Hi everyone.
My Galaxy Tab 2 10.1 was running on LineageOS 13 but it was very slow. I wanted to go back to official rom.
I used Odin 3.14.4 and flashed P5100XXDMD1_P5100DBTDMD1_P5100XXDLL2_HOME.tar.
Everything seemed fine (see log below) exept it doesn't boot!
It loops on the blue circle turning into the Samsung logo.
Re-flashing did not help.
The log:
Code:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Added!!
<ID:0/005> Odin engine v(ID:3.1401)..
<ID:0/005> File analysis..
<ID:0/005> Total Binary size: 1126 M
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> NAND Write Start!!
<ID:0/005> SingleDownload.
<ID:0/005> system.img
<ID:0/005> boot.img
<ID:0/005> cache.img
<ID:0/005> hidden.img
<ID:0/005> recovery.img
<ID:0/005> modem.bin
<ID:0/005> MLO
<ID:0/005> param.lfs
<ID:0/005> Sbl.bin
<ID:0/005> RQT_CLOSE !!
<ID:0/005> RES OK !!
<ID:0/005> Removed!!
<ID:0/005> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
wasThere said:
Hi everyone.
My Galaxy Tab 2 10.1 was running on LineageOS 13 but it was very slow. I wanted to go back to official rom.
I used Odin 3.14.4 and flashed P5100XXDMD1_P5100DBTDMD1_P5100XXDLL2_HOME.tar.
Everything seemed fine (see log below) exept it doesn't boot!
It loops on the blue circle turning into the Samsung logo.
Re-flashing did not help.
The log:
Code:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Added!!
<ID:0/005> Odin engine v(ID:3.1401)..
<ID:0/005> File analysis..
<ID:0/005> Total Binary size: 1126 M
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> NAND Write Start!!
<ID:0/005> SingleDownload.
<ID:0/005> system.img
<ID:0/005> boot.img
<ID:0/005> cache.img
<ID:0/005> hidden.img
<ID:0/005> recovery.img
<ID:0/005> modem.bin
<ID:0/005> MLO
<ID:0/005> param.lfs
<ID:0/005> Sbl.bin
<ID:0/005> RQT_CLOSE !!
<ID:0/005> RES OK !!
<ID:0/005> Removed!!
<ID:0/005> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
Click to expand...
Click to collapse
Force tab to recovery and do factory reset!
drnightshadow said:
Force tab to recovery and do factory reset!
Click to expand...
Click to collapse
I can't.
Power + volume up = reboot
Power + volume down = download mode
wasThere said:
I can't.
Power + volume up = reboot
Power + volume down = download mode
Click to expand...
Click to collapse
Try to redownload firmware... Something was wrong, if you can't access to recovery... Are you sure your downloading the right firmware for your tab?
And try using older odin... just an idea.
drnightshadow said:
And try using older odin... just an idea.
Click to expand...
Click to collapse
Good guess. Odin 3.09 worked better.
Now, power + volume up leads to recovery. I did the factory reset and then reboot.
It's fine.
Thank you very much (as I am too stupid to find the Thanks button!).
wasThere said:
Good guess. Odin 3.09 worked better.
Now, power + volume up leads to recovery. I did the factory reset and then reboot.
It's fine.
Thank you very much (as I am too stupid to find the Thanks button!).
Click to expand...
Click to collapse
Lol haha ... Thanks button he he .. I'm to lazy to update it
Anyway, it's nice to hear that you bring your tab back to life.
Try clicking like button instead of thanks
Related
I tried to flash CyanogenMod and i couldn't activate / stuck in roaming. So, i followed the steps outlined here -- in the fixing data section ( http://forum.xda-developers.com/showthread.php?t=2053799 ). I have tried new USB cables,ports,restarts -- But Odin wont flash the system... It got far enough to flash the recovery away so I don't have CWM installed anymore... This is really starting to piss me off... Please help
I have searched everywhere but all i can find is people telling me to change my USB cable... I wish it was that simple.
Thanks,
Elliott
have you tried using another version of odin like 1.8.5
Blackwolf10 said:
have you tried using another version of odin like 1.8.5
Click to expand...
Click to collapse
Yea, ive tried 3.07 and 1.85
This is what i get from Odin
<ID:0/005> Added!!
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> boot.img
<ID:0/005> NAND Write Start!!
<ID:0/005> recovery.img
<ID:0/005> system.img.ext4
<ID:0/005> __XmitData_Read ..
<ID:0/005> XmitData Fail..
