Root SM-N910T loops - Android General

I've tried to root my phone using this procedure:
How to root Samsung Note 4 SM-N910T and after I used Obi3 to load CF-Auto-Root.tar file, phone went to this page:
RECOVERY BOOTING.....
RECOVERY IS NOT SEANDROID ENFORCING
Set Warranty Bit : recovery
Click to expand...
Click to collapse
And whatever I do it boots only in this page now...
Is it any way to recover from this?
Thank you in advance!

This is very serious problem. Phone starts only with the screen mentioned in my first post. There is no Android Recovery available (if I press VolumeUP+Power+Home it goes to the same screen only). I can only go to Download mode and try to update it with CF-Auto-Root.tar file. But it doesn't help. Phone boots only into one screen only and there is no way to bypass it now.
Please help!

Do not ever use the procedure from the site, mentioned in my first post! It's full of BS (to go to Download mode you have to press VolumeDOWN+Home+Power and not VolumeUP+Home+Power) and the file provided there will soft-brick your phone with endless loop as I've described above
Here is the proper procedure to root SM-N910T phone:
1. Download and install Samsung USB driver Samsung-Usb-Driver-v1.5.63.0
2. Download and extract CF-Auto-Root-trltetmo-trltetmo-smn910t.tar.md5 file. See list of all devices - CF-Auto-Root
3. Turn off phone and boot into Download mode. Press VolumeDWN+Home+Power buttons
4. In Download mode if you see warning yellow triangle, then press VoumelUP to continue
5. Run (as admin) Odin3 and connect phone to computer
6. Once device is detected, click on AP button and select CF-Auto-Root-trltetmo-trltetmo-smn910t.tar.md5 file
7. Wait for couple minutes until rooting is completed and you see PASS! becoming green on top
Now you phone will boot normally and will set its root

