Related
I followed Dr. Puttingham's thread and Yippie's thread to a tee in addition to reading threads in this forum for a good number of hours each day for two weeks. Yesterday, I became brave enough to downgrade my 2.26 Ipl / 2.26 spl; GSM 2.25.11; OS 2.26.10.2 MDA with a goal to upgrade to a custom WM6 rom with touchflo.
* Started with flashing the button rom then cid unlock with lockwiz2b which looked successful no errors but got a 1.xx IPL / 2.26 SPL since I got a 2.26 SPL then
* flashed the wizard love rom then then cid unlock with lockwiz2b which looked successful also but got the same results - a1.xx IPL / 2.26 SPL again then
* flashed the 2.26 T-mobile rom from the Tmobile website then
* flashed NBD 8.3 only to go back to Tmobile's 2.26 rom - DISAPPOINTED after two hours...............
Any assistance would be appreciated without bricking my MDA. Also, I read the thread on how to install a 2.x rom in a cid locked G3, this method appears a little bid complicated and if I need to move forward with this method, would this method work for any WM6 rom with touchflo and if somebody could simplify the method in layman's terms for newbie's like me could understand, please advice.
Let me know if I missed anything in the process.
Thanks, Technobuff
After u do cid unluck and sim unluck and its reboots do a downgrade again to the button rom and ur ipl and spl will change.(u do not have to re-due the onlucking procedure again)
I tried again performing Dr. Puttingham's CID unlocking process in terms of flashing the button rom then the CID unlock process using Lokowiz2b but while I am at the DOS screen trying to CID unlock my MDA it the DOS screen showed unlocking phone........DO NOT DISCONNECT UNTIL THE PHONE REBBOTS.
This process went on for 5 then 10 then past 30 minutes until I gave up. To be on the safe side I turned off the LAPTOP by taking the battery then pulled the USB cable from the PC to the MDA.
What is the typical timeframe for the unit to CID unlock? Why is is it hanging? Am I missing or skipping the process? How can I complete the process?
Any help would ber greatly appreciated by newbies who read threads.
Technobuff
The problem is that you need to have an IPL/SPL of 1.xx before you try to unlock your phone. CID unlocking will not change your SPL which means that you had an IPL of 1.xx and an SPL of 2.26 before you even tried to unlock. You need to reflash the button ROM over and over until your IPL and SPL both show 1.xx and then run lokiwiz.
dont get your point, i have been using shelltool for ages without any problems and quite a lot custom roms. my SLP/IPL is 3.08.
regards
irm
unlock problem
if your device doesn't reboot almost at once after the unlock, it probably didn't work. That is what happened to me. Did you get four lines of File cannot be opened or a similar message? I got that from following the 17 steps carefully. What was wrong for me was unzipping to the root directory of C:/. When I redid it to the desktop and executed from there, no problemo.
Your symptoms sound exactly like mine. I posted a longer thread, somewhere....
LH
Ok i did a little booboo and yesterday was using equinoxe's softspl tool by mistake (didn't notice i had a g3), this causes you to actually end up with the exact same os you had before you flashed.
The best advice I can give: Open the Dr's guide and follow every step closely. (also just found this guide. Its a bit simpler http://forum.xda-developers.com/showthread.php?t=305225)
Once you CID unlock you should be able to use the RUUs to flash.
Make sure everytime you do any of the steps that dr. putt gives to be comepletely synced to activesync.
Also dont forget to load enablerapi.cab on your wizard.
Also you must use the unlock function before the cid unlock function in lokiwiz.
OH also the unlock will work after your ipl drops to 1.xx After you do the unlocks reflash button to drop the spl to 1.xx Then just flash up to a higher IPL/SPL as the Dr states.
If it seems unorganized im sorry =P
4irm said:
dont get your point, i have been using shelltool for ages without any problems and quite a lot custom roms. my SLP/IPL is 3.08.
regards
irm
Click to expand...
Click to collapse
Umm I believe the IPL/SPL of 3.08 means your phone is unlocked... so you really shouldnt need to use shell tool. Some correct me if I'm wrong
slod said:
Umm I believe the IPL/SPL of 3.08 means your phone is unlocked... so you really shouldnt need to use shell tool. Some correct me if I'm wrong
Click to expand...
Click to collapse
Just cause you have 3.08 does not mean you are unlocked..you could have upgraded a 2.xx ipl/spl without having downgraded and unlocked first.
thanks. helps me to learn stuff.
CID???
how wil i know if my fone mda vario is CID unlocked?
it is now installed with t-mobile 2.26 ROM
thanks.
rizortiz
famewolf said:
Just cause you have 3.08 does not mean you are unlocked..you could have upgraded a 2.xx ipl/spl without having downgraded and unlocked first.
Click to expand...
