Related
Hi im new to these forums
Anyway, on my HTC i am currently stuck on the bootloader screen. If I press recovery or anything it just shows the "HTC" logo screen and boots back to the bootloader. What do I do anyone? I think my ROM has been wiped
BilalH said:
Hi im new to these forums
Anyway, on my HTC i am currently stuck on the bootloader screen. If I press recovery or anything it just shows the "HTC" logo screen and boots back to the bootloader. What do I do anyone? I think my ROM has been wiped
Click to expand...
Click to collapse
Hi,
Are you s-off?
Did you wipe your old ROM?
What have you done?
What are you trying to do?
A little more information is quite useful to those who want to help...
malybru said:
Hi,
Are you s-off?
Did you wipe your old ROM?
What have you done?
What are you trying to do?
A little more information is quite useful to those who want to help...
Click to expand...
Click to collapse
Hi
I'm S-ON.
I think I accidently wiped my old rom
Im trying to get back to the stock ROM i Just want my phone working agian.
BilalH said:
Hi
I'm S-ON.
I think I accidently wiped my old rom
Im trying to get back to the stock ROM i Just want my phone working agian.
Click to expand...
Click to collapse
flash an RUU - go into hboot and find out what ROM version you were running before (by using fastboot getvar mainversion) then find an RUU with the same or higher version number and download then run it.
BilalH said:
Hi
I'm S-ON.
I think I accidently wiped my old rom
Im trying to get back to the stock ROM i Just want my phone working agian.
Click to expand...
Click to collapse
Jonny said:
flash an RUU - go into hboot and find out what ROM version you were running before (by using fastboot getvar mainversion) then find an RUU with the same or higher version number and download then run it.
Click to expand...
Click to collapse
Hi when I put in "fastboot getvar mainversion" in command prompt it says
C:\Users\amd>fastboot getvar mainversion
getvar:mainversion FAILED < remote: unknown command >
finished. total time: 0.008s
I was currently using official fw 4.0.3 with sense 3.6 before
BilalH said:
Hi when I put in "fastboot getvar mainversion" in command prompt it says
C:\Users\amd>fastboot getvar mainversion
getvar:mainversion FAILED < remote: unknown command >
finished. total time: 0.008s
I was currently using official fw 4.0.3 with sense 3.6 before
Click to expand...
Click to collapse
Then your safe just to download the 3.33.401.6 RUU and it should flash no problems
BilalH said:
Hi
I'm S-ON.
I think I accidently wiped my old rom
Im trying to get back to the stock ROM i Just want my phone working agian.
Click to expand...
Click to collapse
Hi,
As has been mentioned, flashing a RUU will get you back to a working phone.
Look HERE
Jonny said:
Then your safe just to download the 3.33.401.6 RUU and it should flash no problems
Click to expand...
Click to collapse
Ah thanks Il give this a try, previously Ive tried download 3.32 RUU's and theyve all said its the wrong version. Downloading from filefactory right now, taking a long time unfortuantly, 2 hours Thanks
Just downloading this RUU
RUU_PYRAMID_ICS_HTC_Europe_3.33.401.6_Radio_11.76A.3504.00U_11.24A.3504.31_M_release_266171_signed.exe
Hi
I tried the RUU and get the following error
ERROR [130]: MODEL ID ERROR
The ROM Update Utility cannot update your android phone.
Please get the correct ROM Update Utitlity and try again.
My current RUU says im on 3.32.206.112 and I pressed update, the update went on for a while and this error popped up.
BilalH said:
Hi
I tried the RUU and get the following error
ERROR [130]: MODEL ID ERROR
The ROM Update Utility cannot update your android phone.
Please get the correct ROM Update Utitlity and try again.
My current RUU says im on 3.32.206.112 and I pressed update, the update went on for a while and this error popped up.
Click to expand...
Click to collapse
Hi,
You are using the wrong RUU.
Check the link I gave you earlier to find your CID,and the correct RUU,and how to install it.
malybru said:
Hi,
You are using the wrong RUU.
Check the link I gave you earlier to find your CID,and the correct RUU,and how to install it.
Click to expand...
