Hello friends, this is my first post in prophet forum, though I had been a ppc user for more than 2 years. 5 months back, I bought an O2 XDA Neo, which was loaded with a dopod rom, with numbers coming up as 2.09.001 etc during startup. Shortly after purchase, I flashed with RUU_Prophet_220734_2207114_024721_QtekWWE_Ship rom. Everything went on well, and I was using the phone without problems for the past 2 - 3 months. Well not exactly without problems, some times when I reset the phone, it gets stuck at the spl, ipl screen, and I have to reset again many times to get it to load windows. I initially thought the problem may be due to the battery not being charged fully, but later I found that battery charge is not the problem, as the phone not booting became more and more common even with a fully charged battery. Even when I managed to get the phone started after repeated and frustrating soft resets, I started to get corrupt PIM data, like the contacts and calendar applications not starting up. ALso strange folders with name y? and y?? appeared in the phone memory. THese folders could be deleted only with Resco Explorer. Also the bluetooth was not working properly, that is when I turn it on using the comm manager, the blue tooth icon gets activated but actually no bluetooth is turned on. Later after a soft reset, bluetooth turns on but now the icon in comm manager is not activated. I did a hard reset a couple of times thinking that this problem will be rectified, but all the problems continued.
Going through the forum i read some where that JAMin_WWE_213923_2139123_022021_ship was one of the most stable roms for this phone, so I set about flashing this rom. I used ROMUpdateUtility-NoVendorID and the update went on till 95 % when it showed error 326. I tried again, with the same result. I later flashed RUU_Prophet_220734_2207114_024721_QtekWWE_Ship back, and the phone is working as before.
NOw I would like to get the following problems corrected
1. Phone getting stuck at ipl, spl, gsm screen
2. Proper working of bluetooth as I would like to use it with my BLueant Supertooth II
WHat will be the correct these prolems ? will the imate rom correct these problems, if so how am I to go about loading it ? or is there a better one than what I am having now ? or is it a HARDWARE problem ?
I am very sorry for this extremely long post, but I felt if I said all my problems in one post, I would get better response.
PLease help....
You should have stayed with the RUU_Prophet_220734_2207114_024721_QtekWWE_Ship ROM from the beginning, since it's the best and also latest official Prophet ROM. It's a 2.20 ROM which is the latest available.
GAMBIT999 said:
You should have stayed with the RUU_Prophet_220734_2207114_024721_QtekWWE_Ship ROM from the beginning, since it's the best and also latest official Prophet ROM. It's a 2.20 ROM which is the latest available.
Click to expand...
Click to collapse
I am still with that ROM. It is with this ROM that my prophet is causing the above problems.
Can you guys advice me how to load JAMin_WWE_213923_2139123_022021_ship rom with out this error 326 showing up ?
Related
I've been running a ROM I built from the consolidated kitchen this weekend without any problems. Today I updated the radio to 2.69.11 from the cingular 2.25.11. After the flash the phone froze on the windows mobile screen. After some time I tried to reset the phone and it froze again, a few more tries and it finally boots up. I didn't pull the memory card when I flashed and thought that might have been the problem so I flashed again even though the phone was showing 2.69.11. I don't remember everything after that but it wouldn't boot up and I have tried flashing the original Cingluar ROM & T-mobil 2.26 without any luck.
The phone is stuck in bootloader now and is getting a error code 302 I think it's because the phone doesn't stay on when the USB cable is attached. It gets to about 15% and the phone resets and the error 302 pops up. When connected and not trying to update the phone turns on and off in the bootloader screen. I have pulled the battery, rebooted the laptop, tried using mtty,and pulled the sim. I thought the original problem might have been because I flashed at 52% battery. I put a older battery in after that appeared to have a good charge. Right now I put the phone on charge with the newer battery to see if this helps. I am not sure if it is charging because the orange light is not on, I can't get the phone to stay turned off when plugged into the charger and the bootloader screen is on.
And yes I have been searching for hours for a solution to this problem.
Also looking for a post I read about doing a master reset, I have tried holding the 2 soft keys when turning on, didn't help.
