Anyone have MXQ PRO 4K Allwinner H3 XR819 Firmware? - General Questions and Answers

Hello
I have an MXQ pro 4k that's bricked and gets stuck on boot animation. It has allwinner h3 CPU and XR819 WiFi chip.
I can't enter recovery with av button because it just gives blackscreen and no light from led after that and I can't find firmware for it (Android 7.1.2).
Can anyone help me get to recovery and provide the right firmware to make it work again?
Thanks in advance

i am desperately searching the rom for months to give my ****ty tv box a life again.

iwingmusic said:
i am desperately searching the rom for months to give my ****ty tv box a life again.
Click to expand...
Click to collapse
Custom firmware https://forum.xda-developers.com/t/rom-atv-mod-2019_build-allwinner-h3-mxq-4k-5g-mod-tv-rom.4295863/ https://drive.google.com/file/d/11MZ4_ZXGfCCqRs_9tx_zE0FPlUgcmgw7/view

Ramaga said:
Кастомная прошивка https://forum.xda-developers.com/t/rom-atv-mod-2019_build-allwinner-h3-mxq-4k-5g-mod-tv-rom.4295863/ https://drive.google.com/file/d/11MZ4_ZXGfCCqRs_9tx_zE0FPlUgcmgw7/view
Click to expand...
Click to collapse

Supernova76 said:
Hello
I have an MXQ pro 4k that's bricked and gets stuck on boot animation. It has allwinner h3 CPU and XR819 WiFi chip.
I can't enter recovery with av button because it just gives blackscreen and no light from led after that and I can't find firmware for it (Android 7.1.2).
Can anyone help me get to recovery and provide the right firmware to make it work again?
Thanks in advance
Click to expand...
Click to collapse
I had the same problem with the same specs as yours, and believe it or not here's how I solved this cursed box... with some magic!!
1) Plug a USB male to male cable to the USB port #4 in your TV box and the other end of the cable to the PC.
2) Plug the power cable to the TV box.
3) Watch the damn thing go back to life.
At least, this is how it worked for me.
I still can't access the bootloader through the AV micro switch.
And based on this solution I assume it has to do with some electrical problem, maybe the ac adapter is not delivering the needed power to the board in order to propertly boot up? hence by connecting to the USB port #4 the board takes the needed power? (you can see this by simply leaving the USB connected between the tv box and the pc and unpluging the power adapter... the tv box will remain powered... weird eh?

Ramaga said:
Кастомная прошивкаhttps://forum.xda-developers.com/t/rom-atv-mod-2019_build-allwinner-h3-mxq-4k-5g-mod-tv-rom.4295863/ https://drive.google.com/file/d/11MZ4_ZXGfCCqRs_9tx_zE0FPlUgcmgwBalneario
Click to expand...
Click to collapse
contraseña
Mod translation: password

tonyarevalo said:
contraseña
Mod translation: password
Click to expand...
Click to collapse
como obtener la contraseña?

Related

Lenovo a850 china hard bricked, need help.

Hi..
A phone shop bricked my phone. Now it is not powered on if the battery inside. It also not power on without battery, but atleast when i connect it to USB http://telewizor.eu/displaylink.html , the red light at the phone (near camera) turn on. The pc also not detecting the phone.
Is there any way to fix it or flash it since it is not detected?
TQ
Will someone help?
kuszmania9999 said:
Will someone help?
Click to expand...
Click to collapse
maybe you have flashed wrong ROM. be careful not to confuse with ROW or CN rom. try press VOLUME UP + VOLUME DOWN and connect usb cable to your PC. works with mine.
sahniana said:
maybe you have flashed wrong ROM. be careful not to confuse with ROW or CN rom. try press VOLUME UP + VOLUME DOWN and connect usb cable to your PC. works with mine.
Click to expand...
Click to collapse
Wow....finally a reply, nevermind, i already managed to solved it by myself.
Hello,
I also having this issue and just fixed it.
See thread here :
http://forum.xda-developers.com/lenovo-a850/help/lenovo-a850-wont-power-flashing-rom-t3322646
Good Luck!