Click to collapse
Hi thhere been searching trying to find my RUU but I cant seem to find it
My CID is 02_001, therefore o2
CAn you link me to the RUU I need? Thanks
BilalH said:
Hi thhere been searching trying to find my RUU but I cant seem to find it
My CID is 02_001, therefore o2
CAn you link me to the RUU I need? Thanks
Click to expand...
Click to collapse
Hi,
Have you tried taking a general European RUU and Adding your CID to the PGIMG.zip
It is 4.2 in the guide.
malybru said:
Hi,
Have you tried taking a general European RUU and Adding your CID to the PGIMG.zip
It is 4.2 in the guide.
Click to expand...
Click to collapse
Hi Ive tried following the method.
when I get up to the part where you have to type 'fastboot flash zip PG58IMG.zip it says this:
C:\android-sdk-windows\tools>fastboot flash zip PG58IMG.zip
sending 'zip' <432384 KB>...
OKAY [56.745s]
writing 'zip'...
(bootloader) signature checking...
FAILED (remote: 12 signature fail)
finished. total time: 130.818s
BilalH said:
Hi Ive tried following the method.
when I get up to the part where you have to type 'fastboot flash zip PG58IMG.zip it says this:
C:\android-sdk-windows\tools>fastboot flash zip PG58IMG.zip
sending 'zip' <432384 KB>...
OKAY [56.745s]
writing 'zip'...
(bootloader) signature checking...
FAILED (remote: 12 signature fail)
finished. total time: 130.818s
Click to expand...
Click to collapse
Hi,
I am not sure why you are trying to flash the PG58IMG
Can you not change the text file in the PG58IMG and then run the RUU from your PC.
Make sure your phone is in fastboot,then connect your USB cable,(it should say "fastboot USB" ) then,run the RUU.
malybru said:
Hi,
I am not sure why you are trying to flash the PG58IMG
Can you not change the text file in the PG58IMG and then run the RUU from your PC.
Make sure your phone is in fastboot,then connect your USB cable,(it should say "fastboot USB" ) then,run the RUU.
Click to expand...
Click to collapse
Hi yes I have changed the 'android-info.txt' file in PG58IMG but now what do I do? The PG58IMG.zip is in my android-sdk/tools folder.
BilalH said:
Hi yes I have changed the 'android-info.txt' file in PG58IMG but now what do I do? The PG58IMG.zip is in my android-sdk/tools folder.
Click to expand...
Click to collapse
Hi,
You do not need to extract the PG58IMG
Just open it,change it,and close it.
It remains zipped,and you can run the RUU.
malybru said:
Hi,
You do not need to extract the PG58IMG
Just open it,change it,and close it.
It remains zipped,and you can run the RUU.
Click to expand...
Click to collapse
Okay let me start from the top, where exactly do I find this PG58IMG.zip? Thanks.
Btw another question, is there a way for me to charge my phone because my battery says its below 30% if I try to install an RUU
Paste the output for
Code:
fastboot getvar all
Remove the IMEI number & serial number from the output.
I'll link you to the right RUU or tell you what else you can try.
For now, don't do anything else.
You cannot flash a modified RUU because you are S-ON; so changing the android-info file will not help.
kgs1992 said:
Paste the output for
Code:
fastboot getvar all
Remove the IMEI number & serial number from the output.
I'll link you to the right RUU or tell you what else you can try.
For now, don't do anything else.
You cannot flash a modified RUU because you are S-ON; so changing the android-info file will not help.
Click to expand...
Click to collapse
(bootloader) version: 0.5
(bootloader) version-bootloader: 1.27.0000
(bootloader) version-baseband: N/A
(bootloader) version-cpld: None
(bootloader) version-microp: None
(bootloader) version-main: 3.32.206.112
(bootloader) product: pyramid
(bootloader) platform: HBOOT-8260
(bootloader) modelid: PG5813001
(bootloader) cidnum: O2___001
(bootloader) battery-status: good
(bootloader) battery-voltage: 4052mV
(bootloader) partition-layout: Generic
(bootloader) security: on
(bootloader) build-mode: SHIP
(bootloader) boot-mode: FASTBOOT
(bootloader) commitno-bootloader: 617f0a98
(bootloader) hbootpreupdate: 11
(bootloader) gencheckpt: 0
all: Done!
finished. total time: 0.505s
Yeah so which RUU do I need or what do I need to do?
