I've got this box from my cable operator.
It has a pretty powerful Amlogic s905x3 processor but I'm not sure about the amount of RAM.
There is no reset button in the AV hole.
Is there a way to flash the box with a different firmware or at least run Coreelec?
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Well, this box has adb access enabled by default. Even root I was able to issue settings command which enabled me to access package installer to install button mapper and then assign home key. Then I added leanbackonfire launcher to bypass the default one. I installed the apps I needed and they work fine even though there are no Google play services.
can you extract the default Live TV app from this box ?
guess this is the only box which can make use of DVB tuner using TIF .
I can if you tell me where to look for it. There is some kind of provider launcher app which starts the tuner and shows channels and enables tuning to them via dvb-c tuner. I saw the live TV app somewhere in the apps.
I used X-plore to copy apks. They seem to be fine.
hi can anyone tell me howto access terminal for this board does it go over otg?
If you are running firmware from February this year, adb access is open and you can log in as root. There have been some reports of firmware update that closes this hole but I haven't received it yet. Make sure your box is on to connect to it.
it works thanks will install leanbackonfire launcher, is there any custom roms for this board?
I suggest you install Wolf Launcher because it's lighter than leanbackonfire. The box is encrypted and there is no reset button. I tried to boot TWRP but it didn't work. The bootloader probably only installs signed zips.
thanks for the advice.
is there anyway to stop it from updating firmware been searching trough services cant find it?
The don't use Updater I think because I started it manually and searched for updates but there were none. I think the update comes from the cable system. I think all your installed apps will be there even after update. You may just loose the ability to log into the box.
Is there a way to access the android at all, my operator doesn't let me do anything, it starts it's own app immediately by default and u don't have access to android at all.
Supernova Move box software modding
Ovo uputstvo će vam pomoći da pretvorite Supernova Move box u Android box. I dalje ćete moći da koristite box za šta je predviđen – gledanje kablovske televizije sa dodatkom Android dela. Sve što budete radili, radite na sopstvenu odgovornost jer može doći do brickovanja boxa mada je to malo...
forum.benchmark.rs
kalehrl said:
Supernova Move box software modding
Ovo uputstvo će vam pomoći da pretvorite Supernova Move box u Android box. I dalje ćete moći da koristite box za šta je predviđen – gledanje kablovske televizije sa dodatkom Android dela. Sve što budete radili, radite na sopstvenu odgovornost jer može doći do brickovanja boxa mada je to malo...
forum.benchmark.rs
Click to expand...
Click to collapse
Thanks i hvala
Hi guys,
I have a problem with my device. I'm trying to install the wolf launcher and button mapper. My device got a firmware update that locked enabling USB debugging I haven't enabled it before the update. I have tried with ADB (over USB and WIFI) but without success. Over wifi, I can ping my device but I can't connect to it. The error is "No connection could be made because the target machine actively refused it. (10061)". The next solution which I have tried is creating a zip file with TWRP example which contains META-INFO and system folders. In the system folder, i added apk files for the wolf launcher and button mapper. I entered into RECOVERY mode and tried running update from USB but I have got the error "Signature Verification error (21)" Do you have a solution for installing a launcher on this device?
You could try enabling CEC on the box and then use your TV remote to access settings. From there you can go to apps and by using file browser or apk installer install the launcher from USB. Unfortunately, not all TV remotes can trigger settings menu on the box. My Hisense smart tv remote can't but some Samsung and LG can.
kalehrl said:
You could try enabling CEC on the box and then use your TV remote to access settings. From there you can go to apps and by using file browser or apk installer install the launcher from USB. Unfortunately, not all TV remotes can trigger settings menu on the box. My Hisense smart tv remote can't but some Samsung and LG can.
Click to expand...
Click to collapse
so it can be done only on Smart TV?
If you can access recovery, you can downgrade to older fw with adb access.
i don't have access throw adb even in recovery
Some people say that they can go into recovery by keeping the power button pressed and plugging in the power adapter. If you can get into recovery, I can send you the old fw with adb access to flash in recovery. Downgrading fw works fine.
Related
FOR FROYO GOTO THIS LINK ......
.
Hi Guys
Here is a guide to show you how to connect your HTC to Ar Drone just as an iPhone would do. This is for GINGERBREAD only , if you are on FROYO goto this link .
