Hello guys
last week my Tytn II decide to also get stuck at the bootscreen. It had been running more than a year with one of Dutty's ROMs without any problems at all. Fortunately I knew this forum so I didn't really panic but started reading possible solutions to the problem.
Flashing new OS or SPL via USB didn't work. Nor was I able to connect via mtty to give the boot command. I finally got it back working by flashing KAISDIAG.NBH and after that flashing RUU-356-patch-nostuckinSPL-FORCEUSB as KAISIMG.NBH both via the SD method. After that I have downloaded and flashed the latest standard HTC rom & radio. The device boots and can make calls.
However whenever it is connected to a pc it just freezes. Or at least becomes so slow there's nothing that can be done with it. Activesync connection cannot be established. Note, this does not happen if the device is connected to my car charger or to another USB charger, but only when connected to a PC, XP or vista, doesn't matter.
I've tried flashing different boot loaders, OSes & radios, so far no luck. Currently OS = 3.34.721.2 WWE & Radio i= 1.65.24.36.
Booting & making calls works, connecting via activsync doesn't.
I'd appreciate it if anyone could give me some tips as to what could be the cause of this problem.
Anyone got any ideas as to what I could do?
Related
Hi,
I have tryed to upgrade my rom to a new version (Prophet WM5 AKU3.2 v3231). Followed the stept correctly, however my phone does not boot anymore. It gets stuck in the qtek logo (when it displays the AKU version i´ve got) and the sceen gets all shacky.
An addictional problem is because it is stuck at that point it does not connect to my computer....
What can I do to fix this, any good suggestions
Thank,
Sebastiaan
You should be able to enter bootloader mode by pressing and holding the camera button while you power on your phone. On the bottom left, you should then see "USB" - connect it to the PC and flash it again.
Had to do this yesterday after flashing failed.
Mike
thanks it worked
Sebastiaan
Error [296] Upgrade Only
Hello
I have same Trouble & I Make Bootloder from USB but Always I get This Error
ERROR [296] UPGRADE ONLY
This NBF file connects used for your PDA Phone. Please get newer NBF file.
Note: I try to Upgrade to 2006-11-12_Prophet_WM5AKU2.3_lvsw_edition but my Phone Stack So I reset as say after 30 m
Now I trying to back to Old Software from I-mate
Also I try to upgrade to 2006-11-12_Prophet_WM5AKU2.3_lvsw_edition but no Connection....
Please help me I with out Live (Phone)
I know it sounds strange but i used a different USB port and then it did connect. Now that everything is back to normal i can use the old one again.
maybe it works for you as well
I tried doing that, but for some reason my computer doen't recognize the device...pls help!
Hi guys,
can someone help me ?
I want to flash my XDA Neo with a new ROM (WM6)
However,
I have successfully connected my Phone with ActiveSync 4.5 on WinXP SP2
Then I run an RUU Utility.
The Phone goes into Bootloader (RGB Screen) and then the connection is lost.
From then I couldn't etablish a connection to the Phone.
Is there another way to flash the ROM of my Phone ? e.g. from SD Card directly ?
Any help appreciated - thx
Flashx4u said:
Hi guys,
can someone help me ?
I want to flash my XDA Neo with a new ROM (WM6)
However,
I have successfully connected my Phone with ActiveSync 4.5 on WinXP SP2
Then I run an RUU Utility.
The Phone goes into Bootloader (RGB Screen) and then the connection is lost.
From then I couldn't etablish a connection to the Phone.
Is there another way to flash the ROM of my Phone ? e.g. from SD Card directly ?
Any help appreciated - thx
Click to expand...
Click to collapse
I would join to this question - I have the same problem: somewhere in the middle of flashing my Prophet with Prophet_PV_Temp my Prophet started a dead-cycle with connecting-disconnecting...And I can not reflash it. Now I also have Bootloader (RGB screen) which is on when Prophet is not connected to PC and when I connect it to PC, it disconnects-reconnects-disconnects-reconnects-......
What is the solution?
The problem SOLVED!
ZRimaZ said:
I would join to this question - I have the same problem: somewhere in the middle of flashing my Prophet with Prophet_PV_Temp my Prophet started a dead-cycle with connecting-disconnecting...And I can not reflash it. Now I also have Bootloader (RGB screen) which is on when Prophet is not connected to PC and when I connect it to PC, it disconnects-reconnects-disconnects-reconnects-......
What is the solution?
Click to expand...
Click to collapse
So ,finally I found the solution with this issue and problem with my Prophet's restarting after it's registering to the cellular network (I wrote about it in another treeds as well).
After I tried to reflash my Prophet with different WM6 ROMs, different Radio ROMs, reassembled and cleaned it, reflashed to original WM5 ROM and nothing helped, I just came to an idee to replace the battery, unless Prophet indicated that still it's a lot of power (min 50%)...I ordered the battery and when I received it and replaced, everything is running as it should be!!!!
Ok earlier i was trying to extraact the dk.01 rom i ran kasier kitchen extracted the nbh file. Then i used the folders to cook a new rom and didnt include any packages at all. So when i flashed this rom to the phone something went horribly wrong the phone stuck on the splash screen where it lists the rom radio and protocall version. Anyways i got mtty 1.42 and it doesnt have usb in the options Im using vista and niether wsecomm or the other process is running i even went to windows mobility center and turned usb off. then rebooted my computer. Tried two diffrent usb cables, the pc isnt even seeing a usb device connected to it. Is my tilt toast? Can i get away with telling the at&t insurance i lost the phone?
