Dopod/Prophet 818pro Need Help - JAMin, XDA Neo, S200 Software Upgrading

Hello,
I download wm6.1 rom Prophet_ShadoW_2.0_CE and successfully updated my wm5 to wm6.1
Now, i got problem with WiFi. Can detect access point. But i can't connect to it. Setting and passwd all same like b4 in wm5.
Pls help !!!

leongyap said:
Hello,
I download wm6.1 rom Prophet_ShadoW_2.0_CE and successfully updated my wm5 to wm6.1
Now, i got problem with WiFi. Can detect access point. But i can't connect to it. Setting and passwd all same like b4 in wm5.
Pls help !!!
Click to expand...
Click to collapse
1. check your security settings !!
2. did you do a hardreset manually after upgrade?

Hardrest
I hardreset my prophet.
It can detect accesspoint automatically.
enter the WEP manually.
Still the same. can't connect..
Pls help me.

leongyap said:
I hardreset my prophet.
It can detect accesspoint automatically.
enter the WEP manually.
Still the same. can't connect..
Pls help me.
Click to expand...
Click to collapse
did you check you wireless router settings?
be sure that both sides are perfectly matched.
if you choose wep, 64bit or 128bit?
shared or open setting?
did you put 10 digits for the wep key setting?
By the way, which rom you are using?

Related

No sync at all with WM2005

Searched for this fault but no luck,
Put WM2005 on my MDA T-Mobile device (PH10A)
When i connect to USB lead My desktop wont even recognise the device, instead it tries to install it as a "Generic RNDIS (PROTOTYPE--Remember to change idVendor)
Now am i daft and missed something on the final setup, or have i broke it
Anyone else had this?
Cheers,
Mark.
Mark, did you upgrade ActiveSync to at least 4.1? It won't sync with version 3.8....
wasnt that, the PC didnt even recognise the device
the pc dont recognise the device unless activesync does
Same thing happen to me
FYI :
Device : XDA II
Bootloader version : 1.02
Is it because bootloader version ?
If that's because bootloader version, I already have bootloader file v 1.06, how too upgrade it ?
Thanks
bootloader
yes please anybody could share how to upgrade the bootloader, I do have the 1.06 bootloader as well.
thanks.
I have almost the same problem, JasJar with rom ver (before 1.30.82) dated may 2005, pc with xp + sp2 and I always get " rndismpx.sys" file missing when try to sync my mobile, and hence it is always not connected.
wud upgrade to 1.30.82 dated 2/22/06 solve the problem, or I must do something else. By the way, I did de-activate my firewall , but no way.
Thanks M Seif
============================
mas-audio said:
Searched for this fault but no luck,
Put WM2005 on my MDA T-Mobile device (PH10A)
When i connect to USB lead My desktop wont even recognise the device, instead it tries to install it as a "Generic RNDIS (PROTOTYPE--Remember to change idVendor)
Now am i daft and missed something on the final setup, or have i broke it
Anyone else had this?
Cheers,
Mark.
Click to expand...
Click to collapse

Graphics problems after WM6 upgrade

Hi there
I'm a noob to PDA things but I decided to upgrade my S200 to WM6 (that was NOT a good idea!)
After downloading this http://rs23l34.rapidshare.com/files/17953287/3266540/smart1_wm6_pp8mb.exe file I run the upgrade batch file BUT it was working for 50min so I unplugged the device. I probably should not do that!! ...because there are some problems: no ringtone for incoming calls, no digits to dial an outgoing call and many theme problems.
Now I'm not able to connect it to activesync (4.5) to do a downgrade because a message comes up that says "ActiveSync cannot connect to the WM device" and there's a network icon on the tray with limited connectivity. I did 3 hard resets by holding power + camera + comm manager buttons + reset and I've tried the trick with the camera button pressed while powering on and after connect it to USB but still nothing...
Can someone help??? I'd like to have WM6 installed but I really have to fix my phone even If I have to setup WM5 again.
Many thanks
Try to make a RUU downgrade in bootloader mode!
Way 1: Download the ROM from the 02 homepage and after 15 min you have a fully useable WM5 device!
Way 2: To reinstall an another WM6 Rom you have to flash AKU2.2 and then you can try to install a different WM6 Rom! You can find AKU2.2 in the threads of the WM6 Roms. The name of the file is often ...TEMP.zip like in PDA Viet!
Happy flashing!
greetz Ben
Hardcore898 said:
Try to make a RUU downgrade in bootloader mode!
Download the ROM from the 02 homepage and after 15 min you have a fully useable WM5 device!
greetz Ben
Click to expand...
Click to collapse
How I'll do that? There is no connection to activesync
Is there any way to flash from the memory card?
In active sync, disable connect through USB. Then enter bootloader (Camera button and soft reset), and then run the RUU. Your device should start properly now.
Great!!!!!!!! it worked!!!!!
Thanks a lot
No problem.

