Related
Hello friends, this is my first post in prophet forum, though I had been a ppc user for more than 2 years. 5 months back, I bought an O2 XDA Neo, which was loaded with a dopod rom, with numbers coming up as 2.09.001 etc during startup. Shortly after purchase, I flashed with RUU_Prophet_220734_2207114_024721_QtekWWE_Ship rom. Everything went on well, and I was using the phone without problems for the past 2 - 3 months. Well not exactly without problems, some times when I reset the phone, it gets stuck at the spl, ipl screen, and I have to reset again many times to get it to load windows. I initially thought the problem may be due to the battery not being charged fully, but later I found that battery charge is not the problem, as the phone not booting became more and more common even with a fully charged battery. Even when I managed to get the phone started after repeated and frustrating soft resets, I started to get corrupt PIM data, like the contacts and calendar applications not starting up. ALso strange folders with name y? and y?? appeared in the phone memory. THese folders could be deleted only with Resco Explorer. Also the bluetooth was not working properly, that is when I turn it on using the comm manager, the blue tooth icon gets activated but actually no bluetooth is turned on. Later after a soft reset, bluetooth turns on but now the icon in comm manager is not activated. I did a hard reset a couple of times thinking that this problem will be rectified, but all the problems continued.
Going through the forum i read some where that JAMin_WWE_213923_2139123_022021_ship was one of the most stable roms for this phone, so I set about flashing this rom. I used ROMUpdateUtility-NoVendorID and the update went on till 95 % when it showed error 326. I tried again, with the same result. I later flashed RUU_Prophet_220734_2207114_024721_QtekWWE_Ship back, and the phone is working as before.
NOw I would like to get the following problems corrected
1. Phone getting stuck at ipl, spl, gsm screen
2. Proper working of bluetooth as I would like to use it with my BLueant Supertooth II
WHat will be the correct these prolems ? will the imate rom correct these problems, if so how am I to go about loading it ? or is there a better one than what I am having now ? or is it a HARDWARE problem ?
I am very sorry for this extremely long post, but I felt if I said all my problems in one post, I would get better response.
PLease help....
You should have stayed with the RUU_Prophet_220734_2207114_024721_QtekWWE_Ship ROM from the beginning, since it's the best and also latest official Prophet ROM. It's a 2.20 ROM which is the latest available.
GAMBIT999 said:
You should have stayed with the RUU_Prophet_220734_2207114_024721_QtekWWE_Ship ROM from the beginning, since it's the best and also latest official Prophet ROM. It's a 2.20 ROM which is the latest available.
Click to expand...
Click to collapse
I am still with that ROM. It is with this ROM that my prophet is causing the above problems.
Can you guys advice me how to load JAMin_WWE_213923_2139123_022021_ship rom with out this error 326 showing up ?
After I tried to upgrade the rom to WM6, my JAMin got stuck at bootloader. After that, I tried to flash WM5 roms without success and suddenly (after a reset) the screen became white with some horizontal and vertical lines constantly moving. I discovered that it was only the screen that was garbled as it still connected to PC, so I installed (without seeing anything on my JAMin) the NVID ROM trying to restore it. It installed sucessfully, but the screen remained garbled with the white background and random lines. I know it was sucessfully installed because I heard the typical "welcome" sound before configuration.
Do you know any way to restore the screen? Or must I send it to I-Mate to repair?
You can try and reattach the screen cable to the rest of the device, but this will boid any warranty you have, and may damage your device further. If the device is under warranty, I would suggest flashing the ROM the device came with (unfortunately the FTP server is down at the moment, so it might take some fishing around for) and sending the device back to get repaired properly.
mpmf said:
After I tried to upgrade the rom to WM6, my JAMin got stuck at bootloader. After that, I tried to flash WM5 roms without success and suddenly (after a reset) the screen became white with some horizontal and vertical lines constantly moving. I discovered that it was only the screen that was garbled as it still connected to PC, so I installed (without seeing anything on my JAMin) the NVID ROM trying to restore it. It installed sucessfully, but the screen remained garbled with the white background and random lines. I know it was sucessfully installed because I heard the typical "welcome" sound before configuration.
Do you know any way to restore the screen? Or must I send it to I-Mate to repair?
Click to expand...
Click to collapse
Hi frd,
I have exactly the same problem!
Nothing , only the f*** white screen!
I can browse the device via active sync, can rcv calls but the white screen.
