After I tried to upgrade the rom to WM6, my JAMin got stuck at bootloader. After that, I tried to flash WM5 roms without success and suddenly (after a reset) the screen became white with some horizontal and vertical lines constantly moving. I discovered that it was only the screen that was garbled as it still connected to PC, so I installed (without seeing anything on my JAMin) the NVID ROM trying to restore it. It installed sucessfully, but the screen remained garbled with the white background and random lines. I know it was sucessfully installed because I heard the typical "welcome" sound before configuration.
Do you know any way to restore the screen? Or must I send it to I-Mate to repair?
You can try and reattach the screen cable to the rest of the device, but this will boid any warranty you have, and may damage your device further. If the device is under warranty, I would suggest flashing the ROM the device came with (unfortunately the FTP server is down at the moment, so it might take some fishing around for) and sending the device back to get repaired properly.
mpmf said:
After I tried to upgrade the rom to WM6, my JAMin got stuck at bootloader. After that, I tried to flash WM5 roms without success and suddenly (after a reset) the screen became white with some horizontal and vertical lines constantly moving. I discovered that it was only the screen that was garbled as it still connected to PC, so I installed (without seeing anything on my JAMin) the NVID ROM trying to restore it. It installed sucessfully, but the screen remained garbled with the white background and random lines. I know it was sucessfully installed because I heard the typical "welcome" sound before configuration.
Do you know any way to restore the screen? Or must I send it to I-Mate to repair?
Click to expand...
Click to collapse
Hi frd,
I have exactly the same problem!
Nothing , only the f*** white screen!
I can browse the device via active sync, can rcv calls but the white screen.
I have checked the ribbon connector of the LCD and make reflashing some ROMs but nothing.
I still wondering is it hardware or software problem!
Please let me know if you have progress!
Thanks
G.
Try to replace LCD module, I think thats right way.
It will be a hard ware problem. Probably the ribbon cable as the screen is showing something so it must be working at least a bit.
Hello,
i have the same Problem with my QTEK S200.
First i changed the Rom and it worked perfectly for two days.
Then i had to change my Sim card and after that the problem came again.
I tryed a lot of times to reflash the rom but the problem persist.
How can it be that it worked again for some days ?!
is it the touchscreen of the lcd unit i have to replace ?
is it possible to do it by my self ?
thanks for your help !
Hi everyone.
I had a similar problem an hour ago (Qtek S200 G3):
I Upgraded to a 6.1 rom and then to another, after that my device was stuck in bootloader(3 colour screen). Any 6.1 rom that I tried would install, but after installation device always boot in to the 3 colour screen.
I tried this original shipped rom http://files.mail.ru/HZUAH1 (it's WorldWidwEnglish) (to download just click the link "скачать" or the file name RUU_Prophet_220734_2207114_024721_QtekWWE_Ship.exe
) and it installed!!! It TAKES A WHILE TO INSTALL!!! But it worked!!!
May want to try it.
Hope this helps.
hello,
picture on screen was immediatly clean again ( bootload image ).
it was impossible to change the rom because i have a G4 model.
i flashed the rom with another french rom for G4 and it worked perfekt.
now i tried to remove the battery again for 3 seconds and now i have the same problem again. really strange ....
i tryed the same procedure again but no success.
I reinstalled differents rom's again starting always installation from bootloader.
After about 10 new installations i've clean picture again.
now i'll not put off, restart, or take of battery till one of you know what's the problem.
Thank you for your help !!
are you guys sure its not an intermitant hardware problem, it sounds like it to me. if yu were able to get a clean picture for a short time and now its white again, it cannot be the rom? As for replacing it, nothing is impossible and there is always ebay and google
QTEK S200 G4 CID unlock
How can I CID unlock a device that need´s that to upgrade the Rom?
Is there already any program that , Lockwiz dont do the job, can performe the unlock?
Thank you.