Related

[help] i9003 stuck in boot loop

HI,
i've been wanting to root and install custom roms on the i9003. i finally got the courage to try to root and do all these things recently, so i rooted the phone using superoneclick.. but i didnt know what to do next, because i wanted to try out custom roms because of what i have been reading on the forums.
so i followed the instructions here: http://forum.xda-developers.com/showpost.php?p=19442301&postcount=1 and flashed the bagaria.tar found here using ODIN.
but it started looping and kept rebooting over and over again. and got stuck in bootloop. eventually it came up and would respond a bit before going back to the booting sequence, and i noticed that opening CWM automatically sent the phone to booting.
thinking that i did something wrong and afraid that i bricked the device i went to this thread and looked for the dxkp9 stock and used odin with it (http://forum.xda-developers.com/showthread.php?t=1004647)
it just is stuck on boot loop now.
i've tried removing the battery and trying holding the VOLup home and power to no avail.
its just stuck in boot loop.
It is currently stuck in boot loop and wont do anything. i am really hoping it can still be fixed.. a bit of a sentimental value since this was a phone given to me by my dad, and first smartphone as well..
i would be very grateful for any kind of help.
getlucky88 said:
HI,
i've been wanting to root and install custom roms on the i9003. i finally got the courage to try to root and do all these things recently, so i rooted the phone using superoneclick.. but i didnt know what to do next, because i wanted to try out custom roms because of what i have been reading on the forums.
so i followed the instructions here: http://forum.xda-developers.com/showpost.php?p=19442301&postcount=1 and flashed the bagaria.tar found here using ODIN.
but it started looping and kept rebooting over and over again. and got stuck in bootloop. eventually it came up and would respond a bit before going back to the booting sequence, and i noticed that opening CWM automatically sent the phone to booting.
thinking that i did something wrong and afraid that i bricked the device i went to this thread and looked for the dxkp9 stock and used odin with it (http://forum.xda-developers.com/showthread.php?t=1004647)
it just is stuck on boot loop now.
i've tried removing the battery and trying holding the VOLup home and power to no avail.
its just stuck in boot loop.
It is currently stuck in boot loop and wont do anything. i am really hoping it can still be fixed.. a bit of a sentimental value since this was a phone given to me by my dad, and first smartphone as well..
i would be very grateful for any kind of help.
Click to expand...
Click to collapse
1. download stock rom I9003XXKPE from here http://forum.xda-developers.com/showthread.php?p=12310841#post12310841
Unzip and you will find the following files
1. Odin3v1.83(don't use this one, download latest version from here http://forum.xda-developers.com/showthread.php?t=1734997)
2.PIT file latona_20110114
3.BOOT LOADER-APBOOT_I9003XXKPE_CL409735_REV08_user_low_ship.tar.md5 file.
4.PDA-CODE_I9003XXKPE_CL409735_REV08_user_low_ship.tar.md5.
5.PHONE-MODEM_I9003XXKPE_REV_00_CL1041909.tar.md5.
6.CSC-GT-I9003-CSC-MULTI-OXAKPE.tar.md.
STEP 1
Go to download mode(press volume down+home then power),once in download mode, connect phone to computer -> double click odin3v1.83(make sure the bar under ID:COM turns yellow)
Double click "PIT" -> look for "latona_20110114" -> click "start", phone will turn off after finish(bar just above ID:COM turns green)
Take the battery out and return -> go to download mode again, connect phone to computer, double click Odin, make sure odin detects your phone, tick PDA, look for "CODE_I9003XXKPE_CL409735_REV08_user_low_ship.tar.md5"
tick PHONE, look for "MODEM_I9003XXKPE_REV_00_CL1041909.tar.md5"
tick CSC, look for "CSC-GT-I9003-CSC-MULTI-OXAKPE.tar.md"
Click "start", when it's done, you'll see a "PASS" on the odin, remove phone from computer, phone will restart automatically
Step 2 install value pack
Find and download a value pack of your choice from here http://forum.xda-developers.com/showthread.php?p=12310841#post12310841
I used the stable I9003DDLF2 (2.3.6) after downloaded, unzip the files, you should have "I9003DDLF2_I9003ODDLF2_I9003DDLE1_HOME.tar.md5"
Put your phone in download mode, connect to computer, start odin, tick PDA, search for I9003DDLF2_I9003ODDLF2_I9003DDLE1_HOME.tar.md5
Click "start", when it's done, you'll see a "PASS" on the odin, remove phone from computer, phone will restart automatically
Step3 apply root(I'm using XDA_Bam's)
Download "PDA_BCK_CF-root_universal_beta14fix.tar" from here http://forum.xda-developers.com/showthread.php?t=1355675
Again in download mode, connect to computer, start odin, tick PDA, search for "PDA_BCK_CF-root_universal_beta14fix.tar"
Click "start", when it's done, you'll see a "PASS" on the odin, remove phone from computer, phone will restart automatically
Step 4 apply custom roms(different roms have different requirements, read the instructions thoroughly)
download any custom rom of your choice, enter recovery mode(volume up + menu + power)
wipe data/factory reset, flash the rom zip(if google gapps is required->go to advanced -> Reboot Recovery -> Flash Google Apps -> reboot system
hard lesson learned
wee2wee said:
1. download stock rom I9003XXKPE from here http://forum.xda-developers.com/showthread.php?p=12310841#post12310841
Unzip and you will find the following files
1. Odin3v1.83(don't use this one, download latest version from here http://forum.xda-developers.com/showthread.php?t=1734997)
2.PIT file latona_20110114
3.BOOT LOADER-APBOOT_I9003XXKPE_CL409735_REV08_user_low_ship.tar.md5 file.
4.PDA-CODE_I9003XXKPE_CL409735_REV08_user_low_ship.tar.md5.
5.PHONE-MODEM_I9003XXKPE_REV_00_CL1041909.tar.md5.
6.CSC-GT-I9003-CSC-MULTI-OXAKPE.tar.md.
STEP 1
Go to download mode(press volume down,+menu+power),once in download mode, connect phone to computer -> double click odin3v1.83(make sure the bar under ID:COM turns yellow)
Double click "PIT" -> look for "latona_20110114" -> click "start", phone will turn off after finish(bar just above ID:COM turns green)
Take the battery out and return -> go to download mode again, connect phone to computer, double click Odin, make sure odin detects your phone, tick PDA, look for "CODE_I9003XXKPE_CL409735_REV08_user_low_ship.tar.md5"
tick PHONE, look for "MODEM_I9003XXKPE_REV_00_CL1041909.tar.md5"
tick CSC, look for "CSC-GT-I9003-CSC-MULTI-OXAKPE.tar.md"
Click "start", when it's done, remove phone from computer, phone will restart automatically
Step 2 install value pack
