Related
Ok, I have a BT200 that is working very quirkly with my i-mate. Sometimes the phone transfers the call to the headset, sometimes it doesn't. After deleting and recreating the bond, it works, but not for long. Anyone have one of these setup and working properly? Is there a trick to it?
Also, does anyone know if other headset drivers exist that may work on the i-mate that would allow you to hear all audio (not just phone) through a bluetooth earpiece?
Figured it out?
Ok, I've finally pinpointed that it works fine until I turn off the jabra headset, then when I turn it back on, I have to go through the entire thing again of re-creating the bond, etc..
Anyone know how to avoid having to recreate this everytime I turn the headset on or off?
I don't now ... but i have also jaba 200 and the MDA II is must arrive...
well please chip us informed
Thanks
DenisJ
I have the same combination and have also observed the same hassles.
It seems to work when I turn the BT headset function on the MDA off and on also. Thsi seems to result in a rebond.
Exact Steps
TBD,
If you could post the exact order of the steps you take to turn on / off the headset, I'd appreciate it. Right now, I'm doing the following:
1. Finish BT Headset Call.
2. Disable Bluetooth Headset Mode on Phone.
3. Disable Bluetooth on the phone.
4. Hold button on JABRA to turn it off.
Then, attempting to...
1. Hold button on JABRA to turn it on.
2. Enable Bluetooth on the phone (Set to "On" or "Discoverable")
3. Enable Bluetooth Headset Mode on phone.
4. Attempt to make call.
So if you could posts steps like that, i'd appreciate it. Also, do you set your bluetooth to "On" or "Discoverable"? Do you ever turn off the Bluetooth Radio completely?
Thanks,
Jon.
Yup me an all. I too have the Jabra BT200 and have the same problem. Providing you don't switch off the headset or go out of range your ok, but for instance when you leave the headset in the car and take the XDA2 with you you have to create a new bond to use it again. AHHHHHHHHH!!!
Shame cos so much else has been sorted on it.....and more. What a piece of kit!!
SOMEBODY HELP!!!
OK, so here is the sequence, which seems to work (for me).
1) I set everything up as per instruction. creating the bond between the Jabra and the MDA II.
2) Before (or after) I turn off the Jabra I disable the BT-Headset on the Today-screen.
3) Then I turn the Jabra on again and wait several seconds before enabling the BT Headset on the MDA II.
This seems to work most of the time, though the hint regarding going out of distance might explain the instabilities I have still observed. In any case, using the BT-Headset ON/Off on the Today-screen seems to resync things most of the time and get the Jabra up and running again.
Hope this helps and always open for new ideas
I have been a bit impatient after turning the BT headset on. I'll try it and let you guys know.
I may have been a bit optomistic. :roll:
Today I observed that sometimes the Headset reacts very late. Consequently you miss half of the call. Seems to be an XDA problem.
As for my XDA II with Sony Ericsson HBH-65, after creating the bond, before i turn off the BT headset, i turn off BT profile and BT on my PDA, then turn off the Headset.
If i want to turn on the headset, i activate BT on my PDA, then BT profile, the the headset. Sometimes in teh day headset seem to lose the bond and cannot use the BT to call or whatever. I tried turning on/off BT on my PDA, did not work. Turn on/off headset, it worked. So for me most of the time is my headset causing the problems
i am having the same problem with the new moto bluetooth headset although i have experienced no problemzs with the se hbh-30 bluetooth headset....i can turn off and transfer calls without any impact on teh bonding
Jabra problems
I've had similar problems on a boring old Nokia 6310 with my BT200. In the end, all I could do was find the 'automaticly reconnect' option on the Nokia. during calls, the link is allways fine, but between calls, when I guess one end or the other goes to sleep, the link will drop out, and then instantly reconnect. This happens around 2 or 3 times an hour.
Is there a 'automaticly reconnect' option on your XDA?
All the best
James
OK, I finally sacked my Jabra 200, because of its instability. What use is a headset, that doesn't repond when a call comes in? :evil:
I bought a B-Speech from B-Data yesterday and it seems to be working much better :lol: .