For G4 CID unlocking, you need to user Hard/Soft SPL.
same problem
my imate jamin got the same problem. it happens only and only when I remove the battery and when I leave it to charge for 1-2 days the LCD works again and show clear pic. any suggestion? activesync and &... are all ok!
Well, i upgraded to windows Mobile 6, but haven't removed the batterie anymore.
But i'm able to put it off now, what was impossible before.
Related
Hello friends, this is my first post in prophet forum, though I had been a ppc user for more than 2 years. 5 months back, I bought an O2 XDA Neo, which was loaded with a dopod rom, with numbers coming up as 2.09.001 etc during startup. Shortly after purchase, I flashed with RUU_Prophet_220734_2207114_024721_QtekWWE_Ship rom. Everything went on well, and I was using the phone without problems for the past 2 - 3 months. Well not exactly without problems, some times when I reset the phone, it gets stuck at the spl, ipl screen, and I have to reset again many times to get it to load windows. I initially thought the problem may be due to the battery not being charged fully, but later I found that battery charge is not the problem, as the phone not booting became more and more common even with a fully charged battery. Even when I managed to get the phone started after repeated and frustrating soft resets, I started to get corrupt PIM data, like the contacts and calendar applications not starting up. ALso strange folders with name y? and y?? appeared in the phone memory. THese folders could be deleted only with Resco Explorer. Also the bluetooth was not working properly, that is when I turn it on using the comm manager, the blue tooth icon gets activated but actually no bluetooth is turned on. Later after a soft reset, bluetooth turns on but now the icon in comm manager is not activated. I did a hard reset a couple of times thinking that this problem will be rectified, but all the problems continued.
Going through the forum i read some where that JAMin_WWE_213923_2139123_022021_ship was one of the most stable roms for this phone, so I set about flashing this rom. I used ROMUpdateUtility-NoVendorID and the update went on till 95 % when it showed error 326. I tried again, with the same result. I later flashed RUU_Prophet_220734_2207114_024721_QtekWWE_Ship back, and the phone is working as before.
NOw I would like to get the following problems corrected
1. Phone getting stuck at ipl, spl, gsm screen
2. Proper working of bluetooth as I would like to use it with my BLueant Supertooth II
WHat will be the correct these prolems ? will the imate rom correct these problems, if so how am I to go about loading it ? or is there a better one than what I am having now ? or is it a HARDWARE problem ?
I am very sorry for this extremely long post, but I felt if I said all my problems in one post, I would get better response.
PLease help....
You should have stayed with the RUU_Prophet_220734_2207114_024721_QtekWWE_Ship ROM from the beginning, since it's the best and also latest official Prophet ROM. It's a 2.20 ROM which is the latest available.
GAMBIT999 said:
You should have stayed with the RUU_Prophet_220734_2207114_024721_QtekWWE_Ship ROM from the beginning, since it's the best and also latest official Prophet ROM. It's a 2.20 ROM which is the latest available.
Click to expand...
Click to collapse
I am still with that ROM. It is with this ROM that my prophet is causing the above problems.
Can you guys advice me how to load JAMin_WWE_213923_2139123_022021_ship rom with out this error 326 showing up ?
It may be that my q-tek is bricked. To cut a long story short I am rebooting and it is getting stuck on the QTEK page displaying:
IPL 2.20.0001
SPL 2.20.0001
GSM 02.47.21
It also had OS2.20.7.34 but this is not showing.
Problem is - this is a swisscom fone and therefore I cannot access the original QTEK site as it fails to recongise my IMEI.
I have also tried in my ignorance to reflash it but now its stuck.
Is there anyway I can have access to the original English software so that I can try to reflash and re-install from scratch?
I also wanted to add that even a hard reset is not getting it to start up.
And another thing - sometimes the screen just freezes and breaks up in line and colours. What is that? Is my fone dead or dying?
Any help will be appreciated.
Delgada
The three colour screen is bootloader. If you can get that, your device is recoverable.
edit: http://wiki.xda-developers.com/index.php?pagename=Prophet_recovery
This does work, I wrote it from past experience....
Hi,
thanks for your help. Did all your link said.
