Database Info

How to Root Note Edge (SM-N915T) with Marshmallow 6.0.1?

Hello,
XDA, would it be possible to look into rooting a Samsung Note Edge (SM-N915T) with Marshmallow 6.0.1. I've tried different things, but there doesn't seem to be a process for this phone with that OS.
Let me know.
Thanks,
Whirlpool14

whirlpool14 said:
Hello,
XDA, would it be possible to look into rooting a Samsung Note Edge (SM-N915T) with Marshmallow 6.0.1. I've tried different things, but there doesn't seem to be a process for this phone with that OS.
Let me know.
Thanks,
Whirlpool14
Click to expand...
Click to collapse
you should flash via Odin for CWM and pull out battery method if notified FAIL, also cautioned about the SUPERSU must be 2.76 which patched the Samsung security updated, i was success rooted my Sprint 915P FW6.0.1 dueto this way

I rooted my phone following this procedure (the FY version of the Note Edge but should work for any other)
You need the following tools:
Samsung drivers:
https://www.dropbox.com/s/3d61st8zaxas4pt/SAMSUNG_USB_Driver_for_Mobile_Phones_1_5_6_0.exe?dl=0
Odin 3:09:
https://www.dropbox.com/s/ua0sqizz1m6558d/Odin3_v3.09.zip?dl=0
SuperSU 2.74:
https://download.chainfire.eu/964/SuperSU/BETA-SuperSU-v2.74-2-20160519174328.zip?retrieve_file=1
and CWM for the T version of the Note (from this thread):
http://forum.xda-developers.com/not...15s-n9150-cwm-based-recovery-6-0-5-1-t2954960
Move all files to a folder on the PC.
Copy the SuperSU your Cell (SD card int/ext).
Install the drivers for the phone.
Then go with the phone in the DL (download) mode.
Start Odin, connect the phone to the PC.
If Odin recognizes the cell phone continue.
Some side notes:
To get in DL (download) mode use key combination <VOL DOWN + HOME + POWER>.
To get in recovery mode use key combination <UP VOL + HOME + POWER>.
Press these buttons simultaneously.
You flash CWM in DL mode via Odin (in "AP" insert CWM) to the mobile phone.
It is important that you previously deactivate "Auto Reboot" in Odin.
When the flash process is finished, you just wait one minute after you have pressed the "Start", pull the cable from the phone and remove the battery.
Wait a couple seconds, and put the battery back inside.
Now, and this is important, you have to come directly into recovery mode.
If the phone starts normally into the system, CWM is overwritten with the standard recovery.
If you're in CWM, you go to "Install zip" and select the SuperSU to install.
ATTENTION: if CWM asks you to install root or SuperSU, answer with NO, else you get a bootloop!
Now you can Restart, normal into the system.
That's it already, if you're in the system, you install this app from Play Store:
https://play.google.com/store/apps/details?id=com.jrummyapps.rootchecker
When you got root just update SuperSU and install busybox and you are good to go

help
btotaku said:
I rooted my phone following this procedure (the FY version of the Note Edge but should work for any other)
You need the following tools:
Samsung drivers:
https://www.dropbox.com/s/3d61st8zaxas4pt/SAMSUNG_USB_Driver_for_Mobile_Phones_1_5_6_0.exe?dl=0
Odin 3:09:
https://www.dropbox.com/s/ua0sqizz1m6558d/Odin3_v3.09.zip?dl=0
SuperSU 2.74:
https://download.chainfire.eu/964/SuperSU/BETA-SuperSU-v2.74-2-20160519174328.zip?retrieve_file=1
and CWM for the T version of the Note (from this thread):
http://forum.xda-developers.com/not...15s-n9150-cwm-based-recovery-6-0-5-1-t2954960
Move all files to a folder on the PC.
Copy the SuperSU your Cell (SD card int/ext).
Install the drivers for the phone.
Then go with the phone in the DL (download) mode.
Start Odin, connect the phone to the PC.
If Odin recognizes the cell phone continue.
Some side notes:
To get in DL (download) mode use key combination <VOL DOWN + HOME + POWER>.
To get in recovery mode use key combination <UP VOL + HOME + POWER>.
Press these buttons simultaneously.
You flash CWM in DL mode via Odin (in "AP" insert CWM) to the mobile phone.
It is important that you previously deactivate "Auto Reboot" in Odin.
When the flash process is finished, you just wait one minute after you have pressed the "Start", pull the cable from the phone and remove the battery.
Wait a couple seconds, and put the battery back inside.
Now, and this is important, you have to come directly into recovery mode.
If the phone starts normally into the system, CWM is overwritten with the standard recovery.
If you're in CWM, you go to "Install zip" and select the SuperSU to install.
ATTENTION: if CWM asks you to install root or SuperSU, answer with NO, else you get a bootloop!
Now you can Restart, normal into the system.
That's it already, if you're in the system, you install this app from Play Store:
https://play.google.com/store/apps/details?id=com.jrummyapps.rootchecker
When you got root just update SuperSU and install busybox and you are good to go
Click to expand...
Click to collapse
i have the fy version can you help me retrieve the file for that model ??

edoluck90 said:
i have the fy version can you help me retrieve the file for that model ??
Click to expand...
Click to collapse
Go with the CWM for the F version here, this will work with FY as well, i did it myself > http://forum.xda-developers.com/attachment.php?attachmentid=3037310&d=1417138979

btotaku said:
Go with the CWM for the F version here, this will work with FY as well, i did it myself > http://forum.xda-developers.com/attachment.php?attachmentid=3037310&d=1417138979
Click to expand...
Click to collapse
OK .i feel more secure if anyone can give me a tutorial because is the first time I root a new gen phone, the last phone I root is a galaxy 2. Thanks for your time

edoluck90 said:
OK .i feel more secure if anyone can give me a tutorial because is the first time I root a new gen phone, the last phone I root is a galaxy 2. Thanks for your time
Click to expand...
Click to collapse
You can follow my instruction step by step, i did it exactly the same way. You can check handy-faq forum as well, i got the instructions there and just replaced TWRP with CWM, just read in german here > http://www.handy-faq.de/forum/galaxy-note-edge-root-cwm-based-recovery-6-0-5-1-t313111/?page=3

