I am running Magneto on my Himalaya, and I want to get the Imate JasJar extended rom on my device. Can this be done?
I am certian that the extended rom for Magneto is not the same as that of the JasJar, but I do not know if it is compatable, and I can't find the ext rom anywhere.
Please help,
-cjj
Related
I bought a I-MATE JAQ4 from a software developer about 8 months ago. I guess this model never went into production, and the phone is a prototype. I-MATE quit the JAQ line. Oh well.
Anyway, anybody know what alternative OS builds I can install on this thing? I am guessing it is not too much different than the JAQ3, it just has WM6 on it.
Any insightful information about this device would be appreciated.
Thanks.
*bump*.....
Imate Jaq4
I also have a the Imate JAQ4 (which is a prototype) - I have been in touch with Imate (via their site) apparently the model is due for release anytime now in this country.
Try checking out the site for suitable downloads.
The only problem I have now encountered is finding a replacement battery - I had to do a hard reset on my unit and since then the battery wont charge (unless any one out there knows a way to jump start the battery back to life).
Everywhere I have tried that advertise compatable batteries do not seem to carry any stock.
I am not sure what is going on with the I-Mate JAQ4, however...
Isn't the same as the Pharos Traveler M619 (http://www.pharosgps.com/products/proddetail.asp?prod=001%5FPTL619%5F7%2E9&cat=136 )? I got one, pretty good, but slow processor and low memory (very similar to the Dash, at least it seems to me, but with bigger screen, touch screen and gps, )
There currently not much support in the way of firmware upgrades, but they did release version 6.1 a while back.
GPS refuse SD CARD ,WHY?
my configuration: 2G MICRO SD WITH ADAPTER
when i launch GPS , sd disappear and can't be accessed. i have to plug out and insert again.
why?
there is some patch for this bug .
thanks
just turn on my Axim bootloader mode if the switch connected to cable, but without making the battery, this happened after trying to upgrade to the WM5 ROM A01 and A05 had wm2k3 Please help me or if anyone knows how to recover using the JTAG and what are their points.
axim x50 low QVGA
intel xcale 450mhz
juanseti said:
just turn on my Axim bootloader mode if the switch connected to cable, but without making the battery, this happened after trying to upgrade to the WM5 ROM A01 and A05 had wm2k3 Please help me or if anyone knows how to recover using the JTAG and what are their points.
axim x50 low QVGA
intel xcale 450mhz
Click to expand...
Click to collapse
Welcome to the forum
Not sure if your device is made by HTC, as this is an HTC devices only forum
However perhaps another member can point you into the right direction
Good luck,
For the ignorant (or just plain don't know), the axim (both X50 series and X51 series) were both made by HTC under the codename HTC Colorado. Anyway, you were trying to upgrade from WM2003 SE A05 rom to the WM5 A01 rom and you bricked your axim, right?
whether it is right from WM2003 A05 to WM5 A01 rom was that my Axim is dead. I apologize for the delay but is walking without internet
Hi
I have problems with charging my x7510 after i have installed Xtep's Wm6.5. It wont charge very much and i looses power in 6 hours....
Does anyone have a soulution to my problem?
I am thinking of bying a new battery to the device, but it is only 1 year old...
Regards
HTC 7510 wm 6.5 inquiry
any idea about how does it work
is it better and worth upgrading to wm 6.5
thanks for reply in advance
I hav recently succeeded in upgrading my dopod 818 pro to wm6.1 rom (prophet shadow 2.0 TE) but after the upgrade i hav seen tht my dopod takes a much longer time to load now then before. And sometimes when im using the phone the phone speaker fails to function. I notice this mostly when i get a call nd i dont hear my phone ringing although i keep all volumes full. Please advice me on how to get a performance advantage after the upgrade nd advice me on how to solve the volume issue.
Thanks in advance
Hi all
I have an Orgrane branded SPV M3100 running Windows Mobile 6 with Schaps Rom 4.30
The question is, Is it possible to have the screen come alive when plugged into the mains to charge up or when sat in a car cradle?
I've had had a look at the power settings can't see any settings for this.
I was wondering is there something in the registry maybe?
Thanks
John
UK