Related
Ok earlier i was trying to extraact the dk.01 rom i ran kasier kitchen extracted the nbh file. Then i used the folders to cook a new rom and didnt include any packages at all. So when i flashed this rom to the phone something went horribly wrong the phone stuck on the splash screen where it lists the rom radio and protocall version. Anyways i got mtty 1.42 and it doesnt have usb in the options Im using vista and niether wsecomm or the other process is running i even went to windows mobility center and turned usb off. then rebooted my computer. Tried two diffrent usb cables, the pc isnt even seeing a usb device connected to it. Is my tilt toast? Can i get away with telling the at&t insurance i lost the phone?
Sorry guys issue resolved i just help camera power and reset and it loaded hard spl.
problem solved
I had RTconfig installed on my ATT Tilt. I had to reinstall Windows 6.1 to make it run again. Before that I had RTconfig installed. After I installed 6.1 (and RTconfig was gone from my phone as were all my apps) I got a new SIM card with a new phone number. Now I installed RTconfig again. When I turn on my phone, it calls my emergency # and says the sim card was changed. How do I get it to recognize my new sim card as valid?
Hi there, I tired to issue my problem in some other threads, but without any response so far - probably my problem is more specific.
I was using AHEN 6.5-R6i Rom for few weeks when some time after charging my Raphael was not powering up at all. I presume no relation between Ahen rom and the problem (as described further).
I bought new battery and it occurred that probably power charging circuit was damaged, because it newer completed charging, the device was always very hot and discharged in few minutes even when turned off (until completely drained out). What is more the USB connector works only for charging (maybe damaged data connection circuit?).
As a result, before returning the device for guarantee servicing I wanted to downgrade all the roms to the original ones. As advised I started with Radio and OS stocks, but after bootloader update (from SD card, cause my USB doesn't work) I got only "upgrading ROM code error" and the device tries to load some ROM, but putting any on SD card doesn't work anymore.
Any suggestions how to cope with this situation?
If you need help please provide us with important information. So fill your signature first. Mainly if you have hard-spl or if you bought olipro cid unlock and what exactly you have done until now. Also wether your device is CDMA or GSM? If it is GSM than you have to first restore Stock Radio first, after that if you cid-unlocked the phone you have to relock it again. Than remove hard-spl and install stock ROM. But if your USB is broken, i think there is no chance to remove Hard-SPL neither to restore to stock. Remember that when you are in a bootloader and you do not see that the device is connected to activesync or Windows Mobile Device Center it does not mean that it is not connected. Just check you hear the sound indicating that something is connected to usb in vista or windows xp.
If you need help please provide us with important information. So fill your signature first.
=> done
Mainly if you have hard-spl or if you bought olipro cid unlock and what exactly you have done until now.
=> chnged SPL to OliNex, OS to AHEN 6.5-R6i, Radio to version required by AHEN rom
Also wether your device is CDMA or GSM? If it is GSM than you have to first restore Stock Radio first, after that if you cid-unlocked the phone you have to relock it again. Than remove hard-spl and install stock ROM.
=> I retracked the changes as indicated changing both radio and OS to original ones, but had just problem at last step = flashing oryginal SPL (because I made it from SD).
But if your USB is broken, i think there is no chance to remove Hard-SPL neither to restore to stock.
=> Hmm, anyway right now I am stack because bootloader is "loading ..." every time I reboot the device.
Remember that when you are in a bootloader and you do not see that the device is connected to activesync or Windows Mobile Device Center it does not mean that it is not connected. Just check you hear the sound indicating that something is connected to usb in vista or windows xp.
=> I tried to use some terminals to see if I can execute commands directly or see any output, but I haven't even succeeded to open the port. Maybe I am doing something wrong - I give it a try once more tonight.
So what version of SPL is bootloader showing? If it's showing something like 1.90.0000, you are in bootloader and USB circuit is not damaged you should be able to normaly flash ROM from your provider from bootloader. So download the ROM from your T-Mobile it should be some exe. When you see bootloader tricolor screen coonect usb cable from Touch Pro to computer and run the exe soubor with your desired ROM. It should work if everything is OK!
If your device is showing 1.90.OliNex, than i cant help you because i do not know how to remove Hard-SPL from bootloader, maybe it is possible, but for more experienced tech guy, who i am not
PS: Hope you did not bricked your device because Hard-SPL and removing Hard-SPL is all done with cable, you cant do it from SD, and you cant flash original SPL before removing Hard-SPL!
hmm, it seems that I have managed to flash, at least partly, the original SPL from SD card, cause it shows version 1.90.0000. Partly, because it states that the previalus rom update was not successful :-(
In this state (in boot loader mode) I can't even charge battery so I have to do it externaly. Connecting to PC doesn't work (PC USB and cable are fine). The only thing that change after connecting to USB charger is that device gets hot ...
i am sorry to say, that you probably bricked your device... Maybe someone could help with more advanced hardware, software support, but i am not the right person...You can try to put your device to service and hope they will not recognize what have you done, but it depends on your stock SPL version. I got czech T-Mobile and stock SPL was 1.69.0000, so maybe yours was the same...
