Hi everyone I have one problem , My I-mate jamin (G3) can not turn on by it's battery (and another Original batt ) , when I finish upgrade to WM6 . But it can turn on by extension DC 4volt feed up and working well with no battery icon.
Anyone have solusion ???
i-mate JAMin
Hello,
the i-mate JAMin is not a 3G device, and i think that the reason that you dont have the battery icon any more that used to show on the device before upgrading to wm2006, which is not safe as you might loose some of the main parts of the original operating system that the device can handle, but the 2006 is not designed to work on the wm2005 devices, i think what you can do is to try to hard reset the device for two or three times and if needed try to install the operating system from the original company of the device (I-MATE) but when you try that make sure the device is in the boot loader mode. and good luck
Thank for your answer but now my i-mate get stuck screan ,affter upgade around
did you CID unlocked your G3 Jamin before upgrade to WM6 ?
try to reach to Boot loader and Downgrade with WM5 and test your device with battery
JAMin
i think you should try hard resetting the device to try to get back the previous wm2005, to hard reset Press and hold continuously at the Comm + Camera buttons then press the power button once, even it didnt work from the fist time try it once or two times. good luck
Related
Hi All, excuse this, I have tried everything else including the i-mate site who leave alot to be desired ( I was goin through the process of upgrading my Jasjar to WM6 & did not follow the instructions asa you do... My Jasjar has now totally reset itself back to the basic screen without windows installed so it seems, all I get is a blank unpowered screen with v1.00 at the bottom, have tried plugging it into my USB port, which just says it does not recognise it. I have also lost my WM5 CD, so can't even restore from there.. can anyone advis me what to do next.... i'm pulling my hair out (what little of it I have )
Thanks
NP
Just restart the OS load, try in with the MaUpgradeUt_noID.exe , and that is it!
Oh happy days!! Logged into the main screen this morning & there it was, reseting your device from bootloader screen.... Now to upgrade to WM6
Where would all of us Mr Average PDA users be without you guys!
Thanks
After I tried to upgrade the rom to WM6, my JAMin got stuck at bootloader. After that, I tried to flash WM5 roms without success and suddenly (after a reset) the screen became white with some horizontal and vertical lines constantly moving. I discovered that it was only the screen that was garbled as it still connected to PC, so I installed (without seeing anything on my JAMin) the NVID ROM trying to restore it. It installed sucessfully, but the screen remained garbled with the white background and random lines. I know it was sucessfully installed because I heard the typical "welcome" sound before configuration.
Do you know any way to restore the screen? Or must I send it to I-Mate to repair?
You can try and reattach the screen cable to the rest of the device, but this will boid any warranty you have, and may damage your device further. If the device is under warranty, I would suggest flashing the ROM the device came with (unfortunately the FTP server is down at the moment, so it might take some fishing around for) and sending the device back to get repaired properly.
mpmf said:
After I tried to upgrade the rom to WM6, my JAMin got stuck at bootloader. After that, I tried to flash WM5 roms without success and suddenly (after a reset) the screen became white with some horizontal and vertical lines constantly moving. I discovered that it was only the screen that was garbled as it still connected to PC, so I installed (without seeing anything on my JAMin) the NVID ROM trying to restore it. It installed sucessfully, but the screen remained garbled with the white background and random lines. I know it was sucessfully installed because I heard the typical "welcome" sound before configuration.
Do you know any way to restore the screen? Or must I send it to I-Mate to repair?
Click to expand...
Click to collapse
Hi frd,
I have exactly the same problem!
Nothing , only the f*** white screen!
I can browse the device via active sync, can rcv calls but the white screen.
I have checked the ribbon connector of the LCD and make reflashing some ROMs but nothing.
I still wondering is it hardware or software problem!
Please let me know if you have progress!
Thanks
G.
Try to replace LCD module, I think thats right way.
It will be a hard ware problem. Probably the ribbon cable as the screen is showing something so it must be working at least a bit.