Click to collapse
right, i installed the latest german t-mobile rom and my device is still locked. the point i made is why the hell does somebody want to downgrade? It doesnt matter if u use the shelltool.
regards
irm
4irm said:
right, i installed the latest german t-mobile rom and my device is still locked. the point i made is why the hell does somebody want to downgrade? It doesnt matter if u use the shelltool.
regards
irm
Click to expand...
Click to collapse
Perhaps they want it actually cid unlocked for resale value...or perhaps they prefer the RUU method of installs vs having to use shelltool.
Hi I have a G4 Prophet and the IPL and SPL version number reads 2.10.0001.
I would like to flash it to use a WM6.1 ROM with the touchflo type functionality and new IE Mobile features (i.e. zooming).
I have read through all the guides about carrying this out and have even started having a go but am getting confused about HardSPL.
From what I read HardSPL CID Unlocks your phone so that you can install a diffeerent Carrier (e.g. Orange, Vodaphone) ROM ... or in fact a home 'cooked' ROM off of this site.
I have tried manually carrying out the HardSPL using both the Prophet Tools GUI and the command line batch file HardSPL however after the procedure finishes my IPL and SPL do not read differently as all posts indicate (i.e. they do not read 2.G4.4PDA) ... instead they remain as 2.10.0001.
I have seen the phone go to the tri-colour bootloader screen and even the progress bar go up correctly however when it reboots it says 2.10.0001. I'm assuming that I cannot go ahead and flash with a ROM (such as the Shadow TE one until the SPL reads 2.G4.4PDA).
Can anyone offere me some help with getting to this?
Many thanks.
Nick (a very much noob!)
nisgar2k said:
Hi I have a G4 Prophet and the IPL and SPL version number reads 2.10.0001.
I would like to flash it to use a WM6.1 ROM with the touchflo type functionality and new IE Mobile features (i.e. zooming).
I have read through all the guides about carrying this out and have even started having a go but am getting confused about HardSPL.
From what I read HardSPL CID Unlocks your phone so that you can install a diffeerent Carrier (e.g. Orange, Vodaphone) ROM ... or in fact a home 'cooked' ROM off of this site.
I have tried manually carrying out the HardSPL using both the Prophet Tools GUI and the command line batch file HardSPL however after the procedure finishes my IPL and SPL do not read differently as all posts indicate (i.e. they do not read 2.G4.4PDA) ... instead they remain as 2.10.0001.
I have seen the phone go to the tri-colour bootloader screen and even the progress bar go up correctly however when it reboots it says 2.10.0001. I'm assuming that I cannot go ahead and flash with a ROM (such as the Shadow TE one until the SPL reads 2.G4.4PDA).
Can anyone offere me some help with getting to this?
Many thanks.
Nick (a very much noob!)
Click to expand...
Click to collapse
I would recommend you use something like: http://forum.xda-developers.com/showthread.php?t=353547 It makes it a one stop upgrade... That uses "JumpSPL" rather than HardSPL which is the short term option.
Thanks for the help I tried the alternative lazy tool and it worked (http://forum.xda-developers.com/showpost.php?p=2141436&postcount=188) now my Orange SPV M600 has the Shadow Touch edition rom on it with the shadow cube addon, so far works a treat.
I would still be interested to know why the SPL version number did not change using the prophet tools or HardSPL on its own.
Anyway many thanks again.
Nick
nisgar2k said:
Thanks for the help I tried the alternative lazy tool and it worked (http://forum.xda-developers.com/showpost.php?p=2141436&postcount=188) now my Orange SPV M600 has the Shadow Touch edition rom on it with the shadow cube addon, so far works a treat.
I would still be interested to know why the SPL version number did not change using the prophet tools or HardSPL on its own.
Anyway many thanks again.
Nick
Click to expand...
Click to collapse
What is your devices IPL?
It may be because Soft/Jump SPL was not executed properly prior to HardSPL (this is automated through the HardSPL tools and Prophet Tools).
HardSpl Problem
l3v5y said:
What is your devices IPL?
It may be because Soft/Jump SPL was not executed properly prior to HardSPL (this is automated through the HardSPL tools and Prophet Tools).
Click to expand...
Click to collapse
i ran upgrade_hardspl_g4 on my prophet, my spl is 2.15 still... what should i do l3v5y? tried flashing it 5 times still no luck. Please help, having a hard time upgrading roms...
ipl: 2.20
spl: 2.15
im currently downloading prophet tools 2.8. i currently flashed my 818 with PV_temp rom. i'll try to install the prophet tools and hardspl my phone with it.. hope it works...will update in a few after the installation is done... downloading so slow... =(
*-----------------------------*
i did it!! thanks!!!
I made it, use SoftSPL.
Hey people.