Next time please read more carefully, search or ask someone if you are not still sure, things about flashing SPLs are very dangerous if they are not done carefully...
Can anyone help this guy? He tried to flash original SPL over Hard-SPL, and therefore it is not looking very well for him to unbrick his Touch Pro...
So ... I got it from the service and they changed the motherboard and the battery, no charges
It was brickes, because of cherging circuit issue.
Unfortunatley I send it back to service, because the loudspeaker is not working ...
Actually I am the same exact boat as the OP. My phone stopped charging and its because the USB port is broken. I need to change the phone back to stock but if its not charging its probably not going to get a connection to the computer either. I read that on at least the Hermes it was possible to flash from the SD card. This is not possible for the TP? Thanks
riotburn said:
Actually I am the same exact boat as the OP. My phone stopped charging and its because the USB port is broken. I need to change the phone back to stock but if its not charging its probably not going to get a connection to the computer either. I read that on at least the Hermes it was possible to flash from the SD card. This is not possible for the TP? Thanks
Click to expand...
Click to collapse
You can flash the ROM, radio, splash screens etc etc from SD card - you will then have to send the phone back with hard spl still installed as you need a usb connection to remove it.
Dont assume you cant get a usb data conenction though - try it and see!
I did try the connection, didn't work. How do you flash from the sdcard? I just dont want to brick it.
Please read this thread on how to flash (including how to flash from SD card).
Again, (assuming you have the correct hard SPL currently flashed) you can flash a ROM, radio & splash screens etc to your phone from the SD card (one at a time) but as previously said you need a USB connection to flash hard spl (dont attempt it from the sd card).
So, my Raphael arrived from service after the second repair (loudspeaker not working) - it seems all works this time
By the way, that is correct that a USB connection is necessary to flash hard spl, but .. I was desperate because the USB was broken, so I tried it from SD. The effect was good enough for the service - the Hard-SPL seemed to be reverted to oryginal one, however the booting was stacked at loading the ROM
Well, I've updated few htcs before and everything went fine. But there's always the first time...
I upgraded my htc hd2 spl 1.42.0000 to hspl2, wanted to upgrade rom/radio too, but couldn't find any rom I do like, and then I got no more leisure to play with it. So there was only hspl2 replaced on the device and that's it. Everything was fine for a month or two, then suddenly the phone function stopped to work (couldn't register into network anymore). Wanted to send back to factory for repair, but to avoid warranty loss I wanted to downgrade the hspl to stock spl. Downloaded stock image at htc site (was 1.48.something), did everything exactly in a way described in the video tutor, and - got stuck on light gray "Loading..." screen after the colourful one, and nothing more. Tried to update ROM via activesync for test, got stuck at 0% and that's it (although the connection is fine), googled a lot, browsed a lot of xda-dev... still nothing useful found.
Technical info + what shows in the colourful screen:
Eastern Europe HTC HD2
PB81100 HX-BC
SPL-2.08.0000 8G XE
I would really appreciate if someone could tell me, what it is, and how to fix it!
Thank you in advance.
I believe when you did the original HSPL, you selected the wrong version. The SPLs that end with '.0000' are the stock ones. Assuming the HSPL was done correctly it should read "2.08.hspl". Try flashing HSPL again, this time select .hspl, then flash your ROM. Should be good to go.
Edit: When people say you need a stock SPL to send it in for warranty, Im not sure if you need the exact same one it came with or not. Because you basically just reflashed a stock one anyway, you might be able to just send it in for repairs as is, but Im not 100% on that.
donkeypunch85 said:
Try flashing HSPL again
Click to expand...
Click to collapse
Thanks for the tip and trick. Unfortunately, like I said this doesn't help, cause flashing doesn't work. Tried hspl2 and hspl3 as well. The screen turns 3-color, then gray "Loading..." like it was when flashing from sdcard, and stucking on it...
When installing hspl3, the software on the computer says (while having that "Loading..." screen on the phone):
CRITICAL ERROR
Flow: 00000001
Error code: 00000002
Description: USB Connect failed!
(although ActiveSync shows connected and sync/exploring runs fine)
I'm becoming really unhappy with this one.
What OS is on your PC? Are you making sure Anti-Virus is disabled before flashing? If Win7 right click on the HSPL and choose 'run as admin'. Your using a USB slot on the rear (main motherboard) of your PC and not one of the front ones right?
It suddenly started to work today. I have no idea, what happened, did the same steps as before. The GSM function is still broken, but now, as the flashing worked finally, I'm able to send it back for repair without a risk to lose warranty. Mystical.
Thanks anyway for your time and willing to help.