Hello,
i have the same Problem with my QTEK S200.
First i changed the Rom and it worked perfectly for two days.
Then i had to change my Sim card and after that the problem came again.
I tryed a lot of times to reflash the rom but the problem persist.
How can it be that it worked again for some days ?!
is it the touchscreen of the lcd unit i have to replace ?
is it possible to do it by my self ?
thanks for your help !
Hi everyone.
I had a similar problem an hour ago (Qtek S200 G3):
I Upgraded to a 6.1 rom and then to another, after that my device was stuck in bootloader(3 colour screen). Any 6.1 rom that I tried would install, but after installation device always boot in to the 3 colour screen.
I tried this original shipped rom http://files.mail.ru/HZUAH1 (it's WorldWidwEnglish) (to download just click the link "скачать" or the file name RUU_Prophet_220734_2207114_024721_QtekWWE_Ship.exe
) and it installed!!! It TAKES A WHILE TO INSTALL!!! But it worked!!!
May want to try it.
Hope this helps.
hello,
picture on screen was immediatly clean again ( bootload image ).
it was impossible to change the rom because i have a G4 model.
i flashed the rom with another french rom for G4 and it worked perfekt.
now i tried to remove the battery again for 3 seconds and now i have the same problem again. really strange ....
i tryed the same procedure again but no success.
I reinstalled differents rom's again starting always installation from bootloader.
After about 10 new installations i've clean picture again.
now i'll not put off, restart, or take of battery till one of you know what's the problem.
Thank you for your help !!
are you guys sure its not an intermitant hardware problem, it sounds like it to me. if yu were able to get a clean picture for a short time and now its white again, it cannot be the rom? As for replacing it, nothing is impossible and there is always ebay and google
QTEK S200 G4 CID unlock
How can I CID unlock a device that need´s that to upgrade the Rom?
Is there already any program that , Lockwiz dont do the job, can performe the unlock?
Thank you.
For G4 CID unlocking, you need to user Hard/Soft SPL.
same problem
my imate jamin got the same problem. it happens only and only when I remove the battery and when I leave it to charge for 1-2 days the LCD works again and show clear pic. any suggestion? activesync and &... are all ok!
Well, i upgraded to windows Mobile 6, but haven't removed the batterie anymore.
But i'm able to put it off now, what was impossible before.
I am posting this here since there seems to be way too many threads around here all saying the same thing diffently yet in NO clear way that everyone can understand. I spent 2 days trying to recoved a Prophet from a bad flash.
Symptoms
Prophet stuck in Bootloaded (Tri Color Screen)
Prophet stuck in 2nd Splash (Usually Your providers Splashcreen)
Solution Read as (This is what I did to fix it)
Download a WM5 Prophet\Wizard Official Rom (I still own a Wizard so I used the K-JAM_WWE_216901_2169101_020710_ship rom, the devices are very similiar concerning chipsets with the hardware keyboard seeming to be the biggest difference)
Extract the Rom (if it is distributed in an exe format with a tool like Winrar or 7zip)
Download the Prophet Tools Light package and extract to any folder . This contains both G3 and G4 RUU's (I can confirm this worked on a G4 Device)
Place the Official nk.nbf in the \Utils\Flash folder
Drop the phone into bootloader (Tri Color Screen) mode and connect to PC via usb.
Allow a few seconds for the usb connection to settle and run the RUU specific to your device.
DO NOT TOUCH the device or PC at this point. If your pc is a tad slow, go make some coffee and watch an episode of Big Bang Theory
This should now give you a shiny new (or old ) rom that is bootable which will allow you to upgrade your Prophet to any of the pretty WM 6.1 roms available.
Just a little tip:
If you are worried about messing up the device again use Alternate "Lazy tool" by dioxda. Its easy and it works !
I couldnt make this process any clearer if I tried
heeey...sorry but after this my prophet go death... i cant turn it on, and i dont know how but it seems that i cant charge it no more...
is death... can anybody help me how 2 fix this?
