Hi gang,
My Xperia Z5 (E6603) would not boot up after the latest update. I'm guessing it must've died during the update.
I tried:
Reset (Pwr + Vol+/-) and OFF button in sim card tray. All reset attempt was done several times with and without the simcard tray.
I noticed the phone did not vibrate when I tried Pwr + vol+ or with the OFF button by itself. It only vibrate when the OFF and Pwr button were held down simultaneously.
To rule out it was battery, I let it charged for almost 2 days now without any success. I still get the slow blinking red light and no solid red or orange or green light indicating the device is fully charged. I also check the integrity of the battery at the stored and it is at 4.0 V, so I believe the battery is not the problem.
Unplugging battery method: Tried unplugging the battery and connect to the computer then plugged it back in with no luck.
Flashtool was not recognized after holding Vol- and connect to the computer.
I also tried different charger and usb
i read from many forum that the battery needs to die in order to reset the kernel. Should I just let the battery discharged? Or are there others ways that are more efficient?
I'm not sure what to do at this point. Any suggestion will be greatly appreciated.
Thank you!
try change battery
Alvian_P said:
try change battery
Click to expand...
Click to collapse
I believe the battery is ok. I brought it to the store to check the charge and it was sufficient
thank you,
Flash phone using Flashtool.
El Solido said:
Flash phone using Flashtool.
Click to expand...
Click to collapse
Unfortunately, the phone is not recognized by flashtool.
Thank you,
maybe bootloader corrupt. bootloader in emmc. try bring your phone to phone services, JTAG flash may help.
Alvian_P said:
maybe bootloader corrupt. bootloader in emmc. try bring your phone to phone services, JTAG flash may help.
Click to expand...
Click to collapse
What software can I use to fix the bootloader? I have an unlocked phone so my service provider will not take care of it.
Thank you!
myphonedied said:
What software can I use to fix the bootloader? I have an unlocked phone so my service provider will not take care of it.
Thank you!
Click to expand...
Click to collapse
Go to phone repair outlets in your city, not in Sony Service Center. usually they can fix hardware problem. I dont know what software are used. I only know with Jtag can repair bootloader via test point.
Alvian_P said:
Go to phone repair outlets in your city, not in Sony Service Center. usually they can fix hardware problem. I dont know what software are used. I only know with Jtag can repair bootloader via test point.
Click to expand...
Click to collapse
Does the bootloader need to be unlocked on the phone previously for the JTAG method to work?
Thank you for the suggestion,
myphonedied said:
Does the bootloader need to be unlocked on the phone previously for the JTAG method to work?
Thank you for the suggestion,
Click to expand...
Click to collapse
not sure. locked or unlocked should work, because the files inject directly to emmc
by the way, have you try to change another battery?
ave you tried to boot the phone into download mode?
Have you tried the actual Sony Tool and the Recovery-Process?
With that i unbricked my Z5 from that symptons i think 2 or 3 times already after the flash went somehow wrong because it stopped midway.
Alvian_P said:
not sure. locked or unlocked should work, because the files inject directly to emmc
by the way, have you try to change another battery?
Click to expand...
Click to collapse
I ordered a new battery, will try that and let you know
Thanks!
Seelbreaker said:
ave you tried to boot the phone into download mode?
Have you tried the actual Sony Tool and the Recovery-Process?
With that i unbricked my Z5 from that symptons i think 2 or 3 times already after the flash went somehow wrong because it stopped midway.
Click to expand...
Click to collapse
The phone won't boot into download mode. It's not recognized by PC companion so I can't carry out the recovery process.
Thank you for the suggestion!
myphonedied said:
I ordered a new battery, will try that and let you know
Thanks!
Click to expand...
Click to collapse
Ok... :good:
myphonedied said:
The phone won't boot into download mode. It's not recognized by PC companion so I can't carry out the recovery process.
Thank you for the suggestion!
Click to expand...
Click to collapse
Another thing - on my Laptop i can't access fastboot mode because it restarts everytime (showing the blue led and then it reboots), therefore i have to attach the Z5 to the Dockingstation.
