I have flashed dutty's v4 rom and i want to change it
the problem is that when i try to do so i run
KaiserCustomRUU
my device goes into the 4 stripes screen it says usb
but then the program in the pc says error 260 and doesn't load the new rom
my phone still works as dutty's rom is still in but what can i do to change it?
Thank you and i have searched a lot but could not find a solution
thimiost said:
I have flashed dutty's v4 rom and i want to change it
the problem is that when i try to do so i run
KaiserCustomRUU
my device goes into the 4 stripes screen it says usb
but then the program in the pc says error 260 and doesn't load the new rom
my phone still works as dutty's rom is still in but what can i do to change it?
Thank you and i have searched a lot but could not find a solution
Click to expand...
Click to collapse
OK lets start at the basics...... In bootloader mode (tricolour screen) what text does it say at top of the screen?
Have you DEFINITELY Sim Unlocked and CID unlocked?
it says these things
kais130 mfg
spl-10.0.Olipof
cpld-8
Ok that confirms you have the capability to flash. I have seen in the past some people have managed to flash one time only using jumpspl but then their device reverts back to original bootloader...I was one of those people
Next question then...Can you boot the phone normally and gain an activsync connection to it?
yes
i can use my phone normally
only i cannot put a new image in
Are you using Xp or vista? If using vista it may be worth trying a reboot... sometimes it goes doolally with its usb ports. If you cannot see the phone through WMDC or activsync after a reboot it is worth going to SYSTEM (on your PC) viewing non present devices through device manager,( Drop to Command prompt and type... Devmgmt.msc set DEVMGR_SHOW_NONPRESENT_DEVICES=1 ) removing the relevant phone connection and then re attaching it so that windows re detects it.
If you can get a connection via actvisync (win XP) or WMDC (vista) to your phone then all should be ok. Uncheck the activesync/ WMDC "allow USB connections" and try again.
If this still doesn't work then search around here for MTTY. That will allow you to specify the usb connection to the device...amongst other things.
thank you for your time
i have win xp and activesync works nice
the problem is when bootloader starts
When you attempt flashing, do you do it from the device already booted into windows mobile or direct from bootloader?
Which ever way you have tried it, try ther other way.
Not teaching you to suck eggs but just in case you dont know.... To get direct to bootloader hold camera button and soft reset with stylus whilst holding camera button down and the tri colour screen should appear.
With device at the bootloader screen, Can you confirm that you hear the windows "noise" when you unplug and re plug the USB cable just as you would when plugging and unplugging the device normally. This will determine if the device has connection at the bootlaoder stage.
why not just flash using the microsd card. its much easier that way
yes it has connection
the thing is that i have already flashed as i told before with dutty's v4
now i can't
Usually Error 260's are related to the USB port functionality ( Port can't be opened etc).
The SD card method or MTTY should sort you out.
thx again
hope it works
at least the sd trick worked!!!!
now running on winmob 6.1
Glad to hear you sorted it.
almost
i cannot use my sd card cause i have to have it formated in order to put a new rom in
thimiost said:
i cannot use my sd card cause i have to have it formated in order to put a new rom in
Click to expand...
Click to collapse
disable USB connections in ActiveSync and flash.
This Link gives a list of eror codes for Hermes, and probably the same for Kaiser.
It's likely that you have a USB port error - maybe try changing the USB port you use or a different sync cable - or just stick to SD card flashing in the future - I keep an old 1gig card for this.
this IS the problem...i cannot flash...
it stays in the bootloader with the message i wrote
thimiost said:
it stays in the bootloader with the message i wrote
Click to expand...
Click to collapse
It happen to me before hardspl again fix it, not sure why
you mean use the sd method to do hardspl again?
OHHH lord dutty we need your new rom
Related
Hi All,
Out of the blue my HTC Vox stopped booting. I mean, it would load to the windows mobile screen and then stay there till eternity. Removing my memory card and SIM also did not help! I then tried the hard reset option.
Even after hard reset it sometimes boots(1 out of 15 times) and when it does...it hangs after 10 to 12 minutes. Still have not put my sim n memory card into the phone.
I tries flashing the ROM using the ARA 1.27 ROM. After it rebooted to the bootloader, the flash utility gave a connection error! It did not connect to ActiveSync and stayed at the bootloader screen.