Find and download a value pack of your choice from here http://forum.xda-developers.com/showthread.php?p=12310841#post12310841
I used the stable I9003DDLF2 (2.3.6) after downloaded, unzip the files, you should have "I9003DDLF2_I9003ODDLF2_I9003DDLE1_HOME.tar.md5"
Put your phone in download mode, connect to computer, start odin, tick PDA, search for I9003DDLF2_I9003ODDLF2_I9003DDLE1_HOME.tar.md5
Click "start", when it's done, remove phone from computer, phone will restart automatically
Step3 apply root(I'm using XDA_Bam's)
Download "PDA_BCK_CF-root_universal_beta14fix.tar" from here http://forum.xda-developers.com/showthread.php?t=1355675
Again in download mode, connect to computer, start odin, tick PDA, search for "PDA_BCK_CF-root_universal_beta14fix.tar"
Click "start", when it's done, remove phone from computer, phone will restart automatically
Step 4 apply custom roms(different roms have different requirements, read the instructions thoroughly)
download any custom rom of your choice, enter recovery mode(volume up + menu + power)
wipe data/factory reset, flash the rom zip(if google gapps is required->go to advanced -> Reboot Recovery -> Flash Google Apps -> reboot system
Click to expand...
Click to collapse
:good:
thanks a lot for helping out the newbies like myself.
t is working again and i used the superoneclick method to root my phone.
is there like a recommended "rom" sli9003 users can start with as far as trying things out that arent touchwiz?
i tried (http://forum.xda-developers.com/showthread.php?t=1894737) but i would appreciate it if someone can point me to the right direction. as i am looking forward to learn more
thanks a lot!
getlucky88 said:
:good:
thanks a lot for helping out the newbies like myself.
t is working again and i used the superoneclick method to root my phone.
is there like a recommended "rom" sli9003 users can start with as far as trying things out that arent touchwiz?
i tried (http://forum.xda-developers.com/showthread.php?t=1894737) but i would appreciate it if someone can point me to the right direction. as i am looking forward to learn more
thanks a lot!
Click to expand...
Click to collapse
Make sure you know what you are doing before trying anything....try this http://forum.xda-developers.com/showthread.php?t=1492113
wee2wee said:
1. download stock rom I9003XXKPE from here http://forum.xda-developers.com/showthread.php?p=12310841#post12310841
Unzip and you will find the following files
1. Odin3v1.83(don't use this one, download latest version from here http://forum.xda-developers.com/showthread.php?t=1734997)
2.PIT file latona_20110114
3.BOOT LOADER-APBOOT_I9003XXKPE_CL409735_REV08_user_low_ship.tar.md5 file.
4.PDA-CODE_I9003XXKPE_CL409735_REV08_user_low_ship.tar.md5.
5.PHONE-MODEM_I9003XXKPE_REV_00_CL1041909.tar.md5.
6.CSC-GT-I9003-CSC-MULTI-OXAKPE.tar.md.
STEP 1
Go to download mode(press volume down,+menu+power),once in download mode, connect phone to computer -> double click odin3v1.83(make sure the bar under ID:COM turns yellow)
Double click "PIT" -> look for "latona_20110114" -> click "start", phone will turn off after finish(bar just above ID:COM turns green)
Take the battery out and return -> go to download mode again, connect phone to computer, double click Odin, make sure odin detects your phone, tick PDA, look for "CODE_I9003XXKPE_CL409735_REV08_user_low_ship.tar.md5"
tick PHONE, look for "MODEM_I9003XXKPE_REV_00_CL1041909.tar.md5"
tick CSC, look for "CSC-GT-I9003-CSC-MULTI-OXAKPE.tar.md"
Click "start", when it's done, remove phone from computer, phone will restart automatically
Step 2 install value pack
Find and download a value pack of your choice from here http://forum.xda-developers.com/showthread.php?p=12310841#post12310841
I used the stable I9003DDLF2 (2.3.6) after downloaded, unzip the files, you should have "I9003DDLF2_I9003ODDLF2_I9003DDLE1_HOME.tar.md5"
Put your phone in download mode, connect to computer, start odin, tick PDA, search for I9003DDLF2_I9003ODDLF2_I9003DDLE1_HOME.tar.md5
Click "start", when it's done, remove phone from computer, phone will restart automatically
Step3 apply root(I'm using XDA_Bam's)
Download "PDA_BCK_CF-root_universal_beta14fix.tar" from here http://forum.xda-developers.com/showthread.php?t=1355675
Again in download mode, connect to computer, start odin, tick PDA, search for "PDA_BCK_CF-root_universal_beta14fix.tar"
Click "start", when it's done, remove phone from computer, phone will restart automatically
Step 4 apply custom roms(different roms have different requirements, read the instructions thoroughly)
download any custom rom of your choice, enter recovery mode(volume up + menu + power)
wipe data/factory reset, flash the rom zip(if google gapps is required->go to advanced -> Reboot Recovery -> Flash Google Apps -> reboot system
Click to expand...
Click to collapse
Sir in my case everything goes well but after flashing with step 2 as mentioned above i get an error saying "E does not exist/ not possible" and the phone gets stuck in boot loop again where as after flashing the step 1 it was asking for password.
Pls help
rss31183
rss3183 said:
Sir in my case everything goes well but after flashing with step 2 as mentioned above i get an error saying "E does not exist/ not possible" and the phone gets stuck in boot loop again where as after flashing the step 1 it was asking for password.
Pls help
rss31183
Click to expand...
Click to collapse
After flashing step 1, did your phone restart/reboot normally?..what was asking for password? "everything goes well" for step1?
after flashing the files (pda modem etc.) the phone rebooted. but now is asking for a password go further. and when i tried to enter recovery and set it to factory settings it also asks for password before wiping the divice. tried a few times but with no success.
manu2002 said:
the password is maybe : samfirmware.com ............. maybe i saw it on http://forum.xda-developers.com/showthread.php?p=12310841#post12310841 below every rom
Click to expand...
Click to collapse
Greetings;
I didnt read all the stuff before...
So my answer may not be the best or accurate. (I'm almost out of time - sorry for that).
Either ways this happens to me when you don't perform a clean Flash (Formating Partitions before Flashing, wiping dalvik and cache) and after Flashing; performing a Factory Reset).
After the last step (Factory Reset) it should boot properly.
If not: Remove Battery, place it back and test if it boots.
From my experience: Downgrading ROM also do this issue. But i fix it by Flashing FULL DDLF2 (always with "clean flash") and then after my ROM Boots; Flashing the ROM i want to use.
Hope this helps.
When i flashed the first step my gt i9003 sl went completely blank except a bright light. Any solution or suggestiom

