Hi
I am in the process of rooting my phone for the first time, while reading through the instructions (http://forum.xda-developers.com/showthread.php?t=788044 ) , I have tried to download the USB drivers required (Here: http://downloads.unrevoked.com/recovery/android-usb-driver.zip )
Unfortunately, the link seems to be dead, and after searching on google and this forum I still havent found the drivers, So i was wondering if someone on here could help me by sharing an alternative link or reuploading them?
I would greatly appeciate any help
regards
Link is not dead.
I get the error message
" 403 - Forbidden"
when i try to access the page, any idea why?
Hi, i managed to solve the problem, it was down to my browser/ISP,
apologies,
please close
stuck a copy here: http://www.4shared.com/file/2vSCKQGF/android-usb-driver.html but I'd recommend going to unrevoked first just in case they updated it
if it's not ok to host that driver there too then if someone lets me know i'll remove.
Hi!
Though I could find similar queries raised for such issue...but could not find any solution or any post for my device.
My tab got bricked while flashing CWM...and I managed to unbrick it with Livesuit-Yalker as given in the link below:
http://forum.xda-developers.com/showthread.php?t=2104473
Then I could also restore it to stock file as given in the thread above (2012-09-25.11.49.26). Touch was not working, which I fixed by loading "sun4i_crane_M1005_P500.20120727.rar" file.
But now I am stuck at wifi not turning on issue, and did 2-3 times Yarvik-Stock-factory reset-Power tab JB-Lightning ROM- etc..but nothing is able to turn the wifi ON. As without wifi this device is hardly of any use, any suggestions would help to get it fixed!
I found on post which is to fix this issue for phones, but again, I do not know how can I enter the *# codes on wifi tab.
"Step 1: Dial *#*#526#*#* into your phone's keypad. It will show a message "Driver Loading Successful . If this is the message that comes up on the screen, than wifi should work now fine. If you get "Driver Loading Unsuccessful" on the screen then you should move on to Step 2.
Step 2: Dial *#*#526#*#* again and this time click on the options button.
Step 3: Select Rx Test.
Step 4: Now select Channel >9.
Step 5: Click Start and exit."
BR//Sumit
Did you find an answer
sumit0110 said:
Hi!
Though I could find similar queries raised for such issue...but could not find any solution or any post for my device.
My tab got bricked while flashing CWM...and I managed to unbrick it with Livesuit-Yalker as given in the link below:
http://forum.xda-developers.com/showthread.php?t=2104473
Then I could also restore it to stock file as given in the thread above (2012-09-25.11.49.26). Touch was not working, which I fixed by loading "sun4i_crane_M1005_P500.20120727.rar" file.
But now I am stuck at wifi not turning on issue, and did 2-3 times Yarvik-Stock-factory reset-Power tab JB-Lightning ROM- etc..but nothing is able to turn the wifi ON. As without wifi this device is hardly of any use, any suggestions would help to get it fixed!
I found on post which is to fix this issue for phones, but again, I do not know how can I enter the *# codes on wifi tab.
"Step 1: Dial *#*#526#*#* into your phone's keypad. It will show a message "Driver Loading Successful . If this is the message that comes up on the screen, than wifi should work now fine. If you get "Driver Loading Unsuccessful" on the screen then you should move on to Step 2.
Step 2: Dial *#*#526#*#* again and this time click on the options button.
Step 3: Select Rx Test.
Step 4: Now select Channel >9.
Step 5: Click Start and exit."
BR//Sumit
Click to expand...
Click to collapse
Did you find answer to your question?? i am still looking for an answer
varunvarde2007 said:
Did you find answer to your question?? i am still looking for an answer
Click to expand...
Click to collapse
Hi! worked for me after I install firmware for curtis plt1044...
Cannot post direct URLs here.... you can Google below
curtis plt1044 firmware
facing this problem in funbook alpha
sumit0110 said:
Hi!
Though I could find similar queries raised for such issue...but could not find any solution or any post for my device.
My tab got bricked while flashing CWM...and I managed to unbrick it with Livesuit-Yalker as given in the link below:
http://forum.xda-developers.com/showthread.php?t=2104473
Then I could also restore it to stock file as given in the thread above (2012-09-25.11.49.26). Touch was not working, which I fixed by loading "sun4i_crane_M1005_P500.20120727.rar" file.
