Hi guys,
can someone help me ?
I want to flash my XDA Neo with a new ROM (WM6)
However,
I have successfully connected my Phone with ActiveSync 4.5 on WinXP SP2
Then I run an RUU Utility.
The Phone goes into Bootloader (RGB Screen) and then the connection is lost.
From then I couldn't etablish a connection to the Phone.
Is there another way to flash the ROM of my Phone ? e.g. from SD Card directly ?
Any help appreciated - thx
Flashx4u said:
Hi guys,
can someone help me ?
I want to flash my XDA Neo with a new ROM (WM6)
However,
I have successfully connected my Phone with ActiveSync 4.5 on WinXP SP2
Then I run an RUU Utility.
The Phone goes into Bootloader (RGB Screen) and then the connection is lost.
From then I couldn't etablish a connection to the Phone.
Is there another way to flash the ROM of my Phone ? e.g. from SD Card directly ?
Any help appreciated - thx
Click to expand...
Click to collapse
I would join to this question - I have the same problem: somewhere in the middle of flashing my Prophet with Prophet_PV_Temp my Prophet started a dead-cycle with connecting-disconnecting...And I can not reflash it. Now I also have Bootloader (RGB screen) which is on when Prophet is not connected to PC and when I connect it to PC, it disconnects-reconnects-disconnects-reconnects-......
What is the solution?
The problem SOLVED!
ZRimaZ said:
I would join to this question - I have the same problem: somewhere in the middle of flashing my Prophet with Prophet_PV_Temp my Prophet started a dead-cycle with connecting-disconnecting...And I can not reflash it. Now I also have Bootloader (RGB screen) which is on when Prophet is not connected to PC and when I connect it to PC, it disconnects-reconnects-disconnects-reconnects-......
What is the solution?
Click to expand...
Click to collapse
So ,finally I found the solution with this issue and problem with my Prophet's restarting after it's registering to the cellular network (I wrote about it in another treeds as well).
After I tried to reflash my Prophet with different WM6 ROMs, different Radio ROMs, reassembled and cleaned it, reflashed to original WM5 ROM and nothing helped, I just came to an idee to replace the battery, unless Prophet indicated that still it's a lot of power (min 50%)...I ordered the battery and when I received it and replaced, everything is running as it should be!!!!
Related
hello everyone. i just bought a g3 wich remains stuck in the ipl/spl screen. i tried VIPPIE 's tutorial (many thanks man for ur work) and flash button rom 1.05 to revive the phone. it flashed without any error , but same result. phone doesnt pass the ipl/spl screen. next i tried to flash Xda_MiniS_LaunchROM_v154102, flashed ok but nothing happend. i m just stuck on the ipl/spl screen. the phone isnt bricked but i can not start it to do a soft spl and flash it. any ideas ?
because it s an o2 xda mini s , i thought an original o2 rom would do the trick (start the phone) but i couldnt find an original rom (tried the xda dev ftp page and the o2 one).
many thanks
hehh
same happend to me once. Go online and finde botton run , update utility 2.00.1
go step by step:
Disconnect your phone from the usb cable,disable any Firewall and Anti virus and reboot your Pc.
1. Make sure your phone is not Connected to the PC and remove the dummy card or SD/MMC card
2. On your Desktop PC, open Microsoft ActiveSync, then go to File >Connection Settings >Remove the Selection from “Allow USB Connection with this desktop computer”
3. Reconnect your phone to the Desktop PC using the USB Cradle and the Charger MUST be Connected to the Cradle (Don’t Bluetooth for the Upgrade)
4. When you see usb appear at the bottom of bootloader screen
5. Run the Upgrade again and it will work fine without any problems.
While upgrading, the ActiveSync program will not go on, however the upgrade is running.
After then, install origial ROM. (u can try T-Mobile MDA Software Version (2.26.10.2) )
Let me know if it's working
ty man for ur reply , i have tried every possible solution, including mtty! no luck. from ur post i didnt understand the following
Go online and find botton run , update utility 2.00.1
Click to expand...
Click to collapse
did u mean button rom . if yes , what the 'update utility 2.00.1' ?
ty
can i use mtty to revive my phone? i found some command for erasing my entire rom in the phone , but it doesnt seem to work . help me
I have flashed dutty's v4 rom and i want to change it
the problem is that when i try to do so i run
KaiserCustomRUU
my device goes into the 4 stripes screen it says usb
but then the program in the pc says error 260 and doesn't load the new rom
my phone still works as dutty's rom is still in but what can i do to change it?
Thank you and i have searched a lot but could not find a solution
thimiost said:
I have flashed dutty's v4 rom and i want to change it
the problem is that when i try to do so i run
KaiserCustomRUU
my device goes into the 4 stripes screen it says usb
but then the program in the pc says error 260 and doesn't load the new rom
my phone still works as dutty's rom is still in but what can i do to change it?