BilalH said:
(bootloader) version-main: 3.32.206.112
(bootloader) product: pyramid
(bootloader) modelid: PG5813001
(bootloader) cidnum: O2___001
(bootloader) security: on
Yeah so which RUU do I need or what do I need to do?
Click to expand...
Click to collapse
I don't think there is any O2 ICS RUU let alone 3.32 & you're S-ON, so can't flash a lower RUU.
But fortunately, all is not lost. Let's try this.
Please type these commands one after the other & paste the whole output for everything:
Code:
fastboot oem writecid HTC__001
fastboot reboot-bootloader
fastboot getvar cid
It's okay if any of them fail, you must execute all three commands one after the other & paste the output.
I have this HTC one S, I am not sure which network phone is it. I bought is from someone else and he had no idea about network.
Right now when i press factory reset from volume down + power button. it brought me at this screen which say clockwork Mod recovery v 5.8.1.5
I am able to select only first 2 options which are reboot system now and install zip from sdcard . When i pressed install zip from sdcard its not doing anything and bringing me back on same screen
Could you please help me installing stock rom on this phone. ?
Thanks in advance guys
AW: [Q] Trying to get HTC one S on stock rom? Please help ?
If you turn ur phone on with holding power and volume down you should be in your bootloader.
Can you tell us what stands on the top?
Locked/unlocked/relocked and which hboot version?
Sent from my HTC One S using xda premium
this is the info
Tampered
Unlocked
VLE PVT ship s-on RL
HBOOT-1.08.0000
Radi-0.16.31501S.06_3
open DSP-v23.1.0.32.0323
eMMC boot
Mar 21, 2012, 16:01:09
Just curious to know what this information means , please let me know each line if possible. Appreciate your help
AW: [Q] Trying to get HTC one S on stock rom? Please help ?
Tampered: no stock recovery
Unlocked: your bootloader is looked
VLE: Ville: HTC One S
S-ON: security on
Radio: your radio Version
You have to lock your bootloader.
Download the all in one toolkit which you can find in the development section. There are all necessary files.
Be sure you have installed the HTC sync driver.
1. Connect your mobile To your pc when your are in the screen where you can see hboot version etc.
2. There should be "hboot USB" in blue.
3. Navigate to hboot and press power.
4. It should change to "fastboot USB" in red.
5. Then open the all in one toolkit on your PC.
6. Open the folder where ADB and fastboot exe are located.
7. Press shift and right click somewhere in the folder and open the command line.
8. Then type in "fastboot oem lock"
9. If you take a look to your phone you should see that the "unlock" changed To "relocked"
That was the first step.
10. Go To the development section in this forum and look for the wwe europe ville ics ruu 2.31 or sth like that.
11. Download the file
12. Doubleklick the file
13. Follow the instructions
14. Let the ruu install everything
15. If everything works fine you should be on official ICS 4.0.4 with Sense 4.1 now
Good luck!
I hope I wrote an easy understandable instruction.
If u experience any problems feel free to post it here.
I'm sure I or someone else can help you.
Sent from my HTC One S using xda premium
NQNH , thanks a lot for this easy and nice explanation, its really helpful for a noob like me. I have few more questions but lets resolve this issue first. Okay I tried all steps you mentioned and it worked like a charm. just got stuck at final step. Please help.
In CMD i got this
'C:\Users\Owner\Desktop\HTC' is not recognized as an internal or external comman
d,
operable program or batch file.
C:\Users\Owner\Desktop\HTC custom rom procedure\One_S_All-In-One_Kit\data>fastbo
ot oem lock
...
(bootloader) Lock successfully...
(bootloader) TZ_HTC_SVC_DISABLE ret = 534642032 (0x1FDDFD70)
FAILED (status read failed (Too many links))
finished. total time: 0.941s
C:\Users\Owner\Desktop\HTC custom rom procedure\One_S_All-In-One_Kit\data>
This is the error message when i tried step 8, but when i checked the screen it shows relocked now , seems like it worked okay.
i tried this file
http://forum.xda-developers.com/showthread.php?t=1941402
Everytime i runs this RUU application file , after passing thru all steps it says ROM utility stopped working, Seems like i am almost done but just stuck at last point.
