Recently i bought poco x5 pro 5G and I'm having a issue where my phone keeps switching back to 4G most of the time probably due to low signals of 5G (-107 dBm 33 asu) so is there any way to stop my phone or have any control over my settings to not shift my connection from 5G to 4G.
So far low singal is the only way i could think of why my device is stuck on 4G whereas other phone in my house stay on 5G even with bad connection
My 4G (-82 dBm 58asu) vs 5G (-107 dBm 33 asu)
So far i tried setting connection on 5G preferred.
Any help or information would be great
You can try this code in dialer *#*#4636#*#* then change preffered network type to NR only.
Related
Hello,
I have been seeing horrible quality of network service in my area on Ting. I have a white 32GB Nexus 5. I work in a three story building that seems to turn my phone into Digital roaming/CDMA 1xRTT network only going outside I barely get 3G. I have mapped it out and see more service in the area where people on Sprint are getting 4G LTE in the area or WIMAX. I was wondering if anyone on Ting/Sprint has the same issue.
I do see 3G on my commute and downtown Sacramento, California where I should see 4G LTE I am barely getting 3G 2 to 3 bars. Most of my day at work in Folsom, California area is all 1xRTT 2G or Roaming when inside my office, and lower end 3G outside. I have two 3G/WIMAX towers next to my area at work in Folsom and I should be getting some 3G.
I went through the cell network code to enable band 26, and band 41 and changed priorities on the band from 1 to 0 and individually tested each band in my area. band 41 seems to be the best and the others are pretty bad. Band 41 gets me -100 dBm, 99asu, 950ms ping on CDMA 1xRTT.
I now have it back to all priority 1 (Bands: 25/26/41) Band 26 and 41 enabled. I have updated my Profile and PRL multiple times.
I am running 4.4.2 with Xposed Framework version 1.5, with Franco kernel r33. I did see Franco kernel r34 and will probably flash the update ASAP to see if it works any better. I am not using any power save settings for cell network quality. I am also using a Spiegen slim-armor case and tried to see if it was interfering with signal strength, it wasn't.
So my question comes down to has anybody known a fix for getting solid 3G in an area where I should be seeing some LTE and atleast full strength 3G. I am barely seeing 2G most of the time. I am just crossing my finger it isn't an antenna issue with the phone itself.
Any help, tips, or tricks would be greatly appreciated!!!
adramalech707 said:
Hello,
I have been seeing horrible quality of network service in my area on Ting. I have a white 32GB Nexus 5. I work in a three story building that seems to turn my phone into Digital roaming/CDMA 1xRTT network only going outside I barely get 3G. I have mapped it out and see more service in the area where people on Sprint are getting 4G LTE in the area or WIMAX. I was wondering if anyone on Ting/Sprint has the same issue.
I do see 3G on my commute and downtown Sacramento, California where I should see 4G LTE I am barely getting 3G 2 to 3 bars. Most of my day at work in Folsom, California area is all 1xRTT 2G or Roaming when inside my office, and lower end 3G outside. I have two 3G/WIMAX towers next to my area at work in Folsom and I should be getting some 3G.
I went through the cell network code to enable band 26, and band 41 and changed priorities on the band from 1 to 0 and individually tested each band in my area. band 41 seems to be the best and the others are pretty bad. Band 41 gets me -100 dBm, 99asu, 950ms ping on CDMA 1xRTT.
I now have it back to all priority 1 (Bands: 25/26/41) Band 26 and 41 enabled. I have updated my Profile and PRL multiple times.
I am running 4.4.2 with Xposed Framework version 1.5, with Franco kernel r33. I did see Franco kernel r34 and will probably flash the update ASAP to see if it works any better. I am not using any power save settings for cell network quality. I am also using a Spiegen slim-armor case and tried to see if it was interfering with signal strength, it wasn't.
So my question comes down to has anybody known a fix for getting solid 3G in an area where I should be seeing some LTE and atleast full strength 3G. I am barely seeing 2G most of the time. I am just crossing my finger it isn't an antenna issue with the phone itself.
Any help, tips, or tricks would be greatly appreciated!!!
Click to expand...
Click to collapse
Go to about phone and check your Baseband version, if your modem driver is older you may want to upgrade it. Or if it is newer, potentially a downgrade has shown better performance as well. All depends.
Read this thread thoroughly and make sure you do a backup before doing anything and see if this helps.
http://forum.xda-developers.com/showthread.php?t=2514095
adramalech707 said:
Hello,
I have been seeing horrible quality of network service in my area on Ting. I have a white 32GB Nexus 5. I work in a three story building that seems to turn my phone into Digital roaming/CDMA 1xRTT network only going outside I barely get 3G. I have mapped it out and see more service in the area where people on Sprint are getting 4G LTE in the area or WIMAX. I was wondering if anyone on Ting/Sprint has the same issue.
I do see 3G on my commute and downtown Sacramento, California where I should see 4G LTE I am barely getting 3G 2 to 3 bars. Most of my day at work in Folsom, California area is all 1xRTT 2G or Roaming when inside my office, and lower end 3G outside. I have two 3G/WIMAX towers next to my area at work in Folsom and I should be getting some 3G.