But it seems like it is completeley dead right?
just to be sure - press and hold vol up and then connect your usb-cable. If the LED stays blue - gg
Then you just have to install the fastboot driver in Test-Mode (reboot to f8 and deactivate the Enforced Driver Signature) and then you may be able to atleast flash or better first boot the phone with a new kernel. If the boot works and then crashes you have your first step to unbrick the phone.
fastboot boot "kernel-image"
Altough i don't have any idea which Kernel you should choose
Seelbreaker said:
Another thing - on my Laptop i can't access fastboot mode because it restarts everytime (showing the blue led and then it reboots), therefore i have to attach the Z5 to the Dockingstation.
But it seems like it is completeley dead right?
just to be sure - press and hold vol up and then connect your usb-cable. If the LED stays blue - gg
Then you just have to install the fastboot driver in Test-Mode (reboot to f8 and deactivate the Enforced Driver Signature) and then you may be able to atleast flash or better first boot the phone with a new kernel. If the boot works and then crashes you have your first step to unbrick the phone.
fastboot boot "kernel-image"
Altough i don't have any idea which Kernel you should choose
Click to expand...
Click to collapse
Red blinking red in Sony phones mean bricked motherboard
Try on different computer. Use USB 2.0 port and original sony cable.
EugenStanis said:
Red blinking red in Sony phones mean bricked motherboard
Click to expand...
Click to collapse
Any way to fix a bricked motherboard?
myphonedied said:
Any way to fix a bricked motherboard?
Click to expand...
Click to collapse
Yes, replacing it
Use setool2 box for unbreak your phone
Related
Fix Xperia C Red Light brick
Are you facing that the red led on your device blinks and there is no other signs of life? Then you are in the correct thread, I faced this issue when flashing a corrupted recovery but then I found out a easy way to fix it without opening the device or sending it in to Sony.
Requirements:
Xperia C with red light softbrick
MicroUSB Cable
Sony Update Service
Click to expand...
Click to collapse
1. The first thing you need to do is to make sure that you have downloaded Sony Update Service and have installed it onto your PC from the link above, if not, do it now.
2. Now launch Sony Update Service and select Xperia C in the list and then press Next.
3. Hold the Volume Up button and plugin microusbcable while doing so, if that doesn't work for you, hold power + volume up and plugin the microusbcable while doing. Keep holding button combination for a few seconds and wait for a green light on your phone, if it appears check on
your PC so that it's detected.
4. Wait while the firmware is being downloaded and reinstalled on your phone and enjoy your working device!
Have tried this on my bricked xperia c red led
Few weeks back no success
Logic
If you flash wrong recovery there is no way to boot in any mode
I can say this with 100% confident as I had spent full 3 days and tried every thing...
If u wona check goto custome mod for xperia c thred and get recovery installed
Then try this and share results
All the best
chauhanjayc said:
Have tried this on my bricked xperia c red led
Few weeks back no success
Logic
If you flash wrong recovery there is no way to boot in any mode
I can say this with 100% confident as I had spent full 3 days and tried every thing...
If u wona check goto custome mod for xperia c thred and get recovery installed
Then try this and share results
All the best
Click to expand...
Click to collapse
I flashed a faulty recovery using mobileuncles and there was no signs of life other than a red led liggt, and holding power + volume up works just fine and it went into flashmode.
I have the same issue.
I organized xperia light rom for our xperia c, I flashed it from custom recovery. Phone is completely dead now.
There is a just red light, phone does not go into download or fastboot mode. Pc Companion, Sony Update Center, Wmshua Flashtool do not recognize the phone.
Any suggestion with that?
I don't have warranty, my last option is to pay money for technical service.
this worked for me but instead of POWER+VOL UP i used POWER+VOL DOWN
thanks
thank, i like this forum
worth to try... (hope it won't happen to me :laugh: )
I have experienced this too, however, instead of using the Sony Update Service, I used the Sony PC Companion. At first it was not working, so I did a hard reset on the phone (press the button at the back). I held the power+up button while inserting the cable, and finally it was detected by Sony. It will reset your device to factory settings though.
seiferfury said:
I have experienced this too, however, instead of using the Sony Update Service, I used the Sony PC Companion. At first it was not working, so I did a hard reset on the phone (press the button at the back). I held the power+up button while inserting the cable, and finally it was detected by Sony. It will reset your device to factory settings though.