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
elliott35 said:
Yea, ive tried 3.07 and 1.85
This is what i get from Odin
<ID:0/005> Added!!
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> boot.img
<ID:0/005> NAND Write Start!!
<ID:0/005> recovery.img
<ID:0/005> system.img.ext4
<ID:0/005> __XmitData_Read ..
<ID:0/005> XmitData Fail..
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
This looks promising http://forum.xda-developers.com/showthread.php?t=1840030
elliott35 said:
This looks promising http://forum.xda-developers.com/showthread.php?t=1840030
Click to expand...
Click to collapse
Mine was fixed when I didn't use VMware Fusion on a mac but a PC directly
hhahah just changed the cable and it worked woowww
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/042> Added!!
<ID:0/042> Odin engine v(ID:3.1207)..
<ID:0/042> File analysis..
<ID:0/042> SetupConnection..
<ID:0/042> Initialzation..
<ID:0/042> Get PIT for mapping..
<ID:0/042> Firmware update start..
<ID:0/042> NAND Write Start!!
<ID:0/042> SingleDownload.
<ID:0/042> sboot.bin
<ID:0/042> FAIL!
<ID:0/042>
<ID:0/042> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I found This Problem Plz Help Me...
Hello everyone.
sorry my English writing is not very well
I have a samsung galaxy gt-p3110 with a defect When I put the power button on he is starting and i'll see the samsung logo on the screen.
After a view seconds the tablet is getting off.
the power button + volume up does not work.
when i put the power button + volume button down it is going in the download modus.
When i open odin3 and plugged the USB cable in to my pc,the samsung connect with odin but i dont no what to do.
I dont no what rom was on the tablet before,
so who can help me
With compliments, Raymon
raymon nijenhuis said:
Hello everyone.
sorry my English writing is not very well
I have a samsung galaxy gt-p3110 with a defect When I put the power button on he is starting and i'll see the samsung logo on the screen.
After a view seconds the tablet is getting off.
the power button + volume up does not work.
when i put the power button + volume button down it is going in the download modus.
When i open odin3 and plugged the USB cable in to my pc,the samsung connect with odin but i dont no what to do.
I dont no what rom was on the tablet before,
so who can help me
With compliments, Raymon
Click to expand...
Click to collapse
Did you download the lastest firmware available for P-3110 on samfirmware?
If yes, when you connect your tablet to your PC, ODIN says something like "0:[COM4]" with a blue blackground?
If yes, put the .md5 file taken from lastest firmware downloaded before and add it into PDA..Then check the "Auto-Reboot" and "F.reset Time" boxes and click start! Wait 5 min and when a green background with a text "PASS!" appears, your Tab will reboot itself.
Hope this helps you )
Thank you
I gonna try it out.
I'm letting you know
:good:
Ive tried what you said but everything seems to be going good but after installing the rom the samsung is getting on and a few secs later (the samung logo is vissible)it's going of.
Odin saids
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> P3110XXDNE1_P3110PHNDNE1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> system.img
<ID:0/005> NAND Write Start!!
<ID:0/005> boot.img
<ID:0/005> cache.img
<ID:0/005> hidden.img
<ID:0/005> recovery.img
<ID:0/005> MLO
<ID:0/005> param.lfs
<ID:0/005> Sbl.bin
<ID:0/005> RQT_CLOSE !!
<ID:0/005> RES OK !!
<ID:0/005> Removed!!
power button + volume up nothing(only the samsung screen for a couple of secs)
What I'm doing wrong?
raymon nijenhuis said:
Ive tried what you said but everything seems to be going good but after installing the rom the samsung is getting on and a few secs later (the samung logo is vissible)it's going of.
Odin saids
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> P3110XXDNE1_P3110PHNDNE1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> system.img
<ID:0/005> NAND Write Start!!
<ID:0/005> boot.img
<ID:0/005> cache.img
<ID:0/005> hidden.img
<ID:0/005> recovery.img
<ID:0/005> MLO
<ID:0/005> param.lfs
<ID:0/005> Sbl.bin
<ID:0/005> RQT_CLOSE !!
<ID:0/005> RES OK !!
<ID:0/005> Removed!!
power button + volume up nothing(only the samsung screen for a couple of secs)
What I'm doing wrong?
Click to expand...
Click to collapse
Did you unplug the cable when there was a text box with a green background saying "PASS!"?
I think no, because there is no "PASS" in your log..So re-flash the ROM.
P.s. And then..After the RES OK text did the tab reboot itself?