Currently Android does NOT support AD-HOC Networking
Till now I was usung the Manual Infrastructure way which needed a PC Telneting to the AR DRONE to connect to my HTC Wifi Hotspot each time powering on the Ar Drone. This means I had to carry with me a PC each time I want to Power on the AR Drone. Also the HTC WIFI Hot Spot had a limited wireless reachable range so the AR DRONE would easily get disconnected ....
Here is what you need to do , no more PC`s needed once you follow this guide.
P.S. none of this below is my invention, I just searched & found it here and there and complied a guide for you guys.
Here is what you need :
1) A Rooted HTC DESIRE HD or any other HTC
2) Your HTC must be on GINGERBREAD Rom
3) Adroid SDK
4) ROM MANAGER with Clockworkmod 3.x.x.x
5) AR.Pro or ARDrone Demo, Application from Market
6) ADHOCv2.zip file
7) Wifi Tether from market
8) Obviously an Ar Drone
Explanation of everything
#1) and 2) and 3) are Obvious
#4) Most current Rom Managers are on Clockworkmod V. 3.x.x.x , so it`s OK, if you`re on 2.x.x.x you might want to upgrade to 3.x.x.x from rom manager.
#5) Just Download from Market, there is another one called ARDroid but I could not get it working with AR Drone yet.
#6) First download this file "ADHOC.v2.zip " and then put this file on the root of your SD CARD . Once this is placed on the root of your SD CARD , open ROM MANAGER (make sure it`s running 2.5.1.3 or Green Text colour in Recovery) and click REBOOT INTO RECOVERY. Then INSTALL ZIP FROM SD CARD and choose this file ADHOC.v2.zip and flash it into your HTC. Once flashed turn on your AR DRONE and try to see it in the WIRELESS NETWORKS on your HTC , it should look something like this.
" (*)ardrone_XXXXXX "
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
If you see this then click to connect and wait for it to connect . Once connected you can disconnect BUT do not press FORGET THIS NETWORK , keep it in the memory of HTC.
IMPORTANT : Take a note of your AR DRONE`s network SSID , you will need it later on . Mine is 'ardrone_124923'
#7) Goto this link and download the latest .apk of WIFI TETHER or goto market and try to download it from market, I think Market does not have the latest one. Once downloaded the .apk, place it in the root of your SD CARD or DOWNLOAD folder, locate it and install it using "Astro"
Now Start the WIFI TETHER, then do the following
MENU > SETTINGS > CHANGE SETUP METHOD > into WEXT (adhoc)
MENU > SETTINGS > SSID > into "ardrone_XXXXXX" xxxxxx being your AR Drone`s number that you noted down a few lines above.
MENU > SETTINGS > CHANGE LAN > into 192.168.1.0/24
MENU > SETTINGS > Routing Fix > Must be ticked (I don`t know why but it works like that)
Now press BACK and goto "PRESS TO START TETHERING" and press the sign there
Then the SIGN turns into YELLOW meaning all is OK , if you encounter ERRORS on the screen , Turn OFF/ON the wireless Tether once more, if you still encounter errors then UNINSTALL and REINSTALL WIFI TEHTER. You can check to see if there are any errors from MENU > SHOW LOG
P.S. MAKE SURE YOU ALLOW ALL REQUESTS THAT SUPERUSER.APK IS ASKING PERMISSION FOR !!!
We are almost ready !!!!
When the WIFI TEHTER is on, meaning YELLOW , turn on the AR DRONE and wait for it`s lights to be all GREEN . Once all GREEN then goto AD.PRO or ARDrone Demo application and start the application , that`s it ..... (make sure the default IP address is 192.168.1.1 on your aplication)
For the future uses you only need to turn on WIFI TETHER and then turn on the AR DRONE once all lights are green then open your favorite AR DRONE application and fly away ....
Enjoy !!!
Hi!
Any chance you make a version for Nexus S (Gingerbread also...) ?
I've tried this with a laptop ad hoc network, my device finds it on the WIFI networks but can't connect to it.
I'm getting my AR.Drone in a couple of days so I'd love to know it's going to actually work
Hi
I don`t have a Nexus S , but I am almost sure this method MUST work on all android devices, just do exactly as I say and you should be OK.
