hello do you guys know a fix for this:
ODIN MODE (DT Load Fail)!
[UFDT] DT Entry: not found rev 0x1
[UFDT] DTB Load Fail
Do you how to fix it ?
Related
Hi, so here's my SGGP SM-G530FZ is off suddenly when I tried to turn it back but he remained on the logo so I tried the recovery mode but when I run it marked "
MMC: mmc_read fail
Movinand Checksum Confirmation Fail
ddi : mmc_read failed
ODIN MODE
PRODUCT NAME: SM-G530FZ
CURRENT BINARY: Samsung Official
SYSTEM STATUS: Custom
KNOX WARRANTY VOID: 0x0
QUALCOMM SECUREBOOT: ENABLE (CSB)
RP SWREV: S1, T1, H1, R1, A1, P1
SECURE DOWNLOAD : ENABLE"
only the download mode works but when I try to flash with Odin the latest firmware released for this one (4 files) with the pit it marks me "Re-partition operation failed" :crying: , if you wants screen or logs just ask . Thanks you for helping
[Translate (Fr to En) with Google Translate]
Nobody? :crying:
DEVICE NOTE EDGE SM-N915F
I have only access to Download Mode
No Recovery or Functional ROM installed
Problem: Every time it says "There is no Pit Partition"
Already tried Install with Odin (AP_N915FXXU1BOA2.tar and TBLTE_EUR_OPEN.pit) But Same Error.
-----------------------------------------------------
ODIN MODE
Product Name: SM-N915F
Current Binary:Custom
System Status:Custom
Reactivation Lock: Off
Knock Warrenty Void: 0x1 (4)
Qualcomm Secure Boot: Enable (CSB)
AP SWREV : S1 T1 R1 A1 P1
Secure Download: Enable
UDC Start
ODIN Flash Read Failure
Error: There is no PIT Binary
Secure Check Fail: PIT
ODIN: Flash Read Failure
-----------------------------------------------------
Are you flashing only PIT and AP, or the full set: PIT, BL, AP, CP and CSC?
Sent from my SM-N915G using Tapatalk
i am receiving this same issue. is there any way you can assist as i am a first time samsung user?
I am Having same issue on my Samsung Galaxy Note Edge.
Hello
I've bricked Oppo F1s when I've tried to flash it
this is infinity read info log
Wait for phone...
Phone found! [ 1087 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6755
BB_CPU_NME : [MediaTek] Helio[P10]|MT6755_S00
BB_CPU_EXT : 0xCB00 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x01000000
BromVer : 0x0005
BLVersion : 0x00FE
PreLoader : NOT Active [ Erased ]
BootLdrSS : SIGNED with SPRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
DAgent configured successfully
Connection agent : BROM
[DA_ERROR] : DRAM Configure failed!
ErroCode : 0x2122and I get this message error if I try to flash it with MT6750
Error: STATUS_INSUFFICIENT_BUFFER
EMICFG_NOT_ACCEPTED_CONFIG
Boot Error!
Operation Failed
Elapsed: 00:00:52
Reconnect Power/Cable!
Click to expand...
Click to collapse
it says that's an MT6755 processor , but when I try to flash it with Mt6755 with sp flashtool and NCK mtk soft it says that's version mismatch and it's and MT6750 device
Can you help to choose the right firmware please ?
octopus82 said:
Hello
I've bricked Oppo F1s when I've tried to flash it
this is infinity read info log
it says that's an MT6755 processor , but when I try to flash it with Mt6755 with sp flashtool and NCK mtk soft it says that's version mismatch and it's and MT6750 device
Can you help to choose the right firmware please ?
Click to expand...
Click to collapse
I have pretty much the same problem with my MOTO M (XT1662). It happened after I did the "Format whole flash" in SP flash tool.
Now the SP flash tool is giving me the following,
Chip Info
=======
Chip name: MT6755
Chip Version: 0x0000cb00
Ext Clock: EXT_26M
Extern RAM Type: DRAM
Extern RAM Size: 0xc0000000 (!!!)
SRAM Size: 0x00040000
EMMC Flash
=========
Boot 1 Size: 0x400000
Boot 2 Size: 0x400000
RPMB Size: 0x400000
GP1 Size: 0x0 (same for GP2, GP3 and GP4)
UA Size: 0x747c00000
No matter what ROM I'm trying to flash (stock or custom) , I always get the error "STATUS_INSUFFICIENT_BUFFER (0xC0010007)".
It looks like it has to do something with the External RAM Size (0xc0000000).
I found this firmware "XT1662_Kungfu_m_MT6755_USR_S0924_1612291517_mp7V2.3_CN (RepairMyMobile.in)", which seems to be what I need but I can't get pass this error.
Any help will be greatly appreciated.
i have the same problem
STATUS_INSUFFICIENT_BUFFER (0xC0010007)
i try to update with OTA and failed too
anyone can help ?
Samsung recovery
Code:
samsung a12zh/a12
10/QP1A.190711.020/A125FZHU1AYC3
user/release/keys
Install /sdcard/A12/stock/A125FXXU1AUC3_A125FOLM1AUC3_XSA.zip ...