USB_Burning_Tool - error

HI,
i have Amilogic M805, Wifi is AP6212
on the board is: Netxeon MK808Q_V10-20140822
On the cover is MINI TV form android Quad - Core MK808B Plus
If i tried USB_Burning_Tool
I have error [0x10105002]Romcode/Initialize DDR/Read initialize status/USB Control setup error
Why ?
czmirage said:
HI,
i have Amilogic M805, Wifi is AP6212
on the board is: Netxeon MK808Q_V10-20140822
On the cover is MINI TV form android Quad - Core MK808B Plus
If i tried USB_Burning_Tool
I have error [0x10105002]Romcode/Initialize DDR/Read initialize status/USB Control setup error
Why ?
Click to expand...
Click to collapse
I had the same problem with S905 when use defective usb flashing cable. and try redownload firmware
Such_A_Victor said:
I had the same problem with S905 when use defective usb flashing cable. and try redownload firmware
Click to expand...
Click to collapse
i try 2 cables and 2 computers
windows 10 64bit
a windows xp 32bit
same error.
I had same problem with M8S android box, through trial and error and an hour of pulling my hair out, I tried this, Amlogic burning tool, Toothpick method and male to male usb cable. (Leave toothpick in AV hole )After releasing the toothpick and pressing start the error comes up after 2% I quickly pressed the toothpick in again to see what would happen and boom it started to burn the firmware on, maybe luck i dont know but box back up running.. Hope it works for others..Des
how you fix that error? Romcode/Initialize DDR/Read initialize status/USB Control Setup Error
Same problem with MXIII 4k =(
Had the same problem, shortened the USB cable (that i made myself) to 15Cm, then it worked, signal integrity ?
first put the rom you will use, then press start, only then plug the device into the USB port. Worked with me having the same problems.
work for me... redownload firmware
Code4power, a link please for download the img
Had same issue with MXS Plus unit.... Tried a different USB-USB cable and now up and running. MANY THANKS TO ALL ON HERE
uncheck erase flash and bootloader in amlogic tool and that should fix your problem
renzenar said:
uncheck erase flash and bootloader in amlogic tool and that should fix your problem
Click to expand...
Click to collapse
Worked like a charm. Thanks
thank youuuu
renzenar said:
uncheck erase flash and bootloader in amlogic tool and that should fix your problem
Click to expand...
Click to collapse
THanks its work for me
I cannot get past that error. I have tried 3 different computers and various different versions of the burning tool as well as unchecking the boxes suggested above. So frustrating.
x96pro +
Awkomo said:
I cannot get past that error. I have tried 3 different computers and various different versions of the burning tool as well as unchecking the boxes suggested above. So frustrating.
Click to expand...
Click to collapse
I had the same issues as described above, and I simly just changed the cable lenght from 1.5m to 30cm and the box started flashing itself from the burning tool!
I got a shorter cable but it still does it for me
So guys after going crazy did this - Tried the Nand Method on a95x. Sequence - Upload your image to USB burning tool (don't hit start) - connect USB A to A cable (didn't connect) - Flash Pins 5-6 or 6-7 - Now USB tools see's the box but don't hit start yet - because usb power is not enough to burn it - Now insert the toothpic to hit the reset button - Now connect power while toothpic is inserted - Viola - the box starts burning - This is a sure to work method - everytime.
jahjahjah said:
So guys after going crazy did this - Tried the Nand Method on a95x. Sequence - Upload your image to USB burning tool (don't hit start) - connect USB A to A cable (didn't connect) - Flash Pins 5-6 or 6-7 - Now USB tools see's the box but don't hit start yet - because usb power is not enough to burn it - Now insert the toothpic to hit the reset button - Now connect power while toothpic is inserted - Viola - the box starts burning - This is a sure to work method - everytime.
Click to expand...
Click to collapse
Dear, i tried this method as well...but no luck. please advice..., if possible please share the link for usb burning tool and the firmware for MXQ PRO+ model. Will try fresh. Would highly appreciate ur help...
Had the same problem with mecool km9.
Tried all with no luck, then i tried to disconnect the box, close then restart usb burning tool, load the img file, unchecked erase flash and erase bootloader, hold the reset button with toothpic, then connect the box, hit refresh, and after that, start the flashing process.
So, if you tried to uncheck erase... like i did, you should try to disconnect the box, as it doesn't seem to register the unchecking without that.
:good:
You can see how many failed i had before disconnecting/reconnecting the box !