You don`t need a Laptop to connect, just do exactly as I mentioned and should work....
BTW , are you rooted ?
doublecheese said:
Hi
I don`t have a Nexus S , but I am almost sure this method MUST work on all android devices, just do exactly as I say and you should be OK.
You don`t need a Laptop to connect, just do exactly as I mentioned and should work....
BTW , are you rooted ?
Click to expand...
Click to collapse
I'm rooted.
Got AR.Drone.
Tried your script on stock android 2.3.4, didn't work...
Flashed SupeAosp 8.2 and I didn't even have to use WiFi tether... just connected to the drone ad-hoc wifi network and ran the AR.Drone app.
I Know why you here ??
you bought SuberSonic sc-66g Internet Tv Box but there is no support from this company ,that sad ,i have the same problem .but you know that this box not SuperSonic box ,its actually for company called peal its a German co.
supersonic don't support it .but the manufacture for this box is peal and they sell it by the name of Meteorit MMB-322 HDTV where they support it and and upgrade it ,anyway her is the link for this company
http://www.pearl.de/support/s50t.jsp?query=MMB-22&query_type=1
we will need it when we update the box.
anyway .here we will Root the box and update it
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
lets start
Root the box
we need some programs
1-Android SDK should be installed in your PC ,if you don't have it here is the link
http://developer.android.com/sdk/index.html
2-MMB-322 Toolbox =to connect to the box by the box IP ,here is te link
http://www.multiupload.com/CK3COYEOF2
thanks to M1cha in Germany for this tool.
to root it its very simple
1 - you need to know the box IP
2-unzip MMB-322 Toolbox to any folder in your desktop and run MMB322-Toolbox.jar,widow should pop up look like this
http://img52.imageshack.us/img52/1527/infosl.png
3-go tools and hit su install,then superuser.apk install and you can install the market .
the box will reboot after you install the market .
now you rooted
ps . to know the IP for the box .
if you have Verizon go to your browser (chrome or ie ..)and inter this address HTTP://192.168.1.1 ==window pop up ask for username and the password
the default
username =admin the password=password and you will see all connected devices to you you network .
if you have Comcast use HTTP://10.0.0.1 ---and the same way .
UPDATE the Firmware
Note: that the logo will change from supersonic to Meteorit ,but its the same Firmware.
you need
1.7z program ===to change the script
2.MMB-322 Toolbox ===to root it after
3-USB flash drive any size over 256 MB formatted to fat32
4 -the latest Firmware from peal here http://www.pearl.de/support/s50t.jsp?query=MMB-22&query_type=1
the latest is Firmware for PX1534
install
1-download the Firmware =unzip to any folder inside the zip file you have online_upgrade_img folder =open it
2-open emergency_recovery.sh with notepad
change this script from 0 to ?
like this
$0`if [ $0 -eq ? ] to $?`if [ $? -eq ? ] save and close
if you don't do that supersonic box will not update and it will give you this massage infited image i/o error and the update will failed.
3-open ouimg.bin with 7z ==go to folder indep_rootfs =open it =you will find
this file emergency_recovery.sh again with 6 other files end with .sh open them one by one useing notepad and change this script from 0 to ? and make sure
a-you save them after you change each one .
b- 7z manager save the changes .
4-copy the whole folder (online_upgrade_img) to your formatted USB flash drive
5- in the box go settings =system upgrade =local device ,the box will reboot to recovery =insert the USB flash drive and don't worry i take some time .
ps .it it take more than 5 minuets , unplug and keep the USB in the box ,plug it again and restart ,it will take to recovery again .
6-push enter in you remote when you see the update.
7-let it install when it done it reboot ,remove the USB drive and you done
good luck
if you need more info go to .
Meteorit- Wiki
http://meteorit.wikia.com/wiki/Meteorit-_Wiki
factory upgrade instuctions
1st
Unzip the contents of the downloaded zip file into a
any folder on your PC.
2nd
Copy the unzipped folder named
"online_upgrade_img" and its contents to an empty USB memory stick
and plug the USB memory stick and then into the meteorite
TV Box.
3rd
Now select the main menu of the meteorite TV box, select
"Settings" then "System Upgrade" and then "Local
Devices ".