Did you unplug the cable when there was a text box with a green background saying "PASS!"? yes
I think no, because there is no "PASS" in your log..So re-flash the ROM. OKE
After the RES OK text did the tab reboot itself?yes for a few seconds and then its of again
Shall i try another rom?I dont no what happens before with this tab.
Thanks for helping me
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> P3110XXDMH1_P3110OXADMH1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> boot.img
<ID:0/005> NAND Write Start!!
<ID:0/005> cache.img
<ID:0/005> hidden.img
<ID:0/005> recovery.img
<ID:0/005> system.img
<ID:0/005> Sbl.bin
<ID:0/005> RQT_CLOSE !!
<ID:0/005> RES OK !!
<ID:0/005> Removed!!
<ID:0/005> Completed..
<OSM> All threads completed. (succeed 1 / failed 0)
raymon nijenhuis said:
Did you unplug the cable when there was a text box with a green background saying "PASS!"? yes
I think no, because there is no "PASS" in your log..So re-flash the ROM. OKE
After the RES OK text did the tab reboot itself?yes for a few seconds and then its of again
Shall i try another rom?I dont no what happens before with this tab.
Thanks for helping me
Added!!
Enter CS for MD5..
Check MD5.. Do not unplug the cable..
Please wait..
P3110XXDMH1_P3110OXADMH1_HOME.tar.md5 is valid.
Checking MD5 finished Sucessfully..
Leave CS..
Odin v.3 engine (ID:5)..
File analysis..
SetupConnection..
Initialzation..
Get PIT for mapping..
Firmware update start..
boot.img
NAND Write Start!!
cache.img
hidden.img
recovery.img
system.img
Sbl.bin
RQT_CLOSE !!
RES OK !!
Removed!!
Completed..
All threads completed. (succeed 1 / failed 0)
Click to expand...
Click to collapse
Mmm..The log seems great for me.
I mean, it should works.
But what happened to this Tab? Why it went to bootloop?
P.s. Anyways, try another firmware.
SlimShady's said:
Mmm..The log seems great for me.
I mean, it should works.
But what happened to this Tab? Why it went to bootloop?
P.s. Anyways, try another firmware.
Click to expand...
Click to collapse
I dont know what happend to this tab,I bought this thing with the problem.
I tried other roms but everytime with the same result.
What does bootloader do?
what can I do :crying:
raymon nijenhuis said:
I dont know what happend to this tab,I bought this thing with the problem.
I tried other roms but everytime with the same result.
What does bootloader do?
what can I do :crying:
Click to expand...
Click to collapse
I think is a motherboard problem..With that successfully log, it MUST work..
raymon nijenhuis said:
Did you unplug the cable when there was a text box with a green background saying "PASS!"? yes
I think no, because there is no "PASS" in your log..So re-flash the ROM. OKE
After the RES OK text did the tab reboot itself?yes for a few seconds and then its of again
Shall i try another rom?I dont no what happens before with this tab.
Thanks for helping me
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> P3110XXDMH1_P3110OXADMH1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> boot.img
<ID:0/005> NAND Write Start!!
<ID:0/005> cache.img
<ID:0/005> hidden.img
<ID:0/005> recovery.img
<ID:0/005> system.img
<ID:0/005> Sbl.bin
<ID:0/005> RQT_CLOSE !!
<ID:0/005> RES OK !!
<ID:0/005> Removed!!
<ID:0/005> Completed..
<OSM> All threads completed. (succeed 1 / failed 0)
Click to expand...
Click to collapse
you try to press the power button and volume up to enter the system recovery after that you select menu factory reset so select.
after which your phone will reboot itself. and wait 5-10 minutes at the start of entry of boot logo.
if it still fails try to open the back cover of your phone and remove the battery let stand until 10-20 minutes.
and put again the battery in place.try to trun on your phone...
Hi,
I am having a lot of trouble flashing my Note 3 (SM-N9005) 16gb to Android 5.0. At this point in time, all I can do is enter into DL mode.
I have been trying to use Odin to flash my device, but I think I must have messed up the PIT file by accident - using a 32gb instead of a 16 gb. I now know that I should never have touched the PIT button.
I am using this stock firmware: N9005XXUEND4_N9005FTMEND1_N9005XXUENC2_HOME.tar.md5 to get back to old version.
Odin reads:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N9005XXUEND4_N9005FTMEND1_N9005XXUENC2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> aboot.mbn
<ID:0/005> NAND Write Start!!