Click to expand...
Click to collapse
How did it
How Catch 4 buttons simultaneously
Please reply to the importance of
Im in the same scenario.. I tried all the procedures here but i failed.. I noticed that when i connect it, it disconnects after a while along with blinking of led light then reconnect again. And my PC detects it as unknown device.. I tried to install ADB driver but it also fails. Please help me.. Thanks. Sorry about my English
zergmac023 said:
Im in the same scenario.. I tried all the procedures here but i failed.. I noticed that when i connect it, it disconnects after a while along with blinking of led light then reconnect again. And my PC detects it as unknown device.. I tried to install ADB driver but it also fails. Please help me.. Thanks. Sorry about my English
Click to expand...
Click to collapse
If you flash a different device's rom, it happens. If you replace your motherboard, it will work again.
(
TacoNikky said:
If you flash a different device's rom, it happens. If you replace your motherboard, it will work again.
Click to expand...
Click to collapse
Which probably crying::crying::crying:
yeubeo168 said:
Which probably crying::crying::crying:
Click to expand...
Click to collapse
I have bought motherboard from china http://www.yoybuy.com/en/show/37431065583/ from this seller.
It took 20 days to arrive to Turkey. I have changed my motherboard and my phone is back right now :victory:
It works like a charm. Model number changed, it shows s39h but phone works like old days :good:
A detailed guide :
http://forum.xda-developers.com/sony-xperia-c/general/how-to-install-restore-stock-android-t2832005
It worked!!!!!
GethPrime said:
Fix Xperia C Red Light brick
Are you facing that the red led on your device blinks and there is no other signs of life? Then you are in the correct thread, I faced this issue when flashing a corrupted recovery but then I found out a easy way to fix it without opening the device or sending it in to Sony.
Requirements:
1. The first thing you need to do is to make sure that you have downloaded Sony Update Service and have installed it onto your PC from the link above, if not, do it now.
2. Now launch Sony Update Service and select Xperia C in the list and then press Next.
3. Hold the Volume Up button and plugin microusbcable while doing so, if that doesn't work for you, hold power + volume up and plugin the microusbcable while doing. Keep holding button combination for a few seconds and wait for a green light on your phone, if it appears check on
your PC so that it's detected.
4. Wait while the firmware is being downloaded and reinstalled on your phone and enjoy your working device!
Click to expand...
Click to collapse
It worked for my Xperia M (rooted on JB 4.3) with a locked bootloader which was STUCK on bootloop screen and when I did the whole thing with holding the power and volume up button (after I let the battery die after so many bootloops it did), FINALLY I was able to take it to flashmode, while I had selected from Sony PC Companion to repair my phone, and after 3-4 tries, I DID IT!!! Thank you so much for this thread ( I DEFINITELY pressed the "thanks" button), it really SAVED ME time and money (because I was planning to send it to Sony to fix it and you ALL know how bastards Sony is)!!!! And to all those of you who are DESPERATE to fix their phone (I hope you read this thread), DON'T PANIC, and DON'T GIVE UP!!! It took me 2 days of searching the web, and FINALLY I MADE IT!!! There are ALWAYS solutions to these kinds of problems!!!!
red light
dear friends please help me. I wanted to install cwm recovery with mobile uncle tools. when I placed recovery.img to phone memory(not in any folder), it didn't find the file, but when in sd card(not in any folder) it succesfully find. I selected and flashed, but the phone shut down and didn't start anymore. yesterday, when plugging to charge the red light under the screen was blinking. but today, it just stays on, not blinking, but after some time, goes off again, and start blinking. when I connect to PC, first it connects, after some time connection is lost and green light passes to red again, after some time it again connects. I tried Sony Update Service and PC Companion, didn't work. Please help...