4th
Now select "System Upgrade" and confirm the upgrade
with the "Enter" key on the remote control of the meteorite TV box.
Please disconnect the device during the update process by NOT
Mains! Wait until the process is complete.
Following the installation will start the Android TV Box
automatically before they get you with the improvements from the
Update is available.
Wait about 15 seconds until the WLAN is turned on automatically.
Cherry Mobile Android is one of the Cheapest Android Phones developed in Philippines.
This time i will guide you of how to root your CHERRY MOBILE CLICK & FLARE
BEFORE ROOTING YOUR CM PHONE:
WARNING: Rooting can brick your phone and will also void its warranty. Do it at your own risk. I'm not responsible for any possible damage that may happen to your device.
Download to your computer this Root Tools.zip file that contains PdaNet for Windows 7/8/XP & Vista with Root and Restore by Bin4ry> DOWNLOAD
Unzip the file downloaded with winrar HERE
Put everything in one Folder.
For Windows 7/8/Vista, after unzipping, right click RunMe then click on Properties > click the Compatibility tab > check Compatibility and set it to Windows XP SP3 > Ok
Then Enable USB debugging on your phone. Go to Settings > Developer Options > USB Debugging.
Also Enable "Stay Awake" for you to be able to see if your phone is responsive.
Do not connect your phone to the computer yet until you are prompted.
ROOTING PROCESS
On your Computer/Laptop, double click on PdaNetA4126 and continue with the installation until you see a pop-up message like the one below.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
*Select Others then click OK.
*If Prompted, a warning message will appear that says "Windows can't verify the publisher of this driver software." Then Click "Install this driver software anyway" or "Reinstall Drivers" sample image Below.
*PdaNetA4126 will now ask you to connect your device to the computer. Connect your phone to your computer via USB cable. Don't enable any modes like USB storage, and etc.
Let the driver installation complete,dont do anything but let it finish first.
*After Finishing Instatallation of drivers. On your PC again, double click on RunMe.bat.
Image sample below:
View attachment 1974817
*A command prompt window will pop-up. Press 1 and hit the Enter.
*If you want to unroot, simply type x and hit enter.
*On your phone, tap “Restore my data”, this will reboot your phone, wait for your phone to be fully ready. Entering password is unnecessary, just hit “Restore my data” before it reboots itself. (as for what i experienced, my phone rebooted itself after 5seconds without having the chance of hitting Restore button)
==If your phone reboots without pressing the Restore Button, You need to reboot the phone by pulling out the battery and putting it back and re-run/re-install everything from the start for another fresh root process, because your phone and drivers may not be responsive after failure of attempt and you may also fail to root without doing it.It may also brick your phone.==
*On your computer, the command prompt will require you to press any key to continue.
Congratulations!!! You've successfully rooted your Cherry Mobile Click/Flare!!! Check your apps and look for Supersu App
To check if you have successfully rooted your phone, download Root Checker HERE
To remove Unnecessary Apps (Bloatwares) that causes to slow your phone down, here is the perfect app DOWNLOAD HERE
it will allow you to remove unnecessary apps such as e-warranty, cherry fun club and more. its free and friendly user app, just dont fool around with your system apps that may be linked to your system processes, if you delete the wrong file accidentally, luckily, this app provided itself a recycle bin that may allow you to restore the recent deleted file. think before you delete it completely out of your phone system.
Deleting apps frees more memory (depends on the size of apps you deleted.)
Hit Thanks if Helpful..
gagana bato sa cherry mobile astro or sa CLICK and FLARE lang tlga?
marunong bah kayu mag root nang cherry mobile ace 2 ? kasi di ko makita kahit saan !
pa kishare lng po kung alam nyu ...! thank you !
Cherry Mobile Flare J3 Plus
meron na po ba tayong rooting process para sa cherry mobile flare j3 plus? any certain twrp or cwm? gusto ko sanang mag root ehh kaso walang working na one click root, kay gusto ko sana mag try via adb process. prob naman is wala akong makitang certain twrp or cwm para sa cherry mobile flare j3 plus..thanks sa makakapag bigay ng any information about this comment..