I bought a TYTN2 off ebay and the previous owner already flashed Duttys rom 29th April onto it. he told me that he applied a HardSPL and flashed the rom.
My question is, I want to flash laurentius diamond V9 rom but I'm unsure if I need to start from the beginning, CID unlock and sim unlock and then apply HARDSPL again or can I just go straight to changing the SPL to version 3.56 and then install the new rom. Which path do you think I should take?
As i'm not entirely sure what the previous owner did to install the Dutt's Rom.
I have been reading the Wikis and FAQ's but i'm still unsure in my situation as i'm not sure what the phone has had done to it in the past.
Hold your camera button down and see if you even need to update to hardspl 3.56. If you do, then update your hardspl and then just flash whatever rom you need....note you may also need an updated radio. In any event, it will not hurt you by starting all the way over.
soupz said:
Hey people.
I bought a TYTN2 off ebay and the previous owner already flashed Duttys rom 29th April onto it. he told me that he applied a HardSPL and flashed the rom.
My question is, I want to flash laurentius diamond V9 rom but I'm unsure if I need to start from the beginning, CID unlock and sim unlock and then apply HARDSPL again or can I just go straight to changing the SPL to version 3.56 and then install the new rom. Which path do you think I should take?
As i'm not entirely sure what the previous owner did to install the Dutt's Rom.
I have been reading the Wikis and FAQ's but i'm still unsure in my situation as i'm not sure what the phone has had done to it in the past.
Click to expand...
Click to collapse
soupz said:
Hey people.
I bought a TYTN2 off ebay and the previous owner already flashed Duttys rom 29th April onto it. he told me that he applied a HardSPL and flashed the rom.
My question is, I want to flash laurentius diamond V9 rom but I'm unsure if I need to start from the beginning, CID unlock and sim unlock and then apply HARDSPL again or can I just go straight to changing the SPL to version 3.56 and then install the new rom. Which path do you think I should take?
As i'm not entirely sure what the previous owner did to install the Dutt's Rom.
I have been reading the Wikis and FAQ's but i'm still unsure in my situation as i'm not sure what the phone has had done to it in the past.
Click to expand...
Click to collapse
1. You should determine what SPL you have on your device FIRST
2. if you are doing a 6.1 ROM you will want a 3.xx HARDSPL installed -
3. the WIKI is your friend here - it will tell you how to determine what SPL you have and show you how to upgrade to what you need.
Once you have the CORRECT HARDSPL on your device and you understand the process you can continue - continuing before you understand and have the correct HRADSPL will guarantee that you need help for a bricked phone.
This is not hard - many have gone on before you ...
But you must read and understand.
Bill
Hey thanks for replying guys. Been reading through the SPL Wiki, but cant find how to determine your SPL.
ajmoncrief: Do I soft reset and hold down the camera button?
whk: Thanks for your advice. I have been reading the wikis for a while but I guess it will take a few more days of reading as I find it confusing with all the technical terms etc.
There is one bit which I would like clarification on if possible. in the thread 'http://forum.xda-developers.com/showthread.php?t=396235' is states:
'The reasoning is that those HardSPLs are what allows you to flash a ROM not originally meant for your device (from your vendor/region).
Once you have flashed the HardSPL you can then flash your ROM.
Once your ROM is flashed, you can then flash the SPL which matches that ROM to ensure stability. However, if you want to flash a new ROM, you have to go back to the beginning and flash the HardSPL again to allow you to load another ROM!*
from what I read,
Im assuming that if the previous owner flashed HARDSPL ver 1.xx and then loaded duttys April 29th 6.1 rom. I would need to now reflash HardSPL ver 1.xx again and then jumpSPL to ver 3.56 and then flash the new rom?
soupz said:
Hey thanks for replying guys. Been reading through the SPL Wiki, but cant find how to determine your SPL. ..snip..
from what I read,
Im assuming that if the previous owner flashed HARDSPL ver 1.xx and then loaded duttys April 29th 6.1 rom. I would need to now reflash HardSPL ver 1.xx again and then jumpSPL to ver 3.56 and then flash the new rom?
Click to expand...
Click to collapse
Read this -
http://wiki.xda-developers.com/index.php?pagename=HTC_Kaiser#ROMx20.Upgrading
This will help you figure out what SPL you have installed -
http://forum.xda-developers.com/showpost.php?p=1846653&postcount=800
and this:
http://wiki.xda-developers.com/index.php?pagename=KaiserIntroductionToROM_Flashing
I believe that once you have HARDSPL on your machine it is there permanently - until you flash another one over it - SO - You can go right from HARDSPL 1.0 to 3.xx and then flash your new ROM.
Bill
Thankyou very much for your advice.
