Database Info

[Guide] How To Flash Stock Rom Using SP Flash Tool.

Here i am presenting the easy method how to flash stock rom by using SP flash tool
Recommendation :-
1. PC with installed USB Drivers
2. SP Flashtool herehttps://drive.google.com/file/d/0B-0BFYGPDi0YcWpNOE90a216enM/view?usp=sharing
Procedure :-
1. Download And Install USB drivers On Your Computer In Case of Already Installed skip this Step.
2. Power off your android smart phone and remove the battery.
3. download the STOCK ROM and extract on your PC.
4. also extract the SP Flash tool and Open ' Flash Tool exe"
5. Once the Flash tool is Launched click on "download"
6. After click on "scatter loading File" Tab.
7. Locate the "Scatter.txt" location in Which U can extract Your stock rom.
8. NOW,click on "DOWNLOAD" Tab.
9. Connect Your Computer By Using Data cable without battery
10. IN some micromax mobiles Tool will start To download without battery.
BUT, in some mobiles like my KARBONN TITANIUM S5 ULTRA Device Download will start After insert the Battery.
So, please kindly note this step.
11. Congratulation U Can successfully flash your STOCK ROM.
Kip Mind,
[SIZE=''3"] 1. The following steps are works only the stock and custom rom which comes with the scatter file.
2. please, full Backup your Device through stock or custom recovery.
3. This backup will helps to recover your IMEI.
4. In case of lost IMEI Restore previous Backup.
[/SIZE]
Credits:-
shubham shahu .
Hit thankx If u Like my Work :good:

LYF LS-5016 Root [Requires flashign STOCK ROM]

WARNING: Backup your files before flashing!​Part 1​First you need to flash the stock ROM for LS-5016.
Stock ROM and USB Qualcomm driver : https://drive.google.com/uc?id=0B1hm-6TNn10IclpwN2J0cXdLTU0&export=download
Don't use the QPST present in the zip file, instead download and install from the link given below.
QPST : https://androiddatahost.com/flkn2
Steps to flash
1- Download QPST tool.
2- Install Qualcomm driver.
3- Run QPST tool.
4- Add new port (Check device manager)
5. Select Flat Build.
6- Click browse on Select Programmer and search for prog_emmc_firehose_8909_ddr.mbn in the Stock ROM folder.
7- Click Load XML and double click on rawprogram_unsparse.xml and select patch0.xml.
8- Select Download and wait for the flashing to be finish.
---------------------------------------------------------------------------------------------------------------------------------------------------------------
NOTE​If you can't get any mobile signal after flashing, that means there is no IMEI on your phone. You can add IMEI with this software.
IMEI : https://drive.google.com/file/d/0B0ELQ1N9_LSZTC1uV3RzOF9YN0E/view?pageId=108278839868431761759
1. Write down the 2 IMEI numbers.
2. Unlock developer options and unlock OEM and USB debugging.
3. Connect your phone with you PC and use the software and reboot.
---------------------------------------------------------------------------------------------------------------------------------------------------------------
Part 2​
1. Download Kingoroot and root your device.
2. If you want to change to SuperSU then follow the instructions from this forum. Use SuperSU 2.79.
https://forum.xda-developers.com/android/software-hacking/replace-kingoroot-supersu-manually-t3573361
NOTE​Don't update your device at all. Disable Wireless Update app from Settings - Apps
IF YOU HAVE ANY PROBLEMS OR QUESTIONS I WOULD BE HAPPY TO HELP YOU.​

QFIL Sahara fail on the version you linked. Had to use 1.0.0.2
Half screen issue with the rom.

No service after flashing
Can you please provide qcn file

[STOCK][UB][PIE] Install stock pie on unlocked x4 form android 8.0

Code:
All information and files — both in source and compiled form — are provided on an as is basis.
No guarantees or warranties are given or implied. The user assumes all risks of any damages
that may occur, including but not limited to loss of data, damages to hardware, or loss of
business profits. Please use at your own risk. Note that unless explicitly allowed by the warranty
covering your device, it should be assumed that any warranty accompanying your device will
be voided if you tamper with either the system software or the hardware.
1. Preparing for the flash:
1. DELETE all of your fingerprints and remove any screeenlock
2. Make a Nandroid backup in TWRP
3. Download Firmware from: https://moto.netlib.re/payton/PAYTON_PPW29.69-26_subsidy-DEFAULT_regulatory-DEFAULT_CFC.xml.zip
4. Unzip the downloaded file.
2. Flashing
1. Make sure that you phone is charged (at least 60%)
2. Download flash.sh HERE
3. Linux: chmod +x flash.sh
4. connect x4 to your pc and run : adb reboot bootloader
5. run: ./flash.sh
6. Reboot
3. Magisk
1. Download twrp-***.img
2. Download Magisk18.0 to your phone or pc
3. run: fastboot boot twrp-***.img
4. flash magisk in twrp
5. reboot
4. After install
- you can now add you fingerprints back and set up a screenlock
NOTE:
1. First boot will take longer
2. There will be a black line on your blue moto logo

is this android one pie?
link for firmware file is broken.