<ID:0/005> sbl1.mbn
<ID:0/005> rpm.mbn
<ID:0/005> tz.mbn
<ID:0/005> sdi.mbn
<ID:0/005> NON-HLOS.bin
<ID:0/005> boot.img
<ID:0/005> recovery.img
<ID:0/005> system.img.ext4
<ID:0/005> FAIL! (Ext4)
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Is there someway to fix this?
Thanks in advance!
dmar16 said:
Hi,
I am having a lot of trouble flashing my Note 3 (SM-N9005) 16gb to Android 5.0. At this point in time, all I can do is enter into DL mode.
I have been trying to use Odin to flash my device, but I think I must have messed up the PIT file by accident - using a 32gb instead of a 16 gb. I now know that I should never have touched the PIT button.
I am using this stock firmware: N9005XXUEND4_N9005FTMEND1_N9005XXUENC2_HOME.tar.md5 to get back to old version.
Odin reads:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N9005XXUEND4_N9005FTMEND1_N9005XXUENC2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> aboot.mbn
<ID:0/005> NAND Write Start!!
<ID:0/005> sbl1.mbn
<ID:0/005> rpm.mbn
<ID:0/005> tz.mbn
<ID:0/005> sdi.mbn
<ID:0/005> NON-HLOS.bin
<ID:0/005> boot.img
<ID:0/005> recovery.img
<ID:0/005> system.img.ext4
<ID:0/005> FAIL! (Ext4)
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Is there someway to fix this?
Thanks in advance!
Click to expand...
Click to collapse
Use the right pit file and you should be fine.
LS.xD said:
Use the right pit file and you should be fine.
Click to expand...
Click to collapse
Thanks. I tried that with this PIT file [HLTE_HKTW_OPEN_16G.pit], but get this message now:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N9005XXUEND4_N9005FTMEND1_N9005XXUENC2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> aboot.mbn
<ID:0/005> NAND Write Start!!
<ID:0/005> sbl1.mbn
<ID:0/005> rpm.mbn
<ID:0/005> tz.mbn
<ID:0/005> sdi.mbn
<ID:0/005> NON-HLOS.bin
<ID:0/005> boot.img
<ID:0/005> recovery.img
<ID:0/005> system.img.ext4
<ID:0/005> FAIL! (Ext4)
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
My phone says:
"ODIN : Invalid ext4 image"
Is there a better PIT file I should use?
Try restarting odin, use right pit file and it should flash the stock rom
Don't forget to hit thanks if I helped you...
dmar16 said:
Thanks. I tried that with this PIT file [HLTE_HKTW_OPEN_16G.pit], but get this message now:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N9005XXUEND4_N9005FTMEND1_N9005XXUENC2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> aboot.mbn
<ID:0/005> NAND Write Start!!
<ID:0/005> sbl1.mbn
<ID:0/005> rpm.mbn
<ID:0/005> tz.mbn
<ID:0/005> sdi.mbn
<ID:0/005> NON-HLOS.bin
<ID:0/005> boot.img
<ID:0/005> recovery.img
<ID:0/005> system.img.ext4
<ID:0/005> FAIL! (Ext4)
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
My phone says:
"ODIN : Invalid ext4 image"
Is there a better PIT file I should use?
Click to expand...
Click to collapse
You phone (or at least the stock firmware you want to use is "France - Orange") There has no official Lollipop update been released yet.
The pit file is "Hong Kong -Taiwan" , may be its not compatible to each other. Try to get a pit file that matches your firmware. Or take a firmware that matches the pit file. In any case you should backup your EFS before going on flashing different firmwares. Use TWRP to backup your EFS .
OK thanks. Downloading FW for Hong Kong - Taiwan now. I will let you know if it works.
Hi everyone
I have a galaxy note tab 10.1 GT-N8013ZWYXAR (wifi only ) but it stuck on screne logo i try to fix with odin to install new frimwear its says all steps completed but agin stuck on logo screen . I try with odin to uncheck auto-rebot but same i have a same problem.
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin engine v(ID:3.1100)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> boot.img
<ID:0/005> NAND Write Start!!
<ID:0/005> recovery.img
<ID:0/005> system.img
<ID:0/005> cache.img
<ID:0/005> hidden.img
<ID:0/005> sboot.bin
<ID:0/005> param.bin
<ID:0/005> tz.img
<ID:0/005> RQT_CLOSE !!
<ID:0/005> RES OK !!
<ID:0/005> Removed!!