How to root cherry mobile flare j3s plsss help me
it would work also in cherry mobile flare a2 lite?? thanks
Sino may root na cherry Mobile click? Pede pa pull Ng keypad apk nya? Salamat
Hello,
I installed this rom "nethunteros-nethunter-hammerhead-cm-14.1-hammerhead" and I installed this package "kalifs-armhf-full.tar.xz" in the chroot manager via "NetHunter" on my Nexus5
My wifi usb stick externally via the otg, works very well.
But I cannot put my internal wifi card in "Monitor" mode.
The "NetHunter" application also tells me that I do not have a HID interface.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Which means that the "DuckHunterHID" does not work, neither does "Rucky".
Especially when I launch the "Nexmon" application, as soon as I try to install the pack on the home screen and the application crashes and stops instantly.
How can I fix the problem?
Thank you
A +
andurilmike said:
Hello,
I installed this rom "nethunteros-nethunter-hammerhead-cm-14.1-hammerhead" and I installed this package "kalifs-armhf-full.tar.xz" in the chroot manager via "NetHunter" on my Nexus5
My wifi usb stick externally via the otg, works very well.
But I cannot put my internal wifi card in "Monitor" mode.
The "NetHunter" application also tells me that I do not have a HID interface.
Which means that the "DuckHunterHID" does not work, neither does "Rucky".
Especially when I launch the "Nexmon" application, as soon as I try to install the pack on the home screen and the application crashes and stops instantly.
How can I fix the problem?
Thank you
A +
Click to expand...
Click to collapse
I wrote you a very detailed tutorial, but if you don't read it it will not magically be solved, mate. ;/
https://forum.xda-developers.com/google-nexus-5/help/problem-tl-wn722n-1-10-nexus-5-6-0-1-t4022565
I told you that the rom isn't the right one...earlier that only the _old and "smaller"_ kalifs builds are working with this build, so they do not crush the entire install.
Hid most likely will not work, here as well.
But the usage of the internal WiFi chipset + external adapter with supported chipset are working fine.
If you have trouble understanding use a translator or just ask in your 1st thread.
No need to open one here and on gitlab.
Best of luck
I finally install LOS-hammerhead-14.1-20170102-nethunteros + the last kali-fs released on the site https://build.nethunter.com/kalifs/kalifs-latest/.
Is I have both HID interface, it works wonderfully with Rucky and DuckHunterHID.
My TL-WN722N in OTG works perfectly.
I installed Nexmon and I still can't put my bcm 4335/4339 wifi chipset in monitor mode.
I tried to patch the firmware via Nexmon but it cannot find the firmware "no such or directory".
What date do you recommend kali-fs in hammerhead?
https://build.nethunter.com/kalifs/
Thank you
A +
andurilmike said:
I finally install LOS-hammerhead-14.1-20170102-nethunteros + the last kali-fs released on the site https://build.nethunter.com/kalifs/kalifs-latest/.
Is I have both HID interface, it works wonderfully with Rucky and DuckHunterHID.
My TL-WN722N in OTG works perfectly.
I installed Nexmon and I still can't put my bcm 4335/4339 wifi chipset in monitor mode.
I tried to patch the firmware via Nexmon but it cannot find the firmware "no such or directory".
What date do you recommend kali-fs in hammerhead?
https://build.nethunter.com/kalifs/
Thank you
A +
Click to expand...
Click to collapse
You use this kalifs build:
https://build.nethunter.com/kalifs/release/kalifs-armhf-full.tar.xz
Afterwards don't use the Nexmon app, mate.
If you want to set the internal chipset into 'monitor mode', type
source monstart-nh
To stop run:
source monstop-nh
If you want to run airodump-ng for example, type
airodump-ng wlan0
For wifite
wifite -i wlan0
Good luck and have fun
Thank you !!!
Everything works flawless.
I have the full pack, Wifi in OTG + HID interface + Monitor Internal Wifi
andurilmike said:
Thank you !!!
Everything works flawless.
I have the full pack, Wifi in OTG + HID interface + Monitor Internal Wifi
Click to expand...
Click to collapse
I'm glad to hear that, mate!
Hit the "thanks"-button, if you like..
andurilmike said:
Hello,
I installed this rom "nethunteros-nethunter-hammerhead-cm-14.1-hammerhead" and I installed this package "kalifs-armhf-full.tar.xz" in the chroot manager via "NetHunter" on my Nexus5
My wifi usb stick externally via the otg, works very well.
