Database Info

[Guide] How to Root Leagoo Leagoo KIICAA Mix

Guys This is the Guide to Root Leagoo KIICAA Mix-
Download Require Files-
1. Download SP flash tools https://androidfilehost.com/?fid=745425885120763929
2. V Com Driver Require https://androidfilehost.com/?fid=817550096634801170
3. twrp Require https://romprovider.com/2017/10/t-root-leagoo-kiicaa-mix/
4. Supersu Require https://forum.xda-developers.com/apps/supersu/v2-64-2-66-supersu-mode-t3286120
Instructions-
1. Install VCom Driver
2. Run SP flash tools and Load scatter from Recovery folder
3. check recovery only and under recovery section load twrp.img
4. click Download, and connect switched off Phone to PC
5. wait for success. Done twrp installed.
6. reboot to twrp by holding power and volume+ button
7. create a nandroid backup
8. flash supersu.zip, done successfully Rooted.
i hope You will get success.

which button(s) shoud i press on the installer?
when i press on the installer i have a lot of buttons(install miracle,install spd etc)
which i shoud i press?
and will it work on windows 7?
thanks

Hey there!
I would like to root this using a linux desktop, could you explain the process in more detail which tool is responsible for which function so I could try to adapt the process to function without a windows desktop?

kaefert said:
Hey there!
I would like to root this using a linux desktop, could you explain the process in more detail which tool is responsible for which function so I could try to adapt the process to function without a windows desktop?
Click to expand...
Click to collapse
Hi,
if you are running a debian based distro, you have first to install adb and fastboot from manager or using apt-get.
2/ check if file /etc/udev/rules.d/51-android.rules is present and contains correct description of your phone idVendor and idProduct
if not run lsusb and add the following line
Code:
SUBSYSTEMS=="usb", ATTRS{idVendor}=="your idVendor", ATTRS{idProduct}=="your idProduct", MODE="0666" GROUP="androiddev", SYMLINK+="android%n"
3/ service udev restart
4/ unplug and plug again your phone and run adb devices, it will show a long number and letters with UNAUTHORIZED. that's OK
5/enter fastboot mode and unlock your bootloader with : fastboot oem unlock
6/ enter fastboot mode when booting your phone and type this: fastboot flash recovery recovery.img
( you have to rename twrp.img to recovery.img)
that's done you can now boot to twrp and install su.

hey there avrmge!
thanks for the reply, but I already sent the device back to the seller, it was too far below my expectations.

kaefert said:
hey there avrmge!
thanks for the reply, but I already sent the device back to the seller, it was too far below my expectations.
Click to expand...
Click to collapse
Hello,
the procedure above generally works with any other android device,
i think the main problem with this phone is lack of notification led, no 3.5mm jack and sometimes battery drains too fast. except that, it is as normal as other models in same segment. what were your expectations ?

well, I was disappointed with the problems you mentioned and also:
-) no light sensor ( --> no automatic brightness)
-) accelerometer has only 2 axis working
-) no gyroscope
-) no proximity sensor

boot loop after root ! Ur guide to the hell

mark332 said:
Guys This is the Guide to Root Leagoo KIICAA Mix-
Download Require Files-
1. Download SP flash tools https://androidfilehost.com/?fid=745425885120763929
2. V Com Driver Require https://androidfilehost.com/?fid=817550096634801170
3. twrp Require https://romprovider.com/2017/10/t-root-leagoo-kiicaa-mix/
4. Supersu Require https://forum.xda-developers.com/apps/supersu/v2-64-2-66-supersu-mode-t3286120
Instructions-
1. Install VCom Driver
2. Run SP flash tools and Load scatter from Recovery folder
3. check recovery only and under recovery section load twrp.img
4. click Download, and connect switched off Phone to PC
5. wait for success. Done twrp installed.
6. reboot to twrp by holding power and volume+ button
7. create a nandroid backup
8. flash supersu.zip, done successfully Rooted.
i hope You will get success.
Click to expand...
Click to collapse
I need help, when i try to install the vcom drivers, i get an error. i can,t post image so...

can you add video?

how to imei change?