I have checked the ribbon connector of the LCD and make reflashing some ROMs but nothing.
I still wondering is it hardware or software problem!
Please let me know if you have progress!
Thanks
G.
Try to replace LCD module, I think thats right way.
It will be a hard ware problem. Probably the ribbon cable as the screen is showing something so it must be working at least a bit.
Hello,
i have the same Problem with my QTEK S200.
First i changed the Rom and it worked perfectly for two days.
Then i had to change my Sim card and after that the problem came again.
I tryed a lot of times to reflash the rom but the problem persist.
How can it be that it worked again for some days ?!
is it the touchscreen of the lcd unit i have to replace ?
is it possible to do it by my self ?
thanks for your help !
Hi everyone.
I had a similar problem an hour ago (Qtek S200 G3):
I Upgraded to a 6.1 rom and then to another, after that my device was stuck in bootloader(3 colour screen). Any 6.1 rom that I tried would install, but after installation device always boot in to the 3 colour screen.
I tried this original shipped rom http://files.mail.ru/HZUAH1 (it's WorldWidwEnglish) (to download just click the link "скачать" or the file name RUU_Prophet_220734_2207114_024721_QtekWWE_Ship.exe
) and it installed!!! It TAKES A WHILE TO INSTALL!!! But it worked!!!
May want to try it.
Hope this helps.
hello,
picture on screen was immediatly clean again ( bootload image ).
it was impossible to change the rom because i have a G4 model.
i flashed the rom with another french rom for G4 and it worked perfekt.
now i tried to remove the battery again for 3 seconds and now i have the same problem again. really strange ....
i tryed the same procedure again but no success.
I reinstalled differents rom's again starting always installation from bootloader.
After about 10 new installations i've clean picture again.
now i'll not put off, restart, or take of battery till one of you know what's the problem.
Thank you for your help !!
are you guys sure its not an intermitant hardware problem, it sounds like it to me. if yu were able to get a clean picture for a short time and now its white again, it cannot be the rom? As for replacing it, nothing is impossible and there is always ebay and google
QTEK S200 G4 CID unlock
How can I CID unlock a device that need´s that to upgrade the Rom?
Is there already any program that , Lockwiz dont do the job, can performe the unlock?
Thank you.
For G4 CID unlocking, you need to user Hard/Soft SPL.
same problem
my imate jamin got the same problem. it happens only and only when I remove the battery and when I leave it to charge for 1-2 days the LCD works again and show clear pic. any suggestion? activesync and &... are all ok!
Well, i upgraded to windows Mobile 6, but haven't removed the batterie anymore.
But i'm able to put it off now, what was impossible before.
Hello girls and boys,
yesterday my TC first stuck in tricolor screen and shows
POLA100 RUUNBH
SPL-1.25.0000
CPLD-2
and downwards: USB or SERIAL
It happened as I tried to flash back the original Radio for it. The update monitor showed ERROR 262 (0%), before that I had already installed signed_RUU. for original German WM6-ROM and it worked fine exept the decreasing GSM connection.
After that I searched here the whole night for solutions but none of them (MTTY, Radio Murata, UN-SPL, flash Radio or OS from microSD) helped.
I guess it's all I am able to!
Maybe one of you guys can help me?
Or can anybod tell me whether my TC is dead?
Can anyone tell me the meaning of:
POLA100_____________RUUNBH
SPL-1.25.0000
CPL-2
Thats what my tricolor screen shows!
Maybe someone can tell me where I can get the original German RUU....ship.exe for Polaris.
Did you install HardSPL before playing around with your phone?
Yes I did, and it worked fine exept the bad radio issue.
My TC started to hang as I tried to get back.
Hy,
I ve got the problem that suddenly my TP shows unusually hanging after a few minutes playing around. If i do a softreset then it hangs on the splash screen and nothing happens. I can do a hr then and the same story begins. After tast appeared i flashed some other roms to be sure that its not depending from the rom. Also i restored different backups, with all its the same... i fear that a part of the memory is defect ... Any ideas how to test the memory or other suggestions? thx in advance.... i dont want to use my microwave
Greetz
Boris
Did this happen suddenly or did you do something before it happened (eg install something, etc)?
Mine just today won't turn on, I had it off all day and now it just sits on the splash screen.
Trying some things, if I figure anything out I'll let you know.
No, i didnt do anything special today or yesterday, but a week ago i set it up completly new, cause i had equal problems.... to set it up completly new with all progs and cosmetic "operations" costs me nearly one week so i dont want to do it again ...