I managed to update to HardSPL 3.56 and flash the new rom. All went smoothly (nerve racking) and everything booted up fine. Now i'm just exploring and tweaking the settings.
I couldn't have done it without your guidance and of course the help from wiki and FAQ's.
Cheers!
Just so I don't get flamed to bad for asking a what some would consider a simple question, I had an 8525 that I made SuperCID and HardSPL, so I have done this before. I have also read the majority of material in the wiki and the forums on what I would like to do.
So here goes,
I just purchased the Tilt and am looking to do the same. It is stock to the block right now.
ROM 1.62.502.0
Radio 1.27.14.09
Protocol 22.45.88.07H
My question is what is the sequence of events that I need to do in order to get my phone SuperCID and HardSPL to the point I can start using some of these wonderful 6.1 ROMS?
What HardSPL? v1.0? 3.56? I would guess 3.56 and that it should be the first thing I do.
Now what SuperCID? I found 2, here http://forum.xda-developers.com/showthread.php?t=361236 and here http://forum.xda-developers.com/showthread.php?t=375583
Any guidance would be very appreciated.
Thanks for your help
JD
The hardSPL depends on the ROM you're going to flash. Some ROMs work better with certain SPLs. Check.
For ease of mind, hardSPL first then security unlock. You can't go wrong in that order.
JudgeDredd67 said:
Just so I don't get flamed to bad for asking a what some would consider a simple question, I had an 8525 that I made SuperCID and HardSPL, so I have done this before. I have also read the majority of material in the wiki and the forums on what I would like to do.
So here goes,
I just purchased the Tilt and am looking to do the same. It is stock to the block right now.
ROM 1.62.502.0
Radio 1.27.14.09
Protocol 22.45.88.07H
My question is what is the sequence of events that I need to do in order to get my phone SuperCID and HardSPL to the point I can start using some of these wonderful 6.1 ROMS?
What HardSPL? v1.0? 3.56? I would guess 3.56 and that it should be the first thing I do.
Now what SuperCID? I found 2, here http://forum.xda-developers.com/showthread.php?t=361236 and here http://forum.xda-developers.com/showthread.php?t=375583
Any guidance would be very appreciated.
Thanks for your help
JD
Click to expand...
Click to collapse
Ok, so I don't know about the super cid process but here's at least how you can start the journey:
Copy KAIS_SSPL onto your device
take out sim card and SD card
run KAIS_SSPL
Unplug USB wait 5 -15 seconds, plug in.
Run the Hard_SPL of your choice depending on your ROM choice. Seems like the ones out there are using 3.56, but it varies
Make sure to also flash a compatible radio!
Viola! you are done and ready to flash a ROM!
JudgeDredd67 said:
J
What HardSPL? v1.0? 3.56? I would guess 3.56 and that it should be the first thing I do.
JD
Click to expand...
Click to collapse
1.) Flash 1.1JockyW HardSPL
2.) Using Jockys SuperCID process security unlock your device.
3.) Flash to any other HardSPL
4.) Flash the ROM of your choice.
Thank you all for your comments. I feel a lot better going into this now.
Noob question sorry. Sequence of events....
Appologies in advance as this is obviously a nooby question....
I have just aquired a t-Mobile branded MDA Vario III. I want to CID/SIM Unlock it as well as Hard-SPL it so I can install whatever ROMs I would like.
I previously had a HTC Wizard that I CID & SIM unlocked with the Lociwiz tool, however I had to downgrade the IPL/SPL to version 1.x to get this to work. Once it was unlocked I was able to install any ROM. I am looking for a similar thing with my new Kaiser and I can't find a Wiki or guide explaining the steps. It seems there are 1.x HardSPL's as well as Security unlockers, plus 3.x HardSPLs but no definitive guide as to the correct sequence.
1. I want to unlock the phone so I can use any SIM
2. I want to unlock the phone so I can install any ROM
With the Wizard I had to downgrade IPL/SPL run the Lokiwiz tool and the upgrade to whatever I wanted. How do I do the same with the Kaiser?
Sorry....
Andy
ADB100 said:
Appologies in advance as this is obviously a nooby question....
I have just aquired a t-Mobile branded MDA Vario III. I want to CID/SIM Unlock it as well as Hard-SPL it so I can install whatever ROMs I would like.
I previously had a HTC Wizard that I CID & SIM unlocked with the Lociwiz tool, however I had to downgrade the IPL/SPL to version 1.x to get this to work. Once it was unlocked I was able to install any ROM. I am looking for a similar thing with my new Kaiser and I can't find a Wiki or guide explaining the steps. It seems there are 1.x HardSPL's as well as Security unlockers, plus 3.x HardSPLs but no definitive guide as to the correct sequence.
