I was using lrteam twrp 3.4.2b-1206 and I was sideloading the vendor update for 12.2.1.0 when the progress bar froze. I gave it 10 minutes and held the power button to reboot and now the phone is showing no signs of life i cant get it to even show the poco screen. I've got no ideas left on what to do.
ashawanz said:
I was using lrteam twrp 3.4.2b-1206 and I was sideloading the vendor update for 12.2.1.0 when the progress bar froze. I gave it 10 minutes and held the power button to reboot and now the phone is showing no signs of life i cant get it to even show the poco screen. I've got no ideas left on what to do.
Click to expand...
Click to collapse
Did you try holding power and volume down? Also charge it for some hours.
Tecardo said:
Did you try holding power and volume down? Also charge it for some hours.
Click to expand...
Click to collapse
yeah no combination of buttons will show any signs of life and i can't even get to the bootloader. It should be at 100% battery at this point i dont think that's the issue either
Where did you find vendor update for 12.2.1.0 ?
NOSS8 said:
Where did you find vendor update for 12.2.1.0 ?
Click to expand...
Click to collapse
Some users postet from Xiaomi firmware website (non official) . Link is in many rom threads
ashawanz said:
yeah no combination of buttons will show any signs of life and i can't even get to the bootloader. It should be at 100% battery at this point i dont think that's the issue either
Click to expand...
Click to collapse
Did you attach it to pc and see what device gets detected then? It could be in qualcomm usb mode
Tecardo said:
Some users postet from Xiaomi firmware website (non official) . Link is in many rom threads
Click to expand...
Click to collapse
Firmeware not vendor,not the same.
is the phone appear on pc?
Tecardo said:
Did you attach it to pc and see what device gets detected then? It could be in qualcomm usb mode
Click to expand...
Click to collapse
If the the phone appear in qualcom usb, flashing in EDL will be possible and requires an authorization that only official repairers have.
NOSS8 said:
Firmeware not vendor,not the same.
is the phone appear on pc?
Click to expand...
Click to collapse
as I remember it's included? Otherwise use Xiaomi eu rom. It's including vendor.
Tecardo said:
as I remember it's included? Otherwise use Xiaomi eu rom. It's including vendor.
Click to expand...
Click to collapse
My first question was for ashawanz" Where did you find vendor update for 12.2.1.0 ? "
and this answer" If the the phone appear in qualcom usb, flashing in EDL will be possible and requires an authorization that only official repairers have" was not intended for you 'my mistake' but still for ashawanz
ashawanz said:
yeah no combination of buttons will show any signs of life and i can't even get to the bootloader. It should be at 100% battery at this point i dont think that's the issue either
Click to expand...
Click to collapse
Where did you find vendor update for 12.2.1.0 ?
Firmeware not vendor,not the same.
is the phone appear on pc?
If the the phone appear in qualcom usb, flashing in EDL will be possible and requires an authorization that only official repairers have.
Tecardo said:
Did you attach it to pc and see what device gets detected then? It could be in qualcomm usb mode
Click to expand...
Click to collapse
So I just took the device apart to try and get into qualcomm edl mode through hardware and now the front camera led turns red while charging. apart from that there are no signs of life though it won't show up in my pc's device manager even though I have the qualcomm drivers
ashawanz said:
So I just took the device apart to try and get into qualcomm edl mode through hardware and now the front camera led turns red while charging. apart from that there are no signs of life though it won't show up in my pc's device manager even though I have the qualcomm drivers
Click to expand...
Click to collapse
So you should let it charge till later in 6h
NOSS8 said:
Where did you find vendor update for 12.2.1.0 ?
Firmeware not vendor,not the same.
is the phone appear on pc?
If the the phone appear in qualcom usb, flashing in EDL will be possible and requires an authorization that only official repairers have.
Click to expand...
Click to collapse
Phone does not appear on pc and I got it from the evoX 5.1 thread. Ive flashed it before however and it didn't do this it worked just fine
ashawanz said:
Phone does not appear on pc and I got it from the evoX 5.1 thread. Ive flashed it before however and it didn't do this it worked just fine
Click to expand...
Click to collapse
This is the correct firmware.