If i find a way to solve, i will post here too
Greetz
Boris
I flashed EnergyROM (booted into the tricolor screen by holding down Power and Volume Down), and it seems to be working.
Youre the lucky one, congrats...
I have a similar problem. The only change/new install is the updated version of Microsoft MyPhone. Now my TP will not connect to my telephone provider: T-Mobile. It just tries and tries but never connects.
Also, sometimes when I try to open any program, I get the error message that the certificate cannot be read. a soft reset fixes this but this problem is driving me crazy.
Is this another Microsoft update ****up?
same here: today more than 3 times problems with certificate or similar message ... thinking of the last timebomb in my old romeos rom ... was no fun..
Borisku,
Are you running Microsoft MyPhone? If so, did you do the software update within the past 4 days?
i do, but i didnt update ... ??? This morning my TP hung again, and i tried to sr it.... seemed to work until tp vibrates 3 times and then nothing anymore, no screen, no button, nothing
.... took out battery, left it out for 30 minutes, then i could HR again and restore my backup... since then no problems.... do you think it could run too long, getting too hot or something like this??
Greetz
Boris..
Edit: was too fast just 1 minute after i wrote that, tp hangs while in connection to active sync.... hr now, will test how it runs with pure romeos2 for 2 days now... rport follows
Edit II: The last days i always flashed from SD Card... i will now try to flash ROMEoS2 from PC ... maybe theres a difference, especially cause the text at the end of flashing from SD was confused. there were mor than one words at one place one the screen, and i found i typing on the screen RaphSimg.nbh, although the file is named as usual raphimg.nbh (without the "s" in the centre...)
I hope i m not too early: i think i solved the prob, maybe that helps somebody & prevents a tp from ending in a microwave
in preparing to bury my tp in the microwave i flashed back to the german stock rom or - correct - to the official update that can be loaded from the HTC Homepage; it contains not only the Rom but also radio & Splash Screen. I flashed it to my tp and was prepared to undo Hard SPL, but it gave it a chance.... and it ran like a VW beetle, flashed back to ROMeOS2, it runs.... i will wait till tomorrow & hope that it will not change to freeze or change clock Font colour partly as it did before...
Hope it will help somebody...
Greetz
Boris
Edit: its now 14th of december and it runs like a charm... seems like the failure is gone through flashing to stock ROM & then flashing ROMeOS again
Still is okay ...
Good day.......
I am mailing out of real frustration.
I don't know if this is allowed.
I collected a cingular 8125 from a friend in the UK.
I noticed on starting up that there was Tmobile screen first before the windows mobile screen starts. I had no problem with the fone until i realised that i couldnt connect to my local networks GPRS service (who uses a phone that can't browse)
After scanning thru the site, i decided to flash the phone with Crasing's WM6.5 ROM after doing a HardSPL and i could browse and it was the perfect phone apart from the fact that it was real slow and hangs attimes.
It got worse so i got fed up and decided to revert it back to the original ROM and sort the browsing stuff with a network fix that someone on this site had told me.
I reverted the hardSPL and on installing the Tmobile ROM, it brought out an error message, tried with the Cingular ROM same thing.
So i tired reflashing by using a software called Flash Center and it started and stopped at the 1%.
Restarting my phone just shows me the bootloader screen and i have been battling it constantly for 3 weeks but to no avail
I have read almost all forums here, done almost all they ask to do, but nothing.
The only ROM that worked on it is the WIZARD love ROM but it using exactly 21mins to start up. Thot of downloading Faria/Molski WM5 ROM (cos i sorta prefer going back to WM5) but the links for their downloads are dead.
Please help/direct me to where i can see help cos i really need the phone like 2 weeks ago. I am most definitely depressed now.
Thanks.
Check here for all HTC Wizard WM5 OEM shipped ROMS. The one for Cingular is listed in there.
http://forum.xda-developers.com/wiki/index.php?title=HTC_Wizard_Windows_Mobile_5.0_Shipped_ROMs
You say the phone is a Cingular (G4 DOC version). Does it look like this one (click link ... http://www.brighthand.com/assets/4811.jpg ) with the Cingular logo on top left, etc?
Did you require the HardSPL to be able to flash to new ROM, or did you just use the SIM / CID unlocker using the Wizard Service Tool (note the Wizard Service Tool will only work for G3 DOC type device, not the G4 DOC devices)
You said you also removed the HardSPL. If you removed the HardSPL, then you can only flach the OEM ROMS (i.e., if yours is Cingular, then you can only flash the Cingular Stock ROM ... check link above and use Cingular 2.25 (click here ...