<ID:0/005> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0
Can someone help me to fix it ?
Thnx
Hello, i am having a problem flashing the stock rom on GT-i9105P, i tried alot of roms but still none of them works.
I tried 4 Files repair firmware 4.1.2 and this is the log:
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> BcmBoot.img
<ID:0/005> NAND Write Start!!
<ID:0/005> HEDGE_RF_LE_SS_CAPRI_00.bin
<ID:0/005> sysparm_dep.img
<ID:0/005> sysparm2_dep_blob.img
<ID:0/005> sboot.bin
<ID:0/005> param.lfs
<ID:0/005> dt-blob
<ID:0/005> vc-firmware.img
<ID:0/005> boot.img
<ID:0/005> recovery.img
<ID:0/005> system.img
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
---------------------------------------------------------------
4.1.2 Stock rom 1 file, flash log:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9105PXXAMC2_I9105POXXAMB5_I9105PXXAMC1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Added!!
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> sboot.bin
<ID:0/005> NAND Write Start!!
<ID:0/005> vc-firmware.img
<ID:0/005> boot.img
<ID:0/005> recovery.img
<ID:0/005> BcmCP.img
<ID:0/005> dt-blob
<ID:0/005> cache.img
<ID:0/005> system.img
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
-------------------------------------------------------
4.2.2 Stock rom 1 file, flash log:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9105PXXUBNB1_I9105POXABNA1_I9105PXXUBNB1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Added!!
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> sboot.bin
<ID:0/005> NAND Write Start!!
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I also trie alot of Odin versions, but none works :/
Help me please, i've been trying to flash it from 2 days ago
Have you tried flashing RedRom, made by me?
It's stock 4.2.2 + extra optimizations.
Johnny TDN said:
Have you tried flashing RedRom, made by me?
It's stock 4.2.2 + extra optimizations.
Click to expand...
Click to collapse
First, thanks for replying.
No, i didn't try it..i would like to ask if you can give me it!
Goat678 said:
First, thanks for replying.
No, i didn't try it..i would like to ask if you can give me it!
Click to expand...
Click to collapse
Check my threads on my.profile. You will find RedRom there.
Johnny TDN said:
Check my threads on my.profile. You will find RedRom there.
Click to expand...
Click to collapse
Well, thx i already found it..
But still having a problem in odin while flashing TWRP/CWM recoveries...
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> TWRP-2.6.30_4.2.2_ODIN-s2vep.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> recovery.img
<ID:0/003> NAND Write Start!!
<ID:0/003> Complete(Write) operation failed.
<ID:0/003> Added!!
Can you help me please?
Goat678 said:
Well, thx i already found it..
But still having a problem in odin while flashing TWRP/CWM recoveries...
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> TWRP-2.6.30_4.2.2_ODIN-s2vep.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> recovery.img
<ID:0/003> NAND Write Start!!
<ID:0/003> Complete(Write) operation failed.
<ID:0/003> Added!!
Can you help me please?
Click to expand...
Click to collapse
If you have root on your phone, use Flashify.
...
Johnny TDN said:
If you have root on your phone, use Flashify.
Click to expand...
Click to collapse
Well, the phone is not turning on.
While turning on shows this message "Firmware upgrade encountered an issue. Please select recovery mode in Kies & try again."
and i cannot boot to recovery mode on my device and cannot flash any thing :/
Goat678 said:
Well, the phone is not turning on.
While turning on shows this message "Firmware upgrade encountered an issue. Please select recovery mode in Kies & try again."
and i cannot boot to recovery mode on my device and cannot flash any thing :/
Click to expand...
Click to collapse
Try this one
https://m.youtube.com/watch?v=7zEhC4kvMUE
Goat678 said:
Well, the phone is not turning on.
While turning on shows this message "Firmware upgrade encountered an issue. Please select recovery mode in Kies & try again."
and i cannot boot to recovery mode on my device and cannot flash any thing :/
Click to expand...
Click to collapse
You fixed your problem?
Johnny TDN said:
You fixed your problem?
Click to expand...
Click to collapse
Unfortunately, no.
I still can't fix it
Goat678 said:
Unfortunately, no.
I still can't fix it
Click to expand...
Click to collapse
Then i'm afraid that you must buy a new motherboard. Sorry.
Johnny TDN said:
Then i'm afraid that you must buy a new motherboard. Sorry.
Click to expand...
Click to collapse
Well, i kept trying till i just flashed TWRP recovery, then installed your RedRom
and its very good!
Thanks ♥