Thank you and i have searched a lot but could not find a solution
Click to expand...
Click to collapse
OK lets start at the basics...... In bootloader mode (tricolour screen) what text does it say at top of the screen?
Have you DEFINITELY Sim Unlocked and CID unlocked?
it says these things
kais130 mfg
spl-10.0.Olipof
cpld-8
Ok that confirms you have the capability to flash. I have seen in the past some people have managed to flash one time only using jumpspl but then their device reverts back to original bootloader...I was one of those people
Next question then...Can you boot the phone normally and gain an activsync connection to it?
yes
i can use my phone normally
only i cannot put a new image in
Are you using Xp or vista? If using vista it may be worth trying a reboot... sometimes it goes doolally with its usb ports. If you cannot see the phone through WMDC or activsync after a reboot it is worth going to SYSTEM (on your PC) viewing non present devices through device manager,( Drop to Command prompt and type... Devmgmt.msc set DEVMGR_SHOW_NONPRESENT_DEVICES=1 ) removing the relevant phone connection and then re attaching it so that windows re detects it.
If you can get a connection via actvisync (win XP) or WMDC (vista) to your phone then all should be ok. Uncheck the activesync/ WMDC "allow USB connections" and try again.
If this still doesn't work then search around here for MTTY. That will allow you to specify the usb connection to the device...amongst other things.
thank you for your time
i have win xp and activesync works nice
the problem is when bootloader starts
When you attempt flashing, do you do it from the device already booted into windows mobile or direct from bootloader?
Which ever way you have tried it, try ther other way.
Not teaching you to suck eggs but just in case you dont know.... To get direct to bootloader hold camera button and soft reset with stylus whilst holding camera button down and the tri colour screen should appear.
With device at the bootloader screen, Can you confirm that you hear the windows "noise" when you unplug and re plug the USB cable just as you would when plugging and unplugging the device normally. This will determine if the device has connection at the bootlaoder stage.
why not just flash using the microsd card. its much easier that way
yes it has connection
the thing is that i have already flashed as i told before with dutty's v4
now i can't
Usually Error 260's are related to the USB port functionality ( Port can't be opened etc).
The SD card method or MTTY should sort you out.
thx again
hope it works
at least the sd trick worked!!!!
now running on winmob 6.1
Glad to hear you sorted it.
almost
i cannot use my sd card cause i have to have it formated in order to put a new rom in
thimiost said:
i cannot use my sd card cause i have to have it formated in order to put a new rom in
Click to expand...
Click to collapse
disable USB connections in ActiveSync and flash.
This Link gives a list of eror codes for Hermes, and probably the same for Kaiser.
It's likely that you have a USB port error - maybe try changing the USB port you use or a different sync cable - or just stick to SD card flashing in the future - I keep an old 1gig card for this.
this IS the problem...i cannot flash...
it stays in the bootloader with the message i wrote
thimiost said:
it stays in the bootloader with the message i wrote
Click to expand...
Click to collapse
It happen to me before hardspl again fix it, not sure why
you mean use the sd method to do hardspl again?
OHHH lord dutty we need your new rom
Hello XDA Nice Team !
By mistaken i wrote some file to my bootloader in my I-Mate Jam ..
That was after using the bad ROM : 2.03
it's the worst cooked version i saw !
Now my bootloader mode is working .. but no way to connect to PC with USB port ..
My computer does not recognize my Magican when plugged in bootloader mode anymore!
Bootloader Ver: 1.0
is there any way to fix or upgrade or restore original bootloader
Now i cant upgrade or downgrade my magican by any method
Noway to use successful connection with any roomupdate utility
Please help me to fix or restore my bootloader!
Thanks to any one read or replay or try to help or help me to resolve my problem
XDA lover
i'm sorry that happened mate...
i've had success with flash-from-bootloader attempts before, both on my Magician, when i accidentally flashed off of Vista and it'd enter the bootloader every week or on a reset using the reset hole, and also on my Wizard when i ignored warnings from WM5torage and it'd only enter the bootloader
what precisely happens when you connect to the PC, allow USB connections in AS/MDC, and let the phone enter bootloader however it does? i can just flash a rom from there, but i won't (iirc) get any reports of as recognising the device...
My experience:
1- when i plug my sd card into my jam .. usb not recognized in bootloader mood !!
2- when i use puty or roomupdate it reaches to USB> then when i type any command it does not respond !
3- i could do something .. i let my phone bootup and this i-mate logon screen stays 4ever .. i connected my ppc to pc and i could explre my imate by activesync ...
i could reach something .. when i explore my phone and remove everything from startup folder .. my phone boots .. and i can see start botton .. no touch alignment comes .. and everything works .. but.. screen is virtually reversed .. i can see the OK botton but i must click on the facing area and it be clicked ..
i think i executed some wrong hard SPL to my phone ant that happened >
is there any way to resolve this problem?
is there any way to erase flash on my I-Mate Jam????
is there any way flash my phone?
i also have prepaid JAFWM with pkey and USB cable .. no BOX ..