But now I am stuck at wifi not turning on issue, and did 2-3 times Yarvik-Stock-factory reset-Power tab JB-Lightning ROM- etc..but nothing is able to turn the wifi ON. As without wifi this device is hardly of any use, any suggestions would help to get it fixed!
I found on post which is to fix this issue for phones, but again, I do not know how can I enter the *# codes on wifi tab.
"Step 1: Dial *#*#526#*#* into your phone's keypad. It will show a message "Driver Loading Successful . If this is the message that comes up on the screen, than wifi should work now fine. If you get "Driver Loading Unsuccessful" on the screen then you should move on to Step 2.
Step 2: Dial *#*#526#*#* again and this time click on the options button.
Step 3: Select Rx Test.
Step 4: Now select Channel >9.
Step 5: Click Start and exit."
BR//Sumit
Click to expand...
Click to collapse
I have the same problem in funbook alpha
sumit0110 said:
Hi! worked for me after I install firmware for curtis plt1044...
Cannot post direct URLs here.... you can Google below
curtis plt1044 firmware
Click to expand...
Click to collapse
After installing this firmware w-fi began to work normally? What did you do then? Flashed the original firmware?
Thanks!
I stayed on the curtis firmware..
//Sumit
Hello friends,
first of all thanks to everyone who supported me to fix my phone.( took me nearly 2 days)
this thread is for the people who bricked their phone while re-branding etcetra and to recover it in easy steps.
First make a note of your IMEI, Product ID, Sno. before proceeding.
1. Download hwota.zip from the link provided.( consist of all oeminfo needed )
https://drive.google.com/open?id=10fNOKja7MD0MOtlPVQH5S9kQ2czdn9dC
2.Unzip to your local c: drive
3.Now download stock firmware of your model or rebranded model number from this website https://www.gizrom.com/huawei-mate-9-stock-rom/
4.after downloading place the files in UNZIPPED FOLDER of HWOTA.ZIP in UPDATE FOLDER.
5.Rename the file as following " update.zip " , " update_all_hw.zip " , update_data_public.zip" . very imp plz.
6.Now open "update.bat"
7.Follow the instructions. You will need your device unlocking code in order to unlock bootloader and install twrp. SO MAKE A NOTE OF YOUR UNLOCK CODE AND SAVE IT.
8.For those your are having trouble finding SNo. and Product id can check from this website or can use HUAWEI PRODUCT ID Generator.
https://imei24.com/warranty_info/Huawei/861956030103197/
9.Now, after following instructions your device will reboot and start factory reset, if it fails then don't worry just hold "power + Vol up " to boot into recovery wipe partition then wipe data (factory reset ) then reboot.
DONE!
10.For those who are having trouble with MEID showing 000000000 don't worry its just for MHA-L09(single sim) showing it as dual sim....but sim works absolutely perfect.
11.For those who want to install oreo they follow same above HWOTA procedure, download official oreo from
https://romprovider.com/2017/11/update-emui-8-0-huawei-mate-9/
That's it!!!!!
If you have any problem installing firmware, feel free to post in this thread, il try to reply asap..:good::good:
GOOD LUCK.
Shadymind said:
Hello friends,
first of all thanks to everyone who supported me to fix my phone.( took me nearly 2 days)
this thread is for the people who bricked their phone while re-branding etcetra and to recover it in easy steps.
First make a note of your IMEI, Product ID, Sno. before proceeding.
1. Download hwota.zip from the link provided.( consist of all oeminfo needed )
https://drive.google.com/open?id=10fNOKja7MD0MOtlPVQH5S9kQ2czdn9dC
2.Unzip to your local c: drive
3.Now download stock firmware of your model or rebranded model number from this website https://www.gizrom.com/huawei-mate-9-stock-rom/
4.after downloading place the files in UNZIPPED FOLDER of HWOTA.ZIP in UPDATE FOLDER.
5.Rename the file as following " update.zip " , " update_all_hw.zip " , update_data_public.zip" . very imp plz.
6.Now open "update.bat"
7.Follow the instructions. You will need your device unlocking code in order to unlock bootloader and install twrp. SO MAKE A NOTE OF YOUR UNLOCK CODE AND SAVE IT.
