ok so just a question, because i think i understand what's happening
my phone will switch between umts, hspa and hspa+ a lot
it seems like whenever the phone is idle it sits on hspa. but when i do something requiring data(open up facebook, for example) it will switch to umts and then switch to hspa+
is that just because when switching from hspa to hspa+ it falls back onto umts before switching over to hspa+(which youre probably always on underneath the hspa(+) connection)?
I was at Disneyland today and I noticed that most of the time while inside the park it would only connect to HSPAP, and with the amount of people there, the speeds are usually abysmal, however if I go into the secret menu and choose "LTE only", it will connect to it and the speed and signal are perfectly fine.
After I connect to LTE via enabling LTE only, if I switch it back to LTE/GSM auto, it will stay on LTE for a while before dropping back down to HSPAP and not connecting to LTE unless I move out of the area or force it to connect.
This had never happened with my Nexus 4 when I enabled LTE on it. I've noticed that the Nexus 5 tends to switch to HSPAP more often than the Nexus 4 did (granted the radio was not intended for LTE on the nexus 4)
Does this have to do with the phone or my carrier (T-Mobile)?
Hello,
I have been seeing horrible quality of network service in my area on Ting. I have a white 32GB Nexus 5. I work in a three story building that seems to turn my phone into Digital roaming/CDMA 1xRTT network only going outside I barely get 3G. I have mapped it out and see more service in the area where people on Sprint are getting 4G LTE in the area or WIMAX. I was wondering if anyone on Ting/Sprint has the same issue.
I do see 3G on my commute and downtown Sacramento, California where I should see 4G LTE I am barely getting 3G 2 to 3 bars. Most of my day at work in Folsom, California area is all 1xRTT 2G or Roaming when inside my office, and lower end 3G outside. I have two 3G/WIMAX towers next to my area at work in Folsom and I should be getting some 3G.
I went through the cell network code to enable band 26, and band 41 and changed priorities on the band from 1 to 0 and individually tested each band in my area. band 41 seems to be the best and the others are pretty bad. Band 41 gets me -100 dBm, 99asu, 950ms ping on CDMA 1xRTT.
I now have it back to all priority 1 (Bands: 25/26/41) Band 26 and 41 enabled. I have updated my Profile and PRL multiple times.
I am running 4.4.2 with Xposed Framework version 1.5, with Franco kernel r33. I did see Franco kernel r34 and will probably flash the update ASAP to see if it works any better. I am not using any power save settings for cell network quality. I am also using a Spiegen slim-armor case and tried to see if it was interfering with signal strength, it wasn't.
So my question comes down to has anybody known a fix for getting solid 3G in an area where I should be seeing some LTE and atleast full strength 3G. I am barely seeing 2G most of the time. I am just crossing my finger it isn't an antenna issue with the phone itself.
Any help, tips, or tricks would be greatly appreciated!!!
adramalech707 said:
Hello,
I have been seeing horrible quality of network service in my area on Ting. I have a white 32GB Nexus 5. I work in a three story building that seems to turn my phone into Digital roaming/CDMA 1xRTT network only going outside I barely get 3G. I have mapped it out and see more service in the area where people on Sprint are getting 4G LTE in the area or WIMAX. I was wondering if anyone on Ting/Sprint has the same issue.
I do see 3G on my commute and downtown Sacramento, California where I should see 4G LTE I am barely getting 3G 2 to 3 bars. Most of my day at work in Folsom, California area is all 1xRTT 2G or Roaming when inside my office, and lower end 3G outside. I have two 3G/WIMAX towers next to my area at work in Folsom and I should be getting some 3G.
I went through the cell network code to enable band 26, and band 41 and changed priorities on the band from 1 to 0 and individually tested each band in my area. band 41 seems to be the best and the others are pretty bad. Band 41 gets me -100 dBm, 99asu, 950ms ping on CDMA 1xRTT.
I now have it back to all priority 1 (Bands: 25/26/41) Band 26 and 41 enabled. I have updated my Profile and PRL multiple times.
I am running 4.4.2 with Xposed Framework version 1.5, with Franco kernel r33. I did see Franco kernel r34 and will probably flash the update ASAP to see if it works any better. I am not using any power save settings for cell network quality. I am also using a Spiegen slim-armor case and tried to see if it was interfering with signal strength, it wasn't.