I think this says it all I have tried everything, does anyone anything else to try?
Thanks
UPDATE: went out for a few beers and some food. Not sure it the battery charged (bootloader screen on the whole time it was plugged into the charger)
Tried flashing again with cingular ROM, got about 20% and phone shut off and turned on again in bootloader. Flash gave 302 error again. Tried again and phone reset (on and off) every 5 seconds when connected to laptop with USB.
I'm hopping someone out there has a answer for this problem.
Back from the dead HALLAULA!!!!
This morning I spent more hours searching still didn't out find anything.
I tried mtty again and noticed that I never got to the screen that shows USB>
to enter the command "set 14 0"
I came up with a thought and this is what I did. Created a new ROM, OS only. Thinking it will load faster than any other ROM. It reached 100% in 3 minuets the whole I'm coaching come on baby don't restart and than going (don't know how to explain the feeling) waiting the next 2 minuets to get to finished. But it got there booted fine. I don't know why it stayed on this time and didn't restart, maybe having the battery out all night had something to do with it. After I flashed the Cingular ROM than the original I created and lastly Radio 2.69.11
I hope this helps someone in the future,
i need your help
hi man I had a prophet s200 and give me the same error 302 but, with the diference in my case got 98% adn then stuck in boot screem, please help me if you can...and sorry for my english
Guys,
It may help checking out this thread!
http://forum.xda-developers.com/showthread.php?t=294107
Can you help me out?
How did you create a new ROM - OS only? I'm having the same problem..can you walk me through this?
Thanks
How did you create another ROM (Operating System only)? I'm having the same problem and I have tried for the past 2 weeks - but no luck. Can you walk me through it?
Thanks
I used the consolidated kitchen (sticky at the top of this forum)
Uncheck everything on Build OS.
My problems started from a version of battery status that caused the original problem and not having enough of a charge on my battery.
Make sure you are CID unlocked (if you have a G3) and your battery is charged.
Umm, you can't uncheck everything in build OS or you will have problems, especially if you don't check a tuchflo or non touch flo dll or choose a commanager and probably a few others things. I don't have build OS up in front of me to check. The whole point to this msg is that you can check everything in build OS (besides the ones that say choose only 1) and it will build an OS only rom for you. That's the whole point behind build OS.
You are correct, I was kind of going from memory since I had built the striped down ROM awhile ago.
After I tried to upgrade the rom to WM6, my JAMin got stuck at bootloader. After that, I tried to flash WM5 roms without success and suddenly (after a reset) the screen became white with some horizontal and vertical lines constantly moving. I discovered that it was only the screen that was garbled as it still connected to PC, so I installed (without seeing anything on my JAMin) the NVID ROM trying to restore it. It installed sucessfully, but the screen remained garbled with the white background and random lines. I know it was sucessfully installed because I heard the typical "welcome" sound before configuration.
Do you know any way to restore the screen? Or must I send it to I-Mate to repair?
You can try and reattach the screen cable to the rest of the device, but this will boid any warranty you have, and may damage your device further. If the device is under warranty, I would suggest flashing the ROM the device came with (unfortunately the FTP server is down at the moment, so it might take some fishing around for) and sending the device back to get repaired properly.
mpmf said:
After I tried to upgrade the rom to WM6, my JAMin got stuck at bootloader. After that, I tried to flash WM5 roms without success and suddenly (after a reset) the screen became white with some horizontal and vertical lines constantly moving. I discovered that it was only the screen that was garbled as it still connected to PC, so I installed (without seeing anything on my JAMin) the NVID ROM trying to restore it. It installed sucessfully, but the screen remained garbled with the white background and random lines. I know it was sucessfully installed because I heard the typical "welcome" sound before configuration.
Do you know any way to restore the screen? Or must I send it to I-Mate to repair?
Click to expand...
Click to collapse
Hi frd,
I have exactly the same problem!
Nothing , only the f*** white screen!
I can browse the device via active sync, can rcv calls but the white screen.
I have checked the ribbon connector of the LCD and make reflashing some ROMs but nothing.
I still wondering is it hardware or software problem!