ROM Update Utility loose connection.

Hi guys,
can someone help me ?
I want to flash my XDA Neo with a new ROM (WM6)
However,
I have successfully connected my Phone with ActiveSync 4.5 on WinXP SP2
Then I run an RUU Utility.
The Phone goes into Bootloader (RGB Screen) and then the connection is lost.
From then I couldn't etablish a connection to the Phone.
Is there another way to flash the ROM of my Phone ? e.g. from SD Card directly ?
Any help appreciated - thx
Flashx4u said:
Hi guys,
can someone help me ?
I want to flash my XDA Neo with a new ROM (WM6)
However,
I have successfully connected my Phone with ActiveSync 4.5 on WinXP SP2
Then I run an RUU Utility.
The Phone goes into Bootloader (RGB Screen) and then the connection is lost.
From then I couldn't etablish a connection to the Phone.
Is there another way to flash the ROM of my Phone ? e.g. from SD Card directly ?
Any help appreciated - thx
Click to expand...
Click to collapse
I would join to this question - I have the same problem: somewhere in the middle of flashing my Prophet with Prophet_PV_Temp my Prophet started a dead-cycle with connecting-disconnecting...And I can not reflash it. Now I also have Bootloader (RGB screen) which is on when Prophet is not connected to PC and when I connect it to PC, it disconnects-reconnects-disconnects-reconnects-......
What is the solution?
The problem SOLVED!
ZRimaZ said:
I would join to this question - I have the same problem: somewhere in the middle of flashing my Prophet with Prophet_PV_Temp my Prophet started a dead-cycle with connecting-disconnecting...And I can not reflash it. Now I also have Bootloader (RGB screen) which is on when Prophet is not connected to PC and when I connect it to PC, it disconnects-reconnects-disconnects-reconnects-......
What is the solution?
Click to expand...
Click to collapse
So ,finally I found the solution with this issue and problem with my Prophet's restarting after it's registering to the cellular network (I wrote about it in another treeds as well).
After I tried to reflash my Prophet with different WM6 ROMs, different Radio ROMs, reassembled and cleaned it, reflashed to original WM5 ROM and nothing helped, I just came to an idee to replace the battery, unless Prophet indicated that still it's a lot of power (min 50%)...I ordered the battery and when I received it and replaced, everything is running as it should be!!!!

I-Mate Jam Bootloader & Connection error!