Maybe it's not the place but is there someone who get complain on that the speaker is so low can I increase it and make it louder cause people say we can't here you please help

mark332 said:
Guys This is the Guide to Root Leagoo KIICAA Mix-
Download Require Files-
1. Download SP flash tools https://androidfilehost.com/?fid=745425885120763929
2. V Com Driver Require https://androidfilehost.com/?fid=817550096634801170
3. twrp Require https://romprovider.com/2017/10/t-root-leagoo-kiicaa-mix/
4. Supersu Require https://forum.xda-developers.com/apps/supersu/v2-64-2-66-supersu-mode-t3286120
Instructions-
1. Install VCom Driver
2. Run SP flash tools and Load scatter from Recovery folder
3. check recovery only and under recovery section load twrp.img
4. click Download, and connect switched off Phone to PC
5. wait for success. Done twrp installed.
6. reboot to twrp by holding power and volume+ button
7. create a nandroid backup
8. flash supersu.zip, done successfully Rooted.
i hope You will get success.
Click to expand...
Click to collapse
I am having problems with twrp when installing and starting in recovery mode it freezes me forcing to restart the device

mark332 said:
Guys This is the Guide to Root Leagoo KIICAA Mix-
Download Require Files-
1. Download SP flash tools https://androidfilehost.com/?fid=745425885120763929
2. V Com Driver Require https://androidfilehost.com/?fid=817550096634801170
3. twrp Require https://romprovider.com/2017/10/t-root-leagoo-kiicaa-mix/
4. Supersu Require https://forum.xda-developers.com/apps/supersu/v2-64-2-66-supersu-mode-t3286120
Instructions-
1. Install VCom Driver
2. Run SP flash tools and Load scatter from Recovery folder
3. check recovery only and under recovery section load twrp.img
4. click Download, and connect switched off Phone to PC
5. wait for success. Done twrp installed.
6. reboot to twrp by holding power and volume+ button
7. create a nandroid backup
8. flash supersu.zip, done successfully Rooted.
i hope You will get success.
Click to expand...
Click to collapse
when i open twrp, it asks for a password. my phone doesn't have any password, and i need it to install a custom rom. is there someone able to help me? bc i really can't understand
*im assuming that i have to unlock oem, but is it really necessary?

Ciao, ho installato la twrp tutto a posto, poi ho messo pixel 1.2 rom, ma audio in telefonata pessimo mi serve un aiuto per migliorare grazie

I installed a proper twrp (fastboot flash)
Leagoo KIICAA Mix 3.1
MediaFire is a simple to use free service that lets you put all your photos, documents, music, and video in a single place so you can access them anywhere and share them everywhere.
www.mediafire.com

[Guide] Flash stock firmware ( rom ) to Nokia 7 plus ( TA-1046 )

Warning :- I am not responsible for any kind of your device damage like soft or
hard brick . DO IT OWN YOUR RISK
Pre- requirements ?
1. Bootloader unlocked
2. Pc / laptop with windows operating system
3. Patience
Tool required
1. OST 6.0.4
https://drive.google.com/open?id=1n91aYT9Di6_v4F3Wjlv8TjfeLc64AcYA
2. Notepad ++
https://notepad-plus-plus.org/download/v7.6.6.html
3. Winrar
https://www.rarlab.com/download.htm
4. Platform tool
https://developer.android.com/studio/releases/platform-tools
5. Nokia driver
https://github.com/StollD/nokia-driver-installer/raw/master/out/Phone_Nokia_USB_Driver_v1.4.0.exe
6. nb0 unpaker
https://forum.xda-developers.com/android/general/nb0-unpacker-packer-tool-t3699464
7. Firmware file ( Oreo 8.1 )
https://fih-firmware.hikaricalyx.com/hmd_en.html#b2n
Steps of flashing
1. Download all files from the link given
2. Extract the file B2N...... .nb0.7z/zip using
winrar
3. Then extract B2N.... .nb0 file using nb0
unpacker
4. Find .mlf file in extracted files and edit in Notepad as the value given below ?
INITOPTION = 0x20000
INITDLTYPE = 0x60
SECURITY_VER = 0x0001
And save the file
5. Run ost tool on your pc/ laptop
6. Select .mlf file on ost tool
7. Reboot your device to download mode
and connect to PC/laptop
8. Flash and wait for boot up
Note :- The process will take time
For other processes follow other guide???