But I cannot put my internal wifi card in "Monitor" mode.
The "NetHunter" application also tells me that I do not have a HID interface.
Which means that the "DuckHunterHID" does not work, neither does "Rucky".
Especially when I launch the "Nexmon" application, as soon as I try to install the pack on the home screen and the application crashes and stops instantly.
How can I fix the problem?
Thank you
A +
Click to expand...
Click to collapse
use custom kernel
Twitch: Livestream (Ad-Free)(Android TV)
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Attached is 1 zip files. Since twitch is using split apk we need to use "Split APKs Installer (SAI)" found in the google play store to install the applications. It does not require root.
Versions:
Twitch [2.9.8](AndroidTV) (newest as of 3/7/2020)
Tests:
Tested on Nvidia Sheild TV PIE
Instructions Android TV:
1) Download the ZIP file for Android TV onto your internal SD-Card
2) Install Split APKs Installer (SAI) either from the playstore or attached to this post.
3) Open Split APKs Installer (SAI) and go to settings and enable sign APKs(see screenshot)
4) Go back to Main Screen and hit Install Apk at the bottom
5) Locate ZIP file you copied to your internal SD-Card
6) You will get a notification that you need to allow Split APKs Installer (SAI) to install the file(on android TV after enabling install permissions I need to close and restart from setup 3 as giving permissions froze the app)
7) Run Twitch and sign in
NOTE:
1) Make sure you uninstall any twitch app you have installed
2) While the application stops ads from twitch it may not stop forced ads(Ads that the streamer forces). Example, switch from streamer to streamer you will get a ad from twitch(this should be blocked). Streamer finished a match in overwatch he may force a ad on his viewers(this may not be stopped)
Looking to fix phone to newest version. Some set backs.
AFH DOWNLOAD:
Twitch [2.9.8](AndroidTV).zip
Github Split APKs Installer (SAI)
or
Google Play Split APKs Installer (SAI)
Not working
Yo, i did all your steps, but the 1st stream i launched showed me an add...
I tried to clean cache.... still nothing
I've an S10 with android 10
Jeanestmare said:
Yo, i did all your steps, but the 1st stream i launched showed me an add...
I tried to clean cache.... still nothing
I've an S10 with android 10
Click to expand...
Click to collapse
I've been running it for a few days now with not a single ad but I'll run some tests to see if I can reproduce. Also just to be clear you got a ad at the start of the stream? And you did uninstall any previous versions before installing?
t436h05t said:
I've been running it for a few days now with not a single ad but I'll run some tests to see if I can reproduce. Also just to be clear you got a ad at the start of the stream? And you did uninstall any previous versions before installing?
Click to expand...
Click to collapse
Yes, i got the ad at the beginning of the stream. I've cleaned and uninstalled every older versions before.
Jeanestmare said:
Yes, i got the ad at the beginning of the stream. I've cleaned and uninstalled every older versions before.
Click to expand...
Click to collapse
Had to revert to a slightly older version for phone only. Working out the issues. Updated the link for phone above let me know if you have issues.
Thank's but i was already using 8.7.0 without ads, so not usefull for me to downgrade to 8.6.1 ?
Jeanestmare said:
Thank's but i was already using 8.7.0 without ads, so not usefull for me to downgrade to 8.6.1 ?
Click to expand...
Click to collapse
Removed phone till I can fix it. Limited time atm. I'll update the post when I mod the new phone app.
Thanks
It works well on my shield tv.
I got this message when press start to installation! Beelink GT King
does this support background or mini player? Like can i have it running in a small window while doing other things on my phone?
Application is incompatible with this device
it may mostly work on Shield, but others may not work as good with Android TV
Tried it on my Mecool Km9 running Pie but wouldn't install, Need the 32 bit one. Could you do the same thing to this 32bit app. You can download it from my Google drive https://drive.google.com/open?id=1S_r_Hv2qkQPZjEUnYRKn2gvN1DtsOrpV
Do you think it will work with a Android TV from Philips with pie?
If he would be able to do it?
3.1.0: solidfiles (dot) com/v/2wy7R6WmdQ6yR
Impossible to install!!!