Hello XDA Nice Team !
By mistaken i wrote some file to my bootloader in my I-Mate Jam ..
That was after using the bad ROM : 2.03
it's the worst cooked version i saw !
Now my bootloader mode is working .. but no way to connect to PC with USB port ..
My computer does not recognize my Magican when plugged in bootloader mode anymore!
Bootloader Ver: 1.0
is there any way to fix or upgrade or restore original bootloader
Now i cant upgrade or downgrade my magican by any method
Noway to use successful connection with any roomupdate utility
Please help me to fix or restore my bootloader!
Thanks to any one read or replay or try to help or help me to resolve my problem
XDA lover
i'm sorry that happened mate...
i've had success with flash-from-bootloader attempts before, both on my Magician, when i accidentally flashed off of Vista and it'd enter the bootloader every week or on a reset using the reset hole, and also on my Wizard when i ignored warnings from WM5torage and it'd only enter the bootloader
what precisely happens when you connect to the PC, allow USB connections in AS/MDC, and let the phone enter bootloader however it does? i can just flash a rom from there, but i won't (iirc) get any reports of as recognising the device...
My experience:
1- when i plug my sd card into my jam .. usb not recognized in bootloader mood !!
2- when i use puty or roomupdate it reaches to USB> then when i type any command it does not respond !
3- i could do something .. i let my phone bootup and this i-mate logon screen stays 4ever .. i connected my ppc to pc and i could explre my imate by activesync ...
i could reach something .. when i explore my phone and remove everything from startup folder .. my phone boots .. and i can see start botton .. no touch alignment comes .. and everything works .. but.. screen is virtually reversed .. i can see the OK botton but i must click on the facing area and it be clicked ..
i think i executed some wrong hard SPL to my phone ant that happened >
is there any way to resolve this problem?
is there any way to erase flash on my I-Mate Jam????
is there any way flash my phone?
i also have prepaid JAFWM with pkey and USB cable .. no BOX ..
Help please!
that's messed up... howsabout flashing it at the point when the phone boots up? if there's an AS connection there, then it may work... i'd flash to an official rom though
Same problem , PLS Help !!!
Thx for help
You should check USB connection I think...
Try plug your battery out of device and wait a moment (e.g.10 minutes) and try again,sometimes it will be fine when you did this.
If your magician isn't detected at ALL by your PC when plugging the USB cable into it (i mean, no new hardware; no unrecognized hardware; nothing is detected in your PC when you plug the USB cable), and unless you had previously made a SD backup of your entire Flash with this procedure ( http://wiki.xda-developers.com/index.php?pagename=MagicianSDflash ), then your only option will be to build a JTAG diag cable:
Here are some general directions / ideias:
Magician JTAG pinout: http://wiki.xda-developers.com/index.php?pagename=MagicianJTAG
How to build/run the JTAG: http://wiki.xda-developers.com/index.php?pagename=DeadBoot
Photos : http://www.cf-box.com/htm_data/55/0912/1679.html
Some interesting stuff for debugging problems: http://pda2u.ru/ptopic205.html
For sure cotulla has one built so to test his ROMs + bootloader - maybe he will be willing to give you some directions if you run into problems, and above all, give you a prepared .nb0 (with the bootloader file) for your magician, which i do not know if there's one out there, extracted from an original ROM.
Anyway, you can always try and do it for yourself using itsme utilities. Follow this link: http://forum.xda-developers.com/showthread.php?t=218643
Regards
Keeper,you're awesome! I'm searching for JTAG,too
xiaojin1985 said:
You should check USB connection I think...
Try plug your battery out of device and wait a moment (e.g.10 minutes) and try again,sometimes it will be fine when you did this.
Click to expand...
Click to collapse
Dear xiaojin1985 ,
Thx for your help, But unfortunately i tried your solution but it dosnt work !
Dear Keeper,
Thanks too for your help,
and i think the solution for my problem is one of the solutions you says ( How to build/run the JTAG: ) ,
but the pictures is not available anymore , so pls can you get the pictures ?
All the pictures are in here:
http://s218.photobucket.com/albums/cc23/alex_beda/ and in attachment there's a .mth file with all the pics built-in.
Don't take it wrong what i'm about to say, but in all honesty if you can't figure this out yourself (digging up the internet for the missing pics), i would suggest that you shouldn't try this, since this ain't easy at ALL...
Just to give you some ideias, it will require you to adapt your magician test point signals (TDO;TDI; nRESET; etc,)seen on the magician pinout pic to what is said; solder very thin wires (best done with a small hot air tip); fixate the small dip switch (micro switch) to be always on; keep the USB connected...idk... plus alot of other small details which ain't easy to accomplish.
Personally i haven't tried this yet but for sure it would work
If you decide to go ahead, please post some results!
Connection error solution
this is my problem
hi all. A friend of mine gave me an S100, and after i played for a few days with it, i decided to update it's rom. A "country error" problem appeared,cause i have the greek version, so i ran MaUpgradeUt_noID.exe which completed (as showed 100% process). My (new) problem is that i cannot update anymore. Every time i enter boot menu, i ran the upgrade
(HTCMAG_ROM_WWE_O2.rar) following all the steps normally. When the device resets (so the upgrade is going to start), it's re-reseting again and showing ERROR 101 connection error. Any ideas?
Qtek Greek version
R 1.12.00
G 1337.42
D 1.12.00 WWE
P.S. apart the problem everything is function properly
and the solution
hard reset
plug usb (uncheck allow usb connection in activesynch )
run MaUpgradeUt.exe radio_1.11_greek but idont reset the qtek in first screen
and upgrate downgrate start all ok
reset
welcome screen
hard reset
plug usb (uncheck allow usb connection in activesynch )
run MaUpgradeUt.exe MagicianRadio_1.12.10. uk but idont reset the qteki n first screen
upgrate from radio 1.11 to 1.12.10
reset
welcome screen
hard reset
plug usb (uncheck allow usb connection in activesynch )
run HTCMAG_ROM_WWE_O5_251209
everything is ok my magisian run the new Rom
here..........................