P.S.sorry if my eanglish is not very good.
specto13 said:
heeey...sorry but after this my prophet go death... i cant turn it on, and i dont know how but it seems that i cant charge it no more...
is death... can anybody help me how 2 fix this?
P.S.sorry if my eanglish is not very good.
Click to expand...
Click to collapse
Strange this worked perfectly for me, but when I tried updating to a different rom I got the same problem you are facing now. Just a quick flash on the screen and blue and red LED flash. If I plug it in it just sits there flashing the whole time. I am looking into this as soon as I get a solution I will post it here. Any help guys ?
cornelha said:
Strange this worked perfectly for me, but when I tried updating to a different rom I got the same problem you are facing now. Just a quick flash on the screen and blue and red LED flash. If I plug it in it just sits there flashing the whole time. I am looking into this as soon as I get a solution I will post it here. Any help guys ?
Click to expand...
Click to collapse
Recovery
http://forum.xda-developers.com/showthread.php?t=401326
If at any stage your Prophet fails to start properly or can only enter bootloader follow this:
* Download and install the latest version of ActiveSync (Google for it)
* Download and unzip an AKU2.2 (No Vendor) ROM for the Prophet-any AKU 2.2 will do-from [here | ftp://xda:[email protected]_NVID.exe] or [here | http://wiki.xda-developers.com/index...=Prophet_ROMs]
* Within ActiveSync DISABLE connect through USB (Tools->Connection Settings->Uncheck Allow Connect through USB)
* Put the Prophet into bootloader mode (hold the camera button and insert the stylus into the larger hole next to the power socket)
* Plug the Prophet in via USB
* Run the RUU specific to your device (G3 or G4) from the AKU2.2 folder. If there is only one RUU, use that.
* When it has finished: disconnect the Prophet, and then re-enable the connect through USB in actyivesync before reconnecting the device.
==> if success, will going back into WM5 and then u can use the Lazzy Tool, look at http://forum.xda-developers.com/showthread.php?t=353547
choose WM 6.1 ROM, after u doing that step, u already done with the WM 6.1 SEMOGA SUKSES!
yes it works again ...
Help, please?
Hi guys,
I have a slightly different problem. When I turn on my Prophet, it is in bootloader mode, so I take out the battery, leave for 3 seconds, put the battery back in, turn on the Prohpet.
Bootloader is displayed
Plug into PC with Active Sync 4.5 running (USB disabled)
Windows makes the 'new hardware connected' sound
RUU shows USB in bottom corner
Run the NVID no vender ROM,
Agree to first screen
Agree to second screen
Click Next
Prophet turns off
Windows makes the 'hardware disconnected' sound
Argh
No Prophet, no phone - incommunicado!
When I turn the prophet on now, I just get the bootloader, then it turns itself off after 10 seconds.
Could it be a low battery? - How do I charge it? I have left it plugged in to the power all night!!!
Could it be a faulty phone? - I have been having random resets over the past 3 weeks or so and thought that it was the WM6.1 rom installed, so was trying to put WM5 back on to see if that helps. - I am beginning to think there may be something wrong with the device?
I am trying a few more things from this forum before giving up and buying a new windows smartphone!
Any help would be apreciated!
Regards Mike
Guess it could be a power issue. - I got further just now by using a powered cradle instead of just a usb cable, but still reset at 80% complete. Will leave the phone charging using a wall charger only for an hour and see how i get on with that!
Its Fixed!
Ok,
So it turned out to be a low battery. - I charged the Prophet up for 1 hour and then ran the re-flash and it worked perfectly.
Now I just need to get the Orange rom back on it so its back to normal - Not faffing with WM6.1 - will stick to WM5 as its much quicker and works!
Maybe I was a bit too fast in posting the problem!
Thanks
Mike.
I have a problem with my I-Mate JAM, It loads the OS.. but after everything Installs it converts to the BootLoader screen, and remains unuseable.