1. I want to unlock the phone so I can use any SIM
2. I want to unlock the phone so I can install any ROM
With the Wizard I had to downgrade IPL/SPL run the Lokiwiz tool and the upgrade to whatever I wanted. How do I do the same with the Kaiser?
Sorry....
Andy
Click to expand...
Click to collapse
Since you are a Senior Member, you should already know the first rule is to search before creating new threads. However, since I am in a good mood from starting my new job this week, I will "help" you out. Check out the threads below, and after some in-depth reading, all of your question will be answered.
HardSPL: http://forum.xda-developers.com/showthread.php?t=334679
Sim Unlock: http://forum.xda-developers.com/showthread.php?t=361039
Now here is your nickels worth of free advice: Do NOT attempt to run the SIM Unlocker with a WM 6.1 ROM or the 3.xx HardSPL installed.
Closing this thread so it can fade away....
Hey guys! been lurking around the forums for eons, but haven't 'dove in' till just recently. Have a couple of questions.
Some months ago I did the free upgrade to WinMO 6.1.
I got Tilt SID unlocked by calling up AT&T and telling them I was going to Europe. My T-mobile SIM card is working just fine.
After a few hours of cussing, I managed to beat HardSPL 3.56 into my phone, because it already had SPL 3.56 on it.
Now I'm stuck trying to CID unlock and I can't seem to find a utility to work with it. The 'chain' of threads I followed dead ended saying downgrade to get it work, but I don't want to do that. I had a hard enough time getting HardSPL 3.56 to install. Then I ran across Jockyw's CID unlocker http://forum.xda-developers.com/showthread.php?p=1837147 and found myself saying ooo and ahh! But, it won't work with ANY 3.xx HardSPL.
Is there a CID unlocker compatible with 3.56??
I'd love to have AT command mode stuff and etc. from jockyw's, but at this point I think I'll take whatever I can get without needing to downgrade.
I can't seem to find it now, but didn't there used to be a list of pre-cooked ROMs here somewhere?
I think what I'm aiming at is a fully patched / hacked 6.1 HTC ROM with everything fixed and no bugs. Preferably minus any bloatware. If it has recommended utilities pre-installed great, if not, no big loss. Did they ever finish hacking a video driver together? I lost track of that thread, and can't seem to find any current info.
I've been waiting for a working Linux distro for a HTC device for years, but I'm going to throw in the towel and make the best of what I can get on windows. I've spent over $3000 on these HTC devices over the years, but don't rely on them because of all the bugs. Once I get my Tilt patched up, I'm jumping ship and trading in my old ones for a G1.
Thanks for any help!
p.s. I DO have to CID unlock before I can install any other ROMs.. right??
p.p.s. Here's all the details if it's any help:
rom version 3.57.502.2 WWE
rom date 7/17/08
radio version: 1.65.21.18
protocol version: 25.88.40.05H
tri-color screen
KAIS1*0
SPL-3.56.0000
CPLD-8
.
.
Serial
image version 3.57.502.2
R 1.65.21.18
G 25.88.40.05H
D 3.57.00.00
Note: This is BEFORE I updated to HardSPL 3.56
Thanks again!
If you have any of the HARD SPL installed(3.56 from your words).
You can flash any ROM you want.
No need to CID unlock separately.
With Hard SPL, your Device is CID unlocked already.
Your pda doesn't not have hard spl installed on it
Crogon said:
Hey guys! been lurking around the forums for eons, but haven't 'dove in' till just recently. Have a couple of questions.
Some months ago I did the free upgrade to WinMO 6.1.
I got Tilt SID unlocked by calling up AT&T and telling them I was going to Europe. My T-mobile SIM card is working just fine.
After a few hours of cussing, I managed to beat HardSPL 3.56 into my phone, because it already had SPL 3.56 on it.
Now I'm stuck trying to CID unlock and I can't seem to find a utility to work with it. The 'chain' of threads I followed dead ended saying downgrade to get it work, but I don't want to do that. I had a hard enough time getting HardSPL 3.56 to install. Then I ran across Jockyw's CID unlocker http://forum.xda-developers.com/showthread.php?p=1837147 and found myself saying ooo and ahh! But, it won't work with ANY 3.xx HardSPL.
Is there a CID unlocker compatible with 3.56??
I'd love to have AT command mode stuff and etc. from jockyw's, but at this point I think I'll take whatever I can get without needing to downgrade.
I can't seem to find it now, but didn't there used to be a list of pre-cooked ROMs here somewhere?
I think what I'm aiming at is a fully patched / hacked 6.1 HTC ROM with everything fixed and no bugs. Preferably minus any bloatware. If it has recommended utilities pre-installed great, if not, no big loss. Did they ever finish hacking a video driver together? I lost track of that thread, and can't seem to find any current info.