Purak6 said:
Warning :- I am not responsible for any kind of your device damage like soft or
hard brick . DO IT OWN YOUR RISK
Pre- requirements
1. Bootloader unlocked
Note :- The process will take time
For other processes follow other guide
Click to expand...
Click to collapse
any method for locked devices with Developer Preview 4 running

AlahmadPR said:
any method for locked devices with Developer Preview 4 running
Click to expand...
Click to collapse
You can flash latest rom ( march full rom zip pie )

Dear users, I have a Nokia 7 plus updated to the latest fw (android 10 I guess). Because of full memory or because something else the OS doesn't start. It appears a mini recovery where It's written "impossible load the android system. Your data could be damaged.....and so on.... I have just two options:
1) Retry (obviously this option doesn't work)
2) Restore factory settings
I've some data important data inside the phone and I'd like to recover them.
Unfortunately I've never modified the recovery so I guess I've also a locked bootloader, so the TWRP isn't an option. I was thinking about download the original FW and to reinstall it Via ADB. Usually I used this method with samsung through ODIN and often it worked.
Could it works for your opinions?
Thanks for your help,
waiting for your response

Teclast T30 T1P2 Root

Actual Firmware https://onedrive.live.com/?authkey=!APMSxpd_UoEEQBY&id=A120532B51026BDA!1816&cid=A120532B51026BDA
Unlock Bootloader https://rootwrp.com/unlock-teclast-t20-bootloader/
and flash with
fatboot flash boot +file
https://forum.xda-developers.com/apps/magisk/official-magisk-v7-universal-systemless-t3473445

This is for the new teclast t30 tablet? can you make a video?

Yes Brand New
https://www.youtube.com/watch?v=G4uuLCjBWrs&feature=youtu.be
Video is About Patch/flashing Bootimage with Magisk Manager(Tablet is already rooted)

hello
successfully root new T30 with patched boot.img (with magisk).
I have unlocked bootloader with "fastboot flashing unlock" but now, have a message on boot screen and have to wait 5s more for boot
is there any way to bypass this message and 5s pause ?
there is a TWRP 3.3.1 on 4pda by nemo-nemo and helpers, but touchscreen don't work for me

Unlocked Bootloader cause this warning on Boot(Power Button should override the 5 secs Pause)
Dont using the recovery i dont know

Here is TWRP 3.3.1 for T1P2 (T30):
https://drive.google.com/file/d/1RW5ek_FIAMe_8KvRWpNE_l7wi8qNxmUS/view?usp=sharing
Thx to nemo-nemo on 4pda.ru

Hello,
I can confirm TWRP work fine but you have to use a USB-OTG mouse
The 1st time you boot on TWRP, you have a encryption code request, choose "cancel"
To disable force encryption, flash "DisableForceEncryption_treble" zip with TWRP
When you unlock bootloader of this T30, you have warning message and 5s wait to boot
There is a tweak to bypass this:
download script "orange_state_disabler" zip and flash it with TWRP
this script is fully safe, there is a compatibility test and don't flash if it can't.
Thx to XopmoH97 from 4pda.ru
Download from here: https://drive.google.com/drive/folders/1tSInU_vOFZAfpdbc1bETAuIJsniQqjUd?usp=sharing

edit*

TechGuru123 said:
there is a newer firmware for this tablet
T30(T1P1)_Android 9.0_V1.04_E43D.rar
https://pan.baidu.com/s/1sjEt1jxEOz...arentPath=/sharelink491465238-972273915700760
password
1f9r
Click to expand...
Click to collapse
What's your source ?
Have you verify this firmware ?
T30 is T1P2, not T1P1.
Look at your ID on tablet's backside: T1P2
Go to Teclast website firmware and search for
T1P1: unknown
T1P2 -> T30
Verify and test before publish, please

edit*

My PC can't find any T30 fastboot devices... which drivers use ??

