Hi everyone,
Last night my polaris started playing tricks on me. Basically the touch screen is not responsive but the hard buttons all work. For some reason though when I try to do a hard reset (GPS, Internet and reset) it doesn't perform a hardreset. Also I can't put it into boot loader mode
Any suggestions?
Can you try and flash a new ROM?
Yes i've flashed another cooked ROM and till nothing, even D/L official 6.1 ROM and still no touch screen.
I would immediately assume the touch screen is broken but the fact I can't use the hard reset combination (even though the individual buttons work) has got me confused
Hi!
I've the same issue.
This morning everything was fine but, now i can't use the touch screen.
It seems that the "cursors" is always in the upper right corner, but as i move it clicking in the other part of the screen it runs back in that corner.
I'm not able to hard reset, i've tried to do a clearstorage but i'm not able to enter the security code "1234" as i haven't the cotnroll of the screen
Have you solved this problem?
I will let you know shortly but cut a long story short it looks like i broke it
on closer inspection of can see a small dent/scratch on the screen so ordered a new touch screen off ebay. It arrived today so i'll be putting it in shortly so fingers crossed it was actually the problem. I figure the problem was the screen causing a permanent short and hence interupting my attempts at a hard reset
The screen cost about $35 AUD delivered and it took me about 30 minutes to pull the device apart, just have to see how long it takes to get it back together now
I'll post back soon
To me something similar has hapened.
Once i was changing the values of the pressure settings and the screen become unresponsive!
It was quite easy to fix it:
-just press the GPS button and the center button at the same time, then you will enter the menu were you can align the screen and, at the same time, the pressure registry values become as default.
Hope this helps with your problem, good luck with the screen replacement!
It's alive!!!!
Replaced the digitizer (touch screen) and all works again ...
Just to warn you though it isn't for the faint of heart, I thought i'd broke it a couple of times throughout the repair, next time i'll be getting a repair quote first
Congratulations!!
As my polaris is still under warranty i'll send my to the official assistance for the touch screen replacement!
Yesterday i've got my Cruise back from assistanza.. thay have replaced the whole mother board and now the touch screen is working
its a good idea to install my mobiler. this lets you control the device using a pc when the touch screen doesn't work. you can then back up your stuff before sending off for repair.
Related
OK, heres the deal..
Yesterday I managed to crack the bottom-left corner of my BA screen (damn medkit shifted onto it in my car glovebox ).
As i was checking to see how much of the screen was still responsive (seemed OK, still usable, only the 'New' button and the bottom item of the menu didnt work) the battery died (as in completely, hard reset died)..
So i plug in the power, and start the familiar initial setup. I get to the callibrate screen screen and am unable to continue..
So my question is: Is there any way to bypass the calibrate screen section of the initial setup? Im pretty sure enough of the screen still works for the device to function, if only i could get past this damned calibration screen..
Clearly i cannot bypass it completely, as the screen does need to be calibrated - but is there any way I can recover my BA?
Cheers All
Check out this thread:
http://forum.xda-developers.com/viewtopic.php?t=1910
or this one:
http://forum.xda-developers.com/viewtopic.php?t=6855
Also, if you can still see the image it means that only the digitizer (touch sensitive part) is broken, and not the screen so it shouldn't cost to much to replace.
And remember - search is your friend! :wink:
This might be a bit toooo late, but just in case some one is stuck with a broken screen as dabs and I were.
I received a k-jam (lucky me, it was for free) with a broken touch screen, it was left uncharged for a long time so after charging it, it entered the unwelcomed welcome mode (you know, align, copy, time zone ...) and there were no way of passing this part of initialization.
I had to do some search over the net, and I found a good article here ((Can I use a PDA that has a broken touch screen)) http://www.pocketpcmag.com/blogs/index.php?m=200510 which advised the use of "RemoteCalibration.exe" directly from the pc. This killed the welcome.exe program and I managed to re-use the K-jam again. The only draw back about this way is that I will have to connect the K-jam to a pc every time I hard reset, I hope there is a way to do the same action via mini sd cards.
After that, I installed fakecursor (but I'm looking for a better sw to emulate the touch screen function as this one cancels most hardware buttons on the devise) but at the moment, I'm using all the k-jam's functions.
Hope this would be of help to some one out there
All,
Im having some trouble trying to get the touchscreen to work properly..
I though it was a random bug with phone's the lock system [as i've never configured it nor used it before].. Several minutes after booting the touch screen would stop working, but all the bottons would work perfectly and respond on time..So i decided to flash the room..
Before flashing I did a hard reset [got hardspl], everything went ok until the calibration screen came up.. The first thing it asks you to do is tap it.. I have to tap it several tens of times and wait minutes [5-10] for it to respond.. I get to the white screen where the calibration cross appears, I tap it several times and wait some minutes but I guess the system thinks Im not taping in the right zone and just starts the process all over again..
I have no idea that's going on with the touch screen.. Can't use the phone at all..
Restore your handset to Stock SPL and Stock ROM
Return your device to HTC/Carrier for a replacement
unless of course the fault is your own, they shouldnt have too much of an issue with that
I live in Costa Rica.. They don't even sell HTC here, neverless a replacement and its oow anyways..