I went through the cell network code to enable band 26, and band 41 and changed priorities on the band from 1 to 0 and individually tested each band in my area. band 41 seems to be the best and the others are pretty bad. Band 41 gets me -100 dBm, 99asu, 950ms ping on CDMA 1xRTT.
I now have it back to all priority 1 (Bands: 25/26/41) Band 26 and 41 enabled. I have updated my Profile and PRL multiple times.
I am running 4.4.2 with Xposed Framework version 1.5, with Franco kernel r33. I did see Franco kernel r34 and will probably flash the update ASAP to see if it works any better. I am not using any power save settings for cell network quality. I am also using a Spiegen slim-armor case and tried to see if it was interfering with signal strength, it wasn't.
So my question comes down to has anybody known a fix for getting solid 3G in an area where I should be seeing some LTE and atleast full strength 3G. I am barely seeing 2G most of the time. I am just crossing my finger it isn't an antenna issue with the phone itself.
Any help, tips, or tricks would be greatly appreciated!!!
Click to expand...
Click to collapse
Look for the modem thread (didn't see you post it so if you did, sorry), and try flashing the .15 radio. That seems to be the best. The stock 4.4.2 radio (.21 or .23 can't remember) sucks. I could be halfway between towers and drop to 3g and not get LTE at all. The .15 holds LTE as long as there is really an LTE signal just fine.
i just read that ting uses sprints network. that might be the issue there, as sprint isnt known to have great coverage nor great data speeds.
adramalech707 said:
Hello,
!
Click to expand...
Click to collapse
Sacramento is entirely legacy lucent equipment. Basically **** sucks and won't get better anytime soon till they cluster launch the area. They won't fire up anything (3g / 800 mhz / 4G LTE) until they cluster launch. They can't cluster launch the area until all 200 or so sites are fully upgraded which is a ways off.
B41 is running of old Clearwire sites for now and should be mostly done by around may but you cannot connect to them unless you force LTE only mode and do the PRL update work around (i.e. PRL update every time you reboot the radio) and even then it leaves much to be desired.
So your option is to stick it out on the ****ty legacy network or find another provider that suits your needs. ATT is running 5 mhz on LTE 700 B, Tmobile has a 10x10 FDD-LTE network on AWS that is spotty as **** in around south sac area and drops to Edge when you go indoors which is probably a no go for you.
Probably the best option for you is an ATT MVNO considering your needs are inside a building.
-- Though if you do stick it out Sprint has quite an amazing portfolio in the Sacramento area with full access to eSMR 800 (5x5 mhz FDD-LTE band 26) + eSMR 800 1xAdvance, 20 mhz of PCS A-F + the 10mhz of PCS G (5x5mhz FDD-LTE Band 25) along with 55mhz of BRS (2500) + innumerable EBS (2600). Right now they're running B41 on EARFCN 40978 which is about 2630mhz or smack dab in the EBS block.
Tmobiles is here at 40mhz of AWS and ~30 mhz of PCS + the 700A later this year. They run 10x10 for FDD-LTE Band 4 and DC-HSPA+ on the other 20 mhz of AWS. They run a single PCS 5 mhz WCDMA 3G carrier and the rest of the PCS is GSM. Their 700A Band 12 will be limited to about 3x3mhz FDD-LTE when they deploy later.
ATT has quite a mishmash of spectrum. 12 mhz of 700B Band 17 (5x5 mhz FDD-LTE), 700D block Band 29 which is unpaired and unusable, the Cell 850 A block, 10mhz of AWS good for 5x5 FDD-LTE on Band 4, and 20 mhz of PCS A + D which is split for numerous WCDMA 3G + GSM carriers. So they're probably going to run AWS LTE and aggregate it with their 700B block LTE and then moving onto refarming PCS carriers later. IE -a nightmare.
Take your poison.
I'm not in your area, but Ting has been swell for me in Minnesota. Sprint's coverage map shows NO LTE in the Twin Cities of Minneapolis & St. Paul, though it exists well to the west in rural MN. Imagine my surprise to get it at my home in Hopkins, at least 75 miles away from Sprint's nearest report of coverage. Phone service is unchanged from when I was a Sprint customer.
SomeTing wong
Sent from my Nexus 5
Yes som ting is wong
Firstly it looks like when you got your service you only provided them the ESN number which they can provide you 3G and 1X
however you need a sprint 4G lte sim to actually get LTE along with 3G and 1X ask ting about it.
Hello all,
i have a problem, in my area ther are two LTE 4g bands coverage- lte 3 and lte 40.
My phone always remains connected to lte 3 band because it has slightly good network strength, but i want to connect to lte band 40 because it has very high data speed. in my office it connects to band 40 but at my home it remains connected to band 3, i get 100kbps (band 3)speed instead of 5-7mbps (band 40).
So how can i make to connect my phone to band 40 and not band 3.
I am rooted have supersu, busybox, multirom, nethunter on cm 13.1.2
a3Co00 said:
Hello all,
i have a problem, in my area ther are two LTE 4g bands coverage- lte 3 and lte 40.