btotaku said:
I rooted my phone following this procedure (the FY version of the Note Edge but should work for any other)
You need the following tools:
Samsung drivers:
https://www.dropbox.com/s/3d61st8zaxas4pt/SAMSUNG_USB_Driver_for_Mobile_Phones_1_5_6_0.exe?dl=0
Odin 3:09:
https://www.dropbox.com/s/ua0sqizz1m6558d/Odin3_v3.09.zip?dl=0
SuperSU 2.74:
https://download.chainfire.eu/964/SuperSU/BETA-SuperSU-v2.74-2-20160519174328.zip?retrieve_file=1
and CWM for the T version of the Note (from this thread):
http://forum.xda-developers.com/not...15s-n9150-cwm-based-recovery-6-0-5-1-t2954960
Move all files to a folder on the PC.
Copy the SuperSU your Cell (SD card int/ext).
Install the drivers for the phone.
Then go with the phone in the DL (download) mode.
Start Odin, connect the phone to the PC.
If Odin recognizes the cell phone continue.
Some side notes:
To get in DL (download) mode use key combination <VOL DOWN + HOME + POWER>.
To get in recovery mode use key combination <UP VOL + HOME + POWER>.
Press these buttons simultaneously.
You flash CWM in DL mode via Odin (in "AP" insert CWM) to the mobile phone.
It is important that you previously deactivate "Auto Reboot" in Odin.
When the flash process is finished, you just wait one minute after you have pressed the "Start", pull the cable from the phone and remove the battery.
Wait a couple seconds, and put the battery back inside.
Now, and this is important, you have to come directly into recovery mode.
If the phone starts normally into the system, CWM is overwritten with the standard recovery.
If you're in CWM, you go to "Install zip" and select the SuperSU to install.
ATTENTION: if CWM asks you to install root or SuperSU, answer with NO, else you get a bootloop!
Now you can Restart, normal into the system.
That's it already, if you're in the system, you install this app from Play Store:
https://play.google.com/store/apps/details?id=com.jrummyapps.rootchecker
When you got root just update SuperSU and install busybox and you are good to go
Click to expand...
Click to collapse
THANKS btotaku! Just reporting back that this method works on T-Mobile's SM-N915T on 6.0.1 N915TUBU2DPG2. You generous information is highly appreciated! :good::good::good:

thanks alottttttttttttttt man it works on my N915T MM 6.0.1
btotaku said:
I rooted my phone following this procedure (the FY version of the Note Edge but should work for any other)
You need the following tools:
Samsung drivers:
https://www.dropbox.com/s/3d61st8zaxas4pt/SAMSUNG_USB_Driver_for_Mobile_Phones_1_5_6_0.exe?dl=0
Odin 3:09:
https://www.dropbox.com/s/ua0sqizz1m6558d/Odin3_v3.09.zip?dl=0
SuperSU 2.74:
https://download.chainfire.eu/964/SuperSU/BETA-SuperSU-v2.74-2-20160519174328.zip?retrieve_file=1
and CWM for the T version of the Note (from this thread):
http://forum.xda-developers.com/not...15s-n9150-cwm-based-recovery-6-0-5-1-t2954960
Move all files to a folder on the PC.
Copy the SuperSU your Cell (SD card int/ext).
Install the drivers for the phone.
Then go with the phone in the DL (download) mode.
Start Odin, connect the phone to the PC.
If Odin recognizes the cell phone continue.
Some side notes:
To get in DL (download) mode use key combination <VOL DOWN + HOME + POWER>.
To get in recovery mode use key combination <UP VOL + HOME + POWER>.
Press these buttons simultaneously.
You flash CWM in DL mode via Odin (in "AP" insert CWM) to the mobile phone.
It is important that you previously deactivate "Auto Reboot" in Odin.
When the flash process is finished, you just wait one minute after you have pressed the "Start", pull the cable from the phone and remove the battery.
Wait a couple seconds, and put the battery back inside.
Now, and this is important, you have to come directly into recovery mode.
If the phone starts normally into the system, CWM is overwritten with the standard recovery.
If you're in CWM, you go to "Install zip" and select the SuperSU to install.
ATTENTION: if CWM asks you to install root or SuperSU, answer with NO, else you get a bootloop!
Now you can Restart, normal into the system.
That's it already, if you're in the system, you install this app from Play Store:
https://play.google.com/store/apps/details?id=com.jrummyapps.rootchecker
When you got root just update SuperSU and install busybox and you are good to go
Click to expand...
Click to collapse
thumbs up bro ...ages ago i was trying to root my note edge T-Mobiles and now finally i found here the solution and i followed your mentioned steps and rooted N915T MM 6.0.1
thanks again!! keeep sharing and helping! :good:

this did not work for me, I think my bootloader is locked, how can I unlock it?

delson55 said:
this did not work for me, I think my bootloader is locked, how can I unlock it?
Click to expand...
Click to collapse
Which version have you got?

btotaku said:
I rooted my phone following this procedure (the FY version of the Note Edge but should work for any other)
You need the following tools:
Samsung drivers:
https://www.dropbox.com/s/3d61st8zaxas4pt/SAMSUNG_USB_Driver_for_Mobile_Phones_1_5_6_0.exe?dl=0
Odin 3:09:
https://www.dropbox.com/s/ua0sqizz1m6558d/Odin3_v3.09.zip?dl=0
SuperSU 2.74:
https://download.chainfire.eu/964/SuperSU/BETA-SuperSU-v2.74-2-20160519174328.zip?retrieve_file=1
and CWM for the T version of the Note (from this thread):
http://forum.xda-developers.com/not...15s-n9150-cwm-based-recovery-6-0-5-1-t2954960
Move all files to a folder on the PC.
Copy the SuperSU your Cell (SD card int/ext).
Install the drivers for the phone.
Then go with the phone in the DL (download) mode.
Start Odin, connect the phone to the PC.
If Odin recognizes the cell phone continue.
Some side notes:
To get in DL (download) mode use key combination <VOL DOWN + HOME + POWER>.
To get in recovery mode use key combination <UP VOL + HOME + POWER>.
Press these buttons simultaneously.
You flash CWM in DL mode via Odin (in "AP" insert CWM) to the mobile phone.
It is important that you previously deactivate "Auto Reboot" in Odin.
When the flash process is finished, you just wait one minute after you have pressed the "Start", pull the cable from the phone and remove the battery.
Wait a couple seconds, and put the battery back inside.
Now, and this is important, you have to come directly into recovery mode.
If the phone starts normally into the system, CWM is overwritten with the standard recovery.
If you're in CWM, you go to "Install zip" and select the SuperSU to install.
ATTENTION: if CWM asks you to install root or SuperSU, answer with NO, else you get a bootloop!
Now you can Restart, normal into the system.
That's it already, if you're in the system, you install this app from Play Store:
https://play.google.com/store/apps/details?id=com.jrummyapps.rootchecker
When you got root just update SuperSU and install busybox and you are good to go
Click to expand...
Click to collapse
Would this work with N915F International?
Thanks,