Search for "MTK_USB_All_v1.0.8" on google

Is there no way to root without unlocking the bootloader first?

kestrelv2 said:
Is there no way to root without unlocking the bootloader first?
Click to expand...
Click to collapse
Unlocking bootloader is useless for 90% of users
Why ?:
- Only for fastboot commands
- Unlocking bootloader avoid warranty
You can do lot of things without unlock:
- Install TWRP (with Upgradetool)
- Install custom system, logo, boot, etc ... with upgradetool
and
You can root without unlock:
- Download firmware (T1P2) from teclast website and unpack in PC folder, ex: "T30_firm".
- Download and install "MTK_USB_All_v1.0.8" for MTK drivers (search on google)
- Connect your T30 to PC with usb
- In "T30_firm/firmware" folder, copy "boot-verified.img" to you T30
- Install magisk manager on your T30 an launch it
- Choose install magisk by "patch a file", choose your "boot-verified.img" and wait
- Now, you have a "magisk-patched.img" file in download folder
- Copy "magisk-patched.img" on your "T30_firm" folder PC
- Launch "Upgrade tools.exe" in "T30_firm/upgrade tool" folder
- Unselect all "img" files
- Select only "boot" line and choose your "magisk-patched.img" (click on same line, "location" column)
- Shutdown your T30 (allways connected to pc)
- Clic on "download" in upgrade tool and wait for big popup with green "V"
You can disconnect you T30 and boot.
Open magisk manager, "tada !" magisk is ready

murigny64 said:
Unlocking bootloader is useless for 90% of users
Why ?:
- Only for fastboot commands
- Unlocking bootloader avoid warranty
You can do lot of things without unlock:
- Install TWRP (with Upgradetool)
- Install custom system, logo, boot, etc ... with upgradetool
and
You can root without unlock:
- Download firmware (T1P2) from teclast website and unpack in PC folder, ex: "T30_firm".
- Download and install "MTK_USB_All_v1.0.8" for MTK drivers (search on google)
- Connect your T30 to PC with usb
- In "T30_firm/firmware" folder, copy "boot-verified.img" to you T30
- Install magisk manager on your T30 an launch it
- Choose install magisk by "patch a file", choose your "boot-verified.img" and wait
- Now, you have a "magisk-patched.img" file in download folder
- Copy "magisk-patched.img" on your "T30_firm" folder PC
- Launch "Upgrade tools.exe" in "T30_firm/upgrade tool" folder
- Unselect all "img" files
- Select only "boot" line and choose your "magisk-patched.img" (click on same line, "location" column)
- Shutdown your T30 (allways connected to pc)
- Clic on "download" in upgrade tool and wait for big popup with green "V"
You can disconnect you T30 and boot.
Open magisk manager, "tada !" magisk is ready
Click to expand...
Click to collapse
Ill give it a try thanks.
It worked, thanks a bunch!!!

When I turn off the T30 and press download, nothing happens anymore. I tried it on both Windows 7 and Windows 10. Just nothing. I'm waiting 10 minutes, then I'll put a stop and i'm done. No change. Does the tablet really have to turn off? Otherwise it's very well described, I think I'm making a mistake somewhere, I just don't know where.
Zuzzana

Try press "download" first and then, power off

zuzzana said:
When I turn off the T30 and press download, nothing happens anymore. I tried it on both Windows 7 and Windows 10. Just nothing. I'm waiting 10 minutes, then I'll put a stop and i'm done. No change. Does the tablet really have to turn off? Otherwise it's very well described, I think I'm making a mistake somewhere, I just don't know where.
Zuzzana
Click to expand...
Click to collapse
For me these mtk tools only do anything when i plug into a certain usb port. I couldnt find one that worked on my desktop pc but on my laptop its the usb 2.0 slot that worked and not either of the usb 3 slots. Turn it off click download and then plug in the tablet and it should start assuming you have properly installed the needed drivers.