Help please!
that's messed up... howsabout flashing it at the point when the phone boots up? if there's an AS connection there, then it may work... i'd flash to an official rom though
Same problem , PLS Help !!!
Thx for help
You should check USB connection I think...
Try plug your battery out of device and wait a moment (e.g.10 minutes) and try again,sometimes it will be fine when you did this.
If your magician isn't detected at ALL by your PC when plugging the USB cable into it (i mean, no new hardware; no unrecognized hardware; nothing is detected in your PC when you plug the USB cable), and unless you had previously made a SD backup of your entire Flash with this procedure ( http://wiki.xda-developers.com/index.php?pagename=MagicianSDflash ), then your only option will be to build a JTAG diag cable:
Here are some general directions / ideias:
Magician JTAG pinout: http://wiki.xda-developers.com/index.php?pagename=MagicianJTAG
How to build/run the JTAG: http://wiki.xda-developers.com/index.php?pagename=DeadBoot
Photos : http://www.cf-box.com/htm_data/55/0912/1679.html
Some interesting stuff for debugging problems: http://pda2u.ru/ptopic205.html
For sure cotulla has one built so to test his ROMs + bootloader - maybe he will be willing to give you some directions if you run into problems, and above all, give you a prepared .nb0 (with the bootloader file) for your magician, which i do not know if there's one out there, extracted from an original ROM.
Anyway, you can always try and do it for yourself using itsme utilities. Follow this link: http://forum.xda-developers.com/showthread.php?t=218643
Regards
Keeper,you're awesome! I'm searching for JTAG,too
xiaojin1985 said:
You should check USB connection I think...
Try plug your battery out of device and wait a moment (e.g.10 minutes) and try again,sometimes it will be fine when you did this.
Click to expand...
Click to collapse
Dear xiaojin1985 ,
Thx for your help, But unfortunately i tried your solution but it dosnt work !
Dear Keeper,
Thanks too for your help,
and i think the solution for my problem is one of the solutions you says ( How to build/run the JTAG: ) ,
but the pictures is not available anymore , so pls can you get the pictures ?
All the pictures are in here:
http://s218.photobucket.com/albums/cc23/alex_beda/ and in attachment there's a .mth file with all the pics built-in.
Don't take it wrong what i'm about to say, but in all honesty if you can't figure this out yourself (digging up the internet for the missing pics), i would suggest that you shouldn't try this, since this ain't easy at ALL...
Just to give you some ideias, it will require you to adapt your magician test point signals (TDO;TDI; nRESET; etc,)seen on the magician pinout pic to what is said; solder very thin wires (best done with a small hot air tip); fixate the small dip switch (micro switch) to be always on; keep the USB connected...idk... plus alot of other small details which ain't easy to accomplish.
Personally i haven't tried this yet but for sure it would work
If you decide to go ahead, please post some results!
Connection error solution
this is my problem
hi all. A friend of mine gave me an S100, and after i played for a few days with it, i decided to update it's rom. A "country error" problem appeared,cause i have the greek version, so i ran MaUpgradeUt_noID.exe which completed (as showed 100% process). My (new) problem is that i cannot update anymore. Every time i enter boot menu, i ran the upgrade
(HTCMAG_ROM_WWE_O2.rar) following all the steps normally. When the device resets (so the upgrade is going to start), it's re-reseting again and showing ERROR 101 connection error. Any ideas?
Qtek Greek version
R 1.12.00
G 1337.42
D 1.12.00 WWE
P.S. apart the problem everything is function properly
and the solution
hard reset
plug usb (uncheck allow usb connection in activesynch )
run MaUpgradeUt.exe radio_1.11_greek but idont reset the qtek in first screen
and upgrate downgrate start all ok
reset
welcome screen
hard reset
plug usb (uncheck allow usb connection in activesynch )
run MaUpgradeUt.exe MagicianRadio_1.12.10. uk but idont reset the qteki n first screen
upgrate from radio 1.11 to 1.12.10
reset
welcome screen
hard reset
plug usb (uncheck allow usb connection in activesynch )
run HTCMAG_ROM_WWE_O5_251209
everything is ok my magisian run the new Rom
here..........................
Hi Help me pls,
I've tried to flash my rom via ActiveSync. Every thing went well until i get the progress bar then it got stuck at 0% for ages so i disconnect the whole thing and tried to restart the process.
NOW I CAN'T ACTIVESYNC ANYMORE !!!! but the connection as "memory card reader" still working.