8.For those your are having trouble finding SNo. and Product id can check from this website or can use HUAWEI PRODUCT ID Generator.
https://imei24.com/warranty_info/Huawei/861956030103197/
9.Now, after following instructions your device will reboot and start factory reset, if it fails then don't worry just hold "power + Vol up " to boot into recovery wipe partition then wipe data (factory reset ) then reboot.
DONE!
10.For those who are having trouble with MEID showing 000000000 don't worry its just for MHA-L09(single sim) showing it as dual sim....but sim works absolutely perfect.
11.For those who want to install oreo they follow same above HWOTA procedure, download official oreo from
https://romprovider.com/2017/11/update-emui-8-0-huawei-mate-9/
That's it!!!!!
If you have any problem installing firmware, feel free to post in this thread, il try to reply asap..:good::good:
GOOD LUCK.
Click to expand...
Click to collapse
mate 9 mha l29 mha c185b188
I tried to update to oreu the hwota method every thing OK but when phone restart 14% then instillation field!!
the I tried Re-branding method same ( every thing complete ) when phone restart instillation field
the when restart phone say error redownload update again ... no image error n 2
how to recover stuck room!!!
plz help
Abody.sy said:
mate 9 mha l29 mha c185b188
I tried to update to oreu the hwota method every thing OK but when phone restart 14% then instillation field!!
the I tried Re-branding method same ( every thing complete ) when phone restart instillation field
the when restart phone say error redownload update again ... no image error n 2
how to recover stuck room!!!
plz help
Click to expand...
Click to collapse
Could you post an image of the error screen?
phone still not booting
Hi I followed all steps on your thread but when my phone booted up it says "software install failed" And everytime I boot up after that it takes me to Erecovery,I tried wiping cache partition and factory reset from recovery mode but the factory reset fails at 5%,what am I doing wrong? My phone has been like this for 3 weeks
prenesin said:
Hi I followed all steps on your thread but when my phone booted up it says "software install failed" And everytime I boot up after that it takes me to Erecovery,I tried wiping cache partition and factory reset from recovery mode but the factory reset fails at 5%,what am I doing wrong? My phone has been like this for 3 weeks
Click to expand...
Click to collapse
Is your FRP unlocked?
You can check by booting to fastboot mode.
Download minimal adb & fastboot installer. Install.
Put phone in fastboot mode by plugging in USB to computer and then start using power + vol down.
If it says FRP unlock its pretty easy to fix.
If not you could try factory reset from recovery, then back to fastboot mode and check if FRP is gone.
Check this and reply back.
frp unlock?
ante0 said:
Is your FRP unlocked?
You can check by booting to fastboot mode.
Download minimal adb & fastboot installer. Install.
Put phone in fastboot mode by plugging in USB to computer and then start using power + vol down.
If it says FRP unlock its pretty easy to fix.
If not you could try factory reset from recovery, then back to fastboot mode and check if FRP is gone.
Check this and reply back.
Click to expand...
Click to collapse
I don't know about frp unlock,I only know bootloader unlock,I press the volume down button while doing that I connect it to the pc,my phone displays "phone unlocked"is that the same as frp?
prenesin said:
I don't know about frp unlock,I only know bootloader unlock,I press the volume down button while doing that I connect it to the pc,my phone displays "phone unlocked"is that the same as frp?
Click to expand...
Click to collapse
If it just says that, and not FRP locked, you can use this guide to rebrand and/or get a working firmware.
https://forum.xda-developers.com/mate-9/how-to/guide-mate-9-flash-update-package-t3593108
I realise it's the same hwota as OP posted but it's explained a little more in the release thread.
Does the bat give any errors?
phone still not booting
ante0 said:
f it just says that, and not FRP locked, you can use this guide to rebrand and/or get a working firmware.
https://forum.xda-developers.com/mate-9/how-to/guide-mate-9-flash-update-package-t3593108
I realise it's the same hwota as OP posted but it's explained a little more in the release thread.
Does the bat give any errors?
Click to expand...
Click to collapse
The bat does not give me any errors, everything works as explained but once it's time for the phone to boot up it says software install failed,than it boots to Erecovery,I even did it twice first was rebrand than same model update but the phone still doesn't boot up
Phone finally booted up almost good as new
Shadymind said:
Hello friends,
first of all thanks to everyone who supported me to fix my phone.( took me nearly 2 days)
this thread is for the people who bricked their phone while re-branding etcetra and to recover it in easy steps.
First make a note of your IMEI, Product ID, Sno. before proceeding.
