Hi All, excuse this, I have tried everything else including the i-mate site who leave alot to be desired ( I was goin through the process of upgrading my Jasjar to WM6 & did not follow the instructions asa you do... My Jasjar has now totally reset itself back to the basic screen without windows installed so it seems, all I get is a blank unpowered screen with v1.00 at the bottom, have tried plugging it into my USB port, which just says it does not recognise it. I have also lost my WM5 CD, so can't even restore from there.. can anyone advis me what to do next.... i'm pulling my hair out (what little of it I have )
Thanks
NP
Just restart the OS load, try in with the MaUpgradeUt_noID.exe , and that is it!
Oh happy days!! Logged into the main screen this morning & there it was, reseting your device from bootloader screen.... Now to upgrade to WM6
Where would all of us Mr Average PDA users be without you guys!
Thanks
Related
Hi everyone I have one problem , My I-mate jamin (G3) can not turn on by it's battery (and another Original batt ) , when I finish upgrade to WM6 . But it can turn on by extension DC 4volt feed up and working well with no battery icon.
Anyone have solusion ???
i-mate JAMin
Hello,
the i-mate JAMin is not a 3G device, and i think that the reason that you dont have the battery icon any more that used to show on the device before upgrading to wm2006, which is not safe as you might loose some of the main parts of the original operating system that the device can handle, but the 2006 is not designed to work on the wm2005 devices, i think what you can do is to try to hard reset the device for two or three times and if needed try to install the operating system from the original company of the device (I-MATE) but when you try that make sure the device is in the boot loader mode. and good luck
Thank for your answer but now my i-mate get stuck screan ,affter upgade around
did you CID unlocked your G3 Jamin before upgrade to WM6 ?
try to reach to Boot loader and Downgrade with WM5 and test your device with battery
JAMin
i think you should try hard resetting the device to try to get back the previous wm2005, to hard reset Press and hold continuously at the Comm + Camera buttons then press the power button once, even it didnt work from the fist time try it once or two times. good luck
Hi everybody,
i have flashed the WM6 underground edition a couple of weeks back. Now i wanted to downgrade to WM5, but without success. I am using IPL/SPL 2.21. After starting the ruu upgrade software the Wizard switches to boot mode. So far so good.... But then nothing happens anymore and after a minute or so the software quits with error 260.
Any hints what to do ??
I have the newest Activesync installed.. I even cannot flash any other Wm6 rom.
Any help would really be appreciated !!!!
Best regards
Batman08
When you reboot your phone, post exactly what version IPL and SPL you see.
Didn't someone once post that there was a difference in USB cables....Grasping at straws, but just a thought!
Hmmm... do you hear the active sync connection bell ring when it reboots into bootloader? At the bottom of the screen, do you see the letters USB near the left hardkey?
Might try another PC, or even a different USB port on the same machine. Sounds like the USB is acting up.
After the phone reboots i can see IPL/SPL 2.11.
I can hear three bell rings with the same low frequency. To
me that is not correct as the connection bell ring should be two tones ?
I can see "USB" on the left side of the Wizard's screen.
I also tried different cables, but no success.
I am using WIN XP with SP2. Upgrading worked flawless
some month back with WM5.
The only thing i had to change was ActiveSync 4.5 as WM6 is only
supported there.
Any hint ???
batman08 said:
After the phone reboots i can see IPL/SPL 2.11.
I can hear three bell rings with the same low frequency. To
me that is not correct as the connection bell ring should be two tones ?
I can see "USB" on the left side of the Wizard's screen.
I also tried different cables, but no success.
I am using WIN XP with SP2. Upgrading worked flawless
some month back with WM5.
The only thing i had to change was ActiveSync 4.5 as WM6 is only
supported there.
Any hint ???
Click to expand...
Click to collapse
ERROR [248~260] : UPDATE ERROR
This error occurs when there is an “open port error” before upgrading the CE ROM image.
Solution: You can reset the device and run RUU again. If you still encounter an “OPEN PORT ERROR” again, reset your computer and try again.
This is taken from the redme inside the RUU
Good Luck
Put the phone into bootloader mode, kill WCESCOMM.exe from process list, attach Wizard, let it install driver, open up RUU and (hopefully) flash.
Also make sure you pull out your SD card while you try to flash your phone.
@neonkoala:
You made my day !!!!!!!! it worked flawless.... Thanks a lot !
After I tried to upgrade the rom to WM6, my JAMin got stuck at bootloader. After that, I tried to flash WM5 roms without success and suddenly (after a reset) the screen became white with some horizontal and vertical lines constantly moving. I discovered that it was only the screen that was garbled as it still connected to PC, so I installed (without seeing anything on my JAMin) the NVID ROM trying to restore it. It installed sucessfully, but the screen remained garbled with the white background and random lines. I know it was sucessfully installed because I heard the typical "welcome" sound before configuration.
Do you know any way to restore the screen? Or must I send it to I-Mate to repair?