Emish X700 Android TV box KK 4.4.04

Hi I bought on ebay android tv box called Emish X700. Once i went for holiday and disconnected TV box from power outlet. After 2 weeks i came back home and when i turned it on TV box get stucked with picture of dead android without any option. I tried to do reset with toothpick for 10 sec in hole but with no change. when i googled a bit i found tools and firmware which helped me to restore this TV box to factory state and to be able to use it again. That's why i'd like to share it with users with same or similar problem.
Firmware + Flash tools + Drivers
Steps.
1. download attached files
2. unpack it
3. follow instructions from document in "X700 upgrade" folder
4. in case your PC can't detect your device use "Android Tool" flasher with firmware from "X700 upgrade" folder
5. after successful flashing device will reboot and will be booting for about 15 mins, so be patient
Where can I find Android Tool?
I did the step but in the program for firmware update the label does not become Green, so can't detect the device
Android tool is possible to download from link in 1st post. to get green status in program you have to plug usb cable connected already to your computer to your box with pressed resset button for abbout 5 secs.
I did for 10 seconds but nothing happens
Edit: it work, thank you very much for the guide!!
need you help
Leoxur said:
I did for 10 seconds but nothing happens
Edit: it work, thank you very much for the guide!!
Click to expand...
Click to collapse
I have the same problem, PC does not recognize the device.
I downloaded both folders for update.
Can you pls explain how to do it .
Thanks
mathuzalem said:
I have the same problem, PC does not recognize the device.
I downloaded both folders for update.
Can you pls explain how to do it .
Thanks
Click to expand...
Click to collapse
You have to use the tool for flash, not the program where the label should become green.
hello I have a box Emish x700 I can not have the update I have a USB transfer cable to connect two pc via usb but I do not have a green box in your software and it does not see my device on both thank you flash software
kevintrophy said:
hello I have a box Emish x700 I can not have the update I have a USB transfer cable to connect two pc via usb but I do not have a green box in your software and it does not see my device on both thank you flash software
Click to expand...
Click to collapse
Read my previous post!!
I get the error IDB failed in android tools, what can I do?
Thanks for this! I've been searching everywhere.
Device not recognized using the tools.
I have an Emish 700 android box. Works great WHEN it's working.What I mean is that now and again the red light simply won't click on to blue? I've tried switching it off and on and disconnecting it, reconnecting it... over and over again. After a day or so, all of a sudden, poof it comes on blue when connected. I'm ready to throw it out and buy something new. I tried the tools above, but my computer won't recognize the device? Does it need to be plugged in and turned on showing the blue light to work? Thanks!
Thanks for the software and drivers, my device now is alive again.
for those who don't work properly the reset button, I was in the same situation, searching on google reset for RK3128 devices, I find a solution, do a short circuit between 8-9 Pin on NAND chip with the USB connected.
Install the drivers attached at the link from djmaj0, flash the update image with Android Tools, and now working perfectly.
PD: i flashed with Win10 x64 and no problems, don't need W7 or W8
Thanks again djmaj0!
After flash
After the flash, is the Android still 4.4.1? or updated to 5.0 or higher?
I have emish x700. However unable to identify the toothpick hole as no click on/off apparent. Im assuming the hole on back between the usb ports. Can you confirm this or where it is. My device is frozen on the emish screen and will not proceed further. Thanks
Icarium20 said:
I have emish x700. However unable to identify the toothpick hole as no click on/off apparent. Im assuming the hole on back between the usb ports. Can you confirm this or where it is. My device is frozen on the emish screen and will not proceed further. Thanks
Click to expand...
Click to collapse
Yes you're right. The reset button is hidden in hole between 2 USB ports.
buytick said:
After the flash, is the Android still 4.4.1? or updated to 5.0 or higher?
Click to expand...
Click to collapse
Hi. After flashing kitkat will remain as the rom is almost same as original. Unfortunately its not pre-rooted, but i have done it with kingroot app after flashing.
djmaj0 said:
Yes you're right. The reset button is hidden in hole between 2 USB ports.
Click to expand...
Click to collapse
.
Thanks Djamjo
On my device unable to feel any pin through that hole. Saw posts elsewhere that you can use the on/off switch and volume control. Do you / any one know about this, also hole underneath the box whick on left out of line to other holes??.
Have downloaded the files. Can you confirm unpacking is same as extracting or unzipping ?. And as havent got to instructions yet do I need to copy the files to a usb or do everything from the laptop.
What is a short circuit between 8/9 pins on nand chip as advised above, and roughly how one would one do it.?
Sorry this is all a learning curve, hence delay. Thanks
For flashing firmware is required the DC-IN 5V to be connected?
So I found out that we have to connect the box with USB3. But in the flash process I get the errore Download IDB Fail. Anyone had this?
I know it's an old post, I successfully upgraded my emish x700 who had power on issues, now I see two types of memory partitions, phone about 1GB and internal_sd about 6GB. Why? Before upgrade I remember I had only one memory (think so) and I didn't have full memory issues when installing new apps. Who can help me?