Nokia HS-3w headset with XDA II
Well! I am using the Nokia HS-3W Bluetooth Headset with my XDA II . I can pair up two devices and use it for only ten minutes :twisted: . After that, the headset will off(goes to sleep) . I Have to turn on the headset every ten minutes. I ask the dealer about the problem. They told me this headset work fine with Nokia's phone. They told me , there is three color on the light. Red light will flash when you turn off the headset. Green Light will flash when you turn on the headset up to ten minutes, if cann't find the phone devices , it will goes off.White light will flash, when the headset connected to the phone. When I turn on the headset, I just can see the green light only.But, if someone call me or I make a call ,the white light will flash.After the that the headset will flash the green light again for about ten minutes and goes off. Can anyone help me with this problem? Thanks!
@[email protected]
Hi, I will like to ask how your headset B-Speech is working.
It works 100%?
I have a jabra 250 with the same problems as BT200
Please let me know
Regards
JoseF
The B-Speech Headset is working OK, however it doesn't solve the problems with the Microsoft BT-stack.
Some observations, probably also applicable to the Jabra:
:?: When you go out of range with the headset, it will probably not reconnect automatically (but how do you know)
:x On an incoming call, the XDA may be very slow in activating the headset, so you might miss the call (seems to be tied into what the XDA s/w is just doing at the time
When you turn the Headset off, make sure to turn it off on the Today screen first. And when you turn them on, make sure to wait about 2 sec. after you turn the headset on before turning it on on the Today screen.
:idea: What seems to work best, is turning that Headset off and then on again on the Today screen. It usually comes back after that.
Mind you, it isn't the headset thats causing these problems. Its just that Microsoft botched the Bluetooth stack - probably the programmers had blue teeth from all the wine they were drinking!
I've found the out of range issue to be mute on my jabra 200. The only time the bond is broken is when the headset has been turned off. Or sometimes when it has been on charge.....
Strange........I use the Jabra BT 250 with the MDA II and have non of these reconnection problems. I f I turn it on and place a call (or receive) it reacts immediately.
However, I cannot use the advanced Headset Profile features of the Jabra with the MDA, but this is not the fault of the Jabra........
Could the people who are having problems and the people who are not having problems with their Jabra BT200's please post their version numbers of the Jabra BT200. You can find the version number on the boom going to the microphone. It will be 2 numbers and a letter, like 48A or something like that. I'm testing a theory that I think will help identify why some people work and some don't.
Thanks,
LouisK
Ok, the number on my Jabra Bt 250 is 44B.
A weird thing has happend to my Magician - Bluetooth, which I don't use very much, gets turned on whenever I call out. It seems like this started to happend after I fiddled around with BT tools (now uninstalled).
Any tips on how one can fix this?
the coz of Pocket Bluetooth Tools ,it turn bluetooth ON automaticlly when u call or recived call, if that bother you install the previous version 1.0.1.2... 8)
Yup, that's one of the settings - one of the better features - of Pocket BT Tools.
What is the advantage with that? For a headset?
yes
The automatic turning on of Bluetooth, is not a good feature, though it might be if there was an option of turning this feature off.
I found that the automatic turning on off Bluetooth uses up your battery power much faster as you never remember to turn the Bluetooth off.
huh ?
my bluetooth tools turn bluetooth off again after the time set for it to autoturn off you know that clock in the today part of bluetooth tools
if you play with a regeditor you can set the time 100% yourself
Hi,
I use a BlueTrek earpiece (bluetooth) to enable handfree calling with my Qtek9100. I Also use TomTom Navigator.
When TomTom starts it enables the BlueTooth connections (if not allready active). This is usefull since I use a BlueTooth GPS with TomTom.
However, if I exit the TomTom Navigator application it is also disabeling BlueTooth, resulting in loosing the connection with the earpiece.
Does anybody know if this can be changed?
Perhaps a registry key I can change to solve this small, but annoyng, problem.
Gert-Jan
Turn on bluetooth before you start TomTom, then when you quit it should stay on. Does on my xda IIi anyway
The same on my magician. TT5.1 returns BT in the state it was before starting TT. TT5.0 however always shuts down BT on close.
Regards, M
I tested this last week, but came to the sam conclusion.