If I rest the phone, it loads straight to the Bootloader screen, but if I take off the Battery cover, leave it for a few seconds, then replace it and turn the phone on... It will load the OS setup again, but go back to the BootLoader.
So how can I fix this, and what must I do? Please help me ASAP. The Rom/OS is Windows 2003 SE.
Thanks
Sikuri
Good day.......
I am mailing out of real frustration.
I don't know if this is allowed.
I collected a cingular 8125 from a friend in the UK.
I noticed on starting up that there was Tmobile screen first before the windows mobile screen starts. I had no problem with the fone until i realised that i couldnt connect to my local networks GPRS service (who uses a phone that can't browse)
After scanning thru the site, i decided to flash the phone with Crasing's WM6.5 ROM after doing a HardSPL and i could browse and it was the perfect phone apart from the fact that it was real slow and hangs attimes.
It got worse so i got fed up and decided to revert it back to the original ROM and sort the browsing stuff with a network fix that someone on this site had told me.
I reverted the hardSPL and on installing the Tmobile ROM, it brought out an error message, tried with the Cingular ROM same thing.
So i tired reflashing by using a software called Flash Center and it started and stopped at the 1%.
Restarting my phone just shows me the bootloader screen and i have been battling it constantly for 3 weeks but to no avail
I have read almost all forums here, done almost all they ask to do, but nothing.
The only ROM that worked on it is the WIZARD love ROM but it using exactly 21mins to start up. Thot of downloading Faria/Molski WM5 ROM (cos i sorta prefer going back to WM5) but the links for their downloads are dead.
Please help/direct me to where i can see help cos i really need the phone like 2 weeks ago. I am most definitely depressed now.
Thanks.
Check here for all HTC Wizard WM5 OEM shipped ROMS. The one for Cingular is listed in there.
http://forum.xda-developers.com/wiki/index.php?title=HTC_Wizard_Windows_Mobile_5.0_Shipped_ROMs
You say the phone is a Cingular (G4 DOC version). Does it look like this one (click link ... http://www.brighthand.com/assets/4811.jpg ) with the Cingular logo on top left, etc?
Did you require the HardSPL to be able to flash to new ROM, or did you just use the SIM / CID unlocker using the Wizard Service Tool (note the Wizard Service Tool will only work for G3 DOC type device, not the G4 DOC devices)
You said you also removed the HardSPL. If you removed the HardSPL, then you can only flach the OEM ROMS (i.e., if yours is Cingular, then you can only flash the Cingular Stock ROM ... check link above and use Cingular 2.25 (click here ...
... http://www.4shared.com/file/BJUEhCC9/RUU_Wizard_Cingular_8125_WIZCN.html )
First do a battery pull, replace battery, then start device in bootloader mode (i.e., press and hold Camera button on side, then using the stylus press and release Reset button on same side. Do NOT power up the unit by trying to turn on using the Power button on top). Take note of IPL and SPL version that shows up on Bootloader (3 colour) screen. Then plug in USB and try re-flashing with Cingular OEM ROM.
After successful OEM ROM you can then try HardSPL again and re-flash to other ROMS. There are plenty of cooked WM5 and WM6.1 ROMS out there. The WM6.5 is too much (I think) for these devices. A neat clean simple WM5 or WM6.1 with overclocking works very good.
Regarding your settings for ISO, GPRS, WAP etc. you can look for a Netwrok Wizard cab file, and install ( heres the newest I could find ...
http://forum.xda-developers.com/attachment.php?attachmentid=121023&d=1223800573). This will install 6 files into the root Windows directory of the phone. Reboot the phone and you will notice the Network Wizard icon show up in the Settings/Connection control panel.
One of the files it installs is called provision.zip. You will want to update this by copying the following to the windows directory overwriting the old one. This contains all the settings for your phone. Once you copy this over, click on the wizard in the Connection Settings control panel, and it should give you options for Country and Cell Phone carrier/provider. Click away and it shoould automatically set up the correct info for WAP, GPRS, ISP, MMS, etc.