R1 QFIL Firmware Roms

rom.gizchina.it/upload/R1/R1_user_V6.0.0.rar
rom.gizchina.it/upload/R1/R1_user_V6.0.4.rar
rom.gizchina.it/upload/R1/R1_user_V6.1.0.rar
rom.gizchina.it/upload/R1/R1_user_V6.6.0_TNT.rar
You must use a EDL CABLE for flash these firmware roms.
Just launch the file edl-flash.bat and wait
I need help to Root this phone !!!
deep cable
I can't buy deep cable, so can you show me how to make it?
QTeknology said:
rom.gizchina.it/upload/R1/R1_user_V6.0.0.rar
rom.gizchina.it/upload/R1/R1_user_V6.0.4.rar
rom.gizchina.it/upload/R1/R1_user_V6.1.0.rar
rom.gizchina.it/upload/R1/R1_user_V6.6.0_TNT.rar
You must use a EDL CABLE for flash these firmware roms.
Just launch the file edl-flash.bat and wait
I need help to Root this phone !!!
Click to expand...
Click to collapse
It's already rooted.
mofazar said:
I can't buy deep cable, so can you show me how to make it?[/QUOTE
Very easy indeed, just put a switch between "black" and "green" wires on a standard USB cable. If you don't have a switch (I got mine from an old PC case) you can touch black and green together by hand.
Click to expand...
Click to collapse
I need rom qfil smartisan nut pro2s
can anybody help me? I need qfil rom for smartisan nut pro 2s
I need smartisan u2 pro firmware too help please
Please help me with firmware
R1_user_V6.6.0_TNT.rar
Stuck on boot logo after edl-flash.bat
How to fix? =(

x96 mini - solid red light, undetectable.. Help please.

