I am trying to isntall a new rom from some availabe in the kitchen but when it it tries to start to write it just stuck on the 0% and have to reset it again. Even hardspl same problem !! its an att kaiser from america arrived few days ago from ebay.
Can someone help me out please !!!
Radio info :
kais1*0
spl-1.93.0000
cpld-8
DON'T try to install a custom ROM without installing Hard SPL first. If you have problems installing Hard SPL, read the hard SPL thread for more information.
Deo said:
I am trying to isntall a new rom from some availabe in the kitchen but when it it tries to start to write it just stuck on the 0% and have to reset it again. Even hardspl same problem !! its an att kaiser from america arrived few days ago from ebay.
Can someone help me out please !!!
Radio info :
kais1*0
spl-1.93.0000
cpld-8
Click to expand...
Click to collapse
Have you read the 2 stickied threads right at the top of the main page of this forum about Hard-SPL? If not, then you didn't install Hard- SPL first. And if you didn't install Hard-SPL (and according to your quote it does not look like you did), then you are lucky that you have not Bricked your Tilt yet!
Read the following links as well as the Kaiser wiki and search for more info.
Link1, Link2 and there is a 3rd thread in this forum that talks about Hard-SPL on devices with the newest drivers on them.
Related
Hi I have a G4 Prophet and the IPL and SPL version number reads 2.10.0001.
I would like to flash it to use a WM6.1 ROM with the touchflo type functionality and new IE Mobile features (i.e. zooming).
I have read through all the guides about carrying this out and have even started having a go but am getting confused about HardSPL.
From what I read HardSPL CID Unlocks your phone so that you can install a diffeerent Carrier (e.g. Orange, Vodaphone) ROM ... or in fact a home 'cooked' ROM off of this site.
I have tried manually carrying out the HardSPL using both the Prophet Tools GUI and the command line batch file HardSPL however after the procedure finishes my IPL and SPL do not read differently as all posts indicate (i.e. they do not read 2.G4.4PDA) ... instead they remain as 2.10.0001.
I have seen the phone go to the tri-colour bootloader screen and even the progress bar go up correctly however when it reboots it says 2.10.0001. I'm assuming that I cannot go ahead and flash with a ROM (such as the Shadow TE one until the SPL reads 2.G4.4PDA).
Can anyone offere me some help with getting to this?
Many thanks.
Nick (a very much noob!)
nisgar2k said:
Hi I have a G4 Prophet and the IPL and SPL version number reads 2.10.0001.
I would like to flash it to use a WM6.1 ROM with the touchflo type functionality and new IE Mobile features (i.e. zooming).
I have read through all the guides about carrying this out and have even started having a go but am getting confused about HardSPL.
From what I read HardSPL CID Unlocks your phone so that you can install a diffeerent Carrier (e.g. Orange, Vodaphone) ROM ... or in fact a home 'cooked' ROM off of this site.
I have tried manually carrying out the HardSPL using both the Prophet Tools GUI and the command line batch file HardSPL however after the procedure finishes my IPL and SPL do not read differently as all posts indicate (i.e. they do not read 2.G4.4PDA) ... instead they remain as 2.10.0001.
I have seen the phone go to the tri-colour bootloader screen and even the progress bar go up correctly however when it reboots it says 2.10.0001. I'm assuming that I cannot go ahead and flash with a ROM (such as the Shadow TE one until the SPL reads 2.G4.4PDA).
Can anyone offere me some help with getting to this?
Many thanks.
Nick (a very much noob!)
Click to expand...
Click to collapse
I would recommend you use something like: http://forum.xda-developers.com/showthread.php?t=353547 It makes it a one stop upgrade... That uses "JumpSPL" rather than HardSPL which is the short term option.
Thanks for the help I tried the alternative lazy tool and it worked (http://forum.xda-developers.com/showpost.php?p=2141436&postcount=188) now my Orange SPV M600 has the Shadow Touch edition rom on it with the shadow cube addon, so far works a treat.
I would still be interested to know why the SPL version number did not change using the prophet tools or HardSPL on its own.
Anyway many thanks again.
Nick
nisgar2k said:
Thanks for the help I tried the alternative lazy tool and it worked (http://forum.xda-developers.com/showpost.php?p=2141436&postcount=188) now my Orange SPV M600 has the Shadow Touch edition rom on it with the shadow cube addon, so far works a treat.