No matter what the state of BT, TomTom always disables BT on exit.
Gert-Jan
Ditto with my XDA2i running TomTom5 with a Qstarz BT-Q880. Slightly annoying.
However, if I press one of the hard buttons (such as the Contact List button), when the new window is brought up TomTom is minimised. Then, I can Switch (from hfrmobile.com) to Close All - and while this disconnects the GPS device, I've doublechecked and it doesn't disconnect my bluetooth headset, nor does it turn off the Bluetooth itself.
So, that in itself is a quick-and-dirty workaround hack, but I've not come up with any other solution thus far. Currently scouring the registry and the configuration files (what few there are) for a fix - it may be that someone with infinitely more coding ability needs to hack the TomTom .exe to disable this switchoff, though that's no mean feat.
You will probably find that if you reconfigure your GPS reciever in the Tomtom preferances as an "other wired receiver" select an appropriate baud rate, then select a Bluetooth com port, it will still work with a bluetooth GPS receiver but will completely leave your Bluetooth alone.
This does also mean it wont start it automatically if it's not allready on.
That doesn't work - the only way my Qstarz will work is if I configure it as Other Wired NMEA GPS and then run it on Bluetooth COM6, setting the baud rate appropriately (the Qstarz will accept any rate from 4800 to 115500 anyway, so that's rather irrelevant). Even if it's set as other wired GPS, the bluetooth is still disabled upon TT exiting.
This is also the info advised by the TomTom website if you're having problems getting your GPS to run with the software, so I'm guessing it's the only way. I'll have another look round the TT web site when I'm not so pushed for time.
What Tomtom version are you guys using? After a little play with mine I can say that with GPS setup as a bluetooth device. If bluetooth is on when I start Tomtom it stays on after I exit.
I use version 5.2 for Pocket PC
Well, small update - after having TomTom pop up the Bluetooth Manager box every time it starts up, and asking me which device I'd like to use as default, I managed to select the Qstarz Serial Port Connection shortcut which I created (had to manually create the link after setting up the device pairing) - I checked the option to Use this connetion by default, and now TomTom leaves the Bluetooth turned on after it exits!
Smashing stuff, means I can now use my headset and TomTom simultaneously in the car.
This is with TomTom 5.000 (4890) with GPS driver v1.20 and using the Great Britain Plus Map (v571). Bosh!
I get something different on my QTEK S100. When the QTek starts receiving the GPS signal (via bluetooth), TomTom freezes the screen for about 2 seconds and then closes TomTom.
Any ideas about this problem?
Is it because I had "MagicButton" installed? I uninstalled it, did soft reset... but the problem is still there. I can I know if it is MAgicButton doing that?
Thanks
DoubleW
Hello,
I'm using an Atom with WM2005 and the BT headset R35 from i-tech. This allows you to control the wm player via bt. By starting the voicedial from the standard button on the BT HS, i encounter unbearable sound problems and the sound from MS Voice command 1.6 is not transmitted at all... I don't know why, but that's the case.
When I start the voicedial from my phone instead all the rest works perfectly via BT. Means, I can not use the standard button from the BT HS. Therefore my idea: Activate voicedial from a different BT button, there are enough, for instant the one that pause and resumes the wmplayer. The button also wakes the phone up.
Any idea if this is possible? can i change a registry entry to handle this event or use a tool, like the one to reprogram the hardware buttons???
Any experiences, or similar problems?
Cheers
Ellork
Hi,
I am using my HTC Touch Pro with an Opel Vectra built-in bluetooth carkit.
All functions, like browsing the address book and call registers, are working fine. However, at random times, my carkit reports no phone. When I then check my Touch Pro's bluetooth status, I see that it is has been disabled.
After manually re-enabling it, I can pair with my carkit for as long as it takes for bluetooth to turn itselves off again.
I've already tested with JETware, but that does not change anything. Also tried the universal broadcom bluetooth stack, but doesn't seem to work on the Touch Pro. HTC only comes with a standard answer that they don't support all carkits and headsets... Since the BT stack on the phone seems to crash, I don't think it's a carkit issue.
Anyone here with the same issue? And maybe a solution?
Thanks and regards!!