Purchased new box and was stuck on x96 mini page from start. I pressed pin and powered back up (without sd card in box) to try and get to menu to just simply reboot it but solid red light came on without me even getting to menu that I know of. I have tried all methods found in these forums. For grounding out pins I read that some people successful after trying different pins then in posts but they not post pins they used, may be helpful to others if they did. I don't think world cup drivers works for Windows 10, or I need help making them work as I tried connecting a working box to usb burning tool and was also not recognized but windows itself recognized. Windows does not recognise my bricked box. Any help would be greatly appreciated.
coyotecal said:
Purchased new box and was stuck on x96 mini page from start. I pressed pin and powered back up (without sd card in box) to try and get to menu to just simply reboot it but solid red light came on without me even getting to menu that I know of. I have tried all methods found in these forums. For grounding out pins I read that some people successful after trying different pins then in posts but they not post pins they used, may be helpful to others if they did. I don't think world cup drivers works for Windows 10, or I need help making them work as I tried connecting a working box to usb burning tool and was also not recognized but windows itself recognized. Windows does not recognise my bricked box. Any help would be greatly appreciated.
Click to expand...
Click to collapse
https://www.youtube.com/watch?v=fsyS3p5asZs&list=LLxxDotaUFh_I_kB85QpA6Gw&index=2&t=0s
Neekapp said:
https://www.youtube.com/watch?v=fsyS3p5asZs&list=LLxxDotaUFh_I_kB85QpA6Gw&index=2&t=0s
Click to expand...
Click to collapse
That is for x96, not x96 mini...different board.
coyotecal said:
That is for x96, not x96 mini...different board.
Click to expand...
Click to collapse
Just have a look at this:
https://blog.danman.eu/bricking-and-unbricking-vontar-x96-mini/
hi. was this ever solved? were you able to fix your x96 mini?
@claishem
https://blog.danman.eu/bricking-and-unbricking-vontar-x96-mini/
It will Unbrick your X96mini
zusatzmetall said:
@claishem
https://blog.danman.eu/bricking-and-...ntar-x96-mini/
It will Unbrick your X96mini
---------- Post added at 10:25 AM ---------- Previous post was at 10:25 AM ----------
[/COLOR @claishem
https://blog.danman.eu/bricking-and-...ntar-x96-mini/
It will Unbrick your X96mini
Click to expand...
Click to collapse
this is what appears in the link you provided sir
https://blog.danman.eu/bricking-and-unbricking-vontar-x96-mini/
zusatzmetall said:
@claishem
https://blog.danman.eu/bricking-and-...ntar-x96-mini/
It will Unbrick your X96mini
Click to expand...
Click to collapse
@zusatzmetall
or you are referring to the shorting of pins sir?
but i have seen a lot of reports here and and in other forums that they still were not able to fix their x96 minis even if they did the tutorial of danman. any idea?
Trust me, it works
zusatzmetall said:
Trust me, it works
Click to expand...
Click to collapse
thanks for the assurance sir. i really hope so. i had a mibox 3 last year. it also uses amlogic processor, s905x. i was able to play with its os for a few months until i bricked it while trying to downgrade it succesfuly from oreo despite of the warning not to do it. because mibox has this kind of like anti rollback protection that would render your device paperweight if you downgrade. there was one expert also from vietnam named Nguyen Van Dai if you are also familiar with him, who was the author of the modified bootloader of mibox to be able to safely downgrade from Nougat to marshmallow. but when i tried his modified oreo bootloader i bricked my mibox and that's the end of the box.
anyway, what is important to me now is a sure answer if this x96 mini can be revived regardless of anykind of software brick.
---------- Post added at 04:30 PM ---------- Previous post was at 03:47 PM ----------
zusatzmetall said:
Trust me, it works
Click to expand...
Click to collapse
by the way sir, have you already encountered yourself that red light only problem and then you were able to resolve using the method of danman? most or all of those who are saying that danman method does not work for them are those whose boxes only show red light..
It works!!!
So guys. I found a new way to recover our bricked X96 Minis. So I bricked mine with a wrong FW. I had inly red light, no reset through AV switch, no magic SD card, Computer doesn t recognized usw.
First of all: I have a X96 mini with Amilogic S905W CPU, 2/16. My PCB version is x96 Mini Q6X v 2.2 17355 and I have memory from Samsung. They call it k4b4g0446q.
So the method:
1. Short the two point.
2. Connect USB Kabel to PC. Wait until the computer recognize the box.
3. Remove shortcut, connect AC adapter to the box.
4. Flash enjoy
I used a laptop with Windows 7 64 bit and USB Burning tool 2.2.0. The USB 3 kabel is one meter long. I flashed simply an android 9 FW from web.
Q6X v2.3 1/8GB X96 mini
Hi,
Do you have any clues for Q6x v2.3 board X96 mini 1/8gb board? I tried as card flash but after 2s afters flashing started the box turn off itself and of i try to connect box to pc, windows says usb device not recognised and goes to coonect/disconnect loop.
Eh nevermind, i changed usb cable. Pc recognised it, flashed. But sometime freeze itself :/
Kuontol tenan juancokkk frimware tipu led red mulu asuuu juanccokkk anjing wedhuss
Hello,
I had exactly the same problem on my x96mini.
You must have a cable that turns on the red led without the charger, my first cable did not do it I had to change it.
I connect the cable to my pc.
Took out the motherboard, I turned it over.
With a metal object I rubbed it on all the welds (by despair)
By magic I saw Connect succes posted on Burning tool.
Good luck if you have this problem
claishem said:
this is what appears in the link you provided sir
Click to expand...
Click to collapse
I have x88 pro stuck on red light not recognized by pc or tv any help please
I have X96 mini with Q6X V2.3 18186 16/2GB board. I flashed a new firmware in it and it was working fine for one day then it suddenly stopped and now when i plug it in red light stays solid for few seconds then start blinking, it in not turning on or detected by computer. How to fix this.

Categories

Resources