What do you want to do in EDL mode?
NOSS8 said:
This is the correct firmware.
What do you want to do in EDL mode?
Click to expand...
Click to collapse
It's not booting, he doesn't want to get into edl. It's showing no reaction. But he could try pressing power button for 1min and look for vibration
To try to restore the phone yourself, you must use commands in fastboot or adb.
Tecardo said:
It's not booting, he doesn't want to get into edl. It's showing no reaction. But he could try pressing power button for 1min and look for vibration
Click to expand...
Click to collapse
the power button for a minute didnt do anything either sadly. Im trying to get into edl so i can try and recover it with QPST, but even after opening the phone up and trying to get into edl through hardware, i was only able to get the red charging light to start showing whilst charging. Should I try to disconnect and reconnect the battery maybe?
ashawanz said:
the power button for a minute didnt do anything either sadly. Im trying to get into edl so i can try and recover it with QPST, but even after opening the phone up and trying to get into edl through hardware, i was only able to get the red charging light to start showing whilst charging. Should I try to disconnect and reconnect the battery maybe?
Click to expand...
Click to collapse
Yep, can't hurt at this point.
You can try this:
Recharge the battery for at least 1 hour (even if you think it is already charged)
after connect it by usb and press the power button first,power button with volume -, button with volume +, and try to see if it appears on the pc and in what way.
Related
Hi gang,
My Xperia Z5 (E6603) would not boot up after the latest update. I'm guessing it must've died during the update.
I tried:
Reset (Pwr + Vol+/-) and OFF button in sim card tray. All reset attempt was done several times with and without the simcard tray.
I noticed the phone did not vibrate when I tried Pwr + vol+ or with the OFF button by itself. It only vibrate when the OFF and Pwr button were held down simultaneously.
To rule out it was battery, I let it charged for almost 2 days now without any success. I still get the slow blinking red light and no solid red or orange or green light indicating the device is fully charged. I also check the integrity of the battery at the stored and it is at 4.0 V, so I believe the battery is not the problem.
Unplugging battery method: Tried unplugging the battery and connect to the computer then plugged it back in with no luck.
Flashtool was not recognized after holding Vol- and connect to the computer.
I also tried different charger and usb
i read from many forum that the battery needs to die in order to reset the kernel. Should I just let the battery discharged? Or are there others ways that are more efficient?
I'm not sure what to do at this point. Any suggestion will be greatly appreciated.
Thank you!
try change battery
Alvian_P said:
try change battery
Click to expand...
Click to collapse
I believe the battery is ok. I brought it to the store to check the charge and it was sufficient
thank you,
Flash phone using Flashtool.
El Solido said:
Flash phone using Flashtool.
Click to expand...
Click to collapse
Unfortunately, the phone is not recognized by flashtool.
Thank you,
maybe bootloader corrupt. bootloader in emmc. try bring your phone to phone services, JTAG flash may help.
Alvian_P said:
maybe bootloader corrupt. bootloader in emmc. try bring your phone to phone services, JTAG flash may help.
Click to expand...
Click to collapse
What software can I use to fix the bootloader? I have an unlocked phone so my service provider will not take care of it.
Thank you!
myphonedied said:
What software can I use to fix the bootloader? I have an unlocked phone so my service provider will not take care of it.
Thank you!
Click to expand...
Click to collapse
Go to phone repair outlets in your city, not in Sony Service Center. usually they can fix hardware problem. I dont know what software are used. I only know with Jtag can repair bootloader via test point.
Alvian_P said:
Go to phone repair outlets in your city, not in Sony Service Center. usually they can fix hardware problem. I dont know what software are used. I only know with Jtag can repair bootloader via test point.
Click to expand...
Click to collapse
Does the bootloader need to be unlocked on the phone previously for the JTAG method to work?
Thank you for the suggestion,
myphonedied said:
Does the bootloader need to be unlocked on the phone previously for the JTAG method to work?
Thank you for the suggestion,
Click to expand...
Click to collapse
not sure. locked or unlocked should work, because the files inject directly to emmc
by the way, have you try to change another battery?
ave you tried to boot the phone into download mode?
Have you tried the actual Sony Tool and the Recovery-Process?