Need help
same here only red light is blinking,,,i tried doing Power+vol up and Power+vol down and by inserting cable also...it just show a red light when plugged in
i'm also having the same problem....somebody please help!!!!really need to use it
kamran.kerim said:
dear friends please help me. I wanted to install cwm recovery with mobile uncle tools. when I placed recovery.img to phone memory(not in any folder), it didn't find the file, but when in sd card(not in any folder) it succesfully find. I selected and flashed, but the phone shut down and didn't start anymore. yesterday, when plugging to charge the red light under the screen was blinking. but today, it just stays on, not blinking, but after some time, goes off again, and start blinking. when I connect to PC, first it connects, after some time connection is lost and green light passes to red again, after some time it again connects. I tried Sony Update Service and PC Companion, didn't work. Please help...
Click to expand...
Click to collapse
i'm also having the same problem....somebody please help!!!!really need to use it
chauhanjayc said:
Have tried this on my bricked xperia c red led
Few weeks back no success
Logic
If you flash wrong recovery there is no way to boot in any mode
I can say this with 100% confident as I had spent full 3 days and tried every thing...
If u wona check goto custome mod for xperia c thred and get recovery installed
Then try this and share results
All the best
Click to expand...
Click to collapse
Does that mean phone is dead?
choxx said:
Does that mean phone is dead?
Click to expand...
Click to collapse
no all you need stock kernel
you can either google it or download ftf and check all except kernel
done
I've got a z5 dual e6683 not working properly for 6 months.
Some day, it just started not charging when the phone was on. I waited till battery died, then plugged it in wall charger and it got up to 100%. I managed to start the phone and then it was ok. I charged it a couple of time in 2 days, and then suddenly doesn't recognizes charge anymore... I also can't turn it off; when i turn off, it stops and restarts immediatly in bootloop. I managed to force it to stop by pressing power and both + and - volume but even then its not totally off, it still displays battery level...... Any ideas ?
Thanks
Wait for battery do die completely, then hold volume down and plug usb cable if it turns green then flashmode works and you can flash new firmware, maybe it will fix the issue
L33Tgod said:
Wait for battery do die completely, then hold volume down and plug usb cable if it turns green then flashmode works and you can flash new firmware, maybe it will fix the issue
Click to expand...
Click to collapse
i'm gonna try that. Do you have any idea which firmware i can use ? I actually have 32.2.A.5.11 RU.
jackijumbo90 said:
i'm gonna try that. Do you have any idea which firmware i can use ? I actually have 32.2.A.5.11 RU.
Click to expand...
Click to collapse
try reflashing, but do clean wipe
L33Tgod said:
try reflashing, but do clean wipe
Click to expand...
Click to collapse
I managed to boot in flashmode and flash a previous version of the same firmware but i'm still experiencing the same problems......
did it fall in water by any chance?
a00r said:
did it fall in water by any chance?
Click to expand...
Click to collapse
no, it didn't fall. I used it whithout any problem during 6 months and then it just strated buging... Sony won't take it under warranty since i bought it from Hong kong (no dual sim version in Europe at the time...)
another symptom is that, when flashtool is done and says disconnect and restart, i disconnect the phone from the computer and it boots on its own...
jackijumbo90 said:
another symptom is that, when flashtool is done and says disconnect and restart, i disconnect the phone from the computer and it boots on its own...
Click to expand...
Click to collapse
try selecting all to wipe in flashtool if you dont have any important files on it
L33Tgod said:
try selecting all to wipe in flashtool if you dont have any important files on it
Click to expand...
Click to collapse
that's what i did.
jackijumbo90 said:
that's what i did.
Click to expand...
Click to collapse
well go to service, not sony, but normal service and ask are they familiar with that behaviour
My honor 8 died on the lancet side lights up 1 red led and then 5 times the green led and then come back. The usb connection is dead so I can not work with any program to try to re-enable it ....
Anyone can give me an explanation of what these LEDs can be ???