If we already have recovery do we still need to step backwards and install cwm, also do we just not let supersu update to 2.79 and leave it at 2.74 or 2.76?
I appear to only have partial root, none of the app's are [rompting me to grant or deny supersu.

Will this thing work is twrp latest recovery installed??

btotaku said:
I rooted my phone following this procedure (the FY version of the Note Edge but should work for any other)
You need the following tools:
Samsung drivers:
https://www.dropbox.com/s/3d61st8zaxas4pt/SAMSUNG_USB_Driver_for_Mobile_Phones_1_5_6_0.exe?dl=0
Odin 3:09:
https://www.dropbox.com/s/ua0sqizz1m6558d/Odin3_v3.09.zip?dl=0
SuperSU 2.74:
https://download.chainfire.eu/964/SuperSU/BETA-SuperSU-v2.74-2-20160519174328.zip?retrieve_file=1
and CWM for the T version of the Note (from this thread):
http://forum.xda-developers.com/not...15s-n9150-cwm-based-recovery-6-0-5-1-t2954960
Move all files to a folder on the PC.
Copy the SuperSU your Cell (SD card int/ext).
Install the drivers for the phone.
Then go with the phone in the DL (download) mode.
Start Odin, connect the phone to the PC.
If Odin recognizes the cell phone continue.
Some side notes:
To get in DL (download) mode use key combination <VOL DOWN + HOME + POWER>.
To get in recovery mode use key combination <UP VOL + HOME + POWER>.
Press these buttons simultaneously.
You flash CWM in DL mode via Odin (in "AP" insert CWM) to the mobile phone.
It is important that you previously deactivate "Auto Reboot" in Odin.
When the flash process is finished, you just wait one minute after you have pressed the "Start", pull the cable from the phone and remove the battery.
Wait a couple seconds, and put the battery back inside.
Now, and this is important, you have to come directly into recovery mode.
If the phone starts normally into the system, CWM is overwritten with the standard recovery.
If you're in CWM, you go to "Install zip" and select the SuperSU to install.
ATTENTION: if CWM asks you to install root or SuperSU, answer with NO, else you get a bootloop!
Now you can Restart, normal into the system.
That's it already, if you're in the system, you install this app from Play Store:
https://play.google.com/store/apps/details?id=com.jrummyapps.rootchecker
When you got root just update SuperSU and install busybox and you are good to go
Click to expand...
Click to collapse
Anyone can confirm this method still works for the T-mobile SM-N915T Note Edge running 6.0.1. Thanks.

Thanks for the very clear instructions especially your warning on cwm boot loop. I was able to root my note edge sm-n915f without problems.

The links for the files to download seems to have expired. Can someone post them again? Thanks!

mrcds08 said:
The links for the files to download seems to have expired. Can someone post them again? Thanks!
Click to expand...
Click to collapse
Just google the stuff you don't have and you can find it

princehpk said:
Will this thing work is twrp latest recovery installed??
Click to expand...
Click to collapse
it works for me, just update superSU

Will this work on a Note Edge SM-N915T, N915US2DQG1. Thanks in advance....

Chainfire root method

Hi, I've tried a few tutorials on this forum on how to root the Samsung Galaxy S7 G930f.
After flashing the chainfire autoroot file my device stays stuck on the Samsung logo I've waited over 1 hour for the device to boot but it does not.
My question is can anyone explain what I could be doing wrong my device is on stock nougat I did root successfully with magisk a couple of months back but was not happy with having to format my data.
I also prefer chainfire SuperSu. Any help would be appreciated. Thanks

I also had the same problem. So, I did the old fashioned way.
1. Download TWRP.tar from here: https://dl.twrp.me/herolte/
2. Download the latest stable SuperSU zip. If you want the link: Here ya go
2. Instead of flashing the CFAutoroot file, open Odin, click on AP and select the TWRP that you downloaded.
3. Once it flashes successfully, power off the phone, then Press and hold Volume Up+Home+Power Button to get into the recovery.
4. Copy the SuperSU and flash it and Viola! You got SuperSU!
You probably knew steps 3,4 but I wrote them just in case

hi may I know if you reformat your data after step 4?

muloarell said:
hi may I know if you reformat your data after step 4?
Click to expand...
Click to collapse
Well, yeah. I always start with a clean slate. Just a habit i picked up when i had a OnePlus One. You should be fine without a format though...Cause you're just rooting, not flashing a whole new ROM.

Thanks for helping me out, unfortunately after flashing twrp and booting into twrp recovery the default android recovery loads up.
I will continue searching for a method that does work. If you know anything else I could try please let me know.

AndroidOmenon said:
Thanks for helping me out, unfortunately after flashing twrp and booting into twrp recovery the default android recovery loads up.
I will continue searching for a method that does work. If you know anything else I could try please let me know.
Click to expand...
Click to collapse
That's weird, I just flashed stock firmware and TWRP a few mins ago and it worked fine for me. I hope you used the .tar and not the .img and the Odin that comes with CF Auto Root, not the one you use to flash the whole stock firmware.

I did use the .tar and have also tried with Odin that comes with cf autoroot.
Unfortunately I still get the same result flash of twrp is successful when I boot into recovery I get the android installing update with dead android then it just goes into to stock recovery.
I will try a few more times if no success I'll try with a fresh install of stock firmware.
Thanks for the help though appreciate it.