With that i unbricked my Z5 from that symptons i think 2 or 3 times already after the flash went somehow wrong because it stopped midway.
Alvian_P said:
not sure. locked or unlocked should work, because the files inject directly to emmc
by the way, have you try to change another battery?
Click to expand...
Click to collapse
I ordered a new battery, will try that and let you know
Thanks!
Seelbreaker said:
ave you tried to boot the phone into download mode?
Have you tried the actual Sony Tool and the Recovery-Process?
With that i unbricked my Z5 from that symptons i think 2 or 3 times already after the flash went somehow wrong because it stopped midway.
Click to expand...
Click to collapse
The phone won't boot into download mode. It's not recognized by PC companion so I can't carry out the recovery process.
Thank you for the suggestion!
myphonedied said:
I ordered a new battery, will try that and let you know
Thanks!
Click to expand...
Click to collapse
Ok... :good:
myphonedied said:
The phone won't boot into download mode. It's not recognized by PC companion so I can't carry out the recovery process.
Thank you for the suggestion!
Click to expand...
Click to collapse
Another thing - on my Laptop i can't access fastboot mode because it restarts everytime (showing the blue led and then it reboots), therefore i have to attach the Z5 to the Dockingstation.
But it seems like it is completeley dead right?
just to be sure - press and hold vol up and then connect your usb-cable. If the LED stays blue - gg
Then you just have to install the fastboot driver in Test-Mode (reboot to f8 and deactivate the Enforced Driver Signature) and then you may be able to atleast flash or better first boot the phone with a new kernel. If the boot works and then crashes you have your first step to unbrick the phone.
fastboot boot "kernel-image"
Altough i don't have any idea which Kernel you should choose
Seelbreaker said:
Another thing - on my Laptop i can't access fastboot mode because it restarts everytime (showing the blue led and then it reboots), therefore i have to attach the Z5 to the Dockingstation.
But it seems like it is completeley dead right?
just to be sure - press and hold vol up and then connect your usb-cable. If the LED stays blue - gg
Then you just have to install the fastboot driver in Test-Mode (reboot to f8 and deactivate the Enforced Driver Signature) and then you may be able to atleast flash or better first boot the phone with a new kernel. If the boot works and then crashes you have your first step to unbrick the phone.
fastboot boot "kernel-image"
Altough i don't have any idea which Kernel you should choose
Click to expand...
Click to collapse
Red blinking red in Sony phones mean bricked motherboard
Try on different computer. Use USB 2.0 port and original sony cable.
EugenStanis said:
Red blinking red in Sony phones mean bricked motherboard
Click to expand...
Click to collapse
Any way to fix a bricked motherboard?
myphonedied said:
Any way to fix a bricked motherboard?
Click to expand...
Click to collapse
Yes, replacing it
Use setool2 box for unbreak your phone
so, i flashed lineage in dualboot on oreo firmware and my phone went completely dead, no download no vibration no response to anything i do to it. i just wanted to ask this question here too, is there any way this device could be brought back to life?
byseby said:
so, i flashed lineage in dualboot on oreo firmware and my phone went completely dead, no download no vibration no response to anything i do to it. i just wanted to ask this question here too, is there any way this device could be brought back to life?
Click to expand...
Click to collapse
When you plug in USB cable does indicator show red?
Try connect to PC what its showing on device manager?
afaneh92 said:
When you plug in USB cable does indicator show red?
Try connect to PC what its showing on device manager?
Click to expand...
Click to collapse
nope, no led, no sound from pc, nothing on device manager, odin says nothing smartswitch nothing, plugging it in does nothing otg in and no power supplied to the attached device
byseby said:
nope, no led, no sound from pc, nothing on device manager, odin says nothing smartswitch nothing, plugging it in does nothing otg in and no power supplied to the attached device
Click to expand...
Click to collapse
Try hold on volume up and down and power button at the same time for 30 second I think its kernel panic.
Also leave phone charging for a few hours and don't touch it see if it also was a bit low battery.
lynxblaine said:
Also leave phone charging for a few hours and don't touch it see if it also was a bit low battery.
Click to expand...