I still do not know how to flash it successfully.
If anybody can help me out, I'll be extremely grateful!
Thanks
Prateek
take the battery out, put it back.
connect your Vox (USB).
Hold the camera button and turn on your Vox.
you should see a red, blue and green screen (if my memory works as it should) and the computer should recognize the device, though you won't be able to explore it with activesync.
Run the SDA_ApplicationUnlock thingy (if you need to)
now try flashing the device.
If it flashes but after 3% restart, you need to do a CID unlock right before flashing.
hope that helps.
Invalid Vendor ID
Hi MoRkusReX,
Its giving me Invalid Vendor ID. How do I CID unlock it?
Thanks,
Prateek
http://forum.xda-developers.com/showthread.php?t=330909
first post , download the last file:
Vox USPL- CID BYPASS.zip
There a Readme file in there, you should read it.
post back where you're done.
No Luck!
Hi MoRkusReX,
Since my phone is not booting into the OS thus I cannot use the UPSL_CID provided in the link.
Only once I have been able to boot into my OS and followed the instructions given in the link. The phone comes to the Linux black screen and then switchers off. Then the ROM Update Utility with which i'm trying to update the ROM gives an error that "cannot connect to the phone".
So, now I need to flash my ROM from the bootloader itself. Have managed to get mtty and connect to the phone. But even trying ResetDevice command, the phone does not boot.
Can you tell me the exact steps to flash a new ROM from the bootloader itself including CID unlocking? Can it be done??
Thanks,
Prateek
prateekswarup said:
Hi MoRkusReX,
Since my phone is not booting into the OS thus I cannot use the UPSL_CID provided in the link.
...
including CID unlocking? Can it be done??
Thanks,
Prateek
Click to expand...
Click to collapse
yes it can be done.
you don't need to boot to OS, I couldn't either. after the steps from my first post here, run the uspl_116_jockyw.bat file. follow instructions.
that will unlock the CID.
Now the VOXs' screen should be white or so... then you run the ROM update thingy.
Hi..
I connected with the usb and got the bootloader screen.
tried running the SDA unlock program...the button to unlock the phone is grayed out. Cant click on it.
Next tried running uspl_116_jockyw.bat file
..cannot connect to phone and hence copy of haret.exe did not occur and neither did pmemtest run successfully...
What am I doing wrong??
ok..
first steps again..
battery out, back in.
connect USB
CAMERA button + Turn on.
now.. does windows do that USB sound? you know.. "tu du" ?
No sound....using win 2k Nt server edition...
but has detected my phone once on that USB and then allows me to talk to the phone using mtty....as in commands like ResetDevice work on the phone using mtty..
also, cannot get into bootlaoder mode with USB plugged in...
Steps and their results:
Disabled USB connections in activesync
Booted to the bootloader (red and green and Blue screen)
Connected the USB
"USB" displays on the left hand side corner
Now tried unlocking using Apllication unlock...grayed out button...
Tried running USPL bat but stops and says phone not connected when copying haret.exe
Using windows NT server 2003
if the SDA Application unlock button is grayed, of course the USPL won't work.
why "Disabled USB connections in activesync"?
And.. I doubt this is the problem but you should check on an winXP pc, I did it on XP.
No Luck!
Tried the same with USB enabled...same result
basically the thing we need to figure out is why your computer doesn't recognize the device.
the rest is obvious.
when I go to bootloader on my device windows pops up with a message says windows found device "and it's ready to use". like when you cannot every other USB item.
have you tried doing that on an XP system?
Going to do that now....lets hope it works....
Does ur activesync turn green when u connect at bootloader?
Also, I have removed my sim and memory card...thats okay right?
yeah, I removed both of them.
and no, activesync didn't turn green, but Windows recognized the device when I turned it on. turn on the speakers and wait for that winxp "USB connected" sound.
Still No Luck!
Tried doing the same on win xp...
no luck...
it connects to win xp ans says new device found...and ur USB device is now
ready to use...
after that i try application unlock it still gives me grayed out button....
ne suggestions???
Finally....
Finally got it done...
Thanks for all the help....
I managed to cold boot into the system for one time ans then SDA unlocked it and then ran UPSL .... it ran and then balnked out...
then i disconnected the usb before the ROM update utility and unchecked the USB option in active sync...
then i flashed it with the ARA rom...
