Samsung Galaxy Tab GT-N8013 Stoc on Galaxy Tab logo - Galaxy Note 10.1 Q&A, Help & Troubleshooting

Hi everyone
I have a galaxy note tab 10.1 GT-N8013ZWYXAR (wifi only ) but it stuck on screne logo i try to fix with odin to install new frimwear its says all steps completed but agin stuck on logo screen . I try with odin to uncheck auto-rebot but same i have a same problem.
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin engine v(ID:3.1100)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> boot.img
<ID:0/005> NAND Write Start!!
<ID:0/005> recovery.img
<ID:0/005> system.img
<ID:0/005> cache.img
<ID:0/005> hidden.img
<ID:0/005> sboot.bin
<ID:0/005> param.bin
<ID:0/005> tz.img
<ID:0/005> RQT_CLOSE !!
<ID:0/005> RES OK !!
<ID:0/005> Removed!!
<ID:0/005> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0
Can someone help me to fix it ?
Thnx

Related

[Q] Trying to Manually update to 5.0 SM-N9005; Odin - Error: FAIL!(Ext4)

Hi,
I am having a lot of trouble flashing my Note 3 (SM-N9005) 16gb to Android 5.0. At this point in time, all I can do is enter into DL mode.
I have been trying to use Odin to flash my device, but I think I must have messed up the PIT file by accident - using a 32gb instead of a 16 gb. I now know that I should never have touched the PIT button.
I am using this stock firmware: N9005XXUEND4_N9005FTMEND1_N9005XXUENC2_HOME.tar.md5 to get back to old version.
Odin reads:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N9005XXUEND4_N9005FTMEND1_N9005XXUENC2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> aboot.mbn
<ID:0/005> NAND Write Start!!
<ID:0/005> sbl1.mbn
<ID:0/005> rpm.mbn
<ID:0/005> tz.mbn
<ID:0/005> sdi.mbn
<ID:0/005> NON-HLOS.bin
<ID:0/005> boot.img
<ID:0/005> recovery.img
<ID:0/005> system.img.ext4
<ID:0/005> FAIL! (Ext4)
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Is there someway to fix this?
Thanks in advance!
dmar16 said:
Hi,
I am having a lot of trouble flashing my Note 3 (SM-N9005) 16gb to Android 5.0. At this point in time, all I can do is enter into DL mode.
I have been trying to use Odin to flash my device, but I think I must have messed up the PIT file by accident - using a 32gb instead of a 16 gb. I now know that I should never have touched the PIT button.
I am using this stock firmware: N9005XXUEND4_N9005FTMEND1_N9005XXUENC2_HOME.tar.md5 to get back to old version.
Odin reads:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N9005XXUEND4_N9005FTMEND1_N9005XXUENC2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> aboot.mbn
<ID:0/005> NAND Write Start!!
<ID:0/005> sbl1.mbn
<ID:0/005> rpm.mbn
<ID:0/005> tz.mbn
<ID:0/005> sdi.mbn
<ID:0/005> NON-HLOS.bin
<ID:0/005> boot.img
<ID:0/005> recovery.img
<ID:0/005> system.img.ext4
<ID:0/005> FAIL! (Ext4)
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Is there someway to fix this?
Thanks in advance!
Click to expand...
Click to collapse
Use the right pit file and you should be fine.
LS.xD said:
Use the right pit file and you should be fine.
Click to expand...
Click to collapse
Thanks. I tried that with this PIT file [HLTE_HKTW_OPEN_16G.pit], but get this message now:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N9005XXUEND4_N9005FTMEND1_N9005XXUENC2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> aboot.mbn
<ID:0/005> NAND Write Start!!
<ID:0/005> sbl1.mbn
<ID:0/005> rpm.mbn
<ID:0/005> tz.mbn
<ID:0/005> sdi.mbn
<ID:0/005> NON-HLOS.bin
<ID:0/005> boot.img
<ID:0/005> recovery.img
<ID:0/005> system.img.ext4
<ID:0/005> FAIL! (Ext4)
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
My phone says:
"ODIN : Invalid ext4 image"
Is there a better PIT file I should use?
Try restarting odin, use right pit file and it should flash the stock rom
Don't forget to hit thanks if I helped you...
dmar16 said:
Thanks. I tried that with this PIT file [HLTE_HKTW_OPEN_16G.pit], but get this message now:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N9005XXUEND4_N9005FTMEND1_N9005XXUENC2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> aboot.mbn
<ID:0/005> NAND Write Start!!
<ID:0/005> sbl1.mbn
<ID:0/005> rpm.mbn
<ID:0/005> tz.mbn
<ID:0/005> sdi.mbn
<ID:0/005> NON-HLOS.bin
<ID:0/005> boot.img
<ID:0/005> recovery.img
<ID:0/005> system.img.ext4
<ID:0/005> FAIL! (Ext4)
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
My phone says:
"ODIN : Invalid ext4 image"
Is there a better PIT file I should use?
Click to expand...
Click to collapse
You phone (or at least the stock firmware you want to use is "France - Orange") There has no official Lollipop update been released yet.
The pit file is "Hong Kong -Taiwan" , may be its not compatible to each other. Try to get a pit file that matches your firmware. Or take a firmware that matches the pit file. In any case you should backup your EFS before going on flashing different firmwares. Use TWRP to backup your EFS .
OK thanks. Downloading FW for Hong Kong - Taiwan now. I will let you know if it works.