Click to collapse
none of it works, left it overnight and tried every button combo
Power + Volume Down for 10-15 second simulates a battery removal, so try that.
the_scotsman said:
Power + Volume Down for 10-15 second simulates a battery removal, so try that.
Click to expand...
Click to collapse
as i said, i tried every button combo there is to try
byseby said:
as i said, i tried every button combo there is to try
Click to expand...
Click to collapse
Given it's not responding to that, and no lights when plugged into power, I'd say it's probably hard bricked and unrecovaerable. That's the risk when playing with things like dual boot etc I guess. Or just bad luck.
byseby said:
so, i flashed lineage in dualboot on oreo firmware and my phone went completely dead, no download no vibration no response to anything i do to it. i just wanted to ask this question here too, is there any way this device could be brought back to life?
Click to expand...
Click to collapse
I just had the same issue, how did you fix it?
sethchrome45 said:
I just had the same issue, how did you fix it?
Click to expand...
Click to collapse
I opened mine up
I was just thinking about trying Dual Boot ?️.
I bought my phone from Aliexpress and is tencent version flashed with global. After opening and setting it up, it was working fine and started playing pubg. After about 1 hour, it just died. No warning or anything, just ploof.
It doesn't respond to anything, power, volume +, volume -. Nothing when it's not charging.
But When I plug it into its charger, it does a boot loop.
When charging on the side, it boots up the android logo then the ROG logo but dies right after.
When charging on the bottom, it flashes the android logo and dies.
While it does that I held the volume up button, I can access fastboot and it stays on with the options:
- Start
- Restart bootloader
- Recovery mode
- Power off
I tried every option to no avail.
When I plug out the charger while in fastboot, it dies.
I think the battery connection is fried.
Why dont you flash a Firmware through edl and give a try. If battery doesnt hold up after unplugged even after flashing new firmware then its a hardware problem mostly. There is a thread regarding flashing through edl. Check it out
jhosharath said:
Why dont you flash a Firmware through edl and give a try. If battery doesnt hold up after unplugged even after flashing new firmware then its a hardware problem mostly. There is a thread regarding flashing through edl. Check it out
Click to expand...
Click to collapse
I tried but my laptop can't detect my phone. Can you send driver please if you have.
That Mi flash tool only has the necessary drivers. I had it installed from it long time back. I dont have specific drivers. Maybe you can do a search for qualcomm or 9008 USB drivers. Or you can try in another pc.
Make sure you turn off the phone either from bootloader or manually. Then while pressing volume up plug into pc and check.
jhosharath said:
That Mi flash tool only has the necessary drivers. I had it installed from it long time back. I dont have specific drivers. Maybe you can do a search for qualcomm or 9008 USB drivers. Or you can try in another pc.
Make sure you turn off the phone either from bootloader or manually. Then while pressing volume up plug into pc and check.
Click to expand...
Click to collapse
My phone has no life when unplugged.
jhosharath said:
That Mi flash tool only has the necessary drivers. I had it installed from it long time back. I dont have specific drivers. Maybe you can do a search for qualcomm or 9008 USB drivers. Or you can try in another pc.
Make sure you turn off the phone either from bootloader or manually. Then while pressing volume up plug into pc and check.
Click to expand...
Click to collapse
I tried to download from mi flash but it didn't work.
I tried the flash raw with the WW version for ROG5 and no difference just the same brick phone unfortunately.
mikeychsia said:
I tried the flash raw with the WW version for ROG5 and no difference just the same brick phone unfortunately.
Click to expand...
Click to collapse
Did the flash go through?
I would suggest to flash a CN version while being on bootloader.
Use the side usb port, and make sure to use a good cable.
mikeychsia said:
I tried the flash raw with the WW version for ROG5 and no difference just the same brick phone unfortunately.
Click to expand...
Click to collapse
RAW Firmware Collection and Guide
All fastboot / adb commands require using the side USB-C port https://developer.android.com/studio/releases/platform-tools.html#download Make sure you have fastboot installed Add platform tools to PATH (post 2) Make a backup of anything...
forum.xda-developers.com
Charging is handled by the firmware. If the firmware breaks, it seems to disable charging. It may be partially because the battery is split. Either way, a full restore seems to fix the problem.