IT LIVES AGAIN!!!!! THANKS
One question though - if my fone still goes off and the screen feezes and fades out or breaks into lines - what sort of problem would that be?
Cheer!
Delgada
Depends... It could be the ROM, it could be the ribbon cable connecting the screen to the motherboard, it could be an IC (but I doubt that as you say it works)...
Hi.
I realised that last time i opened my Qtek something must have not been in place as I was pressing the case and the pda was freezing. I opened it up for the umpteenth time and made sure all contacts were ok and closed it carefully. It now works fine. Last hiccup - getting it to read my home wifi when it reads everyone elses already.
Thanks
Delgada
Hello,
I have a few problems with my Touch Pro.
First off it's keep saying that there is a headset connected i've tried to clean the connector's soft- hardreset but with out any luck, also searched the internet but no one has a solution even a reg fix would be great but can't find anything on it.
So i want to send it to HTC because i still have waranty but...
The second problem is that the boot screen is changed some how, it shows a kind of BIOS screen like a PC when booting up, the other problem is that i can't find the stock Dutch ROM for the TP which i need for the waranty it had a dutch rom on it when i bought it.
If anyone could help i it would be great
greetings ruudjuhnl
Hy,
I ve got the problem that suddenly my TP shows unusually hanging after a few minutes playing around. If i do a softreset then it hangs on the splash screen and nothing happens. I can do a hr then and the same story begins. After tast appeared i flashed some other roms to be sure that its not depending from the rom. Also i restored different backups, with all its the same... i fear that a part of the memory is defect ... Any ideas how to test the memory or other suggestions? thx in advance.... i dont want to use my microwave
Greetz
Boris
Did this happen suddenly or did you do something before it happened (eg install something, etc)?
Mine just today won't turn on, I had it off all day and now it just sits on the splash screen.
Trying some things, if I figure anything out I'll let you know.
No, i didnt do anything special today or yesterday, but a week ago i set it up completly new, cause i had equal problems.... to set it up completly new with all progs and cosmetic "operations" costs me nearly one week so i dont want to do it again ...
If i find a way to solve, i will post here too
Greetz
Boris
I flashed EnergyROM (booted into the tricolor screen by holding down Power and Volume Down), and it seems to be working.
Youre the lucky one, congrats...
I have a similar problem. The only change/new install is the updated version of Microsoft MyPhone. Now my TP will not connect to my telephone provider: T-Mobile. It just tries and tries but never connects.
Also, sometimes when I try to open any program, I get the error message that the certificate cannot be read. a soft reset fixes this but this problem is driving me crazy.
Is this another Microsoft update ****up?
same here: today more than 3 times problems with certificate or similar message ... thinking of the last timebomb in my old romeos rom ... was no fun..
Borisku,
Are you running Microsoft MyPhone? If so, did you do the software update within the past 4 days?
i do, but i didnt update ... ??? This morning my TP hung again, and i tried to sr it.... seemed to work until tp vibrates 3 times and then nothing anymore, no screen, no button, nothing
.... took out battery, left it out for 30 minutes, then i could HR again and restore my backup... since then no problems.... do you think it could run too long, getting too hot or something like this??
Greetz
Boris..
Edit: was too fast just 1 minute after i wrote that, tp hangs while in connection to active sync.... hr now, will test how it runs with pure romeos2 for 2 days now... rport follows
Edit II: The last days i always flashed from SD Card... i will now try to flash ROMEoS2 from PC ... maybe theres a difference, especially cause the text at the end of flashing from SD was confused. there were mor than one words at one place one the screen, and i found i typing on the screen RaphSimg.nbh, although the file is named as usual raphimg.nbh (without the "s" in the centre...)
I hope i m not too early: i think i solved the prob, maybe that helps somebody & prevents a tp from ending in a microwave
in preparing to bury my tp in the microwave i flashed back to the german stock rom or - correct - to the official update that can be loaded from the HTC Homepage; it contains not only the Rom but also radio & Splash Screen. I flashed it to my tp and was prepared to undo Hard SPL, but it gave it a chance.... and it ran like a VW beetle, flashed back to ROMeOS2, it runs.... i will wait till tomorrow & hope that it will not change to freeze or change clock Font colour partly as it did before...