Note edge SM-N915P (Need help)

i am getting a message "firmware upgrade encountered an issue. please select recovery mode in kies and try again"
So I booted in download mode and tried to install the stock rom on odin and it fails
What am i doing wrong?
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N915PVPU2BOC8_N915PSPT2BOC8_N915PVPU2BOC8_HOME.tar .md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> aboot.mbn
<ID:0/005> NAND Write Start!!
<ID:0/005> sbl1.mbn
<ID:0/005> rpm.mbn
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<ID:0/005> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)

I can't flash anything to my Note 5

I'm trying to go back to stock and i've tried every which way. When I try to do it through Odin it fails. I've tried on every USB port I have.
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin engine v(ID:3.1100)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> sboot.bin
<ID:0/005> NAND Write Start!!
<ID:0/005> cm.bin
<ID:0/005> FAIL!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Then I tried through Smart Switch and it says its a Galaxy Edge 7 so it doesn't let me do the emergency restore.
Then I tried to flash any other room though TWRP and it just says failed and give Error 7.
Any help will be appreciated.

GT-i9105p can't flash stock rom

Hello, i am having a problem flashing the stock rom on GT-i9105P, i tried alot of roms but still none of them works.
I tried 4 Files repair firmware 4.1.2 and this is the log:
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> BcmBoot.img
<ID:0/005> NAND Write Start!!
<ID:0/005> HEDGE_RF_LE_SS_CAPRI_00.bin
<ID:0/005> sysparm_dep.img
<ID:0/005> sysparm2_dep_blob.img
<ID:0/005> sboot.bin
<ID:0/005> param.lfs
<ID:0/005> dt-blob
<ID:0/005> vc-firmware.img
<ID:0/005> boot.img
<ID:0/005> recovery.img
<ID:0/005> system.img
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
---------------------------------------------------------------
4.1.2 Stock rom 1 file, flash log:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9105PXXAMC2_I9105POXXAMB5_I9105PXXAMC1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Added!!
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> sboot.bin
<ID:0/005> NAND Write Start!!
<ID:0/005> vc-firmware.img
<ID:0/005> boot.img
<ID:0/005> recovery.img
<ID:0/005> BcmCP.img
<ID:0/005> dt-blob
<ID:0/005> cache.img
<ID:0/005> system.img
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
-------------------------------------------------------
4.2.2 Stock rom 1 file, flash log:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9105PXXUBNB1_I9105POXABNA1_I9105PXXUBNB1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Added!!
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> sboot.bin
<ID:0/005> NAND Write Start!!
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I also trie alot of Odin versions, but none works :/
Help me please, i've been trying to flash it from 2 days ago
Have you tried flashing RedRom, made by me?
It's stock 4.2.2 + extra optimizations.
Johnny TDN said:
Have you tried flashing RedRom, made by me?
It's stock 4.2.2 + extra optimizations.
Click to expand...
Click to collapse
First, thanks for replying.
No, i didn't try it..i would like to ask if you can give me it!
Goat678 said:
First, thanks for replying.
No, i didn't try it..i would like to ask if you can give me it!
Click to expand...
Click to collapse
Check my threads on my.profile. You will find RedRom there.
Johnny TDN said:
Check my threads on my.profile. You will find RedRom there.
Click to expand...
Click to collapse
Well, thx i already found it..
But still having a problem in odin while flashing TWRP/CWM recoveries...
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> TWRP-2.6.30_4.2.2_ODIN-s2vep.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> recovery.img
<ID:0/003> NAND Write Start!!
<ID:0/003> Complete(Write) operation failed.
<ID:0/003> Added!!
Can you help me please?
Goat678 said:
Well, thx i already found it..
But still having a problem in odin while flashing TWRP/CWM recoveries...
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> TWRP-2.6.30_4.2.2_ODIN-s2vep.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> recovery.img
<ID:0/003> NAND Write Start!!
<ID:0/003> Complete(Write) operation failed.
<ID:0/003> Added!!
Can you help me please?
Click to expand...
Click to collapse
If you have root on your phone, use Flashify.
...
Johnny TDN said:
If you have root on your phone, use Flashify.
Click to expand...
Click to collapse
Well, the phone is not turning on.
While turning on shows this message "Firmware upgrade encountered an issue. Please select recovery mode in Kies & try again."
and i cannot boot to recovery mode on my device and cannot flash any thing :/
Goat678 said:
Well, the phone is not turning on.
While turning on shows this message "Firmware upgrade encountered an issue. Please select recovery mode in Kies & try again."
and i cannot boot to recovery mode on my device and cannot flash any thing :/
Click to expand...
Click to collapse
Try this one
https://m.youtube.com/watch?v=7zEhC4kvMUE
Goat678 said:
Well, the phone is not turning on.
While turning on shows this message "Firmware upgrade encountered an issue. Please select recovery mode in Kies & try again."
and i cannot boot to recovery mode on my device and cannot flash any thing :/
Click to expand...
Click to collapse
You fixed your problem?
Johnny TDN said:
You fixed your problem?
Click to expand...
Click to collapse
Unfortunately, no.
I still can't fix it
Goat678 said:
Unfortunately, no.
I still can't fix it
Click to expand...
Click to collapse
Then i'm afraid that you must buy a new motherboard. Sorry.
Johnny TDN said:
Then i'm afraid that you must buy a new motherboard. Sorry.
Click to expand...
Click to collapse
Well, i kept trying till i just flashed TWRP recovery, then installed your RedRom
and its very good!
Thanks ♥