JazonX said:
Did the flash go through?
I would suggest to flash a CN version while being on bootloader.
Use the side usb port, and make sure to use a good cable.
Click to expand...
Click to collapse
The flash went through and yes I tried a CN version and still same result I go back to that same waiting to flash ram dump screen
JazonX said:
Did the flash go through?
I would suggest to flash a CN version while being on bootloader.
Use the side usb port, and make sure to use a good cable.
Click to expand...
Click to collapse
The flash went through all and I tried both the CN version and the WW version and nothing happened. Still the same result the waiting for flash dump ram still comes back out .
i dont know why but my phone for some reason stopped working while being on my table, it didnt boot up or vibrate also it didnt show anything on the display.
elosanta said:
i dont know why but my phone for some reason stopped working while being on my table, it didnt boot up or vibrate also it didnt show anything on the display.
Click to expand...
Click to collapse
If you plug it into your computer, does it show up in Device Manager as anything?
Have you tried holding down the power button for 10 seconds?
V0latyle said:
If you plug it into your computer, does it show up in Device Manager as anything?
Have you tried holding down the power button for 10 seconds?
Click to expand...
Click to collapse
neither of those work.
elosanta said:
neither of those work.
Click to expand...
Click to collapse
I'm afraid your device is bricked, and the only thing you can do is take it to a repair shop.
Have you tried booting in download mode?
Yosoygodot said:
Have you tried booting in download mode?
Click to expand...
Click to collapse
yes, it dosent show like anything on the display when booting to download mode
Check if odin recognises it or if it draws current while charging
Yosoygodot said:
Check if odin recognises it or if it draws current while charging
Click to expand...
Click to collapse
It actually gives power, odin dosent recognize it and also device manager it shows nothing
When I used the Fastboot Enhance tool to flash the payload.bin file, after the flash process finished I try to reboot but unfortunately it was dead.
No Fastboot, no EDL, no recovery, 3 buttons not working, power with up/down not working, when i connect to PC no sound that the pc recognize the phone "OP 8T", when I plug it into charger no info showing, Just black screen.
So it's working now, I'll explain everything here so it might help.
My device is OnePlus 8T DDR5 version
first, I understand what happened to me, I think the tool didn't recognize ram type automatically so it was flash DDR4 on a DDR5 device, so it made a hard brick
at this point, the idea is to connect 2 test points, and you can force your phone to enter to EDL mode, and we can do it in two ways:
1. Rootk1t giude, thax bro Rootk1t
- Removing the back panel by heating it.
- Unplugging battery
- Then use the EDL points on the motherboard to force the device to boot EDL.
- The device immediately will be recognised with just one tap on "enum" now.
- Plugging the battery again and attaching the back panel and rebooting
2. By using deep EDL cable, but not any edl cable, it must be a moded cable so it can be worked with the new security ...... this link will explain
Hydra Tool Gift Xiaomi, Huawei, Redmi Qualcomm EDL Mode New V2 Cable!! - GSM-Forum
Hydra Tool Gift Xiaomi, Huawei, Redmi Qualcomm EDL Mode New V2 Cable!! Hydra Tool New Type-C EDL cable Schematic With this cable you can reboot your
forum.gsmhosting.com
- So i use Hydra EDL Cble V2 , you can buy it from aliexpress
- Be ready and open your MSM tool
- Press the cable button before connecting
- Connect the cable to your phone when you still pressing the button
- Then connect the USB to your PC
- It will automatically put your phone in EDL mode
- Now your phone will show in the MSM tool screen so you can revive it.
Thanks to everyone who tried to help.
Special thanks to Rootk1t , semdoc
Abdo Ismail said:
when I used the Fastboot Enhance tool to flash the payload.bin file, after the flash process finished I try to reboot but unfortunately it was dead.
No Fastboot, no EDL, no recovery, 3 buttons not working, power with up/down not working, when i connect to PC no sound that the pc recognize the phone "OP 8T", when I plug it into charger no info showing, Just black screen.
I don't know what should i do, please anyone help me with this problem.
Thanks in advance
Click to expand...