So my question comes down to has anybody known a fix for getting solid 3G in an area where I should be seeing some LTE and atleast full strength 3G. I am barely seeing 2G most of the time. I am just crossing my finger it isn't an antenna issue with the phone itself.
Any help, tips, or tricks would be greatly appreciated!!!
Click to expand...
Click to collapse
Go to about phone and check your Baseband version, if your modem driver is older you may want to upgrade it. Or if it is newer, potentially a downgrade has shown better performance as well. All depends.
Read this thread thoroughly and make sure you do a backup before doing anything and see if this helps.
http://forum.xda-developers.com/showthread.php?t=2514095
adramalech707 said:
Hello,
I have been seeing horrible quality of network service in my area on Ting. I have a white 32GB Nexus 5. I work in a three story building that seems to turn my phone into Digital roaming/CDMA 1xRTT network only going outside I barely get 3G. I have mapped it out and see more service in the area where people on Sprint are getting 4G LTE in the area or WIMAX. I was wondering if anyone on Ting/Sprint has the same issue.
I do see 3G on my commute and downtown Sacramento, California where I should see 4G LTE I am barely getting 3G 2 to 3 bars. Most of my day at work in Folsom, California area is all 1xRTT 2G or Roaming when inside my office, and lower end 3G outside. I have two 3G/WIMAX towers next to my area at work in Folsom and I should be getting some 3G.
I went through the cell network code to enable band 26, and band 41 and changed priorities on the band from 1 to 0 and individually tested each band in my area. band 41 seems to be the best and the others are pretty bad. Band 41 gets me -100 dBm, 99asu, 950ms ping on CDMA 1xRTT.
I now have it back to all priority 1 (Bands: 25/26/41) Band 26 and 41 enabled. I have updated my Profile and PRL multiple times.
I am running 4.4.2 with Xposed Framework version 1.5, with Franco kernel r33. I did see Franco kernel r34 and will probably flash the update ASAP to see if it works any better. I am not using any power save settings for cell network quality. I am also using a Spiegen slim-armor case and tried to see if it was interfering with signal strength, it wasn't.
So my question comes down to has anybody known a fix for getting solid 3G in an area where I should be seeing some LTE and atleast full strength 3G. I am barely seeing 2G most of the time. I am just crossing my finger it isn't an antenna issue with the phone itself.
Any help, tips, or tricks would be greatly appreciated!!!
Click to expand...
Click to collapse
Look for the modem thread (didn't see you post it so if you did, sorry), and try flashing the .15 radio. That seems to be the best. The stock 4.4.2 radio (.21 or .23 can't remember) sucks. I could be halfway between towers and drop to 3g and not get LTE at all. The .15 holds LTE as long as there is really an LTE signal just fine.
i just read that ting uses sprints network. that might be the issue there, as sprint isnt known to have great coverage nor great data speeds.
adramalech707 said:
Hello,
!
Click to expand...
Click to collapse
Sacramento is entirely legacy lucent equipment. Basically **** sucks and won't get better anytime soon till they cluster launch the area. They won't fire up anything (3g / 800 mhz / 4G LTE) until they cluster launch. They can't cluster launch the area until all 200 or so sites are fully upgraded which is a ways off.
B41 is running of old Clearwire sites for now and should be mostly done by around may but you cannot connect to them unless you force LTE only mode and do the PRL update work around (i.e. PRL update every time you reboot the radio) and even then it leaves much to be desired.
So your option is to stick it out on the ****ty legacy network or find another provider that suits your needs. ATT is running 5 mhz on LTE 700 B, Tmobile has a 10x10 FDD-LTE network on AWS that is spotty as **** in around south sac area and drops to Edge when you go indoors which is probably a no go for you.
Probably the best option for you is an ATT MVNO considering your needs are inside a building.
-- Though if you do stick it out Sprint has quite an amazing portfolio in the Sacramento area with full access to eSMR 800 (5x5 mhz FDD-LTE band 26) + eSMR 800 1xAdvance, 20 mhz of PCS A-F + the 10mhz of PCS G (5x5mhz FDD-LTE Band 25) along with 55mhz of BRS (2500) + innumerable EBS (2600). Right now they're running B41 on EARFCN 40978 which is about 2630mhz or smack dab in the EBS block.