... http://www.4shared.com/file/BJUEhCC9/RUU_Wizard_Cingular_8125_WIZCN.html )
First do a battery pull, replace battery, then start device in bootloader mode (i.e., press and hold Camera button on side, then using the stylus press and release Reset button on same side. Do NOT power up the unit by trying to turn on using the Power button on top). Take note of IPL and SPL version that shows up on Bootloader (3 colour) screen. Then plug in USB and try re-flashing with Cingular OEM ROM.
After successful OEM ROM you can then try HardSPL again and re-flash to other ROMS. There are plenty of cooked WM5 and WM6.1 ROMS out there. The WM6.5 is too much (I think) for these devices. A neat clean simple WM5 or WM6.1 with overclocking works very good.
Regarding your settings for ISO, GPRS, WAP etc. you can look for a Netwrok Wizard cab file, and install ( heres the newest I could find ...
http://forum.xda-developers.com/attachment.php?attachmentid=121023&d=1223800573). This will install 6 files into the root Windows directory of the phone. Reboot the phone and you will notice the Network Wizard icon show up in the Settings/Connection control panel.
One of the files it installs is called provision.zip. You will want to update this by copying the following to the windows directory overwriting the old one. This contains all the settings for your phone. Once you copy this over, click on the wizard in the Connection Settings control panel, and it should give you options for Country and Cell Phone carrier/provider. Click away and it shoould automatically set up the correct info for WAP, GPRS, ISP, MMS, etc.
Good Luck. Let me know what happens.
WOW
Thanks for the response
I used the HardSPL to flash the new ROM.
I removed the HardSPL and the Olip in my IPL was changed back to the 2.26.0001
I tried the cingular 2.25 ROM but it says it wasn't meant for the device and most times the RUU doesn't recognise the phone. Tried the Tmobile 2.26 same thing.
Also used crossbow WM5 AKU2.3 and AKU3.3 ROMs they worked but fails at 96%
The only ROMs that worked is Wizard Love ROM but it spends about 20mins to get to the part where it asks you to align screen and it doesn't move from there
Thanks for the info on the WM5/WM6 also the network wizard cab file. Really hope that phone works
I'm a pretty desperate guy right now cos i use the phone to trade and money is moving, she(money) is a *****
WOW
Thanks for the response
About the pix you reffered to? Yes thats exactly how my phone looks like
I had used the HardSPL to flash the new ROM.
I removed the HardSPL and the Olip in my IPL was changed back to the 2.26.0001, SPL 2.26.0001
I tried the cingular 2.25 ROM but it says it wasn't meant for the device and most times the RUU doesn't recognise the phone. Tried the Tmobile 2.26 same thing.
Also used crossbow WM5 AKU2.3 and AKU3.3 ROMs they worked but fails at 96%
The only ROMs that worked is Wizard Love ROM but it spends about 20mins to get to the part where it asks you to align screen and it doesn't move from there
Thanks for the info on the WM5/WM6 also the network wizard cab file. Really hope that phone works
I'm a pretty desperate guy right now cos i use the phone to trade and money is moving, she(money) is a *****
PS: My IPL/SPL is 2.26.0001
OK. Good info.
Not sure how you did it but somehow you managed to get the T-Mobile IPL/SPL on it, and yet it still recognizes it is Cingular. For one reason or another one aspect does not let the other load and vice versa. ????? Hhhmmmnnn ????
Here is what I would try.
1) I have attached a zip file called SoftSPL. Inside I have made an image file nk.nbf, which contains ONLY the 2.25.0001 IPL and SPL for the Cingular 8125.
Unzip this folder to your Desktop and then try to run only the "newromupdateutility_wizard_noid.exe". Remember, start the phone up in bootloader mode, connect via USB then run the "newrom...exe" file. If you get an error right away saying this is not the right update utility for the phone or something like that, then start over ... i.e., disconnect phone, pull battery, start phone in bootloader mode,reconnect via USB, but this second time try using the one called "2.exe". I found sometimes when I flashed ROMS the first one did not work and the second one (2.exe) did for me.