Bootloop P5100

My friend has a UNROOTED Galaxy Tab 2 10.1" and it's stuck on the Samsung screen (bootloop). I guided her towards recovery mode but it doesn't work. It doesn't boot to recovery mode but it does to download mode. How do I fix this?
There is one way to solve this.
Using odin[You need a pc for this]
follow the steps.
1.Install Odin in your PC from here
http://odindownload.com/download/Odin3_v3.10.6.zip
2.download the official firmware of your device from sammobiles .
http://www.sammobile.com/firmwares/
3.Go to download mode in your device (vol down+power button)
4.Now connect your device to the pc and open Odin.
5.Now open Odin in your PC and under PDA browse for the firmware you downloaded and click start.
6.Now wait till it says pass. After that detach your device and wait till it boots.
This reboot may take like 5-15 mins. Incase it doesn't boot up even 30mins just try going to recovery and perform a factory reset.
THATS IT.YOU HAVE SOLVED YOUR PROBLEM.
HIT THANKS IF THIS HELPED YOU!!!!
:good:

[GUIDE] How to unbrick Galaxy Tab 3 10.1

Hey, in this tutorial I'll tell you how to unbrick hard-bricked Tab 3.
So, if you have message that you must repair your Tab 3 in Samsung Kies, and you can't recover it (you have corrupted system and have no recovery), first thing that you must do is to download Odin here: http://odindownload.com/ and TWRP recovery (make sure that you downloaded the version for your tablet): version for model P5200 - https://goo.gl/mzY5kV and for model P5210 - https://goo.gl/mcxy3E. Then download stock ROM from sammobile.com. WARNING! Never flash ROM on the tablet in such a state. When you do this, you'll see FAILED message in Odin and you won't repair anything. Then you must turn off tablet and boot into download mode (hold power+volume down+home). Then connect your tablet to the computer and open Odin with administrator rights. Now you gonna to click AP button and locate and open twrp file (with .md5 extension) and when it is loaded click Start button. When recovery is flashed, plug off the cable and then you must turn off your tablet and boot into recovery mode (hold power+volume up+home). Now you must click Wipe>Advanced Wipe and mark everything (without USB-OTG and SD Card) and click button Wipe. After wiping, you must click Reboot and Download. You'll be in download mode and make sure that there isn't any text in the upper left corner. When there isn't anything then this means that you haven't anything on your tablet. Now you must open Odin again and plug the cable in. Then click AP button and locate and open your ROM. Now you must click Start and wait. When the ROM is flashed, the tablet should restart automatically. Then unplug the cable and wait for the tablet to boot. After few minutes, you should see the welcome message. When you see it, it means that tablet is working and the repair is completed.
I hope that this tutorial helped you
this is not hard bricked this is soft bricked. hard bricked is when you cannot turn on your device to enter the recover and download mode. i hope you do your research. please correct the title.

How To Root Samsung GALAXY J2 (SM-J200/G/H/F/M) UPDATED!