Click to collapse
Are you sure no EDL? Did you try the msm tool to restore to factory settings?
JedidroidX said:
Are you sure no EDL? Did you try the msm tool to restore to factory settings?
Click to expand...
Click to collapse
I'm sure, and I try MSM , the phone can't connect anymore to PC
Abdo Ismail said:
I'm sure, and I try MSM , the phone can't connect anymore to PC
Click to expand...
Click to collapse
Seem like you flashed the wrong xml for the ram type. There is one for ddr4 and ddr5. If EDL is not working I'm afraid according to several post it's an unrecoverable brick...sorry mate!!!
However keep searching for a solution, you never know maybe a new method of recovery from this disaster may exist. I'll keep searching and if I find anything I'll post it here!
Also have you tried the 3 buttons connected from charger and disconnected? Usually for some reason my phone won't respond with the 3 buttons when connected to usb sometimes.
Also have you used the msm tool before?
JedidroidX said:
Seem like you flashed the wrong xml for the ram type. There is one for ddr4 and ddr5. If EDL is not working I'm afraid according to several post it's an unrecoverable brick...sorry mate!!!
However keep searching for a solution, you never know maybe a new method of recovery from this disaster may exist. I'll keep searching and if I find anything I'll post it here!
Also have you tried the 3 buttons connected from charger and disconnected? Usually for some reason my phone won't respond with the 3 buttons when connected to usb sometimes.
Also have you used the msm tool before?
Click to expand...
Click to collapse
Thanks bro for your cooperation, yes i tried everything and yes i used MSM tool a lot of time.
i'll searh more to fix this prob, thx again
Abdo Ismail said:
Thanks bro for your cooperation, yes i tried everything and yes i used MSM tool a lot of time.
i'll searh more to fix this prob, thx again
Click to expand...
Click to collapse
Just one more thing, when you connect the phone to pc check your device manager to see if the PC reads the phone. If it does than its just a driver issue and reinstalling the qualcom driver for msm maybe needed.
I've found that sometimes I have to reinstall the Qualcomm drivers for EDL. So check that when you connect the phone to the PC in EDL mode there isn't an entry in Device Manager under Ports (COM & LPT)
JedidroidX said:
Just one more thing, when you connect the phone to pc check your device manager to see if the PC reads the phone. If it does than its just a driver issue and reinstalling the qualcom driver for msm maybe needed.
Click to expand...
Click to collapse
when I connect it to PC I can't hear the sound which appears when you connect a new device, and also no changes in the device manager unfortunately
BillGoss said:
I've found that sometimes I have to reinstall the Qualcomm drivers for EDL. So check that when you connect the phone to the PC in EDL mode there isn't an entry in Device Manager under Ports (COM & LPT)
Click to expand...
Click to collapse
I can't know which mode the phone is stuck on, because I have only a black screen, even the Power button with volume up / down not working,
do you think if I keep it for a couple of days the battery will drain and I can use MSM tool with press 2 volume buttons, it's the last thing i think about
Abdo Ismail said:
I can't know which mode the phone is stuck on, because I have only a black screen, even the Power button with volume up / down not working,
do you think if I keep it for a couple of days the battery will drain and I can use MSM tool with press 2 volume buttons, it's the last thing i think about
Click to expand...
Click to collapse
I would open it up and remove the battery instead of waiting for days but that's also an option. It's not that hard to open, I opened mines to replace the usb port. I just held the back of the bottom corners of the phone over the stove until it was hot enough to soften the glue and used an old credit card and my thumb nail to open it. It maybe unrecoverable anyway so its worth a try.
JedidroidX said:
I would open it up and remove the battery instead of waiting for days but that's also an option. It's not that hard to open, I opened mines to replace the usb port. I just held the back of the bottom corners of the phone over the stove until it was hot enough to soften the glue and used an old credit card and my thumb nail to open it. It maybe unrecoverable anyway so its worth a try.
Click to expand...
Click to collapse
yes, I thought to do that, so I keep it to be the last option, I'm still searching for any new ideas.
bro, really I want to thank you for supporting me, I appreciate that
Abdo Ismail said:
I can't know which mode the phone is stuck on, because I have only a black screen, even the Power button with volume up / down not working,
do you think if I keep it for a couple of days the battery will drain and I can use MSM tool with press 2 volume buttons, it's the last thing i think about
Click to expand...