Hope it will help somebody...
Greetz
Boris
Edit: its now 14th of december and it runs like a charm... seems like the failure is gone through flashing to stock ROM & then flashing ROMeOS again
Still is okay ...
I have been having this error where the phone prevents itself from booting, showing a screen that tells you to connect to PC , for a while. Only way to fix it is to remove the battery and restart but that is just a temporary fix. What exactly is this? What causes it? Is it a software issue or a hardware issue? Should I get an exchange or do you guys think this will be fixed with the next update?
Thanks
Never seen that error message. I'd say reset once, if you see it again, get it exchanged.
Yea this my 4th HD7 it shows the error code when you plug it to the PC in zune. Funny thing is that I owned a speck case and I reboot the phone in the case till then. This time i pulled the battery out, put it back in and powered the phone on without the case and it is working fine. I guess the case is pushing down a button or sth and that prevents the phone from working properly. Very weird..
Hey there! I've been having the same error! This is my 2nd HD7, I own the Speck case and I do not think its the case. This issue is happening on mine with or without the case. Pulling out the battery just doesn't cut it. I have to:
1. Remove the battery
2. Plug the USB Charger
3. Insert the battery back
4. Turn on.
I love the phone but this is really frustrating!
Edit: Too bad I can't post the link to youtube due to member status. But the video is up just search for it "c101002e"
Just happened to me too. First day using the Speck case too and i let the battery drain till it died and upon reboot it showed the 'plug into computer' screen. Hope it is just the case causing problems.
did you all updated the sd card ?
you could try to reflash this rom (if you are on t-mobile USA ) http://forum.xda-developers.com/showthread.php?t=810346
Take this one "RUU_Schubert_TMOUS_1.20.531.01_Radio_5.51.09.11a_2 2.31.50.09_Signed_SCHUBERT_RELEASE"
its just the stock tmous rom .
Weird coincidence that all of y'all are using the same case. Maybe it is damaging on of the buttons?
nrfitchett4 said:
Weird coincidence that all of y'all are using the same case. Maybe it is damaging on of the buttons?
Click to expand...
Click to collapse
somewhere on the board they did tell that this case make the buttons really sensitive and it make the phone unusable .
theres a thread on tmobiles forums talking about the same issue, and most if not all the people there have the speck case. Someone says they tested it with and without the case and came to conclusion that the case is putting too much pressure on the camera button, which seems to be causing the problem.
would post the link to the other forum but i cant find it lol
pierce_m said:
theres a thread on tmobiles forums talking about the same issue, and most if not all the people there have the speck case. Someone says they tested it with and without the case and came to conclusion that the case is putting too much pressure on the camera button, which seems to be causing the problem.
would post the link to the other forum but i cant find it lol
Click to expand...
Click to collapse
Yea that was pretty much what was happening to mine. Although I remember trying to boot it without the case and having the same error before so what I did that I did a hard reset ( press power and both volume buttons at the same time) then when the phone booted, I rebooted it without the case immediately and its been working no problem since. I am pretty sure that case pushes the camera button since it grips the phone very tightly. I even overloaded the ram by opening lots of apps that runs in the background and then rebooted but it is working perfectly fine as of right now. Weird.. I am guessing its just a weird bug not a hardware defect.
I found it in a post in the mozart forums, so i tried it, as you do, cause its something new to play with cause my TP2 didnt like swimming, but anyway it was something about hoding down the camera button while power on, and it brought up a picture of a phone and cable and instructing you to plug it into a pc and when i did it started Zune and something about restoration error, so like in the previous posts it may be a stuck or faulty button somewhere on the phone that is causing it.
i didnt watch the video so if that had it in it never mind
cheers
Today 11 April 2011 I got notification about NoDo update for my phone.