Sorry guys issue resolved i just help camera power and reset and it loaded hard spl.
problem solved
Hi Help me pls,
I've tried to flash my rom via ActiveSync. Every thing went well until i get the progress bar then it got stuck at 0% for ages so i disconnect the whole thing and tried to restart the process.
NOW I CAN'T ACTIVESYNC ANYMORE !!!! but the connection as "memory card reader" still working.
I went through all the post and tried to flash the ROM via bootloader with the "RAPHIMG.nbh" in my SD card ( already formated FAT32 ) but every time the PDA got stuck at the first stage "loading".
HELP ME PLEASE
I have similar problem, can't connect to PC anymore, but flashing with SD card works for me
have you tried different ROM images?
TQY said:
Hi Help me pls,
I've tried to flash my rom via ActiveSync. Every thing went well until i get the progress bar then it got stuck at 0% for ages so i disconnect the whole thing and tried to restart the process.
NOW I CAN'T ACTIVESYNC ANYMORE !!!! but the connection as "memory card reader" still working.
I went through all the post and tried to flash the ROM via bootloader with the "RAPHIMG.nbh" in my SD card ( already formated FAT32 ) but every time the PDA got stuck at the first stage "loading".
HELP ME PLEASE
Click to expand...
Click to collapse
It sounds like you did not carefully read this.
That is also where this should have been posted. A new thread should not be started for this type of issue. I understand you are panicing. However, in almost all situations the phone can be recovered.
That said, Hold volume down and hit the reset button. It will put you in the tricolor screen. In the white it says serial. Connect it to your usb cord. It should now say usb. Now flash the STOCK rom.
be sure that battery over 50% then follow arupphental's
I have a friend with a kaiser and the same problem. can this be applied to it? i dont want to search through the forum forever...
I would start by going to the kaiser forums and checking the stickies. Search within the kaiser forum also works.
I have This problem on Vista OS, i connect my touch pro after reboot system, and if i disconnect device and try again connect, my system not see device!
On device manager in OS, my touch pro stay present after disconnect device. This problem retry if after connect i try flash rom on device, black screen on and flashing stop with error connect to device.
Please Help!!!!!
P.S. Sorry my Bad English
X2D said:
I would start by going to the kaiser forums and checking the stickies. Search within the kaiser forum also works.
Click to expand...
Click to collapse
ok i thought someone would say that. was just wondering off hand. thanks x2d
A.creature said:
I have This problem on Vista OS, i connect my touch pro after reboot system, and if i disconnect device and try again connect, my system not see device!
On device manager in OS, my touch pro stay present after disconnect device. This problem retry if after connect i try flash rom on device, black screen on and flashing stop with error connect to device.
Please Help!!!!!
P.S. Sorry my Bad English
Click to expand...
Click to collapse
go to bootloader (tricolor on screen)& flash a rom, your PPC 'll be fine. when you flash ROM, PC transfer data through USB to PPC therefor not need connect by activesync.
I had the same problem after a faulty ROM from Vodafone NL, what I had to do is before I wanted to flash my ROM do a hard reset on my device (please back-up your personal data before doing this). After the hard reset, I could get a stable connection with activesync and flash my ROM
While the circumstances are different, my advice is still the same: http://forum.xda-developers.com/showthread.php?t=481527
longnguyen30 said:
go to bootloader (tricolor on screen)& flash a rom, your PPC 'll be fine. when you flash ROM, PC transfer data through USB to PPC therefor not need connect by activesync.
Click to expand...
Click to collapse
Stumbled upon this.. and yes the advise is good, when you run the flashing utility (i.e. CustomRUU.exe), it says you need an Active Sync connection, but you really dont, you can flash it anyway, it seems to find the device via USB regardless.
ufff!!!! to me yes found right, thank you thank you to first post. (flashing from SD)
Undetected
Well i had the problem where my phone wasnt getting detected at all.... i put the stock rom and radio but couldnt put stock spl on the phone with sdcard.... after trying different computers/usb wires/settings i returned it for a new one and this one works fine.
I finally got connect between my HTC Touch Pro and OSX (parallels + Activesync)
I am trying to run RaphaelHardSPL-Unsigned_190_1_3 and everything goes well, but when it trys to connect to the device to start the mod, i get Error [202] Connection. I have tried enabling/disabling Advaned Network Funtionality in Connection settings, but that did not help. I have tried manually going into bootloader (when the transfer is about to start, I hold VolDown, and reset, and wait for Bootloader to go into USB mode). That didn't work for me.
My question(s) are, how can I get the HardSPL running, or how can I get my deviced flashed in general (SD method didn't work)
AND: My version in HARDSPL is stated to be 1.95.502.5. Is it OK if I downgrade to 1.90.1.3 in order to allow custom ROMs?
Thanks in advance.
Parallels doesn't play nice with the USB bridge.
Try boot-camp (works for me).
I crashed my first Kaiser, flashing with Parallels. Couldn't recover it after the usb connection cut out mid flash. I sent it in for warranty exchange, telling them it crashed while doing an " official " rom update. luckily no one looked too close and they sent me a replacement.
Now I only use Bootcamp and xp. And after more flashes than I can count, I have never had a problem.