I decided to try again and succeeded but still had to format data to get the phone to boot. I made a full backup on my laptop before proceeding I did the following steps to successfully root.
I am in no way responsible for any lost data or bricked devices please note if you follow this tutorial you will trip knox and your warranty will be void.
1. MAKE A FULL BACKUP OF YOUR DEVICE CAN'T BE STRESSED ENOUGH
2. Flash the latest SM-G920F firmware with odin.
3. Setup device let it check for software updates, install the update if available (I had an update)
4. Download latest twrp recovery in .tar format for the SM-G920F from twrp website
5. Download the latest stable version of SuperSU.zip
6. Download Samsung Antiroot Removal Kit
7. Transfer the files to your SM-G920F sd card
8. Power off your SM-G920F and enter download mode by holding the volume down + home button + power button read the warning press up to allow custom flashing.
9. Open Odin I used Odin v3.12.3 tap the AP button locate the custom recovery and flash it's done be ready to enter twrp recovery as the device will boot quickly, as soon as it powers off to reboot hold the volume up + home button + power button if timed correctly you shall enter twrp recovery.
10. Locate the SuperSU.zip install it but don't reboot
11. Locate the Samsung Antiroot Removal Kit and install it
12. Go back in twrp go to the format option and select format data once formatted reboot the device.
It will take some time to boot once it's rebooted you will have a rooted SM-G920F with SuperSU

AndroidOmenon said:
I decided to try again and succeeded but still had to format data to get the phone to boot. I made a full backup on my laptop before proceeding I did the following steps to successfully root.
I am in no way responsible for any lost data or bricked devices please note if you follow this tutorial you will trip knox and your warranty will be void.
1. MAKE A FULL BACKUP OF YOUR DEVICE CAN'T BE STRESSED ENOUGH
2. Flash the latest SM-G920F firmware with odin.
3. Setup device let it check for software updates, install the update if available (I had an update)
4. Download latest twrp recovery in .tar format for the SM-G920F from twrp website
5. Download the latest stable version of SuperSU.zip
6. Download Samsung Antiroot Removal Kit
7. Transfer the files to your SM-G920F sd card
8. Power off your SM-G920F and enter download mode by holding the volume down + home button + power button read the warning press up to allow custom flashing.
9. Open Odin I used Odin v3.12.3 tap the AP button locate the custom recovery and flash it's done be ready to enter twrp recovery as the device will boot quickly, as soon as it powers off to reboot hold the volume up + home button + power button if timed correctly you shall enter twrp recovery.
10. Locate the SuperSU.zip install it but don't reboot
11. Locate the Samsung Antiroot Removal Kit and install it
12. Go back in twrp go to the format option and select format data once formatted reboot the device.
It will take some time to boot once it's rebooted you will have a rooted SM-G920F with SuperSU
Click to expand...
Click to collapse
how did you backup your files on step 1 if your not rooted?

This is how I backed up my phone it's a bit tedious could have been done quicker.
First I removed my memory card from the phone. I then connected my phone in MTP mode to my laptop I dragged the folder of the files I needed to my laptop.
I then used MobileGo to export .apk files of the apps I wanted. I then exported the photos and videos I wanted to keep.
I did a WhatsApp backup copied the folder to my laptop.
I then made accounts on all games that I wanted to keep my progress on using Facebook and Google Play. Some games allows signing up with email address.
I used Mcbackup to backup all my contacts and e mailed them to myself.
I know that I could have used Google Drive or Samsung Cloud for some of the tasks but I prefer backing up this way.

Root SM-N910T loops

I've tried to root my phone using this procedure:
How to root Samsung Note 4 SM-N910T and after I used Obi3 to load CF-Auto-Root.tar file, phone went to this page:
RECOVERY BOOTING.....
RECOVERY IS NOT SEANDROID ENFORCING
Set Warranty Bit : recovery
Click to expand...
Click to collapse
And whatever I do it boots only in this page now...
Is it any way to recover from this?
Thank you in advance!

This is very serious problem. Phone starts only with the screen mentioned in my first post. There is no Android Recovery available (if I press VolumeUP+Power+Home it goes to the same screen only). I can only go to Download mode and try to update it with CF-Auto-Root.tar file. But it doesn't help. Phone boots only into one screen only and there is no way to bypass it now.
Please help!

Do not ever use the procedure from the site, mentioned in my first post! It's full of BS (to go to Download mode you have to press VolumeDOWN+Home+Power and not VolumeUP+Home+Power) and the file provided there will soft-brick your phone with endless loop as I've described above
Here is the proper procedure to root SM-N910T phone:
1. Download and install Samsung USB driver Samsung-Usb-Driver-v1.5.63.0
2. Download and extract CF-Auto-Root-trltetmo-trltetmo-smn910t.tar.md5 file. See list of all devices - CF-Auto-Root
3. Turn off phone and boot into Download mode. Press VolumeDWN+Home+Power buttons
4. In Download mode if you see warning yellow triangle, then press VoumelUP to continue
5. Run (as admin) Odin3 and connect phone to computer
6. Once device is detected, click on AP button and select CF-Auto-Root-trltetmo-trltetmo-smn910t.tar.md5 file
7. Wait for couple minutes until rooting is completed and you see PASS! becoming green on top
Now you phone will boot normally and will set its root

ROOT J2 PRIME (SM-G532 F/M/G) SUPEREASY 5 steps

now i was looking for how to root my j2 prime because its what i use to login with my vpn then i use a proxy server on it to route all traffic connected to it while its in hotspot mode but it seems proxy servers have their limitations and so im forced to root so i can just hotspot the vpn directly with an app, but after searching i found 3 methods all using superSU which im not comfortable with anymore, all with many steps but in my experice since this phone has got nothing to lose i decided to experiment and boom it worked...
what you need
latest Magsisk - v17.1 at this time of posting
latest SAMSUNG USB DRIVERS
ODIN
and TWRP by
ashyx said:
STEPS
1. BOOT PHONE IN DOWNLAOD MODE (power+vold-down+home)
2. FLASH TWRP in the AP OPTION in ODIN (untick auto reboot;very important) then after flash succeeds
3. Pull out battery and boot to recovery (power+vol-up+home)
4. FLASH MAGISK.zip from your SDCARD (Recovery wont be able to mount internal storage so make sure to put the MAGISK.zip in your SDCARD)
5. Reboot and Hello systemless root
credits to this thread where i was searching for root, includes link to 3 methods but mine is the shortest and easiest
Click to expand...
Click to collapse