Please let me know if you have progress!
Thanks
G.
Try to replace LCD module, I think thats right way.
It will be a hard ware problem. Probably the ribbon cable as the screen is showing something so it must be working at least a bit.
Hello,
i have the same Problem with my QTEK S200.
First i changed the Rom and it worked perfectly for two days.
Then i had to change my Sim card and after that the problem came again.
I tryed a lot of times to reflash the rom but the problem persist.
How can it be that it worked again for some days ?!
is it the touchscreen of the lcd unit i have to replace ?
is it possible to do it by my self ?
thanks for your help !
Hi everyone.
I had a similar problem an hour ago (Qtek S200 G3):
I Upgraded to a 6.1 rom and then to another, after that my device was stuck in bootloader(3 colour screen). Any 6.1 rom that I tried would install, but after installation device always boot in to the 3 colour screen.
I tried this original shipped rom http://files.mail.ru/HZUAH1 (it's WorldWidwEnglish) (to download just click the link "скачать" or the file name RUU_Prophet_220734_2207114_024721_QtekWWE_Ship.exe
) and it installed!!! It TAKES A WHILE TO INSTALL!!! But it worked!!!
May want to try it.
Hope this helps.
hello,
picture on screen was immediatly clean again ( bootload image ).
it was impossible to change the rom because i have a G4 model.
i flashed the rom with another french rom for G4 and it worked perfekt.
now i tried to remove the battery again for 3 seconds and now i have the same problem again. really strange ....
i tryed the same procedure again but no success.
I reinstalled differents rom's again starting always installation from bootloader.
After about 10 new installations i've clean picture again.
now i'll not put off, restart, or take of battery till one of you know what's the problem.
Thank you for your help !!
are you guys sure its not an intermitant hardware problem, it sounds like it to me. if yu were able to get a clean picture for a short time and now its white again, it cannot be the rom? As for replacing it, nothing is impossible and there is always ebay and google
QTEK S200 G4 CID unlock
How can I CID unlock a device that need´s that to upgrade the Rom?
Is there already any program that , Lockwiz dont do the job, can performe the unlock?
Thank you.
For G4 CID unlocking, you need to user Hard/Soft SPL.
same problem
my imate jamin got the same problem. it happens only and only when I remove the battery and when I leave it to charge for 1-2 days the LCD works again and show clear pic. any suggestion? activesync and &... are all ok!
Well, i upgraded to windows Mobile 6, but haven't removed the batterie anymore.
But i'm able to put it off now, what was impossible before.
Hello all,
A simple question.
How can one tell what kind of a unit he has, is it WWE or is it ASIA or maybe another, I have bought my unit 2nd hand and since then had problems with the softwares and radio roms.
I have used WWE rom, and I just can not get all my contacts in, I have used ASIA and for a few days all was working fine, till something happens I reset the unit and either data is lost or the radio has no signal etc.
Another question, is it possible to stop the Automatic Customization after a hard reset???
Your help would be much appreciated.
WWE or Asia depends on installed ROM. Type can be Polaris 100 or Polaris 200, AFAIK, and is visible during hard reset.
What ROM are you using now? Looks like trouble with ROM or bad device.
Customization can be stopped, if I remember correctly, but you should check this thread: http://forum.xda-developers.com/showthread.php?t=355277&highlight=Polaris+tips+tricks
Hi,
Many thanks.
For the moment I am using a cooked rom Khanx 1.6 Pro.
I was really fed up with the Original Rom as I said it was fine for a few days, working smoothly, even backups by SPB were fine, and suddenly one day the unit froze and I had to reset after the rest nothing worked, all data lost.
Even after Hardreseting I was having problems with 'VDDemon' each time, only after re-installing the rom for a few times I was able to go back to working with it.
I mainly use the unit for telephone (ofcourse), mail, notes and sms.
By the way when I enter bootloader, I can see POLA100 MFG, and the SPL-2.20.Olinex, CPLD-2.
And what I meant about the Automatic ..., when you hard reset the unit you get a windows saying that in 3 seconds and automatic instal is beginning, how can one stop this instal????????