I would still be interested to know why the SPL version number did not change using the prophet tools or HardSPL on its own.
Anyway many thanks again.
Nick
Click to expand...
Click to collapse
What is your devices IPL?
It may be because Soft/Jump SPL was not executed properly prior to HardSPL (this is automated through the HardSPL tools and Prophet Tools).
HardSpl Problem
l3v5y said:
What is your devices IPL?
It may be because Soft/Jump SPL was not executed properly prior to HardSPL (this is automated through the HardSPL tools and Prophet Tools).
Click to expand...
Click to collapse
i ran upgrade_hardspl_g4 on my prophet, my spl is 2.15 still... what should i do l3v5y? tried flashing it 5 times still no luck. Please help, having a hard time upgrading roms...
ipl: 2.20
spl: 2.15
im currently downloading prophet tools 2.8. i currently flashed my 818 with PV_temp rom. i'll try to install the prophet tools and hardspl my phone with it.. hope it works...will update in a few after the installation is done... downloading so slow... =(
*-----------------------------*
i did it!! thanks!!!
I made it, use SoftSPL.
I am a noob at flashing and this may have been explained already but i need better clarification.
I had previous sim and cid unlock my phone which is an Att tilt to now function with the T-mobile network.
In my my tri-color screen I have:
KAIS1*0 MFG
Spl-1.0. OliPof
CPLD-8
My radio is R 1.27.12.11
I used Olipof Hard Spl from my understanding,but I want to flash a new rom preferably Dutty v4. What I wanted to know is do I use a new Hard Spl since the rom is current and if so do I have to go through the same process? Also how do I actually flash the rom?
Again I know noob questions I apologize and would really appreciate your help and patience.
tony612 said:
I am a noob at flashing and this may have been explained already but i need better clarification.
I had previous sim and cid unlock my phone which is an Att tilt to now function with the T-mobile network.
In my my tri-color screen I have:
KAIS1*0 MFG
Spl-1.0. OliPof
CPLD-8
My radio is R 1.27.12.11
I used Olipof Hard Spl from my understanding,but I want to flash a new rom preferably Dutty v4. What I wanted to know is do I use a new Hard Spl since the rom is current and if so do I have to go through the same process? Also how do I actually flash the rom?
Again I know noob questions I apologize and would really appreciate your help and patience.
Click to expand...
Click to collapse
if you want to update your hardspl to one of the 3.** hardspls released by jockyw, you can. These hardspl's were released to get rid of the screen freezes reported by everybody using wm6.1 on the old hardspl's. If you have done hardspl flash before than use the same procedure to flash one of the newer hardspls.
Check dutty's thread for what hardspl he recommends. Most commonly advised are 3.29 and 3.28; i had 3.56 and never had any problems with any of the roms.
To flash the rom you have to make sure your device is connected to pc via activesync. Than basically you have to uncompress the rom rar that you downloaded from here. In your folder you will have a ruu_signed.nbh and a kaisercustomruu.exe. You start the flash process by clicking (or double clicking) on the kaisercustomruu.exe. MAKE SURE YOU PHONE IS CONNECTED TO PC when starting this process and battery life is atleast 50%.
Oh and you should always read the wiki to gain more insight related to your device as your question is asked quite often and before posting you SHOULD HAVE checked this thread:
http://forum.xda-developers.com/showthread.php?t=433835
--------------------------------------------------------------------------------
..i tried to install new windows..but ..later it just end up leaving in bootloader mode ...i tried hard spl...hard reset...tried unplug usb and battery too ..but neither work....can anyone help me to retain my jamin.....in bootloader mode it shows
IPL 1013.0001
SPL 2.20.0001
and when i do hard spl it shows
IPL 1013.0001
SPL 2.20.0001
GSM 02.47.21..with imate background ..and dont go further..
help please
..i have tried installing imate original version too ..but it says it cant ..coz it it says it need new nbf file and sometime ...ask to check upgrade utility...whats the problem...help me
See my posts about that on the forum under prophet upgrading, if you have any questions ask me ok, bye
deltav13 said:
See my posts about that on the forum under prophet upgrading, if you have any questions ask me ok, bye
Click to expand...