Can you please fix the first link? Also can this apply to my Moto X4 with android 8.1?

munchy_cool said:
is this android one pie?
link for firmware file is broken.
Click to expand...
Click to collapse
No it isn't android one.

patrick8996 said:
Can you please fix the first link? Also can this apply to my Moto X4 with android 8.1?
Click to expand...
Click to collapse
You probably can. But a am not certain about it. If you are on 8.1 download the 1.1GB file from post about upgrading from 8.1 with looked bootloader and extract files from payload.bin.

[GUIDE] How to unbrick Realme Narzo 30 pro 5G or equivalent

* I am not responsible for bricked devices, dead SD cards. You are choosing to follow this thread, and you are responsible for any mess !​Requirements:
- Windows 8.1 or above 64-bit with Admin rights (Windows 10 64 bit recommended)
- Python Installed
- Original USB Cable provided by Realme
- At least 10GB of internet
Steps:
1. Download the tools attached below
2. In Driver/cdc-acm folder you will find cdc-acm.inf, right click and install it (You need to disable core isolation from windows security settings, if enabled)
3. Install libusb-win32-devel-filter-1.2.6.0.exe
4. Open libusb-filter-tool
5. Connect your device to your pc while pressing and holding volume up, volume down button together
6. You will see Mediatek USB PORT (COM X), select and install it and disconnect your device (Switch off your device in case, it turned on)
7. Now extract the firmware (which is in zip file), you will see a .ofp in the extracted files, use oppo_decrypter tool (link below) to extract the ofp file
8. Open SP Flash tool which is provided below and select MT6853 Scatter from wherever you extracted the ofp file, after that you need to uncheck opporeserve, special_preload, my_custom, cdt engineering
9. (USE Download only option) click on download button
10. Open MTKMETAUtility.exe and select Disable Auth
11. Connect your phone in the same USB port and with same method as above
12. SP Flash Tool should start flashing the device, after the flashing is done, disconnect and press power-button for 10+ secs to reboot, it will reboot into recovery
13. Make sure to Format Data (Yes, not wipe data, use FORMAT DATA), it should reboot automatically after you will press ok
14. Done !!!!
Downloads:
-Drivers (CSC-acm and libusb-win32-devel-filter)
-MTKMETAUTILITY
-Python
-Firmware (Realme Narzo 30 pro 5G) (Android 10)
-oppo_decrypt_tool

Is there a video version or an updated version of this tutorial? I'm with my Q2 (rmx2117) brick

the touch is not working in recovery mode

MTKMETAUTALITY is not working

AK_8K said:
MTKMETAUTALITY is not working
Click to expand...
Click to collapse
Try this one: MTK META UTILITITY: Mega

XeeXa said:
Is there a video version or an updated version of this tutorial? I'm with my Q2 (rmx2117) brick
Click to expand...
Click to collapse
You can follow these steps but try using the chinese firmware (Realme Q2), Sorry, I do not have any video tutorial for this.

How To Guide How to downgrade rmx3560/3561 and flash India version rom (for Android 13)

I realized that updating version to Android 13 realme ui 4.0 using image flash method will cause brick even hardbrick, downgrading ota to Android 12 version really isn't safe anymore . The main cause is due to the bootloader version of android 13. In this post I will show everyone how to downgrade to Android 12 and make rom transfer from rmx3560 to india version rmx3561
The article I have detailed and easy to understand is pinned by my group
How to downgrade Android 13 (realme ui 4.0) to Android 12 (realme ui 3.0):
STEP 1
1. Download app OPLU see link (I am not authorized to post links here. Instead the app name OPLocalUpdate_For_Android 12)
2. Download the roll back package in your phone and remember the location (leave it out of main memory, not contained in any directory)
3. Open app OPLU - select the setting icon in the top right corner - You will see the downgrade file there - Click select package and click update (it will say wipe all data after update)
4. After restarting the phone, the phone is set up normally, but please download the OPLU application again and download the update package (usually I download the downgrade package, I usually copy it to my computer).
5. Repeat the downgrade operation but still use the downgrade package you just used - Wait for 100% progress and the phone will factory reset one more time.
STEP 2:
Advanced downgrade: required unlocked Bootloader
1. After doing the 5 steps I mentioned above, find the OTA file (zip file that contains payload.bin) of your device and download it to your computer and remember the location.
2. Download Fastboot enhance from github source
3. Plug your phone into the computer - Boot the phone into fastbootd with the command: adb reboot fastboot
4. You will see an interface with China language - you choose English and it must be Fastbootd
5. From the computer screen open Fastboot enhance - you will see on it display the serial number of devices
6. Extract the downloaded OTA file and on the Fastboot enhance screen select flash payload.bin.
–> Wait for the green progress bar to run to 100% then success.
8. On the phone screen we select "wipe data" - Enter the wipe code - Select yes
9. Wait for the phone to reboot => Successful downgrade
(You can use this to flash other firmware)
#Tumodpro
If you have any questions, don't hesitate to message me.

TuLy2702 said:
The article I have detailed and easy to understand is pinned at the following link: Mod edit: TG link removed
If you have any questions, don't hesitate to message me. I will support you all the time.
Click to expand...
Click to collapse
While we appreciate you wanting to share your guide, we would prefer that you share it on XDA rather than directing members to an off site location that requires registration. Thank you.
-Regards: Badger50

So this method only work for ubl device?

can i put Rom from other regions?

Hey bro how you doing, can you make a youtube video instead of writing and send us the link would appreciate it.