So really I am not even having fun with it at all.
OK, Pola 100 is here too, but SPL is original HTC.
Could you try device for few days with "bare" ROM, meaning no other software installed? Maybe it's software incompatibility.
For stoping customization check thread I mentioned, think it's described there. But I might be wrong, it could be some another thread. In any case, I remember reading about it here and a way how it can be stopped.
My Polaris is stable as stable Windows device can be...
Bodisson said:
OK, Pola 100 is here too, but SPL is original HTC.
Could you try device for few days with "bare" ROM, meaning no other software installed? Maybe it's software incompatibility.
For stoping customization check thread I mentioned, think it's described there. But I might be wrong, it could be some another thread. In any case, I remember reading about it here and a way how it can be stopped.
My Polaris is stable as stable Windows device can be...
Click to expand...
Click to collapse
What do you mean SPL is original HTC?
It is Oli's SPL...
Has anyone experienced their TP crashing during normal operation, and found the only way to recover is through a hard reset?
That's what happened to me last night. I'm running a stock HTC ROM that I upgraded when it came out (two weeks ago?) and the device was working without any problems up until then.
Last night though I was using Opera to browse a website and it suddenly became unstable. I closed Opera and found it wouldn't re-start so I performed a soft-reset. From this point on the device wouldn't go past the boot screen (displaying 'HTC Touch Pro' with the red version numbers - not even getting to the animation). I attempted to soft reset a few times (and even removed the battery for a while) but it still would not boot.
So I performed a hard-reset and restored a backup, whereupon it now seems ok again.
To give a little more info:
- the device was fully charged (had been on charge via USB all day)
- TF3D not installed - standard WM6.1 with SPB Phone Suite installed
- Browsing over wifi (bluetooth and HSDPA connection were also active)
- Running Opera 15613
- Just before the crash, a bug appeared whereby typing a single character into a website textbox (using the slide-out keyboard) would cause that character to be repeated a large number of times on screen - this has never happened before
I've always run the device with the stock HTC ROM and never had any issues like this.
Anyone had anything similar happen?
Yep, just had to hard reset then restore sprite...I was trying to play a song through tf3d and it froze. Soft reset only lead me up to the first screen that states radio version...yaddah yaddah yaddah...hard reset 'solved it'.
Does your phone got hot?
I had a problem while browsing over wifi. To boost the speed i changed power manegment to best performance in wifi settings and phone got hot in few minutes, opera crashed and soft reset didn't help either. But for me removing betery solved the case and also cooling the device a little.
hope this helps
BHole
BHole said:
Does your phone got hot?
I had a problem while browsing over wifi. To boost the speed i changed power manegment to best performance in wifi settings and phone got hot in few minutes, opera crashed and soft reset didn't help either. But for me removing betery solved the case and also cooling the device a little.
BHole
Click to expand...
Click to collapse
It gets warm sometimes, however in this case I'd only been using the device for a few minutes, so I think it was still cold.
I tried removing the battery but that didn't help.
Seems to be behaving itself since then though.
I got the same problem nearly every day. After a few hours (up to 12) it gets frozen. Only hardreset was possible. I got this problem since a view months. I'm trying now to leave one after another program not installed after every necessary hardreset. Currently i'm suspecting either WM6.5 itself, vAlert or some other mortscript apps. For now i don't installed vAlert and there is no crash since over 24 h.
The following programs are innocent:
- tf3d
- pointui
- SmsReportsEraser
Surprisingly enough, I had the exact same problem just the other day. I got my TP about two weeks ago and was still looking around here learning the ropes of flashing etc and the differences between it and the Mogul. I kinda liked the business card reader that came on the stock rom and couldn't find it as a cab anywhere so I was undecided on flashing a new rom. I also didn't like the TF3d so I wasn't running it. I was using the regular win today screen with spb weather and Phone Suite installed. Worked fine like that for over a week. I got a text message on Tuesday and the TP froze up, so I did a soft-reset. It got frozen on the boot screen just as you described. Fortunately I was able to in hard-spl from the micro disk to unlock it, then I installed NFSFAN's custom rom, also from the micro disk.