I've been waiting for a working Linux distro for a HTC device for years, but I'm going to throw in the towel and make the best of what I can get on windows. I've spent over $3000 on these HTC devices over the years, but don't rely on them because of all the bugs. Once I get my Tilt patched up, I'm jumping ship and trading in my old ones for a G1.
Thanks for any help!
p.s. I DO have to CID unlock before I can install any other ROMs.. right??
p.p.s. Here's all the details if it's any help:
rom version 3.57.502.2 WWE
rom date 7/17/08
radio version: 1.65.21.18
protocol version: 25.88.40.05H
tri-color screen
KAIS1*0
SPL-3.56.0000
CPLD-8
.
.
Serial
image version 3.57.502.2
R 1.65.21.18
G 25.88.40.05H
D 3.57.00.00
Note: This is BEFORE I updated to HardSPL 3.56
Thanks again!
Click to expand...
Click to collapse
I'm sorry to tell you that this:
KAIS1*0
SPL-3.56.0000
CPLD-8
Is not hard spl and if you pda has hard spl installed is will say this:
KAIS1*0
SPL-3.56.Hard
CPLD-8
I received my replacement Tilt 4 days ago from At&t and it came with WM6.1 and spl 3.56.0000 and you are right I cant find anything to change that spl. I have tried to CID UNlock and I get the white screen, so I tried jump spl 1.56 and 1.93 and neither one of them worked. So now I'm stuck with this 3.56.0000, I sent Jocky a PM and He told me that he was looking in to it and that he will get back to me. So I have to wait. Or maybe someone will read this that has a fix for this issue and help us.
I just bought my Tilt too, it also came with 3.56 and WM6.1 but I had NO problems unlocking and flashing hard SPL to it.
Now, what happens when you run Jump 1.93? and are you running it directly from your main memory NOT from a SD card, and no SD card is in the phone?
If you follow the directions EXACTLY it will work.
1 Run Jump SPL from your main memory
2 tri color boot screen saying jump 1.93 should show up, with USB at the bottom
3 Unplug your device wait 30 sec and plug it back in
4 In Active sync on your PC disable USB connections (I've actually flashed spl's without doing this)
5 Now run the customRUU with the hard spl file you want to upload.
BerettaFreak said:
I just bought my Tilt too, it also came with 3.56 and WM6.1 but I had NO problems unlocking and flashing hard SPL to it.
Now, what happens when you run Jump 1.93? and are you running it directly from your main memory NOT from a SD card, and no SD card is in the phone?
If you follow the directions EXACTLY it will work.
1 Run Jump SPL from your main memory
2 tri color boot screen saying jump 1.93 should show up, with USB at the bottom
3 Unplug your device wait 30 sec and plug it back in
4 In Active sync on your PC disable USB connections (I've actually flashed spl's without doing this)
5 Now run the customRUU with the hard spl file you want to upload.
Click to expand...
Click to collapse
Yes I did all that I'm very familar with the process this is my 5th tilt 2 of them the CID Unlock run just fine and the other 2 I that to run jump 1.56 to get pass the white screen. But for some reason I cant get anything to work on this tilt. I even try to install the OG WM6.0 to try to downgrade the spl but that did work either. Do you have any other suggestions?
IIRC for me to run the CID unlocker program I needed to flash the SPL first.
What is happening when you are trying to run the Jump SPL files? It's just not making sense.
You need to flash Hard SPL 3.29 BEFORE you try to run the unlocker, you can't do 3.56 then try to unlock it. Once its unlocked then flash it with hard 3.56 if you so desire.
Also after doing the 3.29 spl you need the proper cracked radio flashed to allow you to unlock the device, are you skipping that step?
It sounds like your trying to do an SPL upgrade and NOT SIM unlock the device since that step comes after.
BerettaFreak said:
Also after doing the 3.29 spl you need the proper cracked radio flashed to allow you to unlock the device, are you skipping that step?
It sounds like your trying to do an SPL upgrade and NOT SIM unlock the device since that step comes after.
Click to expand...
Click to collapse
No what I'm trying to do is CID Unlock my phone but is not working I get the white screen. I have tried everything I know to get pass it. I'm not trying to install hard spl 3.29 or 3.56. I have to CID Unlock my phone first right? That is what I've always done before. I'm out of ideas.
What is on your phone right now?
Factory SPL?
Factory 6.1 rom?
If so you need to run Oli's Sim Unlocker and CID Unlocker exe, this will FIRST flash a 3.29 hard SPL to your phone, THEN then next step is to flash a cracked radio and then you can sim and CID unlock your phone. As noted before tho a CID unlock is NOT necessary, if your Sim unlocked and Hard SPL'd you can do whatever you want to the phone.
BerettaFreak said:
What is on your phone right now?
Factory SPL?
Factory 6.1 rom?