Good Luck. Let me know what happens.
WOW
Thanks for the response
I used the HardSPL to flash the new ROM.
I removed the HardSPL and the Olip in my IPL was changed back to the 2.26.0001
I tried the cingular 2.25 ROM but it says it wasn't meant for the device and most times the RUU doesn't recognise the phone. Tried the Tmobile 2.26 same thing.
Also used crossbow WM5 AKU2.3 and AKU3.3 ROMs they worked but fails at 96%
The only ROMs that worked is Wizard Love ROM but it spends about 20mins to get to the part where it asks you to align screen and it doesn't move from there
Thanks for the info on the WM5/WM6 also the network wizard cab file. Really hope that phone works
I'm a pretty desperate guy right now cos i use the phone to trade and money is moving, she(money) is a *****
WOW
Thanks for the response
About the pix you reffered to? Yes thats exactly how my phone looks like
I had used the HardSPL to flash the new ROM.
I removed the HardSPL and the Olip in my IPL was changed back to the 2.26.0001, SPL 2.26.0001
I tried the cingular 2.25 ROM but it says it wasn't meant for the device and most times the RUU doesn't recognise the phone. Tried the Tmobile 2.26 same thing.
Also used crossbow WM5 AKU2.3 and AKU3.3 ROMs they worked but fails at 96%
The only ROMs that worked is Wizard Love ROM but it spends about 20mins to get to the part where it asks you to align screen and it doesn't move from there
Thanks for the info on the WM5/WM6 also the network wizard cab file. Really hope that phone works
I'm a pretty desperate guy right now cos i use the phone to trade and money is moving, she(money) is a *****
PS: My IPL/SPL is 2.26.0001
OK. Good info.
Not sure how you did it but somehow you managed to get the T-Mobile IPL/SPL on it, and yet it still recognizes it is Cingular. For one reason or another one aspect does not let the other load and vice versa. ????? Hhhmmmnnn ????
Here is what I would try.
1) I have attached a zip file called SoftSPL. Inside I have made an image file nk.nbf, which contains ONLY the 2.25.0001 IPL and SPL for the Cingular 8125.
Unzip this folder to your Desktop and then try to run only the "newromupdateutility_wizard_noid.exe". Remember, start the phone up in bootloader mode, connect via USB then run the "newrom...exe" file. If you get an error right away saying this is not the right update utility for the phone or something like that, then start over ... i.e., disconnect phone, pull battery, start phone in bootloader mode,reconnect via USB, but this second time try using the one called "2.exe". I found sometimes when I flashed ROMS the first one did not work and the second one (2.exe) did for me.
IF this works, once you get the 2.25.0001 IPL and SPL showing on the bootloader screen then start again (pull battery etc. same as above) but then re-flash back to the original Cingular OEM 2.25 ROM that you tried earlier (the original RUU_Wizard_225111_22511102_022511_CWS_WWE_Ship_1.exe). Try this and let me know how it goes.
If and when you get it back to the original Cingular ROM, if you get to this point, you can then start back like it was when phone was "new". It will still be SIM unlocked so you can use any carriers SIM card but you cannot flash other ROMs.
If you are going to try other ROMs, re-apply the HardSPL, but make sure you only use ROMs that have been cooked, say they are safe for G4 devices and do not have IPL/SPL in them. This means when you have it HardSPL'd you cannot, or should not use other carriers OEM ROM's such as T-Mobile 2.26 or 3.08.
Lastly, if you do like some of the "extra's" offered with WM6 or higher and do not like a slow phone and want to keep it fast like a WM5 ROM, then stick to either WM6.0 or WM6.1, clean (or what they call Vanilla) ROMs.
Good Luck. Give feedback of how it works out for you and pay attention to errors and messages and IPL/SPL etc. for reporting back and I can help you a little more.