Seems to be working okay now..will test for a day and see...
thanks a lot
prateek
prateekswarup said:
Finally got it done...
then i disconnected the usb before the ROM update utility and unchecked the USB option in active sync...
prateek
Click to expand...
Click to collapse
I'm not sure this step was necessary but as long as it worked.. good times.
btw, how did you boot into the system?
kept trying hard reset and repeated booting...( it was booting 1 in 15 times type...)..and one lucky time it didnt hang..so used that window to slip in the SDA unlock and USPL..
thanks ...
you're welcome.
Hello,
I'm realy going insane at the moment.
I try to degrade the SPL from SPL-1.0.OliPof (KAIS130 MFG, CPLD-8 <- whatever that means) back to the orginal one.
What I'm doing is:
1. connect the kaiser without sd card and sim card via active sync to my XP PC.
2. start the bootloader via button and stylus.
3. unplug the usb cable and replug
4. starting the KaiserCustomRUU tool.
the problem is that I always get an error 260 which means that there is no connection between pc and pda. by the way I already tried every possible solution mentioned in this forum.
What i figured out is that after I repluged the usb cable the computer detects the pda but is not able to install a suitable driver. So I have an unrecognized usb device in the device manager. I guess this is the issue but does anybody know how to solve it. I mean which driver is needed in this state?
can anybody help?
greetings,
macx
I must be misreading your post... you don't mention running JumpSPL/SSPL. If you're not doing that, then there's you freebie for the year, and also the solution to your problem.
sorry, my fault.
Point 2 is running SSPL of course. Version 1 leads to a white screen and the other two versions bring up the bootloader.
In the meanwhile I tried so many things that I was a bit confused when I wrote this post.
nevertheless I don't know what to do anymore to make it work.
Hi Help me pls,
I've tried to flash my rom via ActiveSync. Every thing went well until i get the progress bar then it got stuck at 0% for ages so i disconnect the whole thing and tried to restart the process.
NOW I CAN'T ACTIVESYNC ANYMORE !!!! but the connection as "memory card reader" still working.
I went through all the post and tried to flash the ROM via bootloader with the "RAPHIMG.nbh" in my SD card ( already formated FAT32 ) but every time the PDA got stuck at the first stage "loading".
HELP ME PLEASE
I have similar problem, can't connect to PC anymore, but flashing with SD card works for me
have you tried different ROM images?
TQY said:
Hi Help me pls,
I've tried to flash my rom via ActiveSync. Every thing went well until i get the progress bar then it got stuck at 0% for ages so i disconnect the whole thing and tried to restart the process.
NOW I CAN'T ACTIVESYNC ANYMORE !!!! but the connection as "memory card reader" still working.
I went through all the post and tried to flash the ROM via bootloader with the "RAPHIMG.nbh" in my SD card ( already formated FAT32 ) but every time the PDA got stuck at the first stage "loading".
HELP ME PLEASE
Click to expand...
Click to collapse
It sounds like you did not carefully read this.
That is also where this should have been posted. A new thread should not be started for this type of issue. I understand you are panicing. However, in almost all situations the phone can be recovered.
That said, Hold volume down and hit the reset button. It will put you in the tricolor screen. In the white it says serial. Connect it to your usb cord. It should now say usb. Now flash the STOCK rom.
be sure that battery over 50% then follow arupphental's
I have a friend with a kaiser and the same problem. can this be applied to it? i dont want to search through the forum forever...
I would start by going to the kaiser forums and checking the stickies. Search within the kaiser forum also works.
I have This problem on Vista OS, i connect my touch pro after reboot system, and if i disconnect device and try again connect, my system not see device!
On device manager in OS, my touch pro stay present after disconnect device. This problem retry if after connect i try flash rom on device, black screen on and flashing stop with error connect to device.
Please Help!!!!!
P.S. Sorry my Bad English
X2D said:
I would start by going to the kaiser forums and checking the stickies. Search within the kaiser forum also works.
Click to expand...
Click to collapse
ok i thought someone would say that. was just wondering off hand. thanks x2d
A.creature said:
I have This problem on Vista OS, i connect my touch pro after reboot system, and if i disconnect device and try again connect, my system not see device!