Finding update package ...
Opening update package ...
Verifying update package ...
E: Footer is wrong
Update pkacage verification took 0.1s (result 1).
E: Signature verification failed
E: Error 21
Install from SD card completed with status 2.
Installation aborted. #1
PNG and TGY were also failed like is, but if reflashing stock ROM using Heimdall, which partitions are to be flashed accoring to the PIT on my A12? And which partitions should never be touched?
Even with successful flashes using Heimdall, it still always reports to me SW REV check failed
Now my device is still being boot-looped, and on either YouTube or online text tutorials nothing is about solving the boot loops for my A12
And have also retried to flash my own builds of TWRP instead, https://sourceforge.net/p/twrp-samsung-a12/code/ci/master/tree/out/target/product/a12, however also unfortunately somewhy,
Code:
Heimdall mode (High speed)
Product name: SM-A125F
...
Warranty void: 0x1 (0x500)
RP SWREV: B1 NS1 K1 S1
...
SW REV check fail: [recovery] Fused 1 > Binary 2
SW REV check fail: [boot]Fused 1 > Binary 0
Me again.. Ive obtained the same problem and solved it just reflashing my whole firmware with Odin u_u
I’ve just flashed the full firmware.
The SW REV check failures were fixed, but my device is still being boot looped
What to do next?
My A12 has MTK chipsets (according to my CPU-Z), hence also their ‘‘secure’’ boot locks, now going to unlock it by their SPFlashTool
speedmetal444 said:
Me again.. Ive obtained the same problem and solved it just reflashing my whole firmware with Odin u_u
Click to expand...
Click to collapse
Heimdall flashes are always by PIT partitions; PIT means partitioning informative tables
Odin flashes, on the other hand, are instead more by tar packages, namely BL, AP, CP, and CSC
* BL = BootLoaders; AP = Android PDA’s i.e. systems with also recoveries; CP = Core PDA’s i.e. modems; CSC = Country support codes or Consumer software customizations
I’m still being boot looped due to sth in unknown errors named PDP
Code:
Android recovery
samsung/a12nsxx/a12
11/RP1A.200720.012/A125FXXU1BUE3
...
Supported API: 3
# MANUAL MODE v1.0.0#
No commands specified
-- Wiping data ...
Formatting /data ...
E: [PDP] lstat /c___/pdp_b__: 0 - No PDP scenario
Formatting /cache ...
Formatting /metadata ...
Formatting /keydata ...
Formatting /keyrefuge ...
Data wipe complete.
hd_scania said:
Samsung recovery
Code:
samsung a12zh/a12
10/QP1A.190711.020/A125FZHU1AYC3
user/release/keys
Install /sdcard/A12/stock/A125FXXU1AUC3_A125FOLM1AUC3_XSA.zip ...
Finding update package ...
Opening update package ...
Verifying update package ...
E: Footer is wrong
Update pkacage verification took 0.1s (result 1).
E: Signature verification failed
E: Error 21
Install from SD card completed with status 2.
Installation aborted. #1
PNG and TGY were also failed like is, but if reflashing stock ROM using Heimdall, which partitions are to be flashed accoring to the PIT on my A12? And which partitions should never be touched?
Even with successful flashes using Heimdall, it still always reports to me SW REV check failed
Now my device is still being boot-looped, and on either YouTube or online text tutorials nothing is about solving the boot loops for my A12
And have also retried to flash my own builds of TWRP instead, https://sourceforge.net/p/twrp-samsung-a12/code/ci/master/tree/out/target/product/a12, however also unfortunately somewhy,
Code:
Heimdall mode (High speed)
Product name: SM-A125F
...
Warranty void: 0x1 (0x500)
RP SWREV: B1 NS1 K1 S1
...
SW REV check fail: [recovery] Fused 1 > Binary 2
SW REV check fail: [boot]Fused 1 > Binary 0
Click to expand...
Click to collapse
The error at the last is probably because the firmware you are trying to flash has older bootloader than what it is currently and it looks like you cannot downgrade bootloader.
I
My phone show me this
ODIN MODE (DT Load Fail)!
[UFDT] DT Entry: not found rev 0x1
[UFDT] DTB Load Fail
vol up + power
press for 10 sec or more
try this
mieucun123 said:
Ponsel saya tunjukkan ini
MODE ODIN (Pemuatan DT Gagal)!
[UFDT] Entri DT: tidak ditemukan putaran 0x1
[UFDT] Beban DTB Gaga
Click to expand...
Click to collapse
mieucun123 said:
My phone show me this
ODIN MODE (DT Load Fail)!
[UFDT] DT Entry: not found rev 0x1
[UFDT] DTB Load Fail
Click to expand...
Click to collapse
did you succeed? I also experienced this
My phone show me this
ODIN MODE (DT Load Fail)!
[UFDT] DT Entry: not found rev 0x1
[UFDT] DTB Load Fail
If its an mtk device you can use test point to put it in brom and flash with mtkclient. It uses cmd and a lil more tedious but it saved my a125u. Actually used it to convert to a125w xac to unlock the bootloader and all that