GT-5100 looping on Samsung logo after flashing factory rom

Hi everyone.
My Galaxy Tab 2 10.1 was running on LineageOS 13 but it was very slow. I wanted to go back to official rom.
I used Odin 3.14.4 and flashed P5100XXDMD1_P5100DBTDMD1_P5100XXDLL2_HOME.tar.
Everything seemed fine (see log below) exept it doesn't boot!
It loops on the blue circle turning into the Samsung logo.
Re-flashing did not help.
The log:
Code:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Added!!
<ID:0/005> Odin engine v(ID:3.1401)..
<ID:0/005> File analysis..
<ID:0/005> Total Binary size: 1126 M
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> NAND Write Start!!
<ID:0/005> SingleDownload.
<ID:0/005> system.img
<ID:0/005> boot.img
<ID:0/005> cache.img
<ID:0/005> hidden.img
<ID:0/005> recovery.img
<ID:0/005> modem.bin
<ID:0/005> MLO
<ID:0/005> param.lfs
<ID:0/005> Sbl.bin
<ID:0/005> RQT_CLOSE !!
<ID:0/005> RES OK !!
<ID:0/005> Removed!!
<ID:0/005> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
wasThere said:
Hi everyone.
My Galaxy Tab 2 10.1 was running on LineageOS 13 but it was very slow. I wanted to go back to official rom.
I used Odin 3.14.4 and flashed P5100XXDMD1_P5100DBTDMD1_P5100XXDLL2_HOME.tar.
Everything seemed fine (see log below) exept it doesn't boot!
It loops on the blue circle turning into the Samsung logo.
Re-flashing did not help.
The log:
Code:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Added!!
<ID:0/005> Odin engine v(ID:3.1401)..
<ID:0/005> File analysis..
<ID:0/005> Total Binary size: 1126 M
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> NAND Write Start!!
<ID:0/005> SingleDownload.
<ID:0/005> system.img
<ID:0/005> boot.img
<ID:0/005> cache.img
<ID:0/005> hidden.img
<ID:0/005> recovery.img
<ID:0/005> modem.bin
<ID:0/005> MLO
<ID:0/005> param.lfs
<ID:0/005> Sbl.bin
<ID:0/005> RQT_CLOSE !!
<ID:0/005> RES OK !!
<ID:0/005> Removed!!
<ID:0/005> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
Click to expand...
Click to collapse
Force tab to recovery and do factory reset!
drnightshadow said:
Force tab to recovery and do factory reset!
Click to expand...
Click to collapse
I can't.
Power + volume up = reboot
Power + volume down = download mode
wasThere said:
I can't.
Power + volume up = reboot
Power + volume down = download mode
Click to expand...
Click to collapse
Try to redownload firmware... Something was wrong, if you can't access to recovery... Are you sure your downloading the right firmware for your tab?
And try using older odin... just an idea.
drnightshadow said:
And try using older odin... just an idea.
Click to expand...
Click to collapse
Good guess. Odin 3.09 worked better.
Now, power + volume up leads to recovery. I did the factory reset and then reboot.
It's fine.
Thank you very much (as I am too stupid to find the Thanks button!).
wasThere said:
Good guess. Odin 3.09 worked better.
Now, power + volume up leads to recovery. I did the factory reset and then reboot.
It's fine.
Thank you very much (as I am too stupid to find the Thanks button!).
Click to expand...
Click to collapse
Lol haha ... Thanks button he he .. I'm to lazy to update it
Anyway, it's nice to hear that you bring your tab back to life.
Try clicking like button instead of thanks

Categories

Resources