On device manager in OS, my touch pro stay present after disconnect device. This problem retry if after connect i try flash rom on device, black screen on and flashing stop with error connect to device.
Please Help!!!!!
P.S. Sorry my Bad English
Click to expand...
Click to collapse
go to bootloader (tricolor on screen)& flash a rom, your PPC 'll be fine. when you flash ROM, PC transfer data through USB to PPC therefor not need connect by activesync.
I had the same problem after a faulty ROM from Vodafone NL, what I had to do is before I wanted to flash my ROM do a hard reset on my device (please back-up your personal data before doing this). After the hard reset, I could get a stable connection with activesync and flash my ROM
While the circumstances are different, my advice is still the same: http://forum.xda-developers.com/showthread.php?t=481527
longnguyen30 said:
go to bootloader (tricolor on screen)& flash a rom, your PPC 'll be fine. when you flash ROM, PC transfer data through USB to PPC therefor not need connect by activesync.
Click to expand...
Click to collapse
Stumbled upon this.. and yes the advise is good, when you run the flashing utility (i.e. CustomRUU.exe), it says you need an Active Sync connection, but you really dont, you can flash it anyway, it seems to find the device via USB regardless.
ufff!!!! to me yes found right, thank you thank you to first post. (flashing from SD)
Undetected
Well i had the problem where my phone wasnt getting detected at all.... i put the stock rom and radio but couldnt put stock spl on the phone with sdcard.... after trying different computers/usb wires/settings i returned it for a new one and this one works fine.
My Dear Samaritans,
IMPORTANT:
- My SD/Memory card is removed
- My Sim card is removed
I was upgrading to Tomal v8.9 on a vista 64 system via a virtual machine XP SP2. Update failed and I got stuck in bootloader.
Tried reflashing but got an error and the flash failed... also the program crashed during recovery.
Tried using v8.71 still crashed without any luck.
Moved to a pure XP SP3 desktop...
When I connect the device to the computer(s) "Serial" changes to "USB" but XP sees it as an unrecognized device.
Tried flashing again but same error as on the virtual machine.
Tried mtty (1.16 & 1.42) but neither give me the option of USB, only COM1 and COM2. And had already de-activated the USB connection in Activesync.
Have read through the forum but have had no luck. Everyone's issue is resolved as soon as they remove their SD or SIM, but I have neither and am also using XP with activesync's USB disabled.
Tried UNI_ExitBootloader but that does not find/recognise the device either.
If it helps -- My device is/was an O2 XDA Exec (Stock) which I had previously flashed with Tomal's v8.5
I am ready to try anything, please help!
P.S: The error is Error 112
Did you install ActiveSync on xp pc?
If not, do it now and try again.
I had similar problem. Had corrupted DOC sector
and MTTY was the only solution, but although the Serial changed to USB, I got 'unrecognised' message and Mtty didn't give USB as an option. At some point it occured to me that it was my computer's USB port, for some reason the device was recognised by 1 in 4 ports only, So I just tried my USB cable in different ports until the 'device unrecognised' messaged stopped appearing. Finally, after I was ready to cry in frustration, it just worked. Don't give up.
I heard it mentioned somewhere that the device that went through Mtty will be recognised only by the port used in Mtty procedure.
That... or your device's USB is no longer properly attached to the mainboard.
tomal said:
Did you install ActiveSync on xp pc?
If not, do it now and try again.
Click to expand...
Click to collapse
Already have activesync 4.5 installed with USB connection disabled...
Thank you so much for the prompt response and helpful thought!
enigma1nz said:
and MTTY was the only solution, but although the Serial changed to USB, I got 'unrecognised' message and Mtty didn't give USB as an option. At some point it occured to me that it was my computer's USB port, for some reason the device was recognised by 1 in 4 ports only, So I just tried my USB cable in different ports until the 'device unrecognised' messaged stopped appearing. Finally, after I was ready to cry in frustration, it just worked. Don't give up.
I heard it mentioned somewhere that the device that went through Mtty will be recognised only by the port used in Mtty procedure.
That... or your device's USB is no longer properly attached to the mainboard.
Click to expand...
Click to collapse
Thank you for the ray of hope! Will keep trying every hourly reboot in every USB port (4 in all).
Weird thing is I never had to go through mtty before so this is my first need for it.