1. Download hwota.zip from the link provided.( consist of all oeminfo needed )
https://drive.google.com/open?id=10fNOKja7MD0MOtlPVQH5S9kQ2czdn9dC
2.Unzip to your local c: drive
3.Now download stock firmware of your model or rebranded model number from this website https://www.gizrom.com/huawei-mate-9-stock-rom/
4.after downloading place the files in UNZIPPED FOLDER of HWOTA.ZIP in UPDATE FOLDER.
5.Rename the file as following " update.zip " , " update_all_hw.zip " , update_data_public.zip" . very imp plz.
6.Now open "update.bat"
7.Follow the instructions. You will need your device unlocking code in order to unlock bootloader and install twrp. SO MAKE A NOTE OF YOUR UNLOCK CODE AND SAVE IT.
8.For those your are having trouble finding SNo. and Product id can check from this website or can use HUAWEI PRODUCT ID Generator.
https://imei24.com/warranty_info/Huawei/861956030103197/
9.Now, after following instructions your device will reboot and start factory reset, if it fails then don't worry just hold "power + Vol up " to boot into recovery wipe partition then wipe data (factory reset ) then reboot.
DONE!
10.For those who are having trouble with MEID showing 000000000 don't worry its just for MHA-L09(single sim) showing it as dual sim....but sim works absolutely perfect.
11.For those who want to install oreo they follow same above HWOTA procedure, download official oreo from
https://romprovider.com/2017/11/update-emui-8-0-huawei-mate-9/
That's it!!!!!
If you have any problem installing firmware, feel free to post in this thread, il try to reply asap..:good::good:
GOOD LUCK.
Click to expand...
Click to collapse
Thanks to this post my Huawei mate 9 is finally working, tried restoring it for the past 3 weeks but nothing, this was the only method that worked for me, everything on the phone works perfectly except that my single Sim Sim now says it's a dual Sim(MEID showing a lot of zeros) , but I'm just glad it's working after all this time, thank you to everyone who helped
Hi
Can you help me please ?
https://forum.xda-developers.com/mate-9/help/huawei-mate-9-mha-l09-mha-l29-t3738376
Thank you
Hi
Please can you tell to me why when HWOTA wait my phone in TWRP mode do not detect my phone ? Thank you
Please help
My mate 9 had a security patch dated in April last year. I was trying to update it to a recent patch. I tried a couple OTA passages on FF, but none of them could finish and left me with a starting screen saying your phone failed for verification. So I tried a full OTA package ( don't remember the number more, but it's a package dated Jan 7th I think) that passed the access test in FF.
The whole process finished and screen showed update successful. But all of a sudden, instead of normal restart, the phone started a downgrade process and tried to install B567 back to my phone. Then it kept going to erecovery, but always showed recovery failed after downloading a package from server and trying to install it.
I don't want to void any warranty, only trying to reset it back to original state. Please help.
Shadymind said:
Hello friends,
first of all thanks to everyone who supported me to fix my phone.( took me nearly 2 days)
this thread is for the people who bricked their phone while re-branding etcetra and to recover it in easy steps.
First make a note of your IMEI, Product ID, Sno. before proceeding.
1. Download hwota.zip from the link provided.( consist of all oeminfo needed )
https://drive.google.com/open?id=10fNOKja7MD0MOtlPVQH5S9kQ2czdn9dC
2.Unzip to your local c: drive
3.Now download stock firmware of your model or rebranded model number from this website https://www.gizrom.com/huawei-mate-9-stock-rom/
4.after downloading place the files in UNZIPPED FOLDER of HWOTA.ZIP in UPDATE FOLDER.
5.Rename the file as following " update.zip " , " update_all_hw.zip " , update_data_public.zip" . very imp plz.
6.Now open "update.bat"
7.Follow the instructions. You will need your device unlocking code in order to unlock bootloader and install twrp. SO MAKE A NOTE OF YOUR UNLOCK CODE AND SAVE IT.
8.For those your are having trouble finding SNo. and Product id can check from this website or can use HUAWEI PRODUCT ID Generator.
https://imei24.com/warranty_info/Huawei/861956030103197/
9.Now, after following instructions your device will reboot and start factory reset, if it fails then don't worry just hold "power + Vol up " to boot into recovery wipe partition then wipe data (factory reset ) then reboot.
DONE!