Another thanks again.
I really owe you if and when my phone is finally done cos i think i am getting there.
But i successfully changed the IPL/SPL but on flashing the cingular ROM it says the RUU cannot see my phone and once it sees that it says the update utility cannot be used for my phone.
So what next?
Maybe the ROM is not the right one but i ensure it was meant for g4 tho"
Tried MUN-RUU but to no avail
Eagerly waiting your reply.
Thanks again
OK. YES. You are getting there.
You say the phone is now IPL/SPL 2.25.0001. It shows this on the 3 colour bootloader screen?
What did you run in order to flash; did you run the "newromupdateutility_wizard.exe", or "2.exe", or did you need to run the "START-sSPL.exe" to flash th nk.nbf file I made? (I don't think the "START-sSPL.exe" works from the bootloader screen...phone has to be booted to working status).
Here's what is next. I made a new nk.nbf which is the Cingular 2.25 OS, splash screens and 2.25 radio only. I removed the IPL/SPL and the Extended_ROM, and cooked this back to nk.nbf.
Download it from here .....
http://www.fileswap.com/dl/7WhstX82/nk.nbf.html
..... and copy this to the folder you made of the SoftSPL earlier (overwriting the other nk.nbf - you may want to save that as a back up)
Now try flashing this new nk.nbf again as you did for the IPL/SPL.
If it works, then let the phone boot up completely. Check it out. And then you can run the RUU for the original Cingular OEM once the phone is booted to get it back to Cingular OEM state (full IPL/SPL, OS, GSM, Extended_ROM, etc.)
From here (if you make it) then any further flashing of ROMs, you will want to flash G4 safe ROM's, and you can do this using the SoftSPL folder. Copy the nk.nbf from the custom ROM you want to flash into the SoftSPL folder and run the "START-sSPL.exe" with your phone connected (not in bootloader mode, has to be completely started up and recognized by ActiveSync, but you do not need to establish partnership ... just skip/cancel that part and phone will connect to ActiveSync as a "Guest").
Good Luck. Let me know how you make out with this.
Just to answer your questions.
I ran the "newromupdateutility_wizard.exe"
Would follow thy new instruction sire and get back to thee.....lol
Thanks again.
I am not here to say "Yipee, its done'
But rather to say that the universe, cingular and the god of communication might have just conspired against me.
Just when i think i would finally get my phone working after 3 weeks, a 2 yr old kid took my batteries and only God know where that batteries is now.
Tried to buy a new one but all i get is "Wow! that a pretty old uncommon phone here"
I intend to use an ac to dc converter and when i am done i would give you the feedback
Thanks
PS: Just wanted to give you the heads-up
So i found the battery early this a.m.
Flashed the phone with the ROM you uploaded and it was succesful but on starting it i get a green screen and its damn slow and doesn't even pass the spot where you are asked to align screen (i really do think that nothing happen and its still the Wizard Love ROM that its still booting into)
So I am still stuck?
Hmmm....
OK i guess there might be a psych diagnosis for what i am doing (posting excessive replies without any respond)
It just a worried person.
So i kept re-trying to flash the ROM on my phone about 2ce.
Then i noticed on the 2nd time at about 86% the phone seemed to restart itself into bootloader mode about 2-3X, so i thot the battery was running out. Decided to take it out and get it charged.
On plugging the battery back to the phone all i got was a white screen and starting it on bootloader mode OR hard-resetting still gives me that white screen. On removing the battery the phone flashes like once or twice.
Is this the end? The phone has brought an apocalypse on?
Been doing a lot of browsing for clues but nothing tangible yet.
God smiled on me and the phone started
Got the ROM you gave me flashed and its really refreshing to see the Windows Mobile logo again
But i am stuck at the align screen tho'
I tap and nothing happens unless i drag the target and it just moves around and get back to the original spot.
Thats the latest pal.
OOPS. I did not read all .... your posts ... I just answered your post at the end of the last page. Did not see these last 2.