Got the physical connection checked and it is supposedly OK...
Thank you for the prompt help...
Don't worry
I had exactly the same problem. First I tried this and it worked but still no connection via mtty. On that evening I disconnected and connected a lot and I removed the battery for a long time (one night). Later I could connect but I don't know why. Maybe these two things were the solution. Mtty showed "usb>" and I've done a DOC format...
If nothing works I would create a rom-image (on sunday or monday) for your sd-card like it's written in the service manual.
blingin said:
Thank you for the ray of hope! Will keep trying every hourly reboot in every USB port (4 in all).
Weird thing is I never had to go through mtty before so this is my first need for it.
Got the physical connection checked and it is supposedly OK...
Thank you for the prompt help...
Click to expand...
Click to collapse
No need for hourly reboots, just get into Bootloader, connect USB to your device and try different ports on computer with a few seconds in between to ensure no 'unrecognised device' message popping up. Once you'll get a connection - go for Mtty facility, the USB is the last on the list of ports.
330e said:
I had exactly the same problem. First I tried this and it worked but still no connection via mtty. On that evening I disconnected and connected a lot and I removed the battery for a long time (one night). Later I could connect but I don't know why. Maybe these two things were the solution. Mtty showed "usb>" and I've done a DOC format...
If nothing works I would create a rom-image (on sunday or monday) for your sd-card like it's written in the service manual.
Click to expand...
Click to collapse
There was no SD card when I began the initial flash but it still got stuck. Been trying without the SD and SIM but to no avail...
Thank you for the manual, downloading it now, will keep everyone posted in case anyone else is suffering from the same thing...
enigma1nz said:
No need for hourly reboots, just get into Bootloader, connect USB to your device and try different ports on computer with a few seconds in between to ensure no 'unrecognised device' message popping up. Once you'll get a connection - go for Mtty facility, the USB is the last on the list of ports.
Click to expand...
Click to collapse
Still trying, will keep you posted and thank you for the responses!
I think you understood me wrong. When your device is still unusable, I would create the files you need to do the steps in point 8.3 (Use Pre-loaded SD card to Re-flash Unit) in the service manual.
Sorry for my bad english
330e said:
I think you understood me wrong. When your device is still unusable, I would create the files you need to do the steps in point 8.3 (Use Pre-loaded SD card to Re-flash Unit) in the service manual.
Sorry for my bad english
Click to expand...
Click to collapse
It's the thought that counts not the language, thank you so much for your help!
I created succesfully a pre-loaded sd card, flashing via this sd works. But I can't copy the files. When I want to open the drive it says, that I have to format the sd card. Is there a special tool to copy the files? Or you find someone near you with a universal.
your need to format your SD after flashing.
330e said:
I created succesfully a pre-loaded sd card, flashing via this sd works. But I can't copy the files. When I want to open the drive it says, that I have to format the sd card. Is there a special tool to copy the files? Or you find someone near you with a universal.
Click to expand...
Click to collapse
tomal said:
your need to format your SD after flashing.
Click to expand...
Click to collapse
Tried the SD image method with a 128MB SD but didn't work. Maybe because I have a G4 and the method is for G3
managed to get a connection finally and ran MTTY, after "task28 55a" it just hung for a long time so I disconnected.
Tried running UNI_ExitBootloader.exe and now can get in and out of Bootloader but still cannot flash or connect...
Any suggestions welcome...
Try this....
This might sound silly but it's worked for me in the past.
1. Go into bootloader (without mem card or sim)
2. Plug-in the USB cable
3. Hold the buttons to go into bootloader again whilst plugged in.
4. DOC Format
5. Flash ROM
My Universal had loads of problems but that is how i fixed it, tried everything else like you, when i first plugged it in on the bootloader nothing happened until i pressed and held the buttons whilst it was plugged in, then windows made the usb connected sound so i quickly mtty'd! lol
Hope this helps, Good luck!!!
martinbrettphilo said:
This might sound silly but it's worked for me in the past.
1. Go into bootloader (without mem card or sim)
2. Plug-in the USB cable
3. Hold the buttons to go into bootloader again whilst plugged in.
4. DOC Format
5. Flash ROM
My Universal had loads of problems but that is how i fixed it, tried everything else like you, when i first plugged it in on the bootloader nothing happened until i pressed and held the buttons whilst it was plugged in, then windows made the usb connected sound so i quickly mtty'd! lol
Hope this helps, Good luck!!!