Click to collapse
I've had a totally black screen at times in Qualcomm Crashdump Mode. To get out of it you can use Power+Vol up and then, when the phone buzzes, use the key combination for bootloader or MSM.
BillGoss said:
I've had a totally black screen at times in Qualcomm Crashdump Mode. To get out of it you can use Power+Vol up and then, when the phone buzzes, use the key combination for bootloader or MSM.
Click to expand...
Click to collapse
I tried a lot to press Volume Up + Power & Volume Down + Power & the 3 buttons, but with no response.
I can't feel any buzz, even I tried it when the phone connected to the PC, no sound come from PC prove that the phone is connected
Please keep us updated with any current queries or resolution as I'm very interested in the outcome.
Thank you!
Abdo Ismail said:
when I used the Fastboot Enhance tool to flash the payload.bin file, after the flash process finished I try to reboot but unfortunately it was dead.
No Fastboot, no EDL, no recovery, 3 buttons not working, power with up/down not working, when i connect to PC no sound that the pc recognize the phone "OP 8T", when I plug it into charger no info showing, Just black screen.
I don't know what should i do, please anyone help me with this problem.
Thanks in advance
Click to expand...
Click to collapse
Hello!
If waiting for battery to discharge will not help you, i suggest of:
- Removing the back panel by heating it.
- Unplugging battery
- Then using the EDL points on the motherboard to force the device to boot EDL.
-The device immediately will be recognised by just one tap on "enum" now.
- Plugging the battery again and attaching back panel and rebooting.
JedidroidX said:
Please keep us updated with any current queries or resolution as I'm very interested in the outcome.
Thank you!
Click to expand...
Click to collapse
sure my bro
Rootk1t said:
Hello!
If waiting for battery to discharge will not help you, i suggest of:
- Removing the back panel by heating it.
- Unplugging battery
- Then using the EDL points on the motherboard to force the device to boot EDL.
-The device immediately will be recognised by just one tap on "enum" now.
- Plugging the battery again and attaching back panel and rebooting.
Click to expand...
Click to collapse
thanks my friend for your suggestion, yes I was thinking about this solution, but I keep it to be the last one, I think I will try this method at the weekend as I'm busy with work these days.
I'll tell you after I try this solution.
Thanks for your cooperation
JedidroidX said:
Seem like you flashed the wrong xml for the ram type. There is one for ddr4 and ddr5.
Click to expand...
Click to collapse
I have the same problem now after trying to downgrade to OOS12
I used this, EU version, I cant find another version, which would have been the right one?
https://oxygenos.oneplus.net/4668_sign_KB2003_11_C_OTA_1360_all_86c2c1_01000100.zip
It installed, but now I cant start the ohone in any way.
Any tipps? Did it work for you Abdo Ismail?
SamNeuer said:
I have the same problem now after trying to downgrade to OOS12
I used this, EU version, I cant find another version, which would have been the right one?
https://oxygenos.oneplus.net/4668_sign_KB2003_11_C_OTA_1360_all_86c2c1_01000100.zip
It installed, but now I cant start the ohone in any way.
Any tipps? Did it work for you Abdo Ismail?
Click to expand...
Click to collapse
Similar case
[OP8T][OOS KB05AA/BA/DA] Unbrick tool to restore your device to OxygenOS
Disclaimer: By attempting any of the processes listed in this thread you accept full responsibility for your actions. I will not be held responsible if your device stops working, catches fire, or turns into a hipster and claims to have been...
forum.xda-developers.com
Rootk1t said:
Hello!
If waiting for battery to discharge will not help you, i suggest of:
- Removing the back panel by heating it.
- Unplugging battery
- Then using the EDL points on the motherboard to force the device to boot EDL.
-The device immediately will be recognised by just one tap on "enum" now.
- Plugging the battery again and attaching back panel and rebooting.
Click to expand...
Click to collapse
Thank you so much for this, after spending 16$ on a stupid edl cable that never worked, your guide revived my op8t I appreciate you!