IF this works, once you get the 2.25.0001 IPL and SPL showing on the bootloader screen then start again (pull battery etc. same as above) but then re-flash back to the original Cingular OEM 2.25 ROM that you tried earlier (the original RUU_Wizard_225111_22511102_022511_CWS_WWE_Ship_1.exe). Try this and let me know how it goes.
If and when you get it back to the original Cingular ROM, if you get to this point, you can then start back like it was when phone was "new". It will still be SIM unlocked so you can use any carriers SIM card but you cannot flash other ROMs.
If you are going to try other ROMs, re-apply the HardSPL, but make sure you only use ROMs that have been cooked, say they are safe for G4 devices and do not have IPL/SPL in them. This means when you have it HardSPL'd you cannot, or should not use other carriers OEM ROM's such as T-Mobile 2.26 or 3.08.
Lastly, if you do like some of the "extra's" offered with WM6 or higher and do not like a slow phone and want to keep it fast like a WM5 ROM, then stick to either WM6.0 or WM6.1, clean (or what they call Vanilla) ROMs.
Good Luck. Give feedback of how it works out for you and pay attention to errors and messages and IPL/SPL etc. for reporting back and I can help you a little more.
Another thanks again.
I really owe you if and when my phone is finally done cos i think i am getting there.
But i successfully changed the IPL/SPL but on flashing the cingular ROM it says the RUU cannot see my phone and once it sees that it says the update utility cannot be used for my phone.
So what next?
Maybe the ROM is not the right one but i ensure it was meant for g4 tho"
Tried MUN-RUU but to no avail
Eagerly waiting your reply.
Thanks again
OK. YES. You are getting there.
You say the phone is now IPL/SPL 2.25.0001. It shows this on the 3 colour bootloader screen?
What did you run in order to flash; did you run the "newromupdateutility_wizard.exe", or "2.exe", or did you need to run the "START-sSPL.exe" to flash th nk.nbf file I made? (I don't think the "START-sSPL.exe" works from the bootloader screen...phone has to be booted to working status).
Here's what is next. I made a new nk.nbf which is the Cingular 2.25 OS, splash screens and 2.25 radio only. I removed the IPL/SPL and the Extended_ROM, and cooked this back to nk.nbf.
Download it from here .....
http://www.fileswap.com/dl/7WhstX82/nk.nbf.html
..... and copy this to the folder you made of the SoftSPL earlier (overwriting the other nk.nbf - you may want to save that as a back up)
Now try flashing this new nk.nbf again as you did for the IPL/SPL.
If it works, then let the phone boot up completely. Check it out. And then you can run the RUU for the original Cingular OEM once the phone is booted to get it back to Cingular OEM state (full IPL/SPL, OS, GSM, Extended_ROM, etc.)
From here (if you make it) then any further flashing of ROMs, you will want to flash G4 safe ROM's, and you can do this using the SoftSPL folder. Copy the nk.nbf from the custom ROM you want to flash into the SoftSPL folder and run the "START-sSPL.exe" with your phone connected (not in bootloader mode, has to be completely started up and recognized by ActiveSync, but you do not need to establish partnership ... just skip/cancel that part and phone will connect to ActiveSync as a "Guest").
Good Luck. Let me know how you make out with this.
Just to answer your questions.
I ran the "newromupdateutility_wizard.exe"
Would follow thy new instruction sire and get back to thee.....lol
Thanks again.
I am not here to say "Yipee, its done'
But rather to say that the universe, cingular and the god of communication might have just conspired against me.
Just when i think i would finally get my phone working after 3 weeks, a 2 yr old kid took my batteries and only God know where that batteries is now.
Tried to buy a new one but all i get is "Wow! that a pretty old uncommon phone here"
I intend to use an ac to dc converter and when i am done i would give you the feedback
Thanks
PS: Just wanted to give you the heads-up
So i found the battery early this a.m.
Flashed the phone with the ROM you uploaded and it was succesful but on starting it i get a green screen and its damn slow and doesn't even pass the spot where you are asked to align screen (i really do think that nothing happen and its still the Wizard Love ROM that its still booting into)
So I am still stuck?
Hmmm....
OK i guess there might be a psych diagnosis for what i am doing (posting excessive replies without any respond)
It just a worried person.
So i kept re-trying to flash the ROM on my phone about 2ce.
Then i noticed on the 2nd time at about 86% the phone seemed to restart itself into bootloader mode about 2-3X, so i thot the battery was running out. Decided to take it out and get it charged.
On plugging the battery back to the phone all i got was a white screen and starting it on bootloader mode OR hard-resetting still gives me that white screen. On removing the battery the phone flashes like once or twice.
