I'm using "Dutty's TouchFlo Rom 2 Final" on my tilt, but am facing problem with call end key. It doesn't respond during call and even in sleep mode...
I installed Tilt keyboard fix but no success..
Any help would be appreciated..
Regards..
I tried original ATT ROM... I think its hardware problem... coz when I press repeatedly it works... Can anyone help me out or tell me any solution..
Function design issue!
It is a design issue. To end a call you must either press the End Call (Hang-Up) button twice or press and hold on it. From a design stand point, this would prevent inadvertent hanging up on your caller while holding onto the phone and just clicking the hang-up button by mistake. At least that is what I was told by HTC.
Thank you so much asfoor. But sometimes i just end call with a single click and some time I have to press hard to end the call, same is when it goes to sleep mode...
I don't have that issue on the TyTN II. If it happens with different ROMs, then it's a hardware issue -- probably something in the contacts area.
it means i have to open it
Related
Is there a setting to silence the phone on an incoming call when the phone is locked? Pressing the volume up or down WON'T work with me.
Thanks in advance.
i just tried on my phone several times from different numbers and it works fine for me.. both buttons too
Were you using any program such as manic AutoKeylock? or you just held the end call button to lock it?
Maybe I need to reset it but I didn't install any programs.
just end button i did not think i needed a program to autolock my phone
silence
Hi,
when somebody calls me i would like to silence the ringtone and not hangup. (on sonyericsson you press the side key for volume)
pressing volume up or down doesn't work for me either. is there a place in settings where you have to enable this feature? (i sure couldn't find it )
I would like to confirm that a hard reset fixed the problem! Pressing volume down while phone is locked SHOULD silence the phone by default.
Could be some software glitch that messed it up in the first place.
Figured out the problem. It seems to me that when there is an active connection, i.e EDGE is connected and it is showing in the near the cell signal, you WON'T be able to silence it by pressing a volume down.
If you go to connection manager and disconnect Edge by pressing 6, then lock it and let somebody call you, you WILL be able to silence it!
I have tried the above three times to confirm it. Seems pretty messed up if you ask me!
If you know how to solve the problem, please let me know.
Anybody figured out the problem (Read above)? I will paypal you $20 if you can get this to work!
Really, why did they mess it up like that when my previous phone, SDA, worked!
Hi,
It gets really annoying when I return home and notice that while I was driving I accidentally send some e-mails and made some phone calls to unknown and known people...
This has happened because the BT answer button was pressed, the phone woke up, and it was "touched" in various places making a "costly" mess.
I have also installed S2U with S2A but still the phone wakes up..
How can I stop this???
any help will be appreciated!
PS: I use a Touch Diamond.
I guess either there is not a way to do that, or my mediocre english didn't help anyone understand my problem...
Do you have any third party software installed? If yes, most probably it's due to software incompatibility that caused your diamond to react in this manner.
"HKLM/Software/OEM/VoiceCommand/Path" is what is carried out when the bluetooth button is pressed. Just delete or change the value.
Next time use the q&a section for this type of query.
I have a HTC Kaiser phone with HTC oficial spanish rom.
My problem is...that after some weeks after a fresh rom load, calls start instantly failing when dialed. Ill explain myself, when I open my contact list and dial someone, i dont have a problem, but when i actually dial a new number and press send, the call will last 00.00 and just shows "Call finished".
Any clues??
Thanks for your time and answers =)
bump, help please?
it amy have been a bad rom flash , or you may not have hard reset after the flash.
also sometimes phone problems require only a soft reset (put your stylus in the little hole in the bottom to do this)
HARD RESET:
for a hard reset hold down the two soft buttons and then put your stylus in the hole HOLD THE BUTTONS DDOWN UNTIL THE SCREEN COMES BACK UP it will ask for confirmation and select yes by hitting the send button
Anyone have problems with the 4 hard keys on the front of the phone and the scroll wheel? Talking about the att fuze here. Randomly when using the text program it will scroll in and out without stopping. Only way to make it stop is to press the power button to turn the screen off then again to turn the screen back on. Also, when i press the bottom left key to bring up the dialer sometimes it will not and just do nothing. Just as in a phone call i press the bottom right hard key to hang up the call and sometimes it will not respond what so ever.
I know the keys work because when i press them they light up showing i pressed them but they have no effect. This happens about 50% of the time and not at all rom related. I have tried over 8 different roms including those with tf3d2 and wm6.5 and all have the same problem. I have even tried flashing to the stock att rom and even on that rom i am still having this problem. I have never dropped my phone or any physical damage. Any ideas? I have already called warranty exchange and have another fuze on its way to me. I am convinced it has to be hardware related some how since no rom will work 100% for me with these keys. I have had my phone since january and out of the blue this all started about 3 weeks ago.
Bump Bump Bump
I dont have that problem, but sometimes my keys dont work and I have to turn off the screen and turn it back on
sometimes I even have to soft-reset my phone
this is partially because the Left and Right directional button is roughly between the Home/pick up and Back/hang up keys respectively. you have to press more towards the corner otherwise it will register as a left or right press.
another situation is when it is running a bunch of processes in the background it forgets what keys are what and you just have to turn it off and turn it back on (the display) and it should work again. that or open a random program and exit out back into tf3d
goodluck
Actually, I have exactly the problem that you're reporting where the zoom in happens circurlarly, without any ceasing. It's driving me batty.
hi,
sorry for this lengthy message. But pls, experts look into this.
my father was having an Imate jama 201. 3 yrs ago, he kept inside since it did not work properly for him. That time i did not know what the problem was. Now i have caught hold of that.
The phone switches on properly. The welcome screen is seen. If there is no Sim card, it displays a msg. When i put a Sim card, it displays the operator name as well as the G- GPRS symbol. But when i click the start button or any key, it operates very very slowly.
In the navigation buttons i can only press the down button to go down a menu, but that too, by pressing the left key along with it. The right selection button( long rectangle near back button,) does not respond when i click it. But if the phone back light goes out, the phone responds back by coming back again to the home screen, on clicking that button.
I dont know whether this is a software or a hardware problem. The phone, very rarely is able to work without any sluggishness. I am able to view the preloaded gifs and images in the pictures menu and even go to camera mode.
I am able to receive calls and messages, but since the buttons don't respond properly, i am not able to answer them. The ring tone is loud enough to hear when i get a call.
I have no important data in it, so i am willing to flash it irrespective of any data loss, if required.
I am ready to answer any of your queries regarding this issue.
Thanks in Advance
You should try to make a hard-reset!
actually, most of the keys in it wont work properly. You just press randomly some keys in it, only a letter appears. i am able to go till the hard reset menu, but not able to enter the number: 1234