It is HTC Mozart on Orange France network.
The pre-NoDo update was istalled about 20 days before.
The update got stuck at step 8. It seemed I had an unusable phone. In a periodic reboot mode into the update screen.
I checked on my W7 64 bit laptop the relevant backup folder, where all my phone data was supposed to have gotten backed up during the update. The folder was empty.
I therefore realized my phone got its rom corrupted during the update and I could not get back my pre-NoDo backup, since this latter was missing from my laptop.
Zune was on no help, stating a C101002E error.
The Windows Phone Support Tool was also of no use, reporting an error code while trying to restore my data.
XDA-forum provided me with a solution:
I went here
http://forum.xda-developers.com/showthread.php?t=1000781
and downloaded both bootloaders with relative roms.
After getting into the bootloader screen (red, green and blue screen), I installed the first ROM provided by Ansar. This could not install succesfully.
With the bootloader tool I could nevertheless confirm my idea I did not have anymore a functioning rom into my phone.
The second rom, the one ending with "Signed_by_ansar" could be succesfully installed.
I now have a Mozart fully functioning.
I had to restore my windows live account, Gmail, etc. My apps did not come back up after syncing with Zune.
I realized I just lost all my SMSs and home screen settings.
My phone was originally network unlocked and remained as such.
I got a notification that there is an official update for my phone the first time I rebooted. I will wait before attempting this update. The ROM by Ansar has got anyway copy/paste, being a NoDo ROM.
The ROM from Ansar, although for Orange France, removes the Orange splash screen when the phone starts. I guess if I need to use warranty on this phone right now I may have some issues with Orange France. Maybe when I update the phone following the update notification I got, I will re-establish a fully certified Orange ROM.
i9o pls and any one pls help me , i faced problem with [260] connection problem between my hd7 and pc vista 64 bit, actually i followed to steps in forum (error code C101002E) and drivers were installed (htc usb sync) before i started to flash rom NoDo bootloader 1, But no way still the problem [260]. i also tried another RUU htc asia xxx707xxx. because i have spl 1.23.2250.0(112138).also some links of RUU to download signed by ansar disappeared in rapid and other sourses, pls help to solve connection problem
Microsoft has release the Windows Phone Support Tool to fix this problem: http://support.microsoft.com/kb/2530409
WPS doesnt help in my case, Im malaysian and thought that need Asia RUU, but when i tried Europian RUU it nicely works, maybe because of i have 8G phone. the RRU is RUU_Schubert_HTC_Europe_1.69.401.01_Radio_5.54.09.21_22.33b.50.10_Signed_SCHUBERT_RELEASE(2)
day2die said:
Microsoft has release the Windows Phone Support Tool to fix this problem: http://support.microsoft.com/kb/2530409
Click to expand...
Click to collapse
Do you know what this tool does to the computer?
I would try it but honestly don't want to do it before I have info what it does to my PC settings. Unfortunately MS doesn't share with this knowledge.
Hi everyone!
I have a big problem with my new hd7.
Just bought, and wired for the very first charging but the phone continues to restart by itself.
Tried a hard reset, to set it in download mode and fix with Windows Phone Support Tool but still nothing to do. Even tried to install a new ROM but at the first start it continues with its loop.
In download mode zune tried to upgrade to nodo but it shows the error C101002E.
Don't know what else to do. Any idea? It's new!
MusicMan587 said:
Hi everyone!
I have a big problem with my new hd7.
Just bought, and wired for the very first charging but the phone continues to restart by itself.
Tried a hard reset, to set it in download mode and fix with Windows Phone Support Tool but still nothing to do. Even tried to install a new ROM but at the first start it continues with its loop.
In download mode zune tried to upgrade to nodo but it shows the error C101002E.
Don't know what else to do. Any idea? It's new!
Click to expand...
Click to collapse
No one had this problem? am i the only unlucky on the earth!?
Return for warranty replacement. Your phone is broken.
Thank you...i hoped i could solve it to not to wait september to have my phone back.