I'm unable to start recovery mode. I pull out the battery and after pressing the keys the phone simply goes off. Also I'm unable to enter recovery mode anyway (after turning it off and not flashing anything). That's it, I can't enter stock recovery either.
I tried all button combinations and it just doesn't enter recovery mode.
Never mind, it was probably a faulty button. Pressing with force did the trick. I however employed a bit different path (or perhaps I wrote it down more detailed), which come out more noob like, I'll leave them here for anyone that might use them
Noob, baby steps to root the Samsung Galaxy J2 Prime SM-G532M:
1. Enable developer mode and selected OEM unlocking and USB debug, dunno if it's needed but I did it because in all roots I have seen this is a must.
2. Put the Magisk zip onto a SD card (currently Magisk-v18.0) and put the SD card into the phone. Then I turned off the phone.
3. Turn on the phone into download mode (power+vold-down+home), connect the phone to the PC.
4. Open ODIN and FLASH TWRP file using the AP button (VERY IMPORTANT, uncheck the auto reboot in options, otherwise the recovery goes back to stock I think and the phone will boot into the regular OS, and you'll have to flash TWRP again), wait a few seconds to the flash to finish (odin says PASS! in green).
5. From this screen without touching anything reboot the phone into recovery mode (power+vol-up+home) (just in case press hard the vol+ key). If it boots the phone in regular mode, do steps 2 , 3 and 4 again.
6. FLASH MAGISK.zip from the microSD. When finished wipe Delvik/Cache.
7. Reboot the system. Open the Magisk app (you might have to wait a few seconds for it to appear among on the apps) then press yes when prompted to finish installation as many times (2 times I think). And done, you have your phone rooted.
PD: Magisk can be found here: https://github.com/topjohnwu/Magisk/releases/
As for the TWRP file (twrp_3.1.0-1_sm-g532_5617b.tar), use the one in the link on the OP.

LordBaal19 said:
6. FLASH MAGISK.zip from the microSD. When finished wipe Delvik/Cache.
7. Reboot the system. Open the Magisk app (you might have to wait a few seconds for it to appear among on the apps) then press yes when prompted to finish installation as many times (2 times I think). And done, you have your phone rooted..
Click to expand...
Click to collapse
why am i getting an error? it says
"Updater process ended with ERROR: 1
Error installing zip file '/external_sd/Magisk-v17.1.zip' "
can i get some help here?

Good day!
Is disabling dm-verity and force encryption included in the process?
And also, everything works fine but how is that i cannot delete system apps manually? They're returning back after reboot.
Thanks.

Unable to detect the phone -win nor Lin
Hello guys
Something really extrange is happening.
My j2 prime -532G- can't be detected by Windows nor Linux.
The usb is working because it charges the phone, but I can't access the phone at all. I checked all the drivers in Win -google/adb and samsung- and in Linux libmtp/heimdall/etc.
I have tryed different usb -not the original one since i lost it-
Even when i start the download mode, nothing happens.
it there a way to root the phone without a PC? i have tryed also kingroot apk but it is useless.
Thanks

LordBaal19 said:
I'm unable to start recovery mode. I pull out the battery and after pressing the keys the phone simply goes off. Also I'm unable to enter recovery mode anyway (after turning it off and not flashing anything). That's it, I can't enter stock recovery either.
I tried all button combinations and it just doesn't enter recovery mode.
Never mind, it was probably a faulty button. Pressing with force did the trick. I however employed a bit different path (or perhaps I wrote it down more detailed), which come out more noob like, I'll leave them here for anyone that might use them
Noob, baby steps to root the Samsung Galaxy J2 Prime SM-G532M:
1. Enable developer mode and selected OEM unlocking and USB debug, dunno if it's needed but I did it because in all roots I have seen this is a must.
2. Put the Magisk zip onto a SD card (currently Magisk-v18.0) and put the SD card into the phone. Then I turned off the phone.
3. Turn on the phone into download mode (power+vold-down+home), connect the phone to the PC.
4. Open ODIN and FLASH TWRP file using the AP button (VERY IMPORTANT, uncheck the auto reboot in options, otherwise the recovery goes back to stock I think and the phone will boot into the regular OS, and you'll have to flash TWRP again), wait a few seconds to the flash to finish (odin says PASS! in green).
5. From this screen without touching anything reboot the phone into recovery mode (power+vol-up+home) (just in case press hard the vol+ key). If it boots the phone in regular mode, do steps 2 , 3 and 4 again.
6. FLASH MAGISK.zip from the microSD. When finished wipe Delvik/Cache.
7. Reboot the system. Open the Magisk app (you might have to wait a few seconds for it to appear among on the apps) then press yes when prompted to finish installation as many times (2 times I think). And done, you have your phone rooted.
PD: Magisk can be found here: https://github.com/topjohnwu/Magisk/releases/
As for the TWRP file (twrp_3.1.0-1_sm-g532_5617b.tar), use the one in the link on the OP.
Click to expand...
Click to collapse
I can't seem to get this phone to go into recovery after flashing TWRP. It always goes into a normal reboot no matter how hard i press the button combination.
Any idea about how to make it reboot to recovery any other way
BTW I was aable to make it go to TWRP Once but forgot to insert the SD card that time and had to repeat the process again and haven't been able to see that TWRP screen agin
Any ideas

mbalino said:
Win -google/adb and samsung- and in Linux libmtp/heimdall/etc.
Click to expand...
Click to collapse
Hello mbalino I am new to XDA forums
Where did you checked the drivers in the phone or the PC? what drivers are they?

mbalino said:
My j2 prime -532G- can't be detected by Windows nor Linux.
The usb is working because it charges the phone,
Click to expand...
Click to collapse
Did the phone trigger an Autoplay window (to ask you if you want "view files", "import media", etc.)
Did the phone appear in the file explorer (as a media player device?) with storage(s)?