Thank you, thank you, thank you. It just wanted to press download first and then plug it into USB. Thanks again.
Zuzzana

WARNING !!
Don't flash chinese firmware mentioned above by @TechGuru123
This firmware erase all your partitions,your NVRAM and IMEI
You will lose IMEI and it's hard to recover !

Question [Guide] How to use SP Flash tool [Windows Only!]

Today I'm going to write how to use so flash tool for OnePlus Nord CE 2
Before you begin download: https://drive.google.com/file/d/1fL8qqu_pBK1YU5xbgugLax7ZKU-k3ex7/view?usp=drivesdk
This includes sp flash tool for our MTK version, drivers and MTK Bypass files!
Requirements: PC or Laptop
Internet connection
USB cable
Take a backup of your data, Just in case if any error happens.
Windows Method
Requirements:
SP_Flash_Tool_5.2112.00.zip
drive.google.com
Decrypted OFP for our device! You can find it on Google!
Install Python from Windows Store
https://sourceforge.net/projects/li...ibusb-win32-devel-filter-1.2.6.0.exe/download
libusb-win32 - Having Issues? Click Here
Steps:
1) Extract the zip
2) Use the bundled QcomMtk_Driver_Setup_3.1.9.exe from the zip. for MTK Preloader USB VCOM driver it should be installed within windows 8 and above?
3)Download this file and install it, after installing power off phone and connect to pc while holding Vol+- (don't leave the buttons after connecting) . You might need this driver as well if it's not detected.
Press next, connect your device to PC while holding Vol+- buttons (your device needs to be powered off, and don't leave the buttons) and you will see the mtkdriver down below. Install it.
Choose MediaTek USB Port and install it.
4)Then run the brom.bat under Bypass folder (spflashtool/mtk-bypass/bypass). (for Linux, When available) use command: python3 mtk payload to start the BROM exploit!
5) Now power off the phone and connect the phone while holding volume + and - (Don't leave the buttons until the bypass is done)
6)After the above step Go into Flash Tool folder and open the SPFlash tool and launch flash_tool.exe
7) Click on Options>Options and go to Connections and select UART and set Baud Rate to 921600
8)Now in Sp flash tool select the scatter file which you have extracted from Partitions.zip and make sure that prealoder, lk, and lk2 is selected.
9) You don't need to select auth file as authorization is disabled. Once you do it, it should look like this. ALWAYS MAKE SURE DOWNLOAD ONLY MODE IS SELECTED! DON'T SELECT OTHER MODES!
Make SURE "Download Only" is selected. Don't select ANYTHING ELSE! You will lose your IMEIs, Serial Numbers, Capability of Hardware Attestation etc. if you choose "Format data + Download" make SURE you selected "Download Only".
10) Now, you can start downloading with the button and after that a checkmark will appear. You can reboot your phone
After flashing it should look like this. Download has been complete.
Credits:
B. Kerler for MTK Bypass
@Saksham Antil (aka Tony Stark) for original guide

Reserved for updates:
When Linux Version will be available for our devices it will be posted
Edit it looks like it is, only my who uses old source

[ GSI ] Flashing Guide MTK [ Works for IMEI erased phones too ! ] [ RMX2117 used to demonstrate]