Thanks to anyone can give me just an indication:confuso:
This situation was created after an upgrade I believe with firmware no good
Repeat push power button vibration and usb dead pc does not detect, anything starts then flash 1 red led and then 5 green repeat this cycle 3 times then turn off
Rommco05 said:
If turn phone to charge looks like start charging?
Click to expand...
Click to collapse
If I connect the phone to the charger does not turn on anything does not charge ...... after 3/4 hours I find it hot.
The usb is no longer responding to anything ......
Only the power button makes it vibrate one time and after a second the second vibration and starts doing that notification led sequence
Thanks for the interest you are very kind
I've been trying to load it all night but nothing has changed.
From the calculations I did during the last flash within the update.app, these images were deleted: sha256rsa, crc, curver, verilist, efi, fastboot to try a recovery.
After this happened ..........................
I was programming with dc-unlocker
Thanks again for your help.
traffic75 said:
Thanks for the interest you are very kind
I've been trying to load it all night but nothing has changed.
From the calculations I did during the last flash within the update.app, these images were deleted: sha256rsa, crc, curver, verilist, efi, fastboot to try a recovery.
After this happened ..........................
I was programming with dc-unlocker
Thanks again for your help.
Click to expand...
Click to collapse
let us know what steps you followed after your device is working
goodluck
venugopalu007 said:
let us know what steps you followed after your device is working
goodluck
Click to expand...
Click to collapse
Nothing has changed at this time
I'm trying different combinations with the tast but nothing to do ......
The biggest problem that the usb is not detected and can not attach it to the pc
I've already tried with usb 2.0 always dead
I've tried in power on all keystrokes and I've never heard sound recognition windows usb
On no , no fastboot we cannot do anything .just take it to care and they will fix it .
And dload option with the correct firmware in the sd card not work starting with 3 buttons method?
I'll make it pretty easier for you if it's your luck that shines your phone will revive
First do this
Plug in your us type c port of your charger on the phone while holding volume up button for like five seconds. Then leave it to charge for 5-10 minutes and the press power button simply . If it revives , good! If not, let's continue
Now if this didn't work and your have one very simple option of press the volume low key and power button while plugging in your usb type c , which is connected to a PC.
This will open your fastboot and rescue more - open hisuit on pc , hit recovery and it should do the magic
If this also doesn't work , try unlocking bootloader via the same process and flash a recovery and receive your phone.
If nothing of this works , welcome to the league of dead honor 8.
amansaini said:
I'll make it pretty easier for you if it's your luck that shines your phone will revive
First do this
Plug in your us type c port of your charger on the phone while holding volume up button for like five seconds. Then leave it to charge for 5-10 minutes and the press power button simply . If it revives , good! If not, let's continue
Now if this didn't work and your have one very simple option of press the volume low key and power button while plugging in your usb type c , which is connected to a PC.
This will open your fastboot and rescue more - open hisuit on pc , hit recovery and it should do the magic
If this also doesn't work , try unlocking bootloader via the same process and flash a recovery and receive your phone.
If nothing of this works , welcome to the league of dead honor 8.
Click to expand...
Click to collapse
I tried but all this does not work is always stuck with that led combination and usb is death
Thanks anyway for your interest
traffic75 said:
I tried but all this does not work is always stuck with that led combination and usb is death
Thanks anyway for your interest[/QUOT
I contacted dc-unlocker what I was using and advised me to try to short-circuit and pass a fimware test I should succeed. But he does not have short-circuit procedures for my honor8.
Have any of you ever heard of this technique?
Click to expand...
Click to collapse
traffic75 said:
traffic75 said:
I tried but all this does not work is always stuck with that led combination and usb is death
Thanks anyway for your interest[/QUOT
I contacted dc-unlocker what I was using and advised me to try to short-circuit and pass a fimware test I should succeed. But he does not have short-circuit procedures for my honor8.
Have any of you ever heard of this technique?
Click to expand...
Click to collapse
Short circuit ?? What is that bro?
Click to expand...
Click to collapse
I want to ask for help: I'm not sure but could start charging a firmware including bootloader iso when booting with the led.