If so you need to run Oli's Sim Unlocker and CID Unlocker exe, this will FIRST flash a 3.29 hard SPL to your phone, THEN then next step is to flash a cracked radio and then you can sim and CID unlock your phone. As noted before tho a CID unlock is NOT necessary, if your Sim unlocked and Hard SPL'd you can do whatever you want to the phone.
Click to expand...
Click to collapse
Thank you very much for all your help BerettaFreak you are the man!
Heeey! Did my thread get hijacked?
Lol, Ok where to start..
skr_xd:
If you DON'T need to CID unlock, then the Newb instructions are a bit confusing. Why does it say to install HardSPL, then CID unlock?
What or why would I need to CID unlock separately? ..or is it the Security unlock bit, Or SuperCID that I'm still missing? There must be some point to it, Because Oli's Does HardSPL then SIM unlock, THEN CID unlock.
Vol22002:
I DID get HardSPL 3.56 installed. I used JumpSPL 1.56. DO remember to yank out the SD and SIM card. Note the very bottom of my post says those stats listed are BEFORE I installed HardSPL.
I still need some more help with finding a ROM, but I suppose that would be best addressed in a new thread, so I'll do that.
Thanks again!
Crogon said:
Lol, Ok where to start..
skr_xd:
If you DON'T need to CID unlock, then the Newb instructions are a bit confusing. Why does it say to install HardSPL, then CID unlock?
Click to expand...
Click to collapse
CID Unlocking is done by installing the Hard SPL, the Hard SPL's don't check the Carrier ID (CID) when flashing new ROM's.
Crogon said:
What or why would I need to CID unlock separately? ..or is it the Security unlock bit, Or SuperCID that I'm still missing? There must be some point to it, Because Oli's Does HardSPL then SIM unlock, THEN CID unlock.
Click to expand...
Click to collapse
SuperCID Set's your CID to 11111111, Security unlock removes an extra check when Flashing Radios to avoid you getting stuck on some radios.
Crogon said:
Vol22002:
I DID get HardSPL 3.56 installed. I used JumpSPL 1.56. DO remember to yank out the SD and SIM card. Note the very bottom of my post says those stats listed are BEFORE I installed HardSPL.
I still need some more help with finding a ROM, but I suppose that would be best addressed in a new thread, so I'll do that.
Thanks again!
Click to expand...
Click to collapse
Just follow all the steps in the Guide by mskip and post and problems you have there. Understanding is not a pre-requisite, with that guide, you can figure out what all the steps do later...
Simply put:
HardSPL / CID Unlock / Super CID - Allows ROM's and Radio's to be flashed.
SIM Unlock - Allows you to use a foriegn SIM card
Security Unlock - Avoids problems when flashing some Radios.
Ta
Dave
DaveShaw said:
SuperCID Set's your CID to 11111111, Security unlock removes an extra check when Flashing Radios to avoid you getting stuck on some radios.
Security Unlock - Avoids problems when flashing some Radios.
Click to expand...
Click to collapse
Hey, thanks for the fast reply Dave!
Ok, So I COULD still Security unlock it, If I could find a security unlocker that worked with 3.56.
The bit about problems flashing radios sounds a bit like something that happens right before your phone becomes a brick. Could you point me to a resource about problem radios or how to avoid them?
I actually prefer to leave the radio alone, if I can get away with it. I just want a patched up ROM, as I mentioned earlier and in my new thread.
Anyway, If I end up needing to replace my radio, how do I avoid 'problem ones'. I understand that some radios simply don't work with some ROMs, but you seem to be eluding to something different here.
Thanks again!!
Crogon said:
Hey, thanks for the fast reply Dave!
Ok, So I COULD still Security unlock it, If I could find a security unlocker that worked with 3.56.
The bit about problems flashing radios sounds a bit like something that happens right before your phone becomes a brick. Could you point me to a resource about problem radios or how to avoid them?
I actually prefer to leave the radio alone, if I can get away with it. I just want a patched up ROM, as I mentioned earlier and in my new thread.
Anyway, If I end up needing to replace my radio, how do I avoid 'problem ones'. I understand that some radios simply don't work with some ROMs, but you seem to be eluding to something different here.
Thanks again!!
Click to expand...
Click to collapse
To Security Unlock, just follow this guide: http://forum.xda-developers.com/showthread.php?t=361236
Then upgrade to HardSPL 3.56 again.
Security Unlocking is done by setting a flag in the NAND. It's permanent (unless you re-lock) and there are no comptability problems once it is set (you need to use a special Hard SPL to set it first though).
EDIT:
There is no list of known bad radio's - only the "Radio from Hell" 1.65.17.10 - but another Radio from hell could appear any day
Ta
Dave
Thanks for clearing that up Dave.