Click to expand...
Click to collapse
Thank you...
Xda2 stuck in bootloader screen after failed flash in vista
blingin said:
My Dear Samaritans,
Tried reflashing but got an error and the flash failed... also the program crashed during recovery.
When I connect the device to the computer(s) "Serial" changes to "USB" stuck within the bootloader screen
Tried mtty (1.16 & 1.42) but neither give me the option of USB, only COM1 and COM2. And had already de-activated the USB connection in Activesync.
Have read through the forum but have had no luck.
I am ready to try anything, please help!
P.S: The error is Error 112
Click to expand...
Click to collapse
Hi i have had similar problems also i have an XDA 2 pda originaly had wm2003 on it (tried to flash it to wm2003se ) can someone help me also im realy at a loss =C many thanks in advance (i will give more detail if someone actualy) replys to me
Wrong forum
Welcome to the forum
Universal does not means all devices, actually is a model
Please enter into the right section of the forum
Goos luck,
Can you Help?
I have an XDA II was on O2 uk network. I used to flash it all the time and knew my way around. however recently i flashed it in vista without thinking.. and as i upgraded the rom from wm2003 to wm2003se about 25% of the way through vista disconnected the device then it was unrecognised usb.. then vista started installing new drivers that recognised the device... however this then crashed flashing the rom onto the pda..
It wont soft or hard reset, i took the battery out for 24 hours and tried again and nothing.. the only thing on screen is that it says serial on the top of the screen (which changes to usb when connected but get error 101 when trying to reflash/ no activesync connection and am confused my mtty as when it does connect i cant type into the text area only paste)
on the bottom of the screen is v1.06 (which before the flash crash was V1.0 something lower than v1.06)
basicaly is the device recoverable as long as i have this serial / usb recognition by the device????? (using mtty i cant connect through ports or usb but thats because i dont seem to understand how to use it)
the other question is is there any other way to get a rom back onto the device without mtty or activesynch..
I pray that ysomeone will respond .. i miss my pda dearly
a thousand thanks in advance
Hello guys!
I've got a bit of a problem here, because now my mobile refuses to connect with activesync and therefore making it impossible to flash it.
I read the readme in the cid bypass folder, and didn't quite understand it, but as keen as I was on getting a new rom I did it all wrong.
I actually copied the cid bypass folder to my sd-card and ran haret.exe from the phone. A friendly penguin appeared along with some green text, and it rebooted and went black. I waited for a while, but had no patience so I rebooted it again. But after this it has been impossible to connect it with activesync! I've tried hard reset and different computers but nothing works!
I'm hoping someone on this forum can help me!
best regards
Try this.
turn your phone off and press the camera button in then plug it into the USB port
you should get a multi color screen. If you do then you can flash.
But go here http://forum.xda-developers.com/showthread.php?t=330909
Go to where it says EDIT and follow what it says.
Oh and when a dos box opens up and ask you things just press the return key each time.
good luck
hey man, I tried reflashing the original rom to my vox, with the manualstyle sd card flash. So now it's flashed with the original rom, but still activesync doesn't work! anybody have an idea on how to make this right?
somebody tried running haret.exe from their phone, then flashing the Uspl with ruu flasher and then flash the new cooked rom?
My phone is not able to connect for flashing while in black state (after running harET), is it stupid of me to reboot it and start it by holding camera button while plugging it in to the computer? and then flash it with the ruu?
somebody please help me?
go into settings then connections then more till you see USB to PC
in there un-tick the box which says enable advaned network.
zipuz said:
somebody tried running haret.exe from their phone, then flashing the Uspl with ruu flasher and then flash the new cooked rom?
My phone is not able to connect for flashing while in black state (after running harET), is it stupid of me to reboot it and start it by holding camera button while plugging it in to the computer? and then flash it with the ruu?
somebody please help me?
Click to expand...
Click to collapse
I am confused..is it working or not? one post you say it is but you cant sink..then you say its not.????
and dont use the flash off the mem stick..use windows..
ok, sorry for making confusing posts! I'm just excited about getting it to work.