Hi Guys,
I Am Going To Guide You How To Root Your Samsung Galaxy J2 (All 2015 Variants).
I AM NOT RESPONSIBLE FOR ANY DAMAGE OR ANY HARM OCCURRED WITH YOU DURING THE PROCESS !
GUYS, FOLLOW EACH STEP CORRECTLY FOR THE PERFECT SOLUTION.
Your Samsung Galaxy J2 May Be Have Latest Or Lowest Version Of Firmware, It Doesn't Matter.
STEP 1: UNLOCKING THE BOOTLOADER :-
Switch ON Your Phone.
Goto >>SETTINGS >>ABOUT DEVICE>>TAP THE BUILD NUMBER 3 TO 5 TIMES.
Get Back To SETTINGS And Goto >>DEVELOPER OPTIONS>>TURN "ON" OEM UNLOCK.
This Will Unlock Your BOOTLOADER.
STEP 2: DOWNLOADING THE TWRP RECOVERY (CUSTOM RECOVERY) :-
Visit TWRP Homepage.
Download The File "twrp-3.1.1-0-j2lte.img.tar"
(The Latest Version Of TWRP Recovery For Galaxy J2)
OR Just Google It, You Will Find It Easily.
STEP 3: DOWNLOADING SAMSUNG ANDROID USB DRIVERS SETUP AND ODIN TOOL :-
Visit Samsung Support Files And Download Latest Android USB Drivers For Samsung.
And Also Download Latest Version Of ODIN Tool.
(These Both Files Can Be Found Very Easily By Google)
STEP 4: FLASHING THE TWRP RECOVERY.
Make Sure You Have Installed The Latest USB Drivers For Samsung And Have Latest Version Of ODIN Tool.
Switch OFF Your Phone. (To Make Sure It Is Switched Off, Remove Battery And Re - Insert It)
Boot Your Phone Into Download Mode. (This Can Be Easily Done By Holding The "VOLUME DOWN + HOME + POWER" Buttons At A Same Time.)
Now Your Phone's Screen Shows Download Mode.
Open The "ODIN.EXE" File (After The Extracting The ODIN.ZIP).
Click On "PDA" OR "AP" Then Browse And Select The "twrp-3.1.1-0-j2lte.img.tar" File.
Now, Connect Your Phone To The PC With The USB Cable. (Make Sure That Your Cable Is Not Damaged And It is At It's Peak Performance.)
Wait Until You See The "Added" Message In The Log Section Of ODIN Tool.
Now, Click On "START" To Begin The Flashing Process.
Wait Until The Process Is Completed And Then ODIN Shows The "PASS" OR "RESET" Message.
Disconnect The Phone From The PC And Let It To Power ON Itself.
STEP 5: DOWNLOADING SUPERSU FILE AND FLASHING IT WITH TWRP RECOVERY :-
Search The File "EXPERIMENTAL-BETA-SuperSU-v2.66-20160103015024.Zip" And Download It.
Put It Into Your Internal Or External Storage.
Switch OFF Your Phone.
Boot Your Into Recover Mode. (This Can Be Easily Done By Holding The "VOLUME UP + HOME + POWER" Buttons At A Same Time.)
Now Instead Of Stock Recovery, You Will See The TWRP Recovery.
At The First Time It Will Ask For Mount System.
Swipe And Give Permissions To Mount The System.
Now, Click On "INSTALL" And Browse Your Downloaded SUPERSU.Zip And Swipe To Flash It.
Wait Till The Flash Is Completed And Then Click On "REBOOT SYSTEM".
The Phone Will Reboots Itself. (It Will Reboot For Two Times, Don't Worry ; Let It To Boot Completely And Don't Interrupt The Process.
After The Successful Boot Up, It Will Show Android Is Upgrading And Takes You To The Home Launcher ; Launch Your App Drawer To See Your SUPERSU App Installed.
STEP 6: ROOT VERIFICATION :-
Goto Play Store And Download Root Checker Basic App.
Launch It And Verify Yourself.
KEEP SMILING!!!
DOWNLOAD LINKS :-
1. Samsung Android USB Drivers :
http://developer.samsung.com/galaxy/others/android-usb-driver-for-windows
2. ODIN Tool :
http://odindownload.com/mobile/
3. TWRP Recovery :
https://dl.twrp.me/j2lte/
4. SUPERSU :
https://forum.xda-developers.com/showpost.php?p=64161125
Peeran said:
Hi Guys,
I Am Going To Guide You How To Root Your Samsung Galaxy J2 (All 2015 Variants).
I AM NOT RESPONSIBLE FOR ANY DAMAGE OR ANY HARM OCCURRED WITH YOU DURING THE PROCESS !
GUYS, FOLLOW EACH STEP CORRECTLY FOR THE PERFECT SOLUTION.
Your Samsung Galaxy J2 May Be Have Latest Or Lowest Version Of Firmware, It Doesn't Matter.
STEP 1: UNLOCKING THE BOOTLOADER :-
Switch ON Your Phone.
Goto >>SETTINGS >>ABOUT DEVICE>>TAP THE BUILD NUMBER 3 TO 5 TIMES.
Get Back To SETTINGS And Goto >>DEVELOPER OPTIONS>>TURN "ON" OEM UNLOCK.
This Will Unlock Your BOOTLOADER.
STEP 2: DOWNLOADING THE TWRP RECOVERY (CUSTOM RECOVERY) :-
Visit TWRP Homepage.
Download The File "twrp-3.1.1-0-j2lte.img.tar"
(The Latest Version Of TWRP Recovery For Galaxy J2)
OR Just Google It, You Will Find It Easily.
STEP 3: DOWNLOADING SAMSUNG ANDROID USB DRIVERS SETUP AND ODIN TOOL :-
Visit Samsung Support Files And Download Latest Android USB Drivers For Samsung.
And Also Download Latest Version Of ODIN Tool.
(These Both Files Can Be Found Very Easily By Google)
STEP 4: FLASHING THE TWRP RECOVERY.
Make Sure You Have Installed The Latest USB Drivers For Samsung And Have Latest Version Of ODIN Tool.