Is this the end? The phone has brought an apocalypse on?
Been doing a lot of browsing for clues but nothing tangible yet.
God smiled on me and the phone started
Got the ROM you gave me flashed and its really refreshing to see the Windows Mobile logo again
But i am stuck at the align screen tho'
I tap and nothing happens unless i drag the target and it just moves around and get back to the original spot.
Thats the latest pal.
OOPS. I did not read all .... your posts ... I just answered your post at the end of the last page. Did not see these last 2.
This is a good sign that you get past the initial boot splash screens and make it to the Align Screen ... soft reset the phone again and look at the IPL SPL that shows on the screen. Is it 2.25.0001 or 2.26.0001?
If 2.25.0001 then let the phone boot up to the Align Screen (and if you cannot get past this then just leave it at this point). Plug back into computer and now try to flash Cingular OEM ROM 2.25 that you tried earlier using the stock file.
If this doesn't let you flash for the same reasons as before (i.e., Invalid RUU tool or Not correct operator) then extract the nk.nbf from the Stock Cingular ROM (right click on the Cingular RUU OEM exe and select "Extract here ...".) then copy the nk.nbf over to the Soft SPL folder and use the START-sSPL.exe and flash this way. (you can delete the rest of the files from the Extract process.
Good Luck. Let me know the IPL SPL you get.
I know my posts are getting sickening but i am really desperate.
Got some info about how to bypass the align screen online but couldn't get my phone to boot anymore.
Soft reset/Hard reset/Bootloader mode: All of it just shows a white screen and nothin more.
Any ideas?
PS:The last time i could start the phone the IPL/SPL was 2.25.0001.
Just want to add this cos i just noticed it:
1. Sometimes tapping the Camera button alone puts the phone on (tho' it shows that annoying white screen)
2. On connecting the phone to a PC the PC recognises it even tho' its off and once i put it on and that annoying white screen comes on, the PC gives the same sound as when a USB is detached.
Hope these info would help.
I"m really getting depressed now. Hope's looking dimmer.
OK. I am now suspecting that you may also have a battery problem. How old is the battery. Could be the battery no longer has enough capacity. It may charge but only hold a charge for very short time and voltage may be too low. Maybe enough power to keep some of the electronics "awake" but not enough to drive the LCD.
It is now IPL/SPL 2.25.0001 so it should be able to flash the Cingular OEM ROM. You may want to try a different battery. Other than this, if not a problem with the battery then I think maybe phone itself is coming to an end.
I would try the battery route, making sure you have a good power source, and then try to flash the stock Cingular ROM.
You can still get these batteries on ebay and phone as well. If you are going to spend any money then maybe instead consider a newer model phone on ebay. (if you are patient you can find very good deal ... I got the T-Mo MDA Vario version of the Wizard (WIZA200) for $25 plus shipping, brand new with a carrying case. It was an estate item from a salesman who passed away and phone was not used before he passed on. One man's misfortune, another man's luck. I am now selling this on ebay plus memory card and earphone here ... http://bit.ly/hDHxrW. I have two more on sale at ebay here... http://bit.ly/eV0zZh ... and here ... http://bit.ly/gLIiKh. I am selling 3 and I have upgraded to Touch Pro 2. Go with AT&T version as this can beused world wide on 3G in North America and is quad band GSM for use in rest of world)
WOW
Thanks Bud
I would change the batteries and really don't mind buying another one but the only problem is i am not in USA nor Canada except i give an address in the US to send it to.
PS: Got to the links and it was a bidding process that was over by the time i got there. If anything opens up you can holla at me.
Would get back to you if there are any new developments
WOW
Thanks Bud
I would change the batteries and really don't mind buying another one but the only problem is i am not in USA nor Canada except i give an address in the US to send it to.
PS: Got to the links and it was a bidding process that was over by the time i got there. If anything opens up you can holla at me.
Would get back to you if there are any new developments
Cheap battery on ebay ..
http://cgi.ebay.ca/New-Li-ion-Batte...652056?pt=PDA_Accessories&hash=item5d2d297c58
http://cgi.ebay.ca/Battery-HTC-Wiza...163910?pt=PDA_Accessories&hash=item45f7ebb846
Phone
Wizards
http://cgi.ebay.ca/HTC-MDA-Mobile-S...0528835033?pt=Cell_Phones&hash=item4cf50dc5d9