I think its related to the digitizer, i applied some pressure on the lower left side and it's working now, will most likely fail again though..
The other day, I hit the power button on my touch pro, and the screen didn't come on. I did a soft reset, and it started working again. Now today, the same thing is happening, but a soft reset isn't helping.
The screen's back light comes on, the LEDs on the buttons come on, and the phone seems to be working fine. I hear all the sounds, including the HTC sound while it is booting, and the new message sound, but the screen stays black. It still recognizes touches, it just doesn't show an image. I want to do a hard reset, and will if I can get it to come one one more time, but its been about a month since I backed up my contact list. Lesson learnt there. I'm afraid it might be a hardware problem since I don't see anything while its booting either.
Anyone know if this is a known hardware issue with the touch pro? The phone is less then 3 months old, and I've been real careful with it. I haven't dropped it from more then 2 feet, and even that was onto carpet. Its the Verizon version if that makes a difference, and I'm running one of the NFSFAN roms. Its not the newest one, but rather the one posted on October 19th. I doubt its the rom, though, as I've been using it for around 2 months with no issues.
EDIT: Ok, I went into the bootloader to see if it was hardware of software. I figured if it was hardware, the screen would be black, and if it was software, it would be the rainbow. Sure enough, the screen stayed black. Hit the reset button, and the screen actually came on! Go figure. Went to do a backup, and the screen literally crapped out on me while I was watching it. Definitely a hardware problem.
similar with Touch HD... kinda
I've been having a similar problem with my Touch HD. The problem is very intermittent though and is sometimes hard to reproduce. The screen and phone will be working fine then once in a while when I push the power button to lock the phone, I'll unlock it and the screen stays black. I know that the phone is still on and even unlocked because pushing the buttons at the bottom makes the phone vibrate. The only consistency in reproducing the problem happens after I do something major on the phone such as making a phone call, browsing the internet, sometimes charging the phone. Other than that, I can sit here and push the power button all day and it'll come on and off with no problems. When the screen does go black I've taken the battery out repeatedly as well as repeatedly rebooted the phone until it comes back on. I've tried doing hard and soft resets to no avail. I've tried deactivating "turn off backlight if device is not used for" and "turn off device if not used for" without any resolve. After this I've even left the screen on (disabled backlight off) to see if it flickers or shows any sign of being faulty and it seems to be fine. I'm currently on Dutty's HD WM 6.5 Leo R5 WWE rom, but this has happened with two other roms (NRG, LIA). Other info include:
OS: 5.2.23016
Manila: 2.519192828.0
Radio: 1.14.25.24
Protocol: 52.64.25.34H
I guess the only consistent software has been my radio. Please help! Any advice would be awesome. I've tried google search and xda search without much help. Thanks
One of my phones is an HTC Surround that i don't use that often but still want it to work. To the issue though, each time the phone is turned on (not powered on, just woken) the screen refuses to work on the right side. In order to get past the lock screen you have to swipe up on the left side. After that the right screen becomes 'active' only after you swipe the left screen again. The home button and the search button on the phone only work after sliding the left side of the screen down and hitting the back button, once that task is accomplished the entire phone works perfectly and no more issues develop. This has been driving me crazy trying to figure out why its doing this. I reset the phone twice, both through the reset in the settings and doing a hard reset. When neither of those attempts worked i put it in bootloader and flashed this release (http://www.filefactory.com/file/b48...S_1.03.502.07_5.51.09.06_22.30.50_RELEASE.exe) to it and it still continues with this wierd touch screen issue.
I could probably just throw the phone away and not care but i'd prefer to fix it and sell it. Plus its driving me insane trying to figure out the issue.
(apologies for the wall of text http://incredibly.ytmnd.com/)
Hi guys
I have this strange behavior going on in my Sentation.
Out of nowhere my phone started to have strange screen behavior... Didn't light up after pressing the power button (had to phone my self in order to get screen on).
The next thing was that suddenly the screen goes to maximum brightness or goes to minimum without any explanation (tried both auto brightness or manual).
After that I noticed that the screen went off when I was using it but when I pressed the left side of it it lighted up and off again... making me think of some kind of bad contact underneath. As I already had changed a broken touch screen for t3 times, and let the phone fall for several times I thought it had to do with some plug out of line...
I disassembled the phone completely and mounted up back again. The thing is that the phone started to freeze every 5 minutes (screen on but completely freezed. I have to pul out battery). Sometimes it freezes even in the recovery menu. I've tried several rom's with full wipe and not installing anything and its all the same.
Some times I still not that the screen goes off during the freeze but when I touch the left side it goes on again, but that doesn't change the freezed state even that I let down the phone for several minutes.
I disassemble the phone again, tried different back cover and different battery (one stock and other extra strength) I tried also all the suggestion related to the small pin in the back not connecting well with the back cover (adding an aluminium foil, pulling the pin out, etc..)
Nothing seams to resolve anything so I have clearly an hardware problem... but I don't know what to replace or where to look the damage!!!
Can anybody help me please?!
Update
I have an update on my problem:
I noticed that when I leave the phone on top of some kind of metal part and don't touch it it works all day without any problem but, as soon as I start to touch the phone, it freezes within minutes!
Could it be some kind of static electrical problem? How to resolve it?
I would apreciate any help
Thanks