My phone always remains connected to lte 3 band because it has slightly good network strength, but i want to connect to lte band 40 because it has very high data speed. in my office it connects to band 40 but at my home it remains connected to band 3, i get 100kbps (band 3)speed instead of 5-7mbps (band 40).
So how can i make to connect my phone to band 40 and not band 3.
I am rooted have supersu, busybox, multirom, nethunter on cm 13.1.2
Click to expand...
Click to collapse
even i want to lock my phone to band 40 but there no way possible because jio speeds are too low on band 3
Not possible as a phone will always connect to a strongest signal available within your area....in your case (at home) band 40 is not the strongest so it will connect to band 3 instead while in office its the other way around...
Recently I've started to experience exponential increase in dropped signal/phone rebooting/radio cycling on/off. It looks like my home is at the edge of verizon's band 4 coverage. They must have switched on or changed tower config over the past couple months, as that's when it started.
Essentially, my pixel is trying to connect to band 4, which is around -105 to -115 dBm. As a result, signal drops frequently. It'll connect to band 13 sometimes, which is great at -85 to -95 dBm. The thing is, seems like band 4 has priority, as the phone constantly drops the more stable band 13 connection in search of band 4.
Speedtest shows no benefit to me the enduser, as I am getting around 100/18 connection on both band 4 and 13. It's gotten to the point where this would happen every couple minutes, making the phone unusable.
Staying on wifi solves the data issue, but that's not ideal. And I still see the radio cycling on/off trying to search for signal even on wifi, which means I could potentially lose calls and texts.
Any suggestions on how to temp disable band 4, or at least prioritize band 13 over it? Thanks!
Hello fellow-members,
I just ordered my Nord, get the Device tomorrow! But i have a couple questions about the 5G.
How's the Nord handeling the 5G frequency?
How's the speed you are getting compared to 4G/LTE?
Are there specific settings you have to enable in the Nord for 5G?
Thnx in advance!
(ps i know its provider depended, but i like to know a little bit average)
This does not answer your question - but figured you might be interested in the following:
I am in the UK with a 5G contract but living in a 4G area.
When I enable the Auto 2G/3G/4G/5G mode on the nord my download speeds drop by around 50% - from the same location - testing over mutiple days.
If I put it back to Auto 2G/3G/4G the download speed increases again to normal higher speed.
In Auto 2G/3G/4G/5G I frequently see 'not connected to internet' messages when out and about in my locality - switching back to Auto 2G/3G/4G seems to resolve the issue.
I have not travelled to a 5G area to see what happens.
Thnx for your reply! After a vew days with the OP Nord in my hands i successfully can use 5G only speeds are a bit higher than 4G+, and sometimes lower. But all good here now
I'm on T-Mobile and I've noticed my phone alternating between 5G and LTE at random intervals. Both 5G and LTE are at 4 bars and I'm stationary. It's not really an issue because I didn't get this phone for 5G and the connection isn't dropping when it switches. Is anyone else experiencing this?
wvufankevin1991 said:
I'm on T-Mobile and I've noticed my phone alternating between 5G and LTE at random intervals. Both 5G and LTE are at 4 bars and I'm stationary. It's not really an issue because I didn't get this phone for 5G and the connection isn't dropping when it switches. Is anyone else experiencing this?
Click to expand...
Click to collapse
Actually mine has shown 5g constantly since I got it. Even though it's not using 5g. Mine is fully converted to TMobile
Mine is doing the same..... it must depend on signal strength or something. What concerns me about it is that 5g and 5g mwav is suppose to have less issues with walls, so why are the phones not staying on 5g? something is causing the 5g signal to go in and out.... I noticed less of an issue outside than inside which would be normal I guess, but should not be an issue for Tmobile's 5g service.
I live in NYC and don't have this issue with my phone. Could it be a problem with your location/city?
Have you called t-mobile about it yet?
Maybe do a speed test when it switches to see if you get lower speeds on LTE, maybe that would show if it is really actually switching or just an icon issue as both have the same amount of bars.
How are y'all determining that you are actually connected to a 5G carrier ? For AT&T, they have put the 5G icon on the man screen for awhile so I was looking at the Mobile data network setting under SIM card status but have only seen LTE. Having said that, I have done speed test where I am getting 20ms latency and 60Mbps download speeds.
Here is where the old Nokia Field Test Mode would be useful.
petraviva said:
How are y'all determining that you are actually connected to a 5G carrier ? For AT&T, they have put the 5G icon on the man screen for awhile so I was looking at the Mobile data network setting under SIM card status but have only seen LTE. Having said that, I have done speed test where I am getting 20ms latency and 60Mbps download speeds.
Here is where the old Nokia Field Test Mode would be useful.
Click to expand...
Click to collapse
Because, up were you have the bars that show how strong your signal is, it actually tells me when I am on 4G, 4G LTE or 5G, and at least one Tmob, do don't need a 5G enabled SIM, it should "Just work" if you have 5G service in your area and you are within range of a 5G equipt tower..... I also checked with apps like Open Signal and others to see what towers I am connecting to, etc.
5G download and upload speeds are crappy though....lol..... Should be broadband speeds and it is no were near that...