You can try and reattach the screen cable to the rest of the device, but this will boid any warranty you have, and may damage your device further. If the device is under warranty, I would suggest flashing the ROM the device came with (unfortunately the FTP server is down at the moment, so it might take some fishing around for) and sending the device back to get repaired properly.
mpmf said:
After I tried to upgrade the rom to WM6, my JAMin got stuck at bootloader. After that, I tried to flash WM5 roms without success and suddenly (after a reset) the screen became white with some horizontal and vertical lines constantly moving. I discovered that it was only the screen that was garbled as it still connected to PC, so I installed (without seeing anything on my JAMin) the NVID ROM trying to restore it. It installed sucessfully, but the screen remained garbled with the white background and random lines. I know it was sucessfully installed because I heard the typical "welcome" sound before configuration.
Do you know any way to restore the screen? Or must I send it to I-Mate to repair?
Click to expand...
Click to collapse
Hi frd,
I have exactly the same problem!
Nothing , only the f*** white screen!
I can browse the device via active sync, can rcv calls but the white screen.
I have checked the ribbon connector of the LCD and make reflashing some ROMs but nothing.
I still wondering is it hardware or software problem!
Please let me know if you have progress!
Thanks
G.
Try to replace LCD module, I think thats right way.
It will be a hard ware problem. Probably the ribbon cable as the screen is showing something so it must be working at least a bit.
Hello,
i have the same Problem with my QTEK S200.
First i changed the Rom and it worked perfectly for two days.
Then i had to change my Sim card and after that the problem came again.
I tryed a lot of times to reflash the rom but the problem persist.
How can it be that it worked again for some days ?!
is it the touchscreen of the lcd unit i have to replace ?
is it possible to do it by my self ?
thanks for your help !
Hi everyone.
I had a similar problem an hour ago (Qtek S200 G3):
I Upgraded to a 6.1 rom and then to another, after that my device was stuck in bootloader(3 colour screen). Any 6.1 rom that I tried would install, but after installation device always boot in to the 3 colour screen.
I tried this original shipped rom http://files.mail.ru/HZUAH1 (it's WorldWidwEnglish) (to download just click the link "скачать" or the file name RUU_Prophet_220734_2207114_024721_QtekWWE_Ship.exe
) and it installed!!! It TAKES A WHILE TO INSTALL!!! But it worked!!!
May want to try it.
Hope this helps.
hello,
picture on screen was immediatly clean again ( bootload image ).
it was impossible to change the rom because i have a G4 model.
i flashed the rom with another french rom for G4 and it worked perfekt.
now i tried to remove the battery again for 3 seconds and now i have the same problem again. really strange ....
i tryed the same procedure again but no success.
I reinstalled differents rom's again starting always installation from bootloader.
After about 10 new installations i've clean picture again.
now i'll not put off, restart, or take of battery till one of you know what's the problem.
Thank you for your help !!
are you guys sure its not an intermitant hardware problem, it sounds like it to me. if yu were able to get a clean picture for a short time and now its white again, it cannot be the rom? As for replacing it, nothing is impossible and there is always ebay and google
QTEK S200 G4 CID unlock
How can I CID unlock a device that need´s that to upgrade the Rom?
Is there already any program that , Lockwiz dont do the job, can performe the unlock?
Thank you.
For G4 CID unlocking, you need to user Hard/Soft SPL.
same problem
my imate jamin got the same problem. it happens only and only when I remove the battery and when I leave it to charge for 1-2 days the LCD works again and show clear pic. any suggestion? activesync and &... are all ok!
Well, i upgraded to windows Mobile 6, but haven't removed the batterie anymore.
But i'm able to put it off now, what was impossible before.
I am posting this here since there seems to be way too many threads around here all saying the same thing diffently yet in NO clear way that everyone can understand. I spent 2 days trying to recoved a Prophet from a bad flash.
Symptoms
Prophet stuck in Bootloaded (Tri Color Screen)
Prophet stuck in 2nd Splash (Usually Your providers Splashcreen)
Solution Read as (This is what I did to fix it)
Download a WM5 Prophet\Wizard Official Rom (I still own a Wizard so I used the K-JAM_WWE_216901_2169101_020710_ship rom, the devices are very similiar concerning chipsets with the hardware keyboard seeming to be the biggest difference)
Extract the Rom (if it is distributed in an exe format with a tool like Winrar or 7zip)
Download the Prophet Tools Light package and extract to any folder . This contains both G3 and G4 RUU's (I can confirm this worked on a G4 Device)
Place the Official nk.nbf in the \Utils\Flash folder
Drop the phone into bootloader (Tri Color Screen) mode and connect to PC via usb.
Allow a few seconds for the usb connection to settle and run the RUU specific to your device.
DO NOT TOUCH the device or PC at this point. If your pc is a tad slow, go make some coffee and watch an episode of Big Bang Theory
This should now give you a shiny new (or old ) rom that is bootable which will allow you to upgrade your Prophet to any of the pretty WM 6.1 roms available.