I think I'm going to opt to ignore the security unlock, since it sounds like it's on an 'as needed' basis.
I have 'batter fish to fry' at the moment. I'm grinding gears trying to figure out HOW to figure out which ROMs I should be looking into, in my other thread.
By the by guys, I was joking about the 'hijacked thread' thing, I'm sure somebody will find the info useful.
Just when i though I had this all figured out and was about to Flash my first ROM.
I have read and re-read the flashing wikis and am still confused.
If your on WM6 then you need to use Jockyw2001's Kaiser SuperCID and Security Unlocker v0.1 right? But if you are on WM6.1 then you use Olipro's Kaiser SIM/CID Unlocker & Changer right?
Well I am currently on WM6 pro and dont want to upgrade to 6.1 just to use Olipro's program. So I would go with Jocky's right. Then people say you need to flash a HardSPL first before doing the SuperCID and Security Unlocker. But then in Jocky's directions it says Note that the security unlocker does not work with "SPL-3.28.Hard" and "SPL-3.29.Hard".
So what SPL do you start with.
And I know Dave already told me this earlier that since I have an AT&T Tilt and I am with AT&T service then I dont have to worry about SIM unlocking obviously. So can I skip the whole CID/SUPER CID/SECURITY UNLOCK routine. Can I just Flash HardSPL 3.29 or 3.56 and then start playing with ROMS till my hearts content or is all the security stuff really that neccessary?
So I am lost once again. Wow. I dont know why I am not getting this.
P.S. On another note, I am using AT&T Tilt with shipped ROM running WM6 pro. I have about 40-50 programs installed on it. When first setting up my phone I did the soft reset which supposedly gets rid of the bloatware. Anyways, with all my programs and it being the stock ROM I still have 62MB free PROGRAM RAM. I do however only have like 30MB Storage RAM. But 62MB of free PROGRAM RAM. I see people with naked ROMS that only get like 55MB of free PROGRAM RAM, is my phone like magic or something? Just curious as to how this may be possible.
asofiker said:
Just when i though I had this all figured out.
I have read and re-read the flashing wikis and am still confused.
If your on WM6 then you need to use Jockyw2001's Kaiser SuperCID and Security Unlocker v0.1 right? But if you are on WM6.1 then you use Olipro's Kaiser SIM/CID Unlocker & Changer right?
Well I am currently on WM6 pro and dont want to upgrade to 6.1 just to use Olipro's program. So I would go with Jocky's right. Then people say you need to flash a HardSPL first before doing the SuperCID and Security Unlocker. But then in Jocky's directions it says Note that the security unlocker does not work with "SPL-3.28.Hard" and "SPL-3.29.Hard".
So what SPL do you start with.
And I know Dave already told me this earlier that since I have an AT&T Tilt and I am with AT&T service then I dont have to worry about SIM unlocking obviously. So can I skip the whole CID/SUPER CID/SECURITY UNLOCK routine. Can I just Flash HardSPL 3.29 or 3.56 and then start playing with ROMS till my hearts content or is all the security stuff really that neccessary?
So I am lost once again. Wow. I dont know why I am not getting this.
Click to expand...
Click to collapse
There is a Hard SPL 1 by pof. Flash that first then follow Jocky's instructions.
Also the OliPro Security unlock isn't permenant, next time you flash a Radio it's gone.
Ta
Dave
Ok so Flash the Hard SPL 1 by pof
Then follow Jockys directions in using his Kaiser SuperCID and Security Unlocker v0.1
Then Flash either HardSPL 3.29 or 3.56. WHichever I choose?
Then go crazy with playing with different ROMS.
P.S. So every time you Flash a HardSPL it overwrites the previous one? Or do you have to get rid of a HardSPL first before putting a new one on?
asofiker said:
Ok so Flash the Hard SPL 1 by pof
Then follow Jockys directions in using his Kaiser SuperCID and Security Unlocker v0.1
Then Flash either HardSPL 3.29 or 3.56. WHichever I choose?
Then go crazy with playing with different ROMS.
P.S. So every time you Flash a HardSPL it overwrites the previous one? Or do you have to get rid of a HardSPL first before putting a new one on?
Click to expand...
Click to collapse
Flashing a new SPL overrides the old one.
You said before you were happy with WM6.0, if so use either the pof Hard SPL v1 or the jockyw Hard SPL v1.1 (Part of the security unlock); if you are using WM6.1, use one of the jockyw or cmonex Hard SPL 3.**. Using the wrong version won't break your phone, but Windows will randomly freeze.
Ta
Dave
Thanks again Dave for helpin me out and not tearing me a new one. But just one last question.
If I find a new ROM that I want to Flash and it uses WM6.1 then I have to make sure that I flash a HardSPL 3.xx before flashing that new ROM, is that what ur saying?