Basic guide to Installing TWRP, Root and ROM via ODIN on S7 amd S7 edge

Hey everyone.
I have recently rooted and installed the Pixel experience 9 custom ROM on my S7 edge.
Even though I am confident in Installing ROMs and using TWRP I always like to have a check on the net to see the best way of doing stuff. When checking I found that there were so many different guides that the process became more confusing than it needed to be and it caused issues when I was trying install the ROM.
So I have decided to write out a guide to help everyone in the future.
Note. I am in UK using a Exynos version of the S7 edge. I believe there is a complication with the USA Snapdragon version.
Also this is done at your own risk and I am not responsible for any damage, errors or bricked devices. This will also void the warranty of your device.
What will you need
1. A computer with a SD card slot (if you don't have a slot you can usb a usb adaptor)
2. The latest version of ODIN
3. Your chosen ROM zip
4. Magisk Root zip
5. The correct TWRP file for your S7 or S7 edge
6.The latest version of your Stock firmware (this is in case something goes wrong)
7. A spare micro SD card with SD card adaptor
8. Micro USB cable (charging cable usually does the job)
9. Samsung Device drivers
This guide will be split in to 4 parts with some additional notes at the end.
Part 1- on your PC
Part 2- on your mobile
Part 3- In ODIN mode
Part 4- In TWRP
On your PC
1. Download and install the latest version of ODIN to your PC. https://samsungodin.com/
2. Download and install the Samsung Device drivers.
3. Download the correct TWRP version for your phone. https://twrp.me/
4. Now Download your root file, I used to Magisk root but there is super SU as well. I was told that Super SU is dated compared to Magisk.
https://www.xda-developers.com/magisk-v17-1-android-pie-a-b-support/
5. Now download your chosen ROM. There is lots of different ROMs for the S7 and S7 edge. In my case I decided to go with Pixel experience 9, it's basically a Pixel 3 ROM that runs Android P but it's up to you.
6. Go to Sammobile and download the stock Firmware for your device. The download takes ages so I would just leave this download in the background and continue to the next step (You shouldn't need this file but you will need it something goes wrong)
https://www.sammobile.com/firmwares/
7. Put your micro SD into your adaptor then insert into your PC into your SD card slot, then copy the ROM Download and the Root download SD card to the card.
8. Open ODIN and put the TWRP file on the AP section, then uncheck re-partition.
On Your Phone.
1. Before plugging up to the PC there are something to do first. The first thing to do is enter developer options by taping build number 7 times. Then check USB debugging and then check OEM unlocking.
2. Back up your data with Samsung backup and Google backup, both found in the settings.
3. If you already have a SD card inside your phone remove it and put it somewhere safe.
4. Power off your device and Boot in to ODIN mode (volume down, home button and power at the sametime)
In ODIN mode (READ THIS CAREFULLY)
1. BEFORE pressing start on your computer, hold volume up and home button.
2. Now press start on the computer, keep your fingers on the volume button up button and home button. Let the PC and Phone start it's process.
3. The moment the phone screen goes black. Press and hold the power but while keeping your fingers on the volume up and home button.
4. Keep all the buttons held down (volume up, home button and power button) till you see the TWRP screen boot.
In TWRP.
1. Once TWRP boots you will see a screen it will say "swipe to allow modifications" DON'T swipe just press "read only"
2. Press wipe and then press format data. Once the wipe is complete DO NOT swipe to reboot. (You will get yourself stuck in a boot loop) press the TWRP home icon instead.
3. Press Reboot then press recovery this will complete the installation of TWRP (if you press anything else you will get stuck in a boot loop)
4. Allow TWRP to reboot. You will be presented with the "swipe allow modifications" check the do not show again box and swipe.
5. Now insert your Micro SD card with the downloaded files.
6. Press wipe, then press advanced and check cashe and
dalvik cashe. Then Press TWRP Home icon
7. Press install and navigate to SD card. Then press the on the Magisk file and swipe, allow the process to finish and press wipe cache and Dalvik cashe.
8. Press TWRP home icon and press install and navigate back to SD card. Then press your ROM file and swipe again. Once it's finished press wipe cashe and Dalvik cashe. Then swipe to reboot.
9. Re-insert your memo card you were using before. (Not the one with the downloads on, the one with your photos and music and stuff)
10. BOOM your done. Happy days with your new ROM.
Few last things
the ROM I installed had G-apps preinstalled with the ROM, but if your ROM has no G-apps then once you booted, download G-apps from your ROMs browser and flash them with TWRP.
If you get stuck in a boot loop use your stock firmware file and Odin to reinstall the stock firmware and try the whole process again.
This method uses SD card to install the files in TWRP but I believe you can just copy the files via your PC directly to your phone at point 5 in the TWRP part of the guide. I had a spare card so I used a card.
The principal of this guide can be applied to other Samsung devices but newer device then the S7 and S7 edge have more factors to take note of, so some research will be required.
Remember
this is done at your own risk and I am not responsible for any damage, errors or bricked devices. This will also void the warranty of your device.
Hope this guide works well for you.

Is the "no verty" not required to remove encryption?

ctbale said:
Is the "no verty" not required to remove encryption?
Click to expand...
Click to collapse
I don't think this was a big issue with S7E but I know the S8 and onwards have extra encryption protection and 24 hour jailbait locks.
I have rooted my S7E a few times and it's never been an issue for me.
Sometimes the USA Snapdragon versions have extra encryption as well.

Thanks for reply.
In a few days I will try to root.
Fingers Crossed!
( I do have the Exynos S7 Edge G935F)
Also have a newer stock Oreo 8.0.0, unrooted. Thats the part I hear is giving people problems. Something about after flashing TWRP you get a fail to mount the data partition .... or something like that. Something to do with quotas

Heimdell vs odin
I wonder why most people use odin.
The official lineage OS installation instruction recommends heimdell. https://wiki.lineageos.org/devices/hero2lte/install
So what is the difference ? Heimdell vs odin

ZionMainframe said:
I wonder why most people use odin.
The official lineage OS installation instruction recommends heimdell. https://wiki.lineageos.org/devices/hero2lte/install
So what is the difference ? Heimdell vs odin
Click to expand...
Click to collapse
ODIN is made by Samsung developers and Hiemdell is a 3rd party option. They both do the same thing but some say that Heimdell is safer, easier and faster.
Personally I use Odin because I have got used to it and it has never let me down.
I mostly use it to install Stock UK firmware on cheaper Samsung phones that are from overseas.