Click to collapse
which post, I have the same problem...I'm going crazy.....
i got elfin and i want to ask if it is any way to flash rom in bootloader mode,i want just to got my htc working again and my device is stucked at bootloader showing in right top corner RUU and on left IPL And SPL numbers.
ms2405 said:
i got elfin and i want to ask if it is any way to flash rom in bootloader mode,i want just to got my htc working again and my device is stucked at bootloader showing in right top corner RUU and on left IPL And SPL numbers.
Click to expand...
Click to collapse
hey, i just took a brief look in the elfin section. Go there and look at the stickies, there are guides for un bricking yoiur elfin and a good guide on how to correctly hardspl and flash....DO READ THEM (and you normally should flash a rom from bootloader in any case )
If you dont want to hardspl, then try the uspl way. You didnt say what rom you had tried to flash or wot you have done to get it stuck in bootloader.
Also are you using vista or xp on your computer?
i'm using xp on my comp,i got to bootloader because i tried to flash some roms and when i tried last time flashing onyx one it showed me error message and then started the problem.
ok, did u hard-spl sucessfully? what is you ips/spl shown on bootloader?
IPL is 2.26.0002
SPL is 2.26.0000 and as i said in right top corner RUU,
i've tried to flash it from sd card,but it ain't worked andlooked at goldcard method and i haven't got another winmo devic and don't know somebody who has,please help me to unbrick my phone,it was both from orange uk.
ms2405 said:
IPL is 2.26.0002
SPL is 2.26.0000 and as i said in right top corner RUU,
i've tried to flash it from sd card,but it ain't worked andlooked at goldcard method and i haven't got another winmo devic and don't know somebody who has,please help me to unbrick my phone,it was both from orange uk.
Click to expand...
Click to collapse
Please have a look at post 3 from here : http://forum.xda-developers.com/showthread.php?t=408637
Is this what you have tried doing previously?
Did you unlock your elfin first if it is locked on orange network?
If you cant get it working after trying this, go back to first link above and flash back an original stock rom, at least ur device will be working again!!
ps when u hardspl and tried to flash, did u disable antivirus on PC, and disconnect all other non essential usb devices? This is an commen cause of bad flashes, also try other usb ports, 2 of mine i cant flash on, 2 i can (which is wierd) - (i have experienced this myself).
If any of this doesnt help, as for help in the elfin section, but DO describe all your steps properly and fully and enclose links of roms tried etc so someone with an elfin can see what you have donw and save unnecassary posts etc.
mate,the link you gave me is that when i upgraded my elfin when it was working, i don't know what you mean about unlocked it is sim unlocked what about cid i really don't have idea,because i couldn't connect to mtty,please can you give me the link for original stock rom for my elfin,because i haven't done backup and i downloaded one but i don't know how to put in when i got in bootloader only and can't connect acivesync please tell me how to this aswell,PLEASE HELP ME UNBRICK MY ELFIN!!
Have you resolved this?
Search and download a stock rom from HTC or from here, use the search and wiki, you will find one there.
When you plug in ur elfin into the computer and put it in bootloader, do you see "USB" on the screen along with ur ipl and spl?
You should, and if you do you should be able to flash the stock rom on.
I tried to update HardSPL 3.29 on my friend's Kaiser from AT&T. But it still stucked.
I run SDA-Unlocker .It shows ok.
After serveral tries the phone stucked So i use Kaiser SuperCID and Security Unlocker v0.1 by ockyw2001SPL and do step 1. I don't know what i have exactly done.
During copy it stays at 95 % !
Now every time i boot the device it shows only the bootloader
KAIS1*0
SPL-3.56.0000
CPLD-8
Seial
I can't upgrade other ROM any more.
I think i should take HardSPL 3.56force USB ? because ATT already has SPL 3.56 and WM I 6.1
What have i to do now ? I'm a little confuse because the phone of my friends. That is the gift from his brother. :-(
read this then go to the sticky at the top of this forum and follow the links to the right thread for you to ask this in, good luck.
Ok ! I folow http://forum.xda-developers.com/showthread.php?t=420683
and tried to flash SPL 3.29 again. But it still stucked at 0%.
I will try the SD version.
Other question: should the battery loading at in bootloader ?
Hi,
Try re-flashing the stock ROM for the phone. You'll either find it on the wiki or on your carriers website.
Any more problems, please post in this thread : http://forum.xda-developers.com/showthread.php?t=423486 (after reading the 1st post o/c)
Dave