Hello NQNH, i tried it one more time and finally passed thru that screen. it started ROM update utility but got back with this error msg
Error (131) customer ID error
The ROM update utility cannot update your android phone
please get the correct ROM update utility and try again
I am using RUU : 1.0.6.2012
please let me know if i can use any other utility
AW: [Q] Trying to get HTC one S on stock rom? Please help ?
What do you get when you type in
fastboot getvar cid
?
Try this RUU
http://www.androidfiles.org/ruu/sec...02.31_10.09a.50.04L_release_275655_signed.exe
Sent from my HTC One S using xda premium
I tried RUU which you suggested , Thanks NQNH but sorry this time it came back with error (130) , model ID error.
fastboot getvar cid : BM___001
AW: [Q] Trying to get HTC one S on stock rom? Please help ?
Seems that you have a branded phone. (Bell Mobile Canada?)
This ruu should run fine:
http://www.androidfiles.org/ruu/sec...02.04_10.08g.50.04L_release_280275_signed.exe
Sent from my HTC One S using xda premium
Thanks Thanks Thanks Thanks a lotttttttttt, I don't know if pressing thanks button is good enough to appreciate your help. I learnt a lot from this session. If you don't mind , just for curiosity can i ask you few more questions,
Tampered (Does it mean somebody tried to install custom rom on it or something else ? )
Unlocked
VLE PVT ship s-on RL ( does S-on means this phone is unlocked or some thing else ? )
HBOOT-1.08.0000 ( is it same like version number in iphone , is it baseband version number, where i can find this number in phone settings ? )
Radi-0.16.31501S.06_3
open DSP-v23.1.0.32.0323 ( don't know what it means , please explain )
eMMC boot ( don't know what it means , please explain )
Mar 21, 2012, 16:01:09 ( is it manufacturing date or date when it was tempered )
Thanks again for your help ..
bindudhindsa said:
Thanks Thanks Thanks Thanks a lotttttttttt, I don't know if pressing thanks button is good enough to appreciate your help. I learnt a lot from this session. If you don't mind , just for curiosity can i ask you few more questions,
Tampered (Does it mean somebody tried to install custom rom on it or something else ? )
Unlocked
VLE PVT ship s-on RL ( does S-on means this phone is unlocked or some thing else ? )
HBOOT-1.08.0000 ( is it same like version number in iphone , is it baseband version number, where i can find this number in phone settings ? )
Radi-0.16.31501S.06_3
open DSP-v23.1.0.32.0323 ( don't know what it means , please explain )
eMMC boot ( don't know what it means , please explain )
Mar 21, 2012, 16:01:09 ( is it manufacturing date or date when it was tempered )
Thanks again for your help ..
Click to expand...
Click to collapse
glad to hear that I helped you.
Tampered means that someone already changed something on the phone (unlocked/relocked/custom recovery)
A comparison should be.. if you bought a new pc and if you open the case you have to break the seal. The "Tampered" say that you had break this seal on the phone (e.g. by unlocking the bootloader)
S-ON means that the security flags are on. Its a system protection so nobody can manipulate system data.
S-ON + locked bootloader -> you can do nothing, no root, no custom things
S-ON + unlocked bootloader -> you can flash custom recovery, root, custom rom (you can see an unlocked bootloader as a compromise between S-ON and S-OFF
S-OFF -> you can do everything what you want, change bootloaderGUI, bootanimations, splashscreens.
Unlocked means that you bootloader is unlocked. If its locked you cant install custom recovery, root and custom firmware. It has to be locked when you install a RUU.
You cant find your HBOOT version in your phone settings because its the version of the bootloader.
the bootloader is independed from the rom you are on. Its like the BIOS from your PC and your ROM is Win7 where you either cant find the bios version.
Radio is the module which is responsible for mobile data etc.
no/wrong/corrupt radio = no network/no signal
openDSP .. i don't know
eMMC boot, I guess that this is the partition where the bootloader is located.. but I'm not sure.
Mar 21, 2012, 16:01:09 is the date when .. difficult to explain .. when the development of the RUU was finished?
if I wrote something wrong please correct me.
Thanks a lot for this very helpful information. Appreciate your help. Kind of person like you are the reason these forums are running successfully and helping novice people like me. Thanks again.