...had the same these days on an HD2 which I successfully up-/downgraded at least half a dozen times before.
Did the MTTY 29 thing (again, surely the 6th time, never had any problem before) and afterwards had the issue you describe.
What helped me was re-flashing the HardSPL. Afterwards all worked 'as usual'.
Hope that helps others, Franky
Ok
and if my usb plug is broken?
I can't flash from sd, because it stops on the 'loading...' screen. I even tried the gold card method and still stuck on 'loading...'.
Wat's even worse my current system is rather unstable and WM sees only 208mb of ram...
Any suggestions?
T-mobile HD2! Problem Flashing rom
Hi Guys,
I'm a new guy in this great site, because I bought a T-mobile HD2 recently, via china, and it's not a fake!!!
But I want to update its rom to put the android2.2 's system.
I have tried several methods find in this site. But during the rom's flash, my phone shutdown and the connexion between Pc and phone switch off.
The phone is only in sleep mode and not off.
Can you help me to resolve this problem?
My system :
Phone :
Not SPL on the bootloader (only tri color) and this message :
" Error :
Copying file from SD card failed.
The system will shut down"
OS : Windows mobile 6.5 Professionnel
Software version : DUMA.10X.W10.20.P29
Protocol Stack (software) version :
MAUI.09B.W10.16.MP.V5, 2010/06/07
Dual Sim, and no take off SD card storage
Rom version : v01.00
Rom Date : Sep 10 2010
Boot version 2010 08 01
PCB version v01
Model ID T8585 (Leo)
Manufacturer HTC
CPU QUALCOMM 8250B (1024 MHz)
Ram Size 576 Mb
Nand Size 1024 Mb
Data bus 32 bit
Memory CPU 194 Mo
Memory storage 385 Mo
Memory inside SD card storage 7362 Mo
PC :
OS Windows XP SP2
ActivSyn4.5 Ok, but not synchronization with outlook, but connexion between PC and phone is OK.
Use update Rom Flash : Rom T-mobile v3.14 (run OK, no problem until progress bar (phone in sleep mode).
I tried SD card's method, unless sucess.
I used qmax to find SD card's number. But the memory's value is 3,5 Gb and not 7,3G.
Well, I think, I have forgot anything!
Thanks for your help!
Best regard
If you can get to the bootloader (four color stripes) then do so and then connect the phone to the PC. Wait until word 'serial' changes to 'USB'. Then start update on the PC (normally click the _RUU_(...).exe and follow the steps).
If fails please write at what point.
htc hd2
tomus said:
If you can get to the bootloader (four color stripes) then do so and then connect the phone to the PC. Wait until word 'serial' changes to 'USB'. Then start update on the PC (normally click the _RUU_(...).exe and follow the steps).
If fails please write at what point.
Click to expand...
Click to collapse
it fails at 8%.
Hello, mates!
Today I've made hard reset. After that my phone stopped recognizing any sim-cards. It writes that sim card isn't inserted. I've tried 3 sim cards without any success. All of this sim-cards work just fine in another phone.
I've already tried to do one more hard reset. And I've already tried to take sim card from the phone and boot it without card. It wasn't helpful.
Have you got any ideas?
Sim module is connected to the maniboard with the help of flex cable.It may be partiarlly dissconected.
I've already checked it twice... It's conected, I'm sure.
p.s.: flashlight is working great.
Have you tried to reflash rom?
No, I haven't. I tried to download 7.0.7389 ROM that you've uploaded, but I still can't download it.
Can you give me some advice where can I get 7008 or earlier build, or re-upload 7389 to another file srver?
I found many ROMs for other HTC devices, but not for "7 PRO".
http://rapidshare.com/files/4546556....64.09.20_22.42.50.15_Signed_GOLD_RELEASE.exe
Ok, downloading it. But do you have any links to 7008 or earlier builds? I don't want to lose jailbreak...
Unfortunately,for HTC 7 PRO there are no older build available.
oops... RUU updater says that it can't connect to device, code 260.
And I unable to unlock it through Chevron WP7. It says that my device probably PIN-locked or Zune is switched off. Both are turned on.
I tried to do soft & hard reset my phone. And I tried to reboot PC. Hopefully that problem due to using Windows 7 through Virtual machine. I use Mac OS...
Tomorrow I will be able to test it at work, on a real PC with Win 7. I hope it would be a solution.
You can switch HTC 7 PRO to bootloader manualy,connect to PC, then run the exe ROM
Ok, I'm in SPL now, but when I mount it to PC there is no driver and there is sign at the white strip "Serial". I suppose that it should be changed to "USB" when I connect device to PC. But it is doesn't occur.
Got it. Trying to update.
Strange behaviour. I updated the device to 7389. I unable to update it through Zune to 7390 - no update available.
Upd: connected device to Win 7 notebook, installed Zune, and here was an update to 7390.
But the most terrible thing that my sim-card still can't be recognized...