Note: Device must be project treble supported
Spoiler: Jump to flashing
Before proceeding check if your device is project treble supported using treble check app. We will be flashing Evolution X GSI by ponces on Realme Narzo 30 Pro [RMX2117] using SP Flash Tool
Note: Device must be on Android 11 if you are using the super from the files uploaded
Steps:
Open MTKClient GUI 2.0 folder and run Bypass.exe, select option 3- Bypass SLA / DAA by using down arrow key and press enter.
It will ask do you want to continue?, type y and press enter
Tool will be waiting for device to connect
Switch off your phone
Hold volume up and volume down together and connect phone to PC with USB cable
Tool will detect the phone and start the bypass process
Once completed, keep the phone connected
Open SP Flash tool by double clicking flash_tool.exe and choose download only option from drop down menu
Choose Download-Agent option on right side and choose MTK_AllInOne_DA.bin file from SP Flash Tool folder
Choose Scatter-loading File MT6853_Android_scatter.txt from Stock ROM with GSI folder
Choose Authentication File auth_sv5.auth from Stock ROM with GSI folder
Now all partitons of your device will be listed within the tool
Scroll down until you see super.img , now check the only box on left of super
Click on right of super to select location where our custom built super with Evolution X GSI is stored
Click on Download
Once the flashing is complete, there will be a prompt with green tick
Disconnect your phone
Your device has GSI flashed now ╰(*°▽°*)╯
This method is for mediatek chipset devices only
Disclaimer:
This guide does not include the normal process of flashing GSI using DSU ( Dynamic System Update ), you can learn more about that here. By using this method, you can’t use both stock rom along with GSI, you will be flashing a modified super.img. There is a risk of bricking your device and causing irreversible damage to it if not done correctly. This guide also works for devices with IMEI erased due to reason such as ( formatting all partitions while flashing )
Before doing any modifications it is important to have a backup which can be used if something goes wrong. Follow this guide to know how to backup all partitions which can be flashed to recover your device
Flashing GSI includes potential risk of bricking the device because of modifying critical partitions, it is recommended to take backup before proceeding
If you are not familiar to flashing files to your phone, do not worry we will learn along the guide
Flashing GSI:
Prerequisite:
1. Mediatek drivers- Download here
2. Python- Download here | Git- Download here
3. Unlocked bootloader- steps mentioned below
4. MTK Client GUI- Download here
5. SP Flash Tool- Download here
6. Stock ROM with custom super- Download here [ Only for Narzo 30 pro ] [ RMX2117 ]
Guide for making custom super for other devices will be uploaded soon​
Setup:
1. Mediatek drivers
Extract the zip and run the exe file, after the installation process is complete restart your PC
If your device still isn't detected, install drivers manually with help of this guide
After the installation process is complete, restart your PC
2. Python | Git
Go to python directory
Search python in start menu, right click python and click on open file location, again right click on python and click open file location | This is the python directory.
Type cmd inside the address bar of file explorer and press Enter
Inside command prompt windows exectue following commands one by one
Thanks Bjoern Kerler
git clone https://github.com/bkerler/mtkclient
cd mtkclient
pip3 install -r requirements.txt
3. Unlocked Bootloader [ User data will be formatted ]
Turn off your phone
Open python directory and open mtkclient folder inside it
Type cmd inside the address bar of file explorer and press Enter
Now run below command
python mtk e metadata,userdata,md_udc
Connect phone to PC with USB Cable while holding Vol+ and Vol- together
Now run below commands one by one
python mtk da seccfg unlock
python mtk reset
After the script completes, disconnect phone and reboot by holding power button
Your device's bootloader is unlcoked now ╰(*°▽°*)╯
4. MTK Client GUI [ Use this tool carefully, don’t click on something if you don’t know what you are doing ]
Open MTK Client GUI 2.0 folder and install UsbDk_1.0.22_x64.msi
5. SP Flash Tool [ Use this tool carefully, never tick Format All + Download option, that will format all partitions which can erase partitions containing IMEI too! ]
Custom Super.img
Super.img consist of various partition on your device eg: system, vendor, product, odm, etc
This custom super.img, replaces a partition – system | The stock system image is replaced with system image of GSI
You can make your own custom super.img and flash it on your device and try different GSI
Steps for doing this will be updated in near future
Now comes actual flashing part:
Before proceeding check if your device is project treble supported using treble check app. We will be flashing Evolution X GSI by ponces on Realme Narzo 30 Pro [RMX2117] using SP Flash Tool
Note: Device must be on Android 11 if you are using the super from the files uploaded
Steps:
Open MTKClient GUI 2.0 folder and run Bypass.exe, select option 3- Bypass SLA / DAA by using down arrow key and press enter.
It will ask do you want to continue?, type y and press enter
Tool will be waiting for device to connect
Switch off your phone
Hold volume up and volume down together and connect phone to PC with USB cable
Tool will detect the phone and start the bypass process
Once completed, keep the phone connected
Open SP Flash tool by double clicking flash_tool.exe and choose download only option from drop down menu
Choose Download-Agent option on right side and choose MTK_AllInOne_DA.bin file from SP Flash Tool folder
Choose Scatter-loading File MT6853_Android_scatter.txt from Stock ROM with GSI folder
Choose Authentication File auth_sv5.auth from Stock ROM with GSI folder
Now all partitons of your device will be listed within the tool
Scroll down until you see super.img , now check the only box on left of super
Click on right of super to select location where our custom built super with Evolution X GSI is stored
Click on Download
Once the flashing is complete, there will be a prompt with green tick
Disconnect your phone
Your device has GSI flashed now ╰(*°▽°*)╯
Since GSI is not built for the device you are flashing on specifically, it has bugs or they lack the ability of customizing it for every device but there are fixes too!
GSI fixes/patches/mods for RMX2117 will be uploaded in near future
Screenshots:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}

