this state you can only do normal reset and enter bootloader mode. You will have to try combinations of this whilst plugging it into the PC, and also try different USB ports. Also try entering bootloader mode whilst the Uni is plugged into PC, and try without and plugging it in after.
If you manage to get the device recognized in device manager, and the display change to USB, then follow the instructions in the Wiki above and your device will be restored.
And make sure to flash a ROM that does not include a new IPL/SPL, that means don't use any network default WM5 ROM!!! I used Tomal's 8.0, I recommend that when flashing to recover your device.
thanxxxxxxxxxxxxxxxxxxxxxxxxx my jasjar back a live thanx every one
yasoo157 said:
thanxxxxxxxxxxxxxxxxxxxxxxxxx my jasjar back a live thanx every one
Click to expand...
Click to collapse
can u tell me how u got ur uni working again im still stuck at the screen where it says press x to restore defaults and 0 to exit????
jasjar died
I have exaclty the same problem with my jasjar. help!!! usb is not working .....and how can I find Tomals 8.0 ......
i upgraded to tomal's rom to give it a try, and it works great, problem is i can't remove the rom....mtty tool doesn't work cause everytime i connect to xp, vista don't matter about 10 cords it always say usb unrecongized and when i do the ruu...i get a error so i was going to try the mtty but i can't even connect the universal to the damn pc, in bootloader it goes from serial to usb when you connect that works, but u see it connect to the pc for like 2 secs then the usb unrecongizeable any help i'm tired of reading all these treads....thanks in advance
bty mtty tool only shows com1 and com2 no usb at all
I found out what it was, i had to go in to safe mode and when i plugged it back in i hurry up and stop the auto update, looked in device manager and there it was *** pocket usb sync **** before i couldn't see it now i followed the post on upgrading using vista no problems thanks!!
Mods
Can delete this thread please?
Can someone plz give me a full guide on flashing it on vista because i keep getting stuck and all the guides keeps messing me up so i get even more stuck.
Foe one when i plug in my phone in downloader mode and try to update drivers it says my drivers are already up to date and when i start the image downloader i get
[StartDownload => 0] StartDownload !!
[-] Connect and Power-on the Device.
[-] Device Not Found.
Can someone plz give me a full guide
install windows mobile device center
run phone in bootloader mode
uncheck allow usb connection
connect cable to pc
manually update samsung mits usb sync with vistaruu driver (wceusbsh.inf)
then turn on your phone, accept allow usb connection and synchronize it with windows mobile device center
when synchronization is complete uncheck allow usb connection
remove usb cable, run phone in bootloader mode,start
image downloader connect usb cable and wait a moment then start flashing
VistaRUU driver: http://www.fileden.com/files/2010/1/18/2729115//VistaRUU.zip
Alright thank you I'm gonna try in a little bit and I'll post how things go
OK Good luck.
alright i finally got it to work thx for the help
Hello frinds,
I cant connect my s2 plus to pc
Tried reinstalling kies and drivers
When i try to connect i get a message "SAMSUNG mobile USB Composite Device Faild"
I think there is problem with PhoneUtil
I think i changed it for some purpose
How to configure it ?
I have options
UART
Modem
PDA
USB
MODEM
PDA
Or any other problem ?
Please help me
Thanks