Switch OFF Your Phone. (To Make Sure It Is Switched Off, Remove Battery And Re - Insert It)
Boot Your Phone Into Download Mode. (This Can Be Easily Done By Holding The "VOLUME DOWN + HOME + POWER" Buttons At A Same Time.)
Now Your Phone's Screen Shows Download Mode.
Open The "ODIN.EXE" File (After The Extracting The ODIN.ZIP).
Click On "PDA" OR "AP" Then Browse And Select The "twrp-3.1.1-0-j2lte.img.tar" File.
Now, Connect Your Phone To The PC With The USB Cable. (Make Sure That Your Cable Is Not Damaged And It is At It's Peak Performance.)
Wait Until You See The "Added" Message In The Log Section Of ODIN Tool.
Now, Click On "START" To Begin The Flashing Process.
Wait Until The Process Is Completed And Then ODIN Shows The "PASS" OR "RESET" Message.
Disconnect The Phone From The PC And Let It To Power ON Itself.
STEP 5: DOWNLOADING SUPERSU FILE AND FLASHING IT WITH TWRP RECOVERY :-
Search The File "EXPERIMENTAL-BETA-SuperSU-v2.66-20160103015024.Zip" And Download It.
Put It Into Your Internal Or External Storage.
Switch OFF Your Phone.
Boot Your Into Recover Mode. (This Can Be Easily Done By Holding The "VOLUME UP + HOME + POWER" Buttons At A Same Time.)
Now Instead Of Stock Recovery, You Will See The TWRP Recovery.
At The First Time It Will Ask For Mount System.
Swipe And Give Permissions To Mount The System.
Now, Click On "INSTALL" And Browse Your Downloaded SUPERSU.Zip And Swipe To Flash It.
Wait Till The Flash Is Completed And Then Click On "REBOOT SYSTEM".
The Phone Will Reboots Itself. (It Will Reboot For Two Times, Don't Worry ; Let It To Boot Completely And Don't Interrupt The Process.
After The Successful Boot Up, It Will Show Android Is Upgrading And Takes You To The Home Launcher ; Launch Your App Drawer To See Your SUPERSU App Installed.
STEP 6: ROOT VERIFICATION :-
Goto Play Store And Download Root Checker Basic App.
Launch It And Verify Yourself.
KEEP SMILING!!!
DOWNLOAD LINKS :-
1. Samsung Android USB Drivers :
http://developer.samsung.com/galaxy/others/android-usb-driver-for-windows
2. ODIN Tool :
http://odindownload.com/mobile/
3. TWRP Recovery :
https://dl.twrp.me/j2lte/
4. SUPERSU :
https://forum.xda-developers.com/showpost.php?p=64161125
Click to expand...
Click to collapse
Will this twrp works on j23g? I don't think so..
Yes,of course.
Is it working on all type of j2?
Samial said:
Is it working on all type of j2?
Click to expand...
Click to collapse
Nope
here`s the twrp for j23g
https://forum.xda-developers.com/ga...p-3-0-2-1-samsung-galaxy-j2-sm-j200h-t3486994
and for root Just use magisk, it works on almost all smartphones and has much more features.
problems faced and solns found
1. During twrp flashing using odin, my stock recovery kept patching the twrp after reboots. So i couldn't install twrp succesfully. To fix this I unchecked "reboot" option in odin (thanks to another xda rooting guide)and switched off device manually after flashing. Then booted into recovery by pressing "home+vol up+power". this time stock rom was gone and twrp was there to welcome me.
2. i ended up in a bootloop after flashing the aforementioned superuser zip file. Instead i flashed BETA-SuperSU-v2.74-2-20160519174328.zip and fixed the bootloop.
Note- My device is Samsung Galaxy j200-G.
Here are some links to go through(as i did) ,if you face same problems:
1. https://twrp.me/samsung/samsunggalaxyj2.html
2. https://forum.xda-developers.com/ga...p-3-0-2-1-samsung-galaxy-j2-sm-j200h-t3486994
3. https://www.androidinfotech.com/2016/07/root-samsung-galaxy-j2-sm-j200g-511.html
How I can unlock bootloader permanently??
SM-J200G
Will this work on SAMSUNG J200GU?
But unable to access twrp 2nd time it show custom recovery blocked by frp lock
abhi91ar said:
But unable to access twrp 2nd time it show custom recovery blocked by frp lock
Click to expand...
Click to collapse
Turn on Oem unlock in developer options.
§Ani§ said:
Turn on Oem unlock in developer options.
Click to expand...
Click to collapse
Already turned on but problem still exists. What to do now? Help me?
Ok i will try
I s there any best ROM with higher version for Samsung SM-J200H
Rooting samsung j200gu
abinashdash17 said:
1. During twrp flashing using odin, my stock recovery kept patching the twrp after reboots. So i couldn't install twrp succesfully. To fix this I unchecked "reboot" option in odin (thanks to another xda rooting guide)and switched off device manually after flashing. Then booted into recovery by pressing "home+vol up+power". this time stock rom was gone and twrp was there to welcome me.