NinjaChunks said:
Note: Device must be project treble supported
Spoiler: Jump to flashing
Before proceeding check if your device is project treble supported using treble check app. We will be flashing Evolution X GSI by ponces on Realme Narzo 30 Pro [RMX2117] using SP Flash Tool
Note: Device must be on Android 11 if you are using the super from the files uploaded
Steps:
Open MTKClient GUI 2.0 folder and run Bypass.exe, select option 3- Bypass SLA / DAA by using down arrow key and press enter.
It will ask do you want to continue?, type y and press enter
Tool will be waiting for device to connect
Switch off your phone
Hold volume up and volume down together and connect phone to PC with USB cable
Tool will detect the phone and start the bypass process
Once completed, keep the phone connected
Open SP Flash tool by double clicking flash_tool.exe and choose download only option from drop down menu
Choose Download-Agent option on right side and choose MTK_AllInOne_DA.bin file from SP Flash Tool folder
Choose Scatter-loading File MT6853_Android_scatter.txt from Stock ROM with GSI folder
Choose Authentication File auth_sv5.auth from Stock ROM with GSI folder
Now all partitons of your device will be listed within the tool
Scroll down until you see super.img , now check the only box on left of super
Click on right of super to select location where our custom built super with Evolution X GSI is stored
Click on Download
Once the flashing is complete, there will be a prompt with green tick
Disconnect your phone
Your device has GSI flashed now ╰(*°▽°*)╯
This method is for mediatek chipset devices only
Disclaimer:
This guide does not include the normal process of flashing GSI using DSU ( Dynamic System Update ), you can learn more about that here. By using this method, you can’t use both stock rom along with GSI, you will be flashing a modified super.img. There is a risk of bricking your device and causing irreversible damage to it if not done correctly. This guide also works for devices with IMEI erased due to reason such as ( formatting all partitions while flashing )
Before doing any modifications it is important to have a backup which can be used if something goes wrong. Follow this guide to know how to backup all partitions which can be flashed to recover your device
Flashing GSI includes potential risk of bricking the device because of modifying critical partitions, it is recommended to take backup before proceeding
If you are not familiar to flashing files to your phone, do not worry we will learn along the guide
Flashing GSI:
Prerequisite:
1. Mediatek drivers- Download here
2. Python- Download here | Git- Download here
3. Unlocked bootloader- steps mentioned below
4. MTK Client GUI- Download here
5. SP Flash Tool- Download here
6. Stock ROM with custom super- Download here [ Only for Narzo 30 pro ] [ RMX2117 ]
Guide for making custom super for other devices will be uploaded soon​
Setup:
1. Mediatek drivers
Extract the zip and run the exe file, after the installation process is complete restart your PC
If your device still isn't detected, install drivers manually with help of this guide
After the installation process is complete, restart your PC
2. Python | Git
Go to python directory
Search python in start menu, right click python and click on open file location, again right click on python and click open file location | This is the python directory.
Type cmd inside the address bar of file explorer and press Enter
Inside command prompt windows exectue following commands one by one
Thanks Bjoern Kerler
git clone https://github.com/bkerler/mtkclient
cd mtkclient
pip3 install -r requirements.txt
3. Unlocked Bootloader [ User data will be formatted ]
Turn off your phone