Hello,
Thanks for your guide but I think there are too much steps, you can do it easier.
You can keep your sd card in the phone to transfer the ROM and magisk.
You can uncheck reboot in Odin instead doing this hard combination of "keep pressing volume up and power + press start on your computer at the same time", or let reboot checked, pressing start and keep pressing power+home+volume up when the screen turning off.
Even if you're in a bootloop, you can go back in recovery by forcing the phone to reboot (power+home+volume down) and when you see the Samsung logo (splahscreen) you keep pressing power+home+volume up until you see twrp screen appears.
Sorry men, it's not against you or your guide but to help beginners, we are always scared when we see a long and complicate list of steps, especially when we don't know.
But it's nice to share the links of the necessary tools to avoid searching everywhere :good:
And don't worry guys, if you do something wrong you can easily restore the stock firmware, it's very hard to brick a Samsung device, just be sure to get the last version of TWRP for the good model and the ROM corresponding to this model too.
I flashed my S7Edge the day I bought it without stress, take your time, read the tutorials and try to understand what you are going to do before doing it and all will be fine.
The simple version (IDK if it's better) is :
1 : Install Samsung drivers
2 : Copy ROM + magisk + noverity zips on sdcard
3 : Go into download mode (Power off phone and keep pressing power+home+volume down until the blue screen and follow the steps on the screen)
4 : Open Odin (last version), connect your phone to the computer, uncheck reboot box and flash TWRP on AP case
5 : Reboot on TWRP (keep pressing power+home+volume down until you see Samsung logo, and directly keep pressing power+home+volume up until you see TWRP screen)
6 : Wipe everything except sdcard + format data + (optionally) flash noverity zip
7 : Flash the ROM
8 : Reboot to system, configure the rom and wait some minutes to let the ROM create dalvik cache.
9 : Reboot normally and wait some minutes.
10 : Reboot to TWRP
11 : Flash Magisk zip (IMPORTANT ! Don't Flash Magisk just after the ROM, first boot on the ROM without root and reboot one time at least before to avoid lags in the system due to dalvik cache ! Steps 7 and 8)
12 : Reboot to system and install magisk manager apk
13 : I'm not superstitious but there is not step 13, you are done, enjoy !
Don't forget, don't flash Magisk directly after the ROM or you'll get a laggy ROM.
Just boot without flashing magisk and let the ROM doing his work in background during some minutes (5 to 10 minutes should be good), and do another reboot.
After that you can flash Magisk.
Use links shared by the creator of this topic, they are the officials. :victory:

psylooooo said:
Hello,
Thanks for your guide but I think there are too much steps, you can do it easier.
You can keep your sd card in the phone to transfer the ROM and magisk.
You can uncheck reboot in Odin instead doing this hard combination of "keep pressing volume up and power + press start on your computer at the same time", or let reboot checked, pressing start and keep pressing power+home+volume up when the screen turning off.
Even if you're in a bootloop, you can go back in recovery by forcing the phone to reboot (power+home+volume down) and when you see the Samsung logo (splahscreen) you keep pressing power+home+volume up until you see twrp screen appears.
Sorry men, it's not against you or your guide but to help beginners, we are always scared when we see a long and complicate list of steps, especially when we don't know.
But it's nice to share the links of the necessary tools to avoid searching everywhere :good:
And don't worry guys, if you do something wrong you can easily restore the stock firmware, it's very hard to brick a Samsung device, just be sure to get the last version of TWRP for the good model and the ROM corresponding to this model too.
I flashed my S7Edge the day I bought it without stress, take your time, read the tutorials and try to understand what you are going to do before doing it and all will be fine.
The simple version (IDK if it's better) is :
1 : Install Samsung drivers
2 : Copy ROM + magisk + noverity zips on sdcard
3 : Go into download mode (Power off phone and keep pressing power+home+volume down until the blue screen and follow the steps on the screen)
4 : Open Odin (last version), connect your phone to the computer, uncheck reboot box and flash TWRP on AP case
5 : Reboot on TWRP (keep pressing power+home+volume down until you see Samsung logo, and directly keep pressing power+home+volume up until you see TWRP screen)
6 : Wipe everything except sdcard + format data + (optionally) flash noverity zip
7 : Flash the ROM
8 : Reboot to system, configure the rom and wait some minutes to let the ROM create dalvik cache.
9 : Reboot normally and wait some minutes.
10 : Reboot to TWRP
11 : Flash Magisk zip (IMPORTANT ! Don't Flash Magisk just after the ROM, first boot on the ROM without root and reboot one time at least before to avoid lags in the system due to dalvik cache ! Steps 7 and 8)
12 : Reboot to system and install magisk manager apk
13 : I'm not superstitious but there is not step 13, you are done, enjoy !
Don't forget, don't flash Magisk directly after the ROM or you'll get a laggy ROM.
Just boot without flashing magisk and let the ROM doing his work in background during some minutes (5 to 10 minutes should be good), and do another reboot.
After that you can flash Magisk.
Use links shared by the creator of this topic, they are the officials. :victory:
Click to expand...
Click to collapse
Cheers for helping my out, my guide has a lot of steps as I literally wrote what I did every step.
I was going for a guide that spelt out every single detail for the less experienced people. I glad to see you approve of my links.
Great guide though, great that both guides can complement each others.

Owenboy89 said:
Cheers for helping my out, my guide has a lot of steps as I literally wrote what I did every step.
I was going for a guide that spelt out every single detail for the less experienced people. I glad to see you approve of my links.
Great guide though, great that both guides can complement each others.
Click to expand...
Click to collapse
You are right ! And your guide is more complete than mine, I don't talk about going into developers options to enable oem unlock etc, I wrote this too fast and too late :laugh:

Does this process work for latest March 1 2019 security patch?
Build number is G935FXXS4ESC6.
Thanks!

stenoo said:
Does this process work for latest March 1 2019 security patch?
Build number is G935FXXS4ESC6.
Thanks!
Click to expand...
Click to collapse
It does work
https://www.mediafire.com/folder/ka5kcad3w7awo/S7+

Hey are you sure it doesn't work for snapdragon?