2. i ended up in a bootloop after flashing the aforementioned superuser zip file. Instead i flashed BETA-SuperSU-v2.74-2-20160519174328.zip and fixed the bootloop.
Note- My device is Samsung Galaxy j200-G.
Here are some links to go through(as i did) ,if you face same problems:
1. https://twrp.me/samsung/samsunggalaxyj2.html
2. https://forum.xda-developers.com/ga...p-3-0-2-1-samsung-galaxy-j2-sm-j200h-t3486994
3. https://www.androidinfotech.com/2016/07/root-samsung-galaxy-j2-sm-j200g-511.html
Click to expand...
Click to collapse
Wow thank you so much bro I now have rooted my phone!! (Samsung J200GU):good: :laugh:
Note: I flashed SR5-SuperSU-v2.78-SR5-20161130091551 instead of the 2.74 mentioned above?
abhi91ar said:
Already turned on but problem still exists. What to do now? Help me
Click to expand...
Click to collapse
Turn off auto reboot in odin and then flash.
Does this work on Sm-J200h? Trying to root my device but I am doing a little research before I do.
Peeran said:
Hi Guys,
I Am Going To Guide You How To Root Your Samsung Galaxy J2 (All 2015 Variants).
I AM NOT RESPONSIBLE FOR ANY DAMAGE OR ANY HARM OCCURRED WITH YOU DURING THE PROCESS !
GUYS, FOLLOW EACH STEP CORRECTLY FOR THE PERFECT SOLUTION.
Your Samsung Galaxy J2 May Be Have Latest Or Lowest Version Of Firmware, It Doesn't Matter.
STEP 1: UNLOCKING THE BOOTLOADER :-
Switch ON Your Phone.
Goto >>SETTINGS >>ABOUT DEVICE>>TAP THE BUILD NUMBER 3 TO 5 TIMES.
Get Back To SETTINGS And Goto >>DEVELOPER OPTIONS>>TURN "ON" OEM UNLOCK.
This Will Unlock Your BOOTLOADER.
STEP 2: DOWNLOADING THE TWRP RECOVERY (CUSTOM RECOVERY) :-
Visit TWRP Homepage.
Download The File "twrp-3.1.1-0-j2lte.img.tar"
(The Latest Version Of TWRP Recovery For Galaxy J2)
OR Just Google It, You Will Find It Easily.
STEP 3: DOWNLOADING SAMSUNG ANDROID USB DRIVERS SETUP AND ODIN TOOL :-
Visit Samsung Support Files And Download Latest Android USB Drivers For Samsung.
And Also Download Latest Version Of ODIN Tool.
(These Both Files Can Be Found Very Easily By Google)
STEP 4: FLASHING THE TWRP RECOVERY.
Make Sure You Have Installed The Latest USB Drivers For Samsung And Have Latest Version Of ODIN Tool.
Switch OFF Your Phone. (To Make Sure It Is Switched Off, Remove Battery And Re - Insert It)
Boot Your Phone Into Download Mode. (This Can Be Easily Done By Holding The "VOLUME DOWN + HOME + POWER" Buttons At A Same Time.)
Now Your Phone's Screen Shows Download Mode.
Open The "ODIN.EXE" File (After The Extracting The ODIN.ZIP).
Click On "PDA" OR "AP" Then Browse And Select The "twrp-3.1.1-0-j2lte.img.tar" File.
Now, Connect Your Phone To The PC With The USB Cable. (Make Sure That Your Cable Is Not Damaged And It is At It's Peak Performance.)
Wait Until You See The "Added" Message In The Log Section Of ODIN Tool.
Now, Click On "START" To Begin The Flashing Process.
Wait Until The Process Is Completed And Then ODIN Shows The "PASS" OR "RESET" Message.
Disconnect The Phone From The PC And Let It To Power ON Itself.
STEP 5: DOWNLOADING SUPERSU FILE AND FLASHING IT WITH TWRP RECOVERY :-
Search The File "EXPERIMENTAL-BETA-SuperSU-v2.66-20160103015024.Zip" And Download It.
Put It Into Your Internal Or External Storage.
Switch OFF Your Phone.
Boot Your Into Recover Mode. (This Can Be Easily Done By Holding The "VOLUME UP + HOME + POWER" Buttons At A Same Time.)
Now Instead Of Stock Recovery, You Will See The TWRP Recovery.
At The First Time It Will Ask For Mount System.
Swipe And Give Permissions To Mount The System.
Now, Click On "INSTALL" And Browse Your Downloaded SUPERSU.Zip And Swipe To Flash It.
Wait Till The Flash Is Completed And Then Click On "REBOOT SYSTEM".
The Phone Will Reboots Itself. (It Will Reboot For Two Times, Don't Worry ; Let It To Boot Completely And Don't Interrupt The Process.
After The Successful Boot Up, It Will Show Android Is Upgrading And Takes You To The Home Launcher ; Launch Your App Drawer To See Your SUPERSU App Installed.
STEP 6: ROOT VERIFICATION :-
Goto Play Store And Download Root Checker Basic App.
Launch It And Verify Yourself.
KEEP SMILING!!!
DOWNLOAD LINKS :-
1. Samsung Android USB Drivers :
http://developer.samsung.com/galaxy/others/android-usb-driver-for-windows
2. ODIN Tool :
http://odindownload.com/mobile/
3. TWRP Recovery :
https://dl.twrp.me/j2lte/
4. SUPERSU :
https://forum.xda-developers.com/showpost.php?p=64161125
Click to expand...
Click to collapse
whether after I take the steps above my data will be lost ?
Phones bricked now....
you dog my phones bricked should of mentioned to make a backup u fuk wit
Nice Tutorials
Hey i m ramcharan thanks nice guide how to root samsung J200G