The function is through the SD with the dload in the previous models used by au_temp.cfg and the firm update.app I believe au_temp.cfg can give instructions to switch to the firm's upload.
The problem I find nothing au_temp.cfg for my Honor 8.
Can someone help me??? Any of you have contacts with huawei to ask this info ????
Thanks to anyone who can really help me
help me !!! help me!!
Rommco05 said:
Which port u use, usb 3.0 or usb 2.0 if 3.0 switch to 2.0z anyway I think u need to go service
Click to expand...
Click to collapse
sorry sorry sorry
I was sure I replied sorry
I tried usb 3.0 at 2.0 but there is no connection.
I tried jun and power button for 5 minutes as suggested by digigoon but the situation does not change.
The phone does not turn on the screen vibrates only when the power button is pressed and leds are lit red and 5 times green for 2 repeats and then turn off.
I'm looking everywhere but nothing exists for my problem.
"The phone worked I dc-unlocked a firm without img sha256rsa, crc, curver, verlist, efi, fastboot, to try an update and that was the result ..........:crying::crying::crying::crying::crying::crying::crying::crying:
Hello friend
I'm sorry about your situation. I googled a bit to try to find a solution and what I found was this:
https://www.google.dk/url?sa=t&sour...ggzMAU&usg=AFQjCNHnbiPHjoFd2-SXkWsS_zzHVxM1-w
It seems like three persons in this thread had the same problem and two of them had tried returning the phone to a service center and got it repaired for free.
Maybe it is a fried motherboard and if that is the case they will never know that you tried flashing anything on the ROM.
All the best!
Ihaveatattoo said:
Hello friend
I'm sorry about your situation. I googled a bit to try to find a solution and what I found was this:
https://www.google.dk/url?sa=t&sour...ggzMAU&usg=AFQjCNHnbiPHjoFd2-SXkWsS_zzHVxM1-w
It seems like three persons in this thread had the same problem and two of them had tried returning the phone to a service center and got it repaired for free.
Maybe it is a fried motherboard and if that is the case they will never know that you tried flashing anything on the ROM.
All the best!
Click to expand...
Click to collapse
I've also seen them in my own situation ...... huawei's only solution solution.
Under these conditions it does not respond to any command ......
Rommco05 said:
I really don't know what next, don't have answer to your question
Click to expand...
Click to collapse
Rommcon05 If you may think of some other try I'm here
Rommco05 said:
Leave phone somehow discharged in some situation this can help
Click to expand...
Click to collapse
You intend to let it discharged completely for 4.5 days ????
I was using lrteam twrp 3.4.2b-1206 and I was sideloading the vendor update for 12.2.1.0 when the progress bar froze. I gave it 10 minutes and held the power button to reboot and now the phone is showing no signs of life i cant get it to even show the poco screen. I've got no ideas left on what to do.
ashawanz said:
I was using lrteam twrp 3.4.2b-1206 and I was sideloading the vendor update for 12.2.1.0 when the progress bar froze. I gave it 10 minutes and held the power button to reboot and now the phone is showing no signs of life i cant get it to even show the poco screen. I've got no ideas left on what to do.
Click to expand...
Click to collapse
Did you try holding power and volume down? Also charge it for some hours.
Tecardo said:
Did you try holding power and volume down? Also charge it for some hours.
Click to expand...
Click to collapse
yeah no combination of buttons will show any signs of life and i can't even get to the bootloader. It should be at 100% battery at this point i dont think that's the issue either
Where did you find vendor update for 12.2.1.0 ?
NOSS8 said:
Where did you find vendor update for 12.2.1.0 ?
Click to expand...
Click to collapse
Some users postet from Xiaomi firmware website (non official) . Link is in many rom threads
ashawanz said:
yeah no combination of buttons will show any signs of life and i can't even get to the bootloader. It should be at 100% battery at this point i dont think that's the issue either
Click to expand...
Click to collapse
Did you attach it to pc and see what device gets detected then? It could be in qualcomm usb mode
Tecardo said:
Some users postet from Xiaomi firmware website (non official) . Link is in many rom threads
Click to expand...