Start -> Settings -> Connections -> Bluetooth -> Timeout (tab). Turn off Visible mode set to "Never".
I think this must be your problem.
Hi Freco,
Thanks for your reply! This option is set. However it's not really the visibility that turns to invisible, but the whole bluetooth stack is being turned off completely. Need to fully re-enable it via Comm Manager.
Any other options? Does anyone know if there is a working broadcomm stack for the Touch Pro?
Regards!
Hi,
I have exactly the same problem with a Vauxhall kit, I have tried all sorts of things, but nothing seems to work
try:
start -> settings -> connections -> bluetooth
timeout tab
select 'never' from drop down box
Hi Brendo,
Unfortunately this doesn't solve the issue. Once paired, the connection even works without being visible. It's also not a fixed period of time before the disconnect takes place (can be within a minute, sometimes after half an hour). However, the whole bluetooth icons disappears from the top icon bar and comm manager shows it's turned off completely.
Hope somebody has any other ideas, because the only thing HTC can do is point to the carkit vendor :-(. Since all functionality is there when connected and the phone is turning off BT in some way, I really don't think this is caused by the carkit vendor. I should at least expect BT to stay enabled on the phone.
Thanks!
Yes, same here, BTW I have tried this in my Friends Saab, and the same problem.
same problem here with a Opel DVD90 buildin bluetooth carkit.
With other htc phones it always worked like a charm, but my mda vario IV continuously disconnects after a random time period and shuts down the complete stack.
Try this!
I have the same problem with my opel with original bluetooth-kit (2007). On the touch pro I changed the band and network from auto to GSM, as G3 reseption in this area is quit poor, especialy while driving. It helped for me, at least the last few days. I agree this has been an annoying problem.
I have tried to switch to "GSM only mode" in the past, but as far as I remember it does not completely solve the issue. However, I will give it another shot! Actually I can't figure out at what point it occurs... It can happen within a minute or after half an hour without using any funtion.
Does one of you know if there is a way to do some debugging on the Bluetooth stack?
And has anyone experience with other Windows Mobile 6.1 based phones in this combination (just curious if it's a WM issue or HTC only)?
Furthermore I did some tests with JetWare. You should be able to limit the number of synchronised items then (might be related to this issue). However, it looks like this configured limit is being totally ignored: when I limit my recent call list to 5 with JetWare, it still syncs about 25 items. Anyone tested with Jetware?
I have tried the GSM only mode, this didn't help either
I have now given up and got myself a Nokia E66, which works perfectly.
All contacts are pushed to car, no disconnects and AD2P works so my mp3 ringtones play through the car speakers! Sweet
Word of note, I had issues with N-Series phones, would connect ok, but contacts would not push.
I have the samen problem with my HTC Touch Pro and Saab.
bluetooth pairs just fine with my pioneer bluetooth enabled deck, but the problem iwth mine is once i receive a call sometimes no sound comes from the car, instead the earpiece is still on. but if i initiate the call first sound works just fine and earpiece on the phone is disabled, BUT once the call is ended bluetooth disconnects randomly and the phone takes a good 1-2min to reconnect. i absolutely hate the bluetooth on this phone!
ExTREmE99 said:
bluetooth pairs just fine with my pioneer bluetooth enabled deck, but the problem iwth mine is once i receive a call sometimes no sound comes from the car, instead the earpiece is still on. but if i initiate the call first sound works just fine and earpiece on the phone is disabled, BUT once the call is ended bluetooth disconnects randomly and the phone takes a good 1-2min to reconnect. i absolutely hate the bluetooth on this phone!
Click to expand...
Click to collapse
I am having the same problems you describe. Anyone got an suggestions???
I encountered the same problem; first with an opel udp carkit and next with the bluetooth interface software from homeseer.
It has something to do with phone signal loss.
With the opel carkit I noticed bluetooth automatically turns off when the phonesignal switched from 3g to gsm.
I also noticed that in my home, BT turns off whenever I have been in a room with no phone-signal reception.
try this thread, both registry change and attached cab file, reset. DOn't worry if the make visible to all option is unchecked.
http://forum.xda-developers.com/archive/index.php/t-314996.html