Tmobiles is here at 40mhz of AWS and ~30 mhz of PCS + the 700A later this year. They run 10x10 for FDD-LTE Band 4 and DC-HSPA+ on the other 20 mhz of AWS. They run a single PCS 5 mhz WCDMA 3G carrier and the rest of the PCS is GSM. Their 700A Band 12 will be limited to about 3x3mhz FDD-LTE when they deploy later.
ATT has quite a mishmash of spectrum. 12 mhz of 700B Band 17 (5x5 mhz FDD-LTE), 700D block Band 29 which is unpaired and unusable, the Cell 850 A block, 10mhz of AWS good for 5x5 FDD-LTE on Band 4, and 20 mhz of PCS A + D which is split for numerous WCDMA 3G + GSM carriers. So they're probably going to run AWS LTE and aggregate it with their 700B block LTE and then moving onto refarming PCS carriers later. IE -a nightmare.
Take your poison.
I'm not in your area, but Ting has been swell for me in Minnesota. Sprint's coverage map shows NO LTE in the Twin Cities of Minneapolis & St. Paul, though it exists well to the west in rural MN. Imagine my surprise to get it at my home in Hopkins, at least 75 miles away from Sprint's nearest report of coverage. Phone service is unchanged from when I was a Sprint customer.
SomeTing wong
Sent from my Nexus 5
Yes som ting is wong
Firstly it looks like when you got your service you only provided them the ESN number which they can provide you 3G and 1X
however you need a sprint 4G lte sim to actually get LTE along with 3G and 1X ask ting about it.
I notice on my Nexus 6P, it tends to connect to band 12 quite often. At home where I have 3 bars of band 4, -122 dBm, restarting the radio will force the 6P to connect to band 12. I can't replicate this on the Note 5. I actually haven't seen band 12 on my Note 5 before.
Do you have this issue in band 12 areas? The baseband is COKC.
tengtengvn said:
I notice on my Nexus 6P, it tends to connect to band 12 quite often. At home where I have 3 bars of band 4, -122 dBm, restarting the radio will force the 6P to connect to band 12. I can't replicate this on the Note 5. I actually haven't seen band 12 on my Note 5 before.
Do you have this issue in band 12 areas? The baseband is COKC.
Click to expand...
Click to collapse
I tend to also check my Note 5's Service Mode now and then. It appears the phone prefers Band 4 over 12, which makes sense because Band 4 has much higher bandwidth than Band 12. There have more been instances lately where I will have Carrier Aggregation showing Band 4 and 12 together. The only time the phone will primarily use Band 12 is if I'm deep in a building and Band 4's signal is too low.
If you use #*2263# in the dialer, you can tweak these settings. You can force Band 12 if you want to for testing.
Here is a thread on this topic:
Okay. I have had my new Z3 for a while now and I love everything about the phone, accept for the reception quality. I am on AT&T and I travel in the same area routinly and I always had great reception in my normal travel area with my old Xperia V. At my home I always had 4 to 5 bars of signal. My new Z3 never gets more then 1 bar, if any. I almost never had dropped calls on my V no matter where I went. My Z3 drops calls all the time. My mom lives 150 miles away and I go to visit her at least twice a month. Many times I have driven the entire way while talking on my phone (with my BT headset) and never had a dropped call. I have been to her house several times since I got this Z3 and I have no signal about 80% of the time. I could not make a call if my life depended on it. At first I thought that the problem was that my V was using 3G towers and my new Z3 is using 4G towers. But I swtiched my Z3 to 3G only and it still has not signal in areas where my V used to have 4 to 5 bars.
As far as specs go, the Z3 (D6603) has all the same bands that the V has and more. The Z3 works on all the following 3G and 4G bands.
3G Network HSDPA 850 / 900 / 1700 / 1900 / 2100
4G Network LTE band 1(2100), 2(1900), 3(1800), 4(1700/2100), 5(850), 7(2600), 8(900), 13(700), 17(700), 20(800)
These are the bands the Xperia V operates on:
3G bands HSDPA 850 / 900 / 2100
4G bands LTE band 1(2100), 3(1800), 5(850), 7(2600), 20(800)
So what is the problem here? Why is the reception so bad on the Z3?
I'm having the same problem on my Z3. Few months back i used to get full range in my room or college classroom but now suddenly I hardly even get 1 bar. Hand to struggle to find reception. I think our antenna is at fault.