This is a good sign that you get past the initial boot splash screens and make it to the Align Screen ... soft reset the phone again and look at the IPL SPL that shows on the screen. Is it 2.25.0001 or 2.26.0001?
If 2.25.0001 then let the phone boot up to the Align Screen (and if you cannot get past this then just leave it at this point). Plug back into computer and now try to flash Cingular OEM ROM 2.25 that you tried earlier using the stock file.
If this doesn't let you flash for the same reasons as before (i.e., Invalid RUU tool or Not correct operator) then extract the nk.nbf from the Stock Cingular ROM (right click on the Cingular RUU OEM exe and select "Extract here ...".) then copy the nk.nbf over to the Soft SPL folder and use the START-sSPL.exe and flash this way. (you can delete the rest of the files from the Extract process.
Good Luck. Let me know the IPL SPL you get.
I know my posts are getting sickening but i am really desperate.
Got some info about how to bypass the align screen online but couldn't get my phone to boot anymore.
Soft reset/Hard reset/Bootloader mode: All of it just shows a white screen and nothin more.
Any ideas?
PS:The last time i could start the phone the IPL/SPL was 2.25.0001.
Just want to add this cos i just noticed it:
1. Sometimes tapping the Camera button alone puts the phone on (tho' it shows that annoying white screen)
2. On connecting the phone to a PC the PC recognises it even tho' its off and once i put it on and that annoying white screen comes on, the PC gives the same sound as when a USB is detached.
Hope these info would help.
I"m really getting depressed now. Hope's looking dimmer.
OK. I am now suspecting that you may also have a battery problem. How old is the battery. Could be the battery no longer has enough capacity. It may charge but only hold a charge for very short time and voltage may be too low. Maybe enough power to keep some of the electronics "awake" but not enough to drive the LCD.
It is now IPL/SPL 2.25.0001 so it should be able to flash the Cingular OEM ROM. You may want to try a different battery. Other than this, if not a problem with the battery then I think maybe phone itself is coming to an end.
I would try the battery route, making sure you have a good power source, and then try to flash the stock Cingular ROM.
You can still get these batteries on ebay and phone as well. If you are going to spend any money then maybe instead consider a newer model phone on ebay. (if you are patient you can find very good deal ... I got the T-Mo MDA Vario version of the Wizard (WIZA200) for $25 plus shipping, brand new with a carrying case. It was an estate item from a salesman who passed away and phone was not used before he passed on. One man's misfortune, another man's luck. I am now selling this on ebay plus memory card and earphone here ... http://bit.ly/hDHxrW. I have two more on sale at ebay here... http://bit.ly/eV0zZh ... and here ... http://bit.ly/gLIiKh. I am selling 3 and I have upgraded to Touch Pro 2. Go with AT&T version as this can beused world wide on 3G in North America and is quad band GSM for use in rest of world)
WOW
Thanks Bud
I would change the batteries and really don't mind buying another one but the only problem is i am not in USA nor Canada except i give an address in the US to send it to.
PS: Got to the links and it was a bidding process that was over by the time i got there. If anything opens up you can holla at me.
Would get back to you if there are any new developments
WOW
Thanks Bud
I would change the batteries and really don't mind buying another one but the only problem is i am not in USA nor Canada except i give an address in the US to send it to.
PS: Got to the links and it was a bidding process that was over by the time i got there. If anything opens up you can holla at me.
Would get back to you if there are any new developments
Cheap battery on ebay ..
http://cgi.ebay.ca/New-Li-ion-Batte...652056?pt=PDA_Accessories&hash=item5d2d297c58
http://cgi.ebay.ca/Battery-HTC-Wiza...163910?pt=PDA_Accessories&hash=item45f7ebb846
Phone
Wizards
http://cgi.ebay.ca/HTC-MDA-Mobile-S...0528835033?pt=Cell_Phones&hash=item4cf50dc5d9