Just a little tip:
If you are worried about messing up the device again use Alternate "Lazy tool" by dioxda. Its easy and it works !
I couldnt make this process any clearer if I tried
heeey...sorry but after this my prophet go death... i cant turn it on, and i dont know how but it seems that i cant charge it no more...
is death... can anybody help me how 2 fix this?
P.S.sorry if my eanglish is not very good.
specto13 said:
heeey...sorry but after this my prophet go death... i cant turn it on, and i dont know how but it seems that i cant charge it no more...
is death... can anybody help me how 2 fix this?
P.S.sorry if my eanglish is not very good.
Click to expand...
Click to collapse
Strange this worked perfectly for me, but when I tried updating to a different rom I got the same problem you are facing now. Just a quick flash on the screen and blue and red LED flash. If I plug it in it just sits there flashing the whole time. I am looking into this as soon as I get a solution I will post it here. Any help guys ?
cornelha said:
Strange this worked perfectly for me, but when I tried updating to a different rom I got the same problem you are facing now. Just a quick flash on the screen and blue and red LED flash. If I plug it in it just sits there flashing the whole time. I am looking into this as soon as I get a solution I will post it here. Any help guys ?
Click to expand...
Click to collapse
Recovery
http://forum.xda-developers.com/showthread.php?t=401326
If at any stage your Prophet fails to start properly or can only enter bootloader follow this:
* Download and install the latest version of ActiveSync (Google for it)
* Download and unzip an AKU2.2 (No Vendor) ROM for the Prophet-any AKU 2.2 will do-from [here | ftp://xda:[email protected]_NVID.exe] or [here | http://wiki.xda-developers.com/index...=Prophet_ROMs]
* Within ActiveSync DISABLE connect through USB (Tools->Connection Settings->Uncheck Allow Connect through USB)
* Put the Prophet into bootloader mode (hold the camera button and insert the stylus into the larger hole next to the power socket)
* Plug the Prophet in via USB
* Run the RUU specific to your device (G3 or G4) from the AKU2.2 folder. If there is only one RUU, use that.
* When it has finished: disconnect the Prophet, and then re-enable the connect through USB in actyivesync before reconnecting the device.
==> if success, will going back into WM5 and then u can use the Lazzy Tool, look at http://forum.xda-developers.com/showthread.php?t=353547
choose WM 6.1 ROM, after u doing that step, u already done with the WM 6.1 SEMOGA SUKSES!
yes it works again ...
Help, please?
Hi guys,
I have a slightly different problem. When I turn on my Prophet, it is in bootloader mode, so I take out the battery, leave for 3 seconds, put the battery back in, turn on the Prohpet.
Bootloader is displayed
Plug into PC with Active Sync 4.5 running (USB disabled)
Windows makes the 'new hardware connected' sound
RUU shows USB in bottom corner
Run the NVID no vender ROM,
Agree to first screen
Agree to second screen
Click Next
Prophet turns off
Windows makes the 'hardware disconnected' sound
Argh
No Prophet, no phone - incommunicado!
When I turn the prophet on now, I just get the bootloader, then it turns itself off after 10 seconds.
Could it be a low battery? - How do I charge it? I have left it plugged in to the power all night!!!
Could it be a faulty phone? - I have been having random resets over the past 3 weeks or so and thought that it was the WM6.1 rom installed, so was trying to put WM5 back on to see if that helps. - I am beginning to think there may be something wrong with the device?
I am trying a few more things from this forum before giving up and buying a new windows smartphone!
Any help would be apreciated!
Regards Mike
Guess it could be a power issue. - I got further just now by using a powered cradle instead of just a usb cable, but still reset at 80% complete. Will leave the phone charging using a wall charger only for an hour and see how i get on with that!
Its Fixed!
Ok,
So it turned out to be a low battery. - I charged the Prophet up for 1 hour and then ran the re-flash and it worked perfectly.
Now I just need to get the Orange rom back on it so its back to normal - Not faffing with WM6.1 - will stick to WM5 as its much quicker and works!
Maybe I was a bit too fast in posting the problem!
Thanks
Mike.
Hi, a few days ago i bought a TREO 750, with WM5 running, everything seems to work fine but when i tried to connect it to the PC nothing happens besides start charging , does not appear the plug n play assistant on the pc or anything else.
I tried to upgrade from the memory card but nothing happens and when i get into the flashing mode does not appear the "USB" connection mode, on the screen.
What can i do?? , any advice could help me.
Thanks in advance
http://forum.xda-developers.com/showthread.php?t=659125
startngate tks man, but there is no solution on that post so i'm asking for any other sugestions
thanks again!!
Same here ... it used to be that it would work now and again if I unplugged/replugged enough times but since I updated from 5.2 to 6.0 it doesn't work whatsoever. I really want to upgrade to 6.1 or 6.5. =/