Need Help Badly

i'm trying to pair my bluetooth headset (Samsung WEP200) but everytime i put the pin number (that is given by the bluetooth headset) it always said "Your Device did not connect with Samsung WEP200. The connection Failed or the passcode is incorrect".
and how to install the hotfix (the hot fix from HTC website) on my HTC Touch Pro? everytime i copy the .exe file into my device, and run it, i always got an error box. Incorrect Device, "Please use the correct Device to Install This Hotfix program!" i don't know how it happen, i download this from HTC support page. i select the phone (HTC Touch Pro) and in the "Software Download" tab it show that there are 3 available download, the Hotfix, the Rom and Application.
can someone help me please?? i believe someone having the same problem in pairing their bluetooth headset. so someone who already solve this problem please help me....
i've been searching some help for this matter but i have not got any answer yet....
thank you
For the bluetooth headset try pairing without a password, just press done, it should pair.
I'm not sure about the hotfix but maybe is a pc file? Try running it on your pc.
palmbluetooth said:
For the bluetooth headset try pairing without a password, just press done, it should pair.
I'm not sure about the hotfix but maybe is a pc file? Try running it on your pc.
Click to expand...
Click to collapse
but if i don't type the passcode, it won't let me press next button.. is there any other suggestion?? or is there any .cab file that i need to install first??? since this bluetooth is working perfectly with my other phone.
There is no cab file to install -- this works out of the box. Have you tried pairing with any other device? Are you using the hardware keyboard or the SIP to enter the code? If the keyboard, are you sure you engaged numlock?
i think i remember that somebody said u should try 0000
i tried 0000 (which is the pin that i got from my bluetooth device) already.. when i entered the passcode, i already tried both method, using the SIP ,and the keyboard... but still it's not working... and give me the same error...
emesbe said:
There is no cab file to install -- this works out of the box. Have you tried pairing with any other device? Are you using the hardware keyboard or the SIP to enter the code? If the keyboard, are you sure you engaged numlock?
Click to expand...
Click to collapse
yes i tried to paired my buetooth device with other device (my other phone Nokia N73) and it's working perfectly fine....
excelex said:
yes i tried to paired my buetooth device with other device (my other phone Nokia N73) and it's working perfectly fine....
Click to expand...
Click to collapse
Not my question. Have you tried pairing your phone with another bluetooth device?
emesbe said:
Not my question. Have you tried pairing your phone with another bluetooth device?
Click to expand...
Click to collapse
umm i tried to pair my HTC with my N73, it paired perfectly fine... umm but i have not try to pair my HTC with any other bluetooth device... might be later i will try to pair it with mu bluetoohn dongle...
thank you

Categories

Resources