I went through all the post and tried to flash the ROM via bootloader with the "RAPHIMG.nbh" in my SD card ( already formated FAT32 ) but every time the PDA got stuck at the first stage "loading".
HELP ME PLEASE
I have similar problem, can't connect to PC anymore, but flashing with SD card works for me
have you tried different ROM images?
TQY said:
Hi Help me pls,
I've tried to flash my rom via ActiveSync. Every thing went well until i get the progress bar then it got stuck at 0% for ages so i disconnect the whole thing and tried to restart the process.
NOW I CAN'T ACTIVESYNC ANYMORE !!!! but the connection as "memory card reader" still working.
I went through all the post and tried to flash the ROM via bootloader with the "RAPHIMG.nbh" in my SD card ( already formated FAT32 ) but every time the PDA got stuck at the first stage "loading".
HELP ME PLEASE
Click to expand...
Click to collapse
It sounds like you did not carefully read this.
That is also where this should have been posted. A new thread should not be started for this type of issue. I understand you are panicing. However, in almost all situations the phone can be recovered.
That said, Hold volume down and hit the reset button. It will put you in the tricolor screen. In the white it says serial. Connect it to your usb cord. It should now say usb. Now flash the STOCK rom.
be sure that battery over 50% then follow arupphental's
I have a friend with a kaiser and the same problem. can this be applied to it? i dont want to search through the forum forever...
I would start by going to the kaiser forums and checking the stickies. Search within the kaiser forum also works.
I have This problem on Vista OS, i connect my touch pro after reboot system, and if i disconnect device and try again connect, my system not see device!
On device manager in OS, my touch pro stay present after disconnect device. This problem retry if after connect i try flash rom on device, black screen on and flashing stop with error connect to device.
Please Help!!!!!
P.S. Sorry my Bad English
X2D said:
I would start by going to the kaiser forums and checking the stickies. Search within the kaiser forum also works.
Click to expand...
Click to collapse
ok i thought someone would say that. was just wondering off hand. thanks x2d
A.creature said:
I have This problem on Vista OS, i connect my touch pro after reboot system, and if i disconnect device and try again connect, my system not see device!
On device manager in OS, my touch pro stay present after disconnect device. This problem retry if after connect i try flash rom on device, black screen on and flashing stop with error connect to device.
Please Help!!!!!
P.S. Sorry my Bad English
Click to expand...
Click to collapse
go to bootloader (tricolor on screen)& flash a rom, your PPC 'll be fine. when you flash ROM, PC transfer data through USB to PPC therefor not need connect by activesync.
I had the same problem after a faulty ROM from Vodafone NL, what I had to do is before I wanted to flash my ROM do a hard reset on my device (please back-up your personal data before doing this). After the hard reset, I could get a stable connection with activesync and flash my ROM
While the circumstances are different, my advice is still the same: http://forum.xda-developers.com/showthread.php?t=481527
longnguyen30 said:
go to bootloader (tricolor on screen)& flash a rom, your PPC 'll be fine. when you flash ROM, PC transfer data through USB to PPC therefor not need connect by activesync.
Click to expand...
Click to collapse
Stumbled upon this.. and yes the advise is good, when you run the flashing utility (i.e. CustomRUU.exe), it says you need an Active Sync connection, but you really dont, you can flash it anyway, it seems to find the device via USB regardless.
ufff!!!! to me yes found right, thank you thank you to first post. (flashing from SD)
Undetected
Well i had the problem where my phone wasnt getting detected at all.... i put the stock rom and radio but couldnt put stock spl on the phone with sdcard.... after trying different computers/usb wires/settings i returned it for a new one and this one works fine.
Hello guys
last week my Tytn II decide to also get stuck at the bootscreen. It had been running more than a year with one of Dutty's ROMs without any problems at all. Fortunately I knew this forum so I didn't really panic but started reading possible solutions to the problem.
Flashing new OS or SPL via USB didn't work. Nor was I able to connect via mtty to give the boot command. I finally got it back working by flashing KAISDIAG.NBH and after that flashing RUU-356-patch-nostuckinSPL-FORCEUSB as KAISIMG.NBH both via the SD method. After that I have downloaded and flashed the latest standard HTC rom & radio. The device boots and can make calls.
However whenever it is connected to a pc it just freezes. Or at least becomes so slow there's nothing that can be done with it. Activesync connection cannot be established. Note, this does not happen if the device is connected to my car charger or to another USB charger, but only when connected to a PC, XP or vista, doesn't matter.
I've tried flashing different boot loaders, OSes & radios, so far no luck. Currently OS = 3.34.721.2 WWE & Radio i= 1.65.24.36.
Booting & making calls works, connecting via activsync doesn't.
I'd appreciate it if anyone could give me some tips as to what could be the cause of this problem.
Anyone got any ideas as to what I could do?