So here's the situation:
From stock phone used with exchange (turned off the exchange part before doing anything)
1. I ran haret.exe from my phone, and it rebooted into a "black state" after which I rebooted it again
2. I tried to connect it to my computer using activesync, to be able to flash, but it wouldn't connect. Activesync doesn't respond to my phone.
3. I flashed the shipped rom to my phone from my sd-card in good hope that it would reset the whole process, but it still won't connect to activesync.
So here's my problem; I want to flash a cooked rom to my phone, but I'm unable to connect it to my computer via activesync, what to do?
deuse said:
go into settings then connections then more till you see USB to PC
in there un-tick the box which says enable advaned network.
Click to expand...
Click to collapse
tried with both ticked and unticked, still nothing
Turn off your phone then keep the camera button pressed in at the same time plug it into the usb port
your should show diff colors on the screen..if so follow what it says in this link.
http://forum.xda-developers.com/showthread.php?t=330909
and do it from the pc not your mobile...
it's restored, but no activesync still
Is the cable you are using ok? or is it a new one you just got.
does windows see it when you plug it in? if so un-install active sync then reinstall it.
I'm having the same issue with Windows Mobile 6.5 ROM, activesync simply doesn't work ;/
ivanek666 said:
I'm having the same issue with Windows Mobile 6.5 ROM, activesync simply doesn't work ;/
Click to expand...
Click to collapse
Have you been into settings and un-ticked the box in USB to PC?
Also if you are trying to sync to office you must create a new partnership
google is your best friend.
I have no problems with sync in XP/Vista?windows 7 and office 2007
I am using FMs 1.1 WM 1.1
deuse said:
Is the cable you are using ok? or is it a new one you just got.
does windows see it when you plug it in? if so un-install active sync then reinstall it.
Click to expand...
Click to collapse
Windows notices my mobile (installs new drivers), but activesync doesn't register the device.
zipuz said:
Windows notices my mobile (installs new drivers), but activesync doesn't register the device.
Click to expand...
Click to collapse
Do the Hard reset .Then connect it to your machine.I hope this time it will work smoothly.
zipuz said:
Windows notices my mobile (installs new drivers), but activesync doesn't register the device.
Click to expand...
Click to collapse
Try this
open sync then at the top chose files then click on DELETE MOBILE DEVICE
see what happens..but post back if you fix it to help other people
yogusmilu said:
Do the Hard reset .Then connect it to your machine.I hope this time it will work smoothly.
Click to expand...
Click to collapse
I failed to mention that I've tried the hard reset as well, no luck.
I thought about the same thing Deuse, but there's no mobile device registered, so I'm not able to delete it.
It seems that you have tried every possible method! Anyway, my suggestion is install activesync in some other PC (friend's) and connect your phone there. See if it registers the phone. If it does then it is problem with the PC and not with phone. In that case, connect phone to PC and open controlpanel>System (icon)>Hardware tab>Device Manager Button in your PC. Unfold Network adapters and see if your phone is detected properly or it is detected with an "!" mark in "Unknown/Other device". If so, delete the device and disconnect phone. Reboot PC, reboot phone connect again and let the PC reinstall your device and see if it recognises your phone.
One more way (I think you might have tried this)- Uninstall Activesync and reinstall and connect phone.
By the way if your phone is not recognised in some other PC then it seems trouble with the phone.
Thanks.
Looks like your cable is faulty. Try activesync connection through bluetooth (for testing, ofcourse you cant flash from bt ).
parthabhatta said:
It seems that you have tried every possible method! Anyway, my suggestion is install activesync in some other PC (friend's) and connect your phone there. See if it registers the phone. If it does then it is problem with the PC and not with phone. In that case, connect phone to PC and open controlpanel>System (icon)>Hardware tab>Device Manager Button in your PC. Unfold Network adapters and see if your phone is detected properly or it is detected with an "!" mark in "Unknown/Other device". If so, delete the device and disconnect phone. Reboot PC, reboot phone connect again and let the PC reinstall your device and see if it recognises your phone.
One more way (I think you might have tried this)- Uninstall Activesync and reinstall and connect phone.
By the way if your phone is not recognised in some other PC then it seems trouble with the phone.
Thanks.
Click to expand...
Click to collapse
It's marked with an "!", will try it on my own pc next time I have it, worked there last time! if not, I'll have to live with