Open python directory and open mtkclient folder inside it
Type cmd inside the address bar of file explorer and press Enter
Now run below command
python mtk e metadata,userdata,md_udc
Connect phone to PC with USB Cable while holding Vol+ and Vol- together
Now run below commands one by one
python mtk da seccfg unlock
python mtk reset
After the script completes, disconnect phone and reboot by holding power button
Your device's bootloader is unlcoked now ╰(*°▽°*)╯
4. MTK Client GUI [ Use this tool carefully, don’t click on something if you don’t know what you are doing ]
Open MTK Client GUI 2.0 folder and install UsbDk_1.0.22_x64.msi
5. SP Flash Tool [ Use this tool carefully, never tick Format All + Download option, that will format all partitions which can erase partitions containing IMEI too! ]
Custom Super.img
Super.img consist of various partition on your device eg: system, vendor, product, odm, etc
This custom super.img, replaces a partition – system | The stock system image is replaced with system image of GSI
You can make your own custom super.img and flash it on your device and try different GSI
Steps for doing this will be updated in near future
Now comes actual flashing part:
Before proceeding check if your device is project treble supported using treble check app. We will be flashing Evolution X GSI by ponces on Realme Narzo 30 Pro [RMX2117] using SP Flash Tool
Note: Device must be on Android 11 if you are using the super from the files uploaded
Steps:
Open MTKClient GUI 2.0 folder and run Bypass.exe, select option 3- Bypass SLA / DAA by using down arrow key and press enter.
It will ask do you want to continue?, type y and press enter
Tool will be waiting for device to connect
Switch off your phone
Hold volume up and volume down together and connect phone to PC with USB cable
Tool will detect the phone and start the bypass process
Once completed, keep the phone connected
Open SP Flash tool by double clicking flash_tool.exe and choose download only option from drop down menu
Choose Download-Agent option on right side and choose MTK_AllInOne_DA.bin file from SP Flash Tool folder
Choose Scatter-loading File MT6853_Android_scatter.txt from Stock ROM with GSI folder
Choose Authentication File auth_sv5.auth from Stock ROM with GSI folder
Now all partitons of your device will be listed within the tool
Scroll down until you see super.img , now check the only box on left of super
Click on right of super to select location where our custom built super with Evolution X GSI is stored
Click on Download
Once the flashing is complete, there will be a prompt with green tick
Disconnect your phone
Your device has GSI flashed now ╰(*°▽°*)╯
Since GSI is not built for the device you are flashing on specifically, it has bugs or they lack the ability of customizing it for every device but there are fixes too!
GSI fixes/patches/mods for RMX2117 will be uploaded in near future
Screenshots:
View attachment 5854217 View attachment 5854219 View attachment 5854225
Click to expand...
Click to collapse
hmmm sir may i ask if this works i oppo phone?
my phone specification is :
Name: Oppo A71
Model: CPH1717
Year realesed: 2017
Android version: Android 7.1.1 (Nougat) (Stock)
Name of android OS and Version: Color OS 3.1.1
Chipset: MT6750 (28nm)
Kernel version: 3.x.x (i forgot)
Bootloader State: Unlocked!
Twrp installed: Twrp 3.6.2 (Ported)
Rooted? : Yes- Magisk 25.2 latest
Size of the phone: 5.2 inch
Resolution: HD (1280 by 720 pixels)
Storage: 16 GB
Ram: 3 GB
since its GSI it doesnt modify the other partitions right only the system image right?
edit : sorry i think i know why you didnt reply ahhahah, i didnt notice the first sentence eheh my phone isnt project treble supported

Can I flash this gsi if a stock rom is bootlooping ?