Click to collapse
Firmeware not vendor,not the same.
is the phone appear on pc?
Tecardo said:
Did you attach it to pc and see what device gets detected then? It could be in qualcomm usb mode
Click to expand...
Click to collapse
If the the phone appear in qualcom usb, flashing in EDL will be possible and requires an authorization that only official repairers have.
NOSS8 said:
Firmeware not vendor,not the same.
is the phone appear on pc?
Click to expand...
Click to collapse
as I remember it's included? Otherwise use Xiaomi eu rom. It's including vendor.
Tecardo said:
as I remember it's included? Otherwise use Xiaomi eu rom. It's including vendor.
Click to expand...
Click to collapse
My first question was for ashawanz" Where did you find vendor update for 12.2.1.0 ? "
and this answer" If the the phone appear in qualcom usb, flashing in EDL will be possible and requires an authorization that only official repairers have" was not intended for you 'my mistake' but still for ashawanz
ashawanz said:
yeah no combination of buttons will show any signs of life and i can't even get to the bootloader. It should be at 100% battery at this point i dont think that's the issue either
Click to expand...
Click to collapse
Where did you find vendor update for 12.2.1.0 ?
Firmeware not vendor,not the same.
is the phone appear on pc?
If the the phone appear in qualcom usb, flashing in EDL will be possible and requires an authorization that only official repairers have.
Tecardo said:
Did you attach it to pc and see what device gets detected then? It could be in qualcomm usb mode
Click to expand...
Click to collapse
So I just took the device apart to try and get into qualcomm edl mode through hardware and now the front camera led turns red while charging. apart from that there are no signs of life though it won't show up in my pc's device manager even though I have the qualcomm drivers
ashawanz said:
So I just took the device apart to try and get into qualcomm edl mode through hardware and now the front camera led turns red while charging. apart from that there are no signs of life though it won't show up in my pc's device manager even though I have the qualcomm drivers
Click to expand...
Click to collapse
So you should let it charge till later in 6h
NOSS8 said:
Where did you find vendor update for 12.2.1.0 ?
Firmeware not vendor,not the same.
is the phone appear on pc?
If the the phone appear in qualcom usb, flashing in EDL will be possible and requires an authorization that only official repairers have.
Click to expand...
Click to collapse
Phone does not appear on pc and I got it from the evoX 5.1 thread. Ive flashed it before however and it didn't do this it worked just fine
ashawanz said:
Phone does not appear on pc and I got it from the evoX 5.1 thread. Ive flashed it before however and it didn't do this it worked just fine
Click to expand...
Click to collapse
This is the correct firmware.
What do you want to do in EDL mode?
NOSS8 said:
This is the correct firmware.
What do you want to do in EDL mode?
Click to expand...
Click to collapse
It's not booting, he doesn't want to get into edl. It's showing no reaction. But he could try pressing power button for 1min and look for vibration
To try to restore the phone yourself, you must use commands in fastboot or adb.
Tecardo said:
It's not booting, he doesn't want to get into edl. It's showing no reaction. But he could try pressing power button for 1min and look for vibration
Click to expand...
Click to collapse
the power button for a minute didnt do anything either sadly. Im trying to get into edl so i can try and recover it with QPST, but even after opening the phone up and trying to get into edl through hardware, i was only able to get the red charging light to start showing whilst charging. Should I try to disconnect and reconnect the battery maybe?
ashawanz said:
the power button for a minute didnt do anything either sadly. Im trying to get into edl so i can try and recover it with QPST, but even after opening the phone up and trying to get into edl through hardware, i was only able to get the red charging light to start showing whilst charging. Should I try to disconnect and reconnect the battery maybe?
Click to expand...
Click to collapse
Yep, can't hurt at this point.
You can try this:
Recharge the battery for at least 1 hour (even if you think it is already charged)
after connect it by usb and press the power button first,power button with volume -, button with volume +, and try to see if it appears on the pc and in what way.
Hello, please help. I have a big problem.