ROOT J2 PRIME (SM-G532 F/M/G) SUPEREASY 5 steps

now i was looking for how to root my j2 prime because its what i use to login with my vpn then i use a proxy server on it to route all traffic connected to it while its in hotspot mode but it seems proxy servers have their limitations and so im forced to root so i can just hotspot the vpn directly with an app, but after searching i found 3 methods all using superSU which im not comfortable with anymore, all with many steps but in my experice since this phone has got nothing to lose i decided to experiment and boom it worked...
what you need
latest Magsisk - v17.1 at this time of posting
latest SAMSUNG USB DRIVERS
ODIN
and TWRP by
ashyx said:
STEPS
1. BOOT PHONE IN DOWNLAOD MODE (power+vold-down+home)
2. FLASH TWRP in the AP OPTION in ODIN (untick auto reboot;very important) then after flash succeeds
3. Pull out battery and boot to recovery (power+vol-up+home)
4. FLASH MAGISK.zip from your SDCARD (Recovery wont be able to mount internal storage so make sure to put the MAGISK.zip in your SDCARD)
5. Reboot and Hello systemless root
credits to this thread where i was searching for root, includes link to 3 methods but mine is the shortest and easiest
Click to expand...
Click to collapse
I'm unable to start recovery mode. I pull out the battery and after pressing the keys the phone simply goes off. Also I'm unable to enter recovery mode anyway (after turning it off and not flashing anything). That's it, I can't enter stock recovery either.
I tried all button combinations and it just doesn't enter recovery mode.
Never mind, it was probably a faulty button. Pressing with force did the trick. I however employed a bit different path (or perhaps I wrote it down more detailed), which come out more noob like, I'll leave them here for anyone that might use them
Noob, baby steps to root the Samsung Galaxy J2 Prime SM-G532M:
1. Enable developer mode and selected OEM unlocking and USB debug, dunno if it's needed but I did it because in all roots I have seen this is a must.
2. Put the Magisk zip onto a SD card (currently Magisk-v18.0) and put the SD card into the phone. Then I turned off the phone.
3. Turn on the phone into download mode (power+vold-down+home), connect the phone to the PC.
4. Open ODIN and FLASH TWRP file using the AP button (VERY IMPORTANT, uncheck the auto reboot in options, otherwise the recovery goes back to stock I think and the phone will boot into the regular OS, and you'll have to flash TWRP again), wait a few seconds to the flash to finish (odin says PASS! in green).
5. From this screen without touching anything reboot the phone into recovery mode (power+vol-up+home) (just in case press hard the vol+ key). If it boots the phone in regular mode, do steps 2 , 3 and 4 again.
6. FLASH MAGISK.zip from the microSD. When finished wipe Delvik/Cache.
7. Reboot the system. Open the Magisk app (you might have to wait a few seconds for it to appear among on the apps) then press yes when prompted to finish installation as many times (2 times I think). And done, you have your phone rooted.
PD: Magisk can be found here: https://github.com/topjohnwu/Magisk/releases/
As for the TWRP file (twrp_3.1.0-1_sm-g532_5617b.tar), use the one in the link on the OP.
LordBaal19 said:
6. FLASH MAGISK.zip from the microSD. When finished wipe Delvik/Cache.
7. Reboot the system. Open the Magisk app (you might have to wait a few seconds for it to appear among on the apps) then press yes when prompted to finish installation as many times (2 times I think). And done, you have your phone rooted..
Click to expand...
Click to collapse
why am i getting an error? it says
"Updater process ended with ERROR: 1
Error installing zip file '/external_sd/Magisk-v17.1.zip' "
can i get some help here?
Good day!
Is disabling dm-verity and force encryption included in the process?
And also, everything works fine but how is that i cannot delete system apps manually? They're returning back after reboot.
Thanks.
Unable to detect the phone -win nor Lin
Hello guys
Something really extrange is happening.
My j2 prime -532G- can't be detected by Windows nor Linux.
The usb is working because it charges the phone, but I can't access the phone at all. I checked all the drivers in Win -google/adb and samsung- and in Linux libmtp/heimdall/etc.
I have tryed different usb -not the original one since i lost it-
Even when i start the download mode, nothing happens.
it there a way to root the phone without a PC? i have tryed also kingroot apk but it is useless.
Thanks
LordBaal19 said:
I'm unable to start recovery mode. I pull out the battery and after pressing the keys the phone simply goes off. Also I'm unable to enter recovery mode anyway (after turning it off and not flashing anything). That's it, I can't enter stock recovery either.
I tried all button combinations and it just doesn't enter recovery mode.
Never mind, it was probably a faulty button. Pressing with force did the trick. I however employed a bit different path (or perhaps I wrote it down more detailed), which come out more noob like, I'll leave them here for anyone that might use them
Noob, baby steps to root the Samsung Galaxy J2 Prime SM-G532M:
1. Enable developer mode and selected OEM unlocking and USB debug, dunno if it's needed but I did it because in all roots I have seen this is a must.
2. Put the Magisk zip onto a SD card (currently Magisk-v18.0) and put the SD card into the phone. Then I turned off the phone.
3. Turn on the phone into download mode (power+vold-down+home), connect the phone to the PC.
4. Open ODIN and FLASH TWRP file using the AP button (VERY IMPORTANT, uncheck the auto reboot in options, otherwise the recovery goes back to stock I think and the phone will boot into the regular OS, and you'll have to flash TWRP again), wait a few seconds to the flash to finish (odin says PASS! in green).
5. From this screen without touching anything reboot the phone into recovery mode (power+vol-up+home) (just in case press hard the vol+ key). If it boots the phone in regular mode, do steps 2 , 3 and 4 again.
6. FLASH MAGISK.zip from the microSD. When finished wipe Delvik/Cache.
7. Reboot the system. Open the Magisk app (you might have to wait a few seconds for it to appear among on the apps) then press yes when prompted to finish installation as many times (2 times I think). And done, you have your phone rooted.
PD: Magisk can be found here: https://github.com/topjohnwu/Magisk/releases/
As for the TWRP file (twrp_3.1.0-1_sm-g532_5617b.tar), use the one in the link on the OP.
Click to expand...
Click to collapse
I can't seem to get this phone to go into recovery after flashing TWRP. It always goes into a normal reboot no matter how hard i press the button combination.
Any idea about how to make it reboot to recovery any other way
BTW I was aable to make it go to TWRP Once but forgot to insert the SD card that time and had to repeat the process again and haven't been able to see that TWRP screen agin
Any ideas
mbalino said:
Win -google/adb and samsung- and in Linux libmtp/heimdall/etc.
Click to expand...
Click to collapse
Hello mbalino I am new to XDA forums
Where did you checked the drivers in the phone or the PC? what drivers are they?
mbalino said:
My j2 prime -532G- can't be detected by Windows nor Linux.
The usb is working because it charges the phone,
Click to expand...
Click to collapse
Did the phone trigger an Autoplay window (to ask you if you want "view files", "import media", etc.)
Did the phone appear in the file explorer (as a media player device?) with storage(s)?

Categories

Resources