Not related to the topic, but I really like how that new rom functions. I added the telus radio as well and now the battery at least makes it through the work day. Before I had to charge it mid day! Only thing I miss is that stupid business card program from the stock rom. If anyone can point me to a cab I'd really appreciate it. I get so many cards its a pain to enter them all manually.
Thanks,
PhilyT
I just started having this problem a couple of days ago. This has happened twice now. Warm-booting did start the reset process (I would get the splash screen), but it never got past that.
i think theres a thread about this somewhere. The cause isnt known but they are trying to pinpoint the problem. Bad rom chip, software problem etc
I've also have been affected by this and its a pain... having to setup the device again.
Mainly this problem has to do with tf3d2 in my case as i try to save a contact each time it will free. So i have to manually enter a phone number and store it.
I guess its better than a hard-reset
Hy,
I ve got the problem that suddenly my TP shows unusually hanging after a few minutes playing around. If i do a softreset then it hangs on the splash screen and nothing happens. I can do a hr then and the same story begins. After tast appeared i flashed some other roms to be sure that its not depending from the rom. Also i restored different backups, with all its the same... i fear that a part of the memory is defect ... Any ideas how to test the memory or other suggestions? thx in advance.... i dont want to use my microwave
Greetz
Boris
Did this happen suddenly or did you do something before it happened (eg install something, etc)?
Mine just today won't turn on, I had it off all day and now it just sits on the splash screen.
Trying some things, if I figure anything out I'll let you know.
No, i didnt do anything special today or yesterday, but a week ago i set it up completly new, cause i had equal problems.... to set it up completly new with all progs and cosmetic "operations" costs me nearly one week so i dont want to do it again ...
If i find a way to solve, i will post here too
Greetz
Boris
I flashed EnergyROM (booted into the tricolor screen by holding down Power and Volume Down), and it seems to be working.
Youre the lucky one, congrats...
I have a similar problem. The only change/new install is the updated version of Microsoft MyPhone. Now my TP will not connect to my telephone provider: T-Mobile. It just tries and tries but never connects.
Also, sometimes when I try to open any program, I get the error message that the certificate cannot be read. a soft reset fixes this but this problem is driving me crazy.
Is this another Microsoft update ****up?
same here: today more than 3 times problems with certificate or similar message ... thinking of the last timebomb in my old romeos rom ... was no fun..
Borisku,
Are you running Microsoft MyPhone? If so, did you do the software update within the past 4 days?
i do, but i didnt update ... ??? This morning my TP hung again, and i tried to sr it.... seemed to work until tp vibrates 3 times and then nothing anymore, no screen, no button, nothing
.... took out battery, left it out for 30 minutes, then i could HR again and restore my backup... since then no problems.... do you think it could run too long, getting too hot or something like this??
Greetz
Boris..
Edit: was too fast just 1 minute after i wrote that, tp hangs while in connection to active sync.... hr now, will test how it runs with pure romeos2 for 2 days now... rport follows
Edit II: The last days i always flashed from SD Card... i will now try to flash ROMEoS2 from PC ... maybe theres a difference, especially cause the text at the end of flashing from SD was confused. there were mor than one words at one place one the screen, and i found i typing on the screen RaphSimg.nbh, although the file is named as usual raphimg.nbh (without the "s" in the centre...)
I hope i m not too early: i think i solved the prob, maybe that helps somebody & prevents a tp from ending in a microwave
in preparing to bury my tp in the microwave i flashed back to the german stock rom or - correct - to the official update that can be loaded from the HTC Homepage; it contains not only the Rom but also radio & Splash Screen. I flashed it to my tp and was prepared to undo Hard SPL, but it gave it a chance.... and it ran like a VW beetle, flashed back to ROMeOS2, it runs.... i will wait till tomorrow & hope that it will not change to freeze or change clock Font colour partly as it did before...
Hope it will help somebody...
Greetz
Boris
Edit: its now 14th of december and it runs like a charm... seems like the failure is gone through flashing to stock ROM & then flashing ROMeOS again
Still is okay ...