I just flashed custom ROM and the installation was successful. When I restarted the phone, it stopped at the "Samsung Galaxy" logo and did not complete and then restarted automatically in this case. I tried to enter twrp, but to no avail. I also tried Entering the download mode, but also it does not work
I hope that someone will help me, and is this how the phone was damaged, or is there hope to recover it?
Try holding power and volume down for over 20 seconds, after the phone reboot keep holding those keys and hope you get into download mode
Zakaria2328 said:
Try holding power and volume down for over 20 seconds, after the phone reboot keep holding those keys and hope you get into download mode
Click to expand...
Click to collapse
Thx bro, but it didn't work
mhmdhousni said:
Thx bro, but it didn't work
Click to expand...
Click to collapse
Does Odin recognise the phone?
mhmdhousni said:
Hello, please help. I have a big problem.
I just flashed custom ROM and the installation was successful. When I restarted the phone, it stopped at the "Samsung Galaxy" logo and did not complete and then restarted automatically in this case. I tried to enter twrp, but to no avail. I also tried Entering the download mode, but also it does not work
I hope that someone will help me, and is this how the phone was damaged, or is there hope to recover it?
Click to expand...
Click to collapse
completely switch off the phone. hold volume up and volume down together and connect usb cable.
Zakaria2328 said:
Does Odin recognise the phone?
Click to expand...
Click to collapse
Unfortunately not, I even tried to enter it into download mode by pressing the volume up and down buttons and then connecting the USB, and it did not work, so I think it may need a board
mvikrant97 said:
completely switch off the phone. hold volume up and volume down together and connect usb cable.
Click to expand...
Click to collapse
I tried this and it didn't work either
mhmdhousni said:
I tried this and it didn't work either
Click to expand...
Click to collapse
Can you disassemble the phone and remove the battery and reconnect it again and try to put it into download mode?
mvikrant97 said:
Can you disassemble the phone and remove the battery and reconnect it again and try to put it into download mode?
Click to expand...
Click to collapse
Honestly, no, I haven't tried jaw before But I waited until the battery ran out and tried again to insert the download, but it didn't work either,,, I have a question I first formatted and then installed the ROM, then it succeeded, but after the word “installation was successful” there were words in red “failed mount system root” Then I flashed the rest of the ROM files, then I thought it was over, so I restarted, but it stopped at the "samsung galay - secured by Knox" logo. It does not continue and then restarts itself in this case and does not stop until the battery runs out and stops then I tried to enter the recovery but to no avail and also the same thing with the download mode,, summarizing all this does the phone need a motherboard, or that the matter can be solved?
mhmdhousni said:
Honestly, no, I haven't tried jaw before But I waited until the battery ran out and tried again to insert the download, but it didn't work either,,, I have a question I first formatted and then installed the ROM, then it succeeded, but after the word “installation was successful” there were words in red “failed mount system root” Then I flashed the rest of the ROM files, then I thought it was over, so I restarted, but it stopped at the "samsung galay - secured by Knox" logo. It does not continue and then restarts itself in this case and does not stop until the battery runs out and stops then I tried to enter the recovery but to no avail and also the same thing with the download mode,, summarizing all this does the phone need a motherboard, or that the matter can be solved?
Click to expand...
Click to collapse
It can be solved. It doesn't need a motherboard.
Try Chimera tool. It can fix dead boot. You may need to short test point of your phone so that the software recognises your phone.
mvikrant97 said:
It can be solved. It doesn't need a motherboard.
Try Chimera tool. It can fix dead boot. You may need to short test point of your phone so that the software recognises your phone.
Click to expand...
Click to collapse
I really appreciate your help, but can you tell me how to use it? I will do this later because I am busy during this period
mhmdhousni said:
I really appreciate your help, but can you tell me how to use it? I will do this later because I am busy during this period
Click to expand...
Click to collapse
Yeah sure. Its pretty straight forward. You can find tutorials on YouTube.
mvikrant97 said:
Yeah sure. Its pretty straight forward. You can find tutorials on YouTube.
Click to expand...
Click to collapse
Well, I'll look into it, thank u sir <3