When I install Pocket Bluetooth Tools 1.1.0.0, and set the timeout option off (ie, leave BT on all the time), my iMATE (XDA II) never turns off. If I use the timer feature (auto off after 60 seconds), it turns off correctly.
Anyone experience this or know how to work around it? 1.0.1.2 works fine, except that with my BT800 headset, it doesn't properly answer the calls on the headset, so I must use 1.1.0.0
Help!
Thanks.
-Kevin.
I dunno wuts wrong with my universal (it's JasJar Actually)... I have a Cadillac and it doesn't connect with car's bluetooth.. it always says connection faliure... same goes with all pocket PC's I tried
While other phones.. Nokia, siemens, sonyericsson does connect...
Wuts the problem?
This will probably be because of the fact that your car kit only supports the "Hands-free" profile. I have a T-Mobile MDA Pro (also JasJar make) and have the same problem. As long as Windows Mobile only supports the "Headset" profile we won't have any luck.
I have read that M$ is planning a WM5 update/patch that adds Hands-free profile support, but I haven't seen any releases out there that include this.
Hi,
I use a BlueTrek earpiece (bluetooth) to enable handfree calling with my Qtek9100. I Also use TomTom Navigator.
When TomTom starts it enables the BlueTooth connections (if not allready active). This is usefull since I use a BlueTooth GPS with TomTom.
However, if I exit the TomTom Navigator application it is also disabeling BlueTooth, resulting in loosing the connection with the earpiece.
Does anybody know if this can be changed?
Perhaps a registry key I can change to solve this small, but annoyng, problem.
Gert-Jan
Turn on bluetooth before you start TomTom, then when you quit it should stay on. Does on my xda IIi anyway
The same on my magician. TT5.1 returns BT in the state it was before starting TT. TT5.0 however always shuts down BT on close.
Regards, M
I tested this last week, but came to the sam conclusion.
No matter what the state of BT, TomTom always disables BT on exit.
Gert-Jan
Ditto with my XDA2i running TomTom5 with a Qstarz BT-Q880. Slightly annoying.
However, if I press one of the hard buttons (such as the Contact List button), when the new window is brought up TomTom is minimised. Then, I can Switch (from hfrmobile.com) to Close All - and while this disconnects the GPS device, I've doublechecked and it doesn't disconnect my bluetooth headset, nor does it turn off the Bluetooth itself.
So, that in itself is a quick-and-dirty workaround hack, but I've not come up with any other solution thus far. Currently scouring the registry and the configuration files (what few there are) for a fix - it may be that someone with infinitely more coding ability needs to hack the TomTom .exe to disable this switchoff, though that's no mean feat.
You will probably find that if you reconfigure your GPS reciever in the Tomtom preferances as an "other wired receiver" select an appropriate baud rate, then select a Bluetooth com port, it will still work with a bluetooth GPS receiver but will completely leave your Bluetooth alone.
This does also mean it wont start it automatically if it's not allready on.
That doesn't work - the only way my Qstarz will work is if I configure it as Other Wired NMEA GPS and then run it on Bluetooth COM6, setting the baud rate appropriately (the Qstarz will accept any rate from 4800 to 115500 anyway, so that's rather irrelevant). Even if it's set as other wired GPS, the bluetooth is still disabled upon TT exiting.
This is also the info advised by the TomTom website if you're having problems getting your GPS to run with the software, so I'm guessing it's the only way. I'll have another look round the TT web site when I'm not so pushed for time.
What Tomtom version are you guys using? After a little play with mine I can say that with GPS setup as a bluetooth device. If bluetooth is on when I start Tomtom it stays on after I exit.
I use version 5.2 for Pocket PC
Well, small update - after having TomTom pop up the Bluetooth Manager box every time it starts up, and asking me which device I'd like to use as default, I managed to select the Qstarz Serial Port Connection shortcut which I created (had to manually create the link after setting up the device pairing) - I checked the option to Use this connetion by default, and now TomTom leaves the Bluetooth turned on after it exits!
Smashing stuff, means I can now use my headset and TomTom simultaneously in the car.
This is with TomTom 5.000 (4890) with GPS driver v1.20 and using the Great Britain Plus Map (v571). Bosh!
I get something different on my QTEK S100. When the QTek starts receiving the GPS signal (via bluetooth), TomTom freezes the screen for about 2 seconds and then closes TomTom.
Any ideas about this problem?
Is it because I had "MagicButton" installed? I uninstalled it, did soft reset... but the problem is still there. I can I know if it is MAgicButton doing that?
Thanks
DoubleW
Hello all,
I recently purchased the TD2 and I encounter a problem with its BT SAP functionality with my car (VW).
It connects and works ok, but when I turn the ignition off, remove the key and the phone disconnects from the car, it doesn't reconnect to the GSM provider again. I have to go to Settings/Communications and turn the phone off and then on again in order to reconnect.
Has anyone encountered a similar issue?
HTC support told me that it seems the car BT is not releasing the SIM card properly. The thing is that my old prophet with a cooked WM6.1 rom (don't remember which one right now), worked fine, without any similar problem.
Any ideas?
TIA.
PS. Ooops, sorry, think I posted on the wrong topic.
Hi all,
I am trying to use the factory bluetooth integration in my car, and from everything I've read, it requires SAP (or rSAP?) to work properly. I've never had trouble pairing to the bluetooth module, but the car still insists there is no phone.
After messing with it yesterday and installing SAPSettings, I can hear the speaker of the phone in the car's audio, but no microphone, and it still says "insert phone" in the car's phone menu as apposed to downloading the phone book and letting me dial on the screen.
The phone lists the SAP profile among many others, but if I go into the settings of the car's bluetooth connection, it only lets me choose "Hands Free", with an on/off checkbox. It seems like thats what it sensed was available from the car, and offers nothing else, but I'd like to force SAP instead.
Car: MB E-Class
Phone: Sprint HTC Touch
OS: WM 6.5
Thanks!
I'm going to put the official windows mobile 6.1 on it to see if it makes a difference.
bluetooth is a long list of various profiles
problem is that devices only need to implement 1 or 2 to call themselves
bluetooth devices and no if the maker of the bluetooth stack in both ends
didn't implement a profile you can't force it
I have this problem trying to get my HD to connect to my landrover freelander 2 hse. I can get it to connect to the phone, but cant get the call to play thru cars speakers.
Dont bother with winmo 6.1 or official rom, just doesnt work at then (cant connect).
Only way i can get it to work is with winmo 6.5 (manila 2.5) (profiles must have newer or more stable settings). Only thing i have to do then is to make a call (normally voicemail) turn privacy on, then off again and voila it plays thru speakers.
Downside is i have to do this everytime i start the engine.........
Now that probably doesnt help you much but you will probably find from your car manufacturer that you device is not supported with you cars handsfree bluetooth kit.
the only one fully compatible with the freelander 2 is................. an phone