10.For those who are having trouble with MEID showing 000000000 don't worry its just for MHA-L09(single sim) showing it as dual sim....but sim works absolutely perfect.
11.For those who want to install oreo they follow same above HWOTA procedure, download official oreo from
https://romprovider.com/2017/11/update-emui-8-0-huawei-mate-9/
That's it!!!!!
If you have any problem installing firmware, feel free to post in this thread, il try to reply asap..:good::good:
GOOD LUCK.
Click to expand...
Click to collapse
hi thank you for the simplified process my question is i have the unlock code but no oem unlock permission and i am unable to move any further is there any solution for it or i am mistaking somewhere
Abody.sy said:
mate 9 mha l29 mha c185b188
I tried to update to oreu the hwota method every thing OK but when phone restart 14% then instillation field!!
the I tried Re-branding method same ( every thing complete ) when phone restart instillation field
the when restart phone say error redownload update again ... no image error n 2
how to recover stuck room!!!
plz help
Click to expand...
Click to collapse
Hi
Have you check the oem info which you had flashed using HWOTA?
Flash the correct oem info for your device and follow instructions in case if it failed again post screenshot of the error.
awais_666 said:
hi thank you for the simplified process my question is i have the unlock code but no oem unlock permission and i am unable to move any further is there any solution for it or i am mistaking somewhere
Click to expand...
Click to collapse
Hi
Apology for late reply, if you got the unlock code try unlocking bootloader using hwota, and continue the process
BUT before proceeding make sure you noted correct unlock code,double check your imei, sno etc if something missing in your unlock code.
Shadymind said:
Hi
Apology for late reply, if you got the unlock code try unlocking bootloader using hwota, and continue the process
BUT before proceeding make sure you noted correct unlock code,double check your imei, sno etc if something missing in your unlock code.
Click to expand...
Click to collapse
no worries dear really appreciate that you are trying to help when i use HWOTA first thing it asks to unlock put the code i have the right code but when i try it using HWOTA it doesnt flash as normally we go to usb debugging and enable it and also click oem unlock to allow device to be unlocked those options are not enabled that is why i cant unlock bootloader
awais_666 said:
no worries dear really appreciate that you are trying to help when i use HWOTA first thing it asks to unlock put the code i have the right code but when i try it using HWOTA it doesnt flash as normally we go to usb debugging and enable it and also click oem unlock to allow device to be unlocked those options are not enabled that is why i cant unlock bootloader
Click to expand...
Click to collapse
Hi,
If it is giving incorrect unlock code then confirm your imei, product id, serial number, get the unlock code from huawei developer page and save it as notepad and try again with hwota....check imei on product box , for some reason after rebranding device gives you some different imei.
Shadymind said:
Hi,
If it is giving incorrect unlock code then confirm your imei, product id, serial number, get the unlock code from huawei developer page and save it as notepad and try again with hwota....check imei on product box , for some reason after rebranding device gives you some different imei.
Click to expand...
Click to collapse
the code is not incorrect and HWOTA doesnt say its incorrect it gets failed to write which is normal for every phone if they dont have it oem unlock enabled from developer options unless there is any other way around
needing file location clarification
QUOTE: 1. Download hwota.zip from the link provided.( consist of all oeminfo needed )
2.Unzip to your local c: drive
3.Now download stock firmware of your model or rebranded
4.after downloading place the files in UNZIPPED FOLDER of HWOTA.ZIP in UPDATE FOLDER.
5.Rename the file as following " update.zip " , " update_all_hw.zip " , update_data_public.zip" . very imp plz.
6.Now open "update.bat"
* I have downloaded ant unzipped HWOTA on pc desktop
* I have downloaded the 3 additional zip files as well.
Do these files go directly into the unzipped HWOTA folder? (you mention UPDATE folder?)
* Do these 3 files stay zipped?
* It doesn't seem to allow me to change the file names
* where is the "update.bat" file to open?
Thank you so very much
Shadymind said:
Hi
Have you check the oem info which you had flashed using HWOTA?
Flash the correct oem info for your device and follow instructions in case if it failed again post screenshot of the error.
Click to expand...
Click to collapse
İ sended the phone to phone engineering shope
the thone successfully start by unknown way for my...
but it installed NRD90M KEYS TEST build nu. android version 7
and some of functions doesn't work
like file manager and theme and Bluetooth...
how to reinstall full room??