SULkiller said:
Hey are you sure it doesn't work for snapdragon?
Click to expand...
Click to collapse
You can use this method for Snapdragon, but Snapdragon phones in certain regions have a built jailbreak that can complicate things. There are ways around it but as I am in a region that sell exynos then i have no experience with the Snapdragon Variant. ?

hey when i try flash galaxy s7edge sm-g935f with twrp when i go into recovery it red screen what am i doing wrong cheers inadvance
3 time flashing stock grrrrrrrrr

1337-oxide said:
hey when i try flash galaxy s7edge sm-g935f with twrp when i go into recovery it red screen what am i doing wrong cheers inadvance
3 time flashing stock grrrrrrrrr
Click to expand...
Click to collapse
When you booted into recovery the for the first time after installing it, did you wipe all your data??
Then go into reset and pressed reset to recovery???

Owenboy89 said:
When you booted into recovery the for the first time after installing it, did you wipe all your data??
Then go into reset and pressed reset to recovery???
Click to expand...
Click to collapse
i got twrp and root know ressuruction remix giving me error 7 i think what does that mean
cheers
---------- Post added at 04:40 PM ---------- Previous post was at 04:35 PM ----------
sorry but know i lost twrp what am i doing wrong SM-G935F s7edge

is anyone going to help me or u just like the other sites dont reply i need this info asap its only reason i rooted was to use custom rom oh also turmux

Hey
Sorry I have been busy.
Best option is to flash the firmware and start again. Follow the steps of original comment.
Remember when you boot in to TWRP straight after installing it...then wipe all your data then press reboot and reboot back into RECOVERY....once your done this you have completed the install of TWRP.
Once that is all done....wipe your cashe davalik data and then insert your memory card with the custom Rom and Magisk root inside. Install Magisk first...then the ROM.
Once this is done wipe cashe/davalik data once more and reboot, your custom ROM should load up...once the ROM loads install the Magisk root manager and latest update for the root.
Other things to check have you installed the correct TWRP and correct custom Rom for your device.
Also check your customs ROM feed on XDA to see if anyone has issued like this on there as well, if so there might be specific answer to your issue there.
Hope this helps sorry for the delay

How can you switch back to root version of rom for Samsung Galaxy S7 Edge
You can install original ROM / firmware of Samsung Galaxy S7 Edge follow these simple steps :
1. Download and install the latest SamsungOdin 3 software
2. Now download ROM of S7 edge from sammobile.com .
3. Switch off your phone and connect your phone with PC using data cable.
4. Press Power+Vol down and home key together.
5. Now select recovery from your phone boost setup.
6. Open the Odin and select your phone and browse the ROM file.
7. Now press install ROM. Almost done!
8. Wait to complete installation it may take 10 - 15 minutes.
9. Enjoy!

psylooooo said:
Hello,
Thanks for your guide but I think there are too much steps, you can do it easier.
You can keep your sd card in the phone to transfer the ROM and magisk.
You can uncheck reboot in Odin instead doing this hard combination of "keep pressing volume up and power + press start on your computer at the same time", or let reboot checked, pressing start and keep pressing power+home+volume up when the screen turning off.
Even if you're in a bootloop, you can go back in recovery by forcing the phone to reboot (power+home+volume down) and when you see the Samsung logo (splahscreen) you keep pressing power+home+volume up until you see twrp screen appears.
Sorry men, it's not against you or your guide but to help beginners, we are always scared when we see a long and complicate list of steps, especially when we don't know.
But it's nice to share the links of the necessary tools to avoid searching everywhere :good:
And don't worry guys, if you do something wrong you can easily restore the stock firmware, it's very hard to brick a Samsung device, just be sure to get the last version of TWRP for the good model and the ROM corresponding to this model too.
I flashed my S7Edge the day I bought it without stress, take your time, read the tutorials and try to understand what you are going to do before doing it and all will be fine.
The simple version (IDK if it's better) is :
1 : Install Samsung drivers
2 : Copy ROM + magisk + noverity zips on sdcard
3 : Go into download mode (Power off phone and keep pressing power+home+volume down until the blue screen and follow the steps on the screen)
4 : Open Odin (last version), connect your phone to the computer, uncheck reboot box and flash TWRP on AP case
5 : Reboot on TWRP (keep pressing power+home+volume down until you see Samsung logo, and directly keep pressing power+home+volume up until you see TWRP screen)
6 : Wipe everything except sdcard + format data + (optionally) flash noverity zip
7 : Flash the ROM
8 : Reboot to system, configure the rom and wait some minutes to let the ROM create dalvik cache.
9 : Reboot normally and wait some minutes.
10 : Reboot to TWRP
11 : Flash Magisk zip (IMPORTANT ! Don't Flash Magisk just after the ROM, first boot on the ROM without root and reboot one time at least before to avoid lags in the system due to dalvik cache ! Steps 7 and 8)
12 : Reboot to system and install magisk manager apk
13 : I'm not superstitious but there is not step 13, you are done, enjoy !
Don't forget, don't flash Magisk directly after the ROM or you'll get a laggy ROM.
Just boot without flashing magisk and let the ROM doing his work in background during some minutes (5 to 10 minutes should be good), and do another reboot.
After that you can flash Magisk.
Use links shared by the creator of this topic, they are the officials. :victory:
Click to expand...
Click to collapse
Your certainly not wrong there. confusing isn't the word I would choose more like frustrating to hell. I'm new to this and I can't even get out the starting gate lol every time I move one step forward I move two steps back and that's no joke.
I can't read any more tutorials there coming out my ears it's just adding to the confusion I'm completely lost now. can't even pick a custom rom that's a headache for another time I was just wanting to root the phone but was told stock roms are temperamental and custom roms was the way forward. all I keep reading is tutorials telling you to down load files but never a mentioning once if they should be in zip format as downloaded or unpacked? then providing links to other files taht are in apk file! like Magisk. but continue to about the file as though it were a zip! as noob it's frustrating to keep asking for help and every key stroke at least for me anyway you feel like a pain in the rear! so for now I'm throwing in the towel at least I know one thing that works. giving up lol.