AW: [Q] Trying to get HTC one S on stock rom? Please help ?
Thanks for your words
Sent from my HTC One S using xda premium
Hello.
I'm having same problem with getting back on stock firmware...
After trying to flash into CM10, i got stock in CM boot logo.
So trying to get back to original using RUU.
But it just looks like I can not get right one...
I did everything like in posts above, and when I enter "fastboot getvar cid" I got "HTC_Y13"
Any idea which RUU is correct for that?
I'm still trying, so maybe it will be fools luck... Or maybe someone can put me on point?
auronn said:
Hello.
I'm having same problem with getting back on stock firmware...
After trying to flash into CM10, i got stock in CM boot logo.
So trying to get back to original using RUU.
But it just looks like I can not get right one...
I did everything like in posts above, and when I enter "fastboot getvar cid" I got "HTC_Y13"
Any idea which RUU is correct for that?
I'm still trying, so maybe it will be fools luck... Or maybe someone can put me on point?
Click to expand...
Click to collapse
your cid is a unbranded eu cid.
try any unbranded eu ruu (3.16 or earlier)
Hello everyone,
So, 2 days in front of PC, reading forums and trying. No luck... So try to post it here.
I want to flash to CM10.
Bootloader is unlocked.
Recovery is installed (TWRP S4)
Root is done.
Security S-ON.
When I try to install CM10, everything went fine, but when It have to reboot it just stuck in CM booting logo loop...
And since you can't remove memory card on HTC One S, I think I have no other option how to reinstall stock firmware. And my problems starts...
I relocked bootloader.
Download already like five different RUU's...
The problem is, I can not locate my version, it's blank...
(bootloader) version: 0.5
(bootloader) version-bootloader: 2.15.0000
(bootloader) version-baseband: 1.11.50.05.28
(bootloader) version-cpld: None
(bootloader) version-microp: None
(bootloader) version-main:
(bootloader) version-misc: PVT SHIP S-ON
(bootloader) serialno: HT23NW410019
(bootloader) imei: 359901040772549
(bootloader) product: vle
(bootloader) platform: HBOOT-8960
(bootloader) modelid: PJ4010000
(bootloader) cidnum: HTC__Y13
(bootloader) battery-status: good
(bootloader) battery-voltage: 4124mV
(bootloader) partition-layout: Generic
(bootloader) security: on
(bootloader) build-mode: SHIP
(bootloader) boot-mode: FASTBOOT
(bootloader) commitno-bootloader: dirty-64bedd38
(bootloader) hbootpreupdate: 11
(bootloader) gencheckpt: 0
all: Done!
So everytime I start RUU, in the screen Current information about your Android phone" "Image version" is blank and the one with "Verify that you want to update the ROM version" "From Image Version" is blank...
When I push "Next" it goes "Checking", then "Rebooting Bootloader", "Erasing User Data" and "Sending".
When it comes to "Updating Signature" I'm getting error code...
Phone is bought in Norway, and by checking cid: HTC_Y13, I can see that it's HTC-Nor. So which one of RUU's I have to use?
I also tried to flash zip RUU, using One_S_All-In-One_Kit_v3.5 with same no luck...
Really don't know what to do... Any help would be appreciated...
Thank you in advance!
real187 said:
your cid is a unbranded eu cid.
try any unbranded eu ruu (3.16 or earlier)
Click to expand...
Click to collapse
Thank you, I'm downloading and will try this now:
RUU_Ville_U_JB_45_S_HTC_Europe_3.16.401.8_Radio_1.11.50.05.28_10.27.50.08L_release_301814_signed_2_4.exe
Already tried those:
RUU_Ville_U_ICS_40_S_HTC_Europe_2.31.401.5_Radio_1.06es.50.02.31_10.09a.50.04L_release_275655_signed.exe
RUU_VILLEC2_U_ICS_40_HTC_Europe_1.11.401.110_Radio_16.12.20.02U_16.05.20.16_M2_release_263510_signed.exe
RUU_VILLEC2_U_ICS_40_HTC_Europe_1.11.401.109_Radio_16.12.20.02U_16.05.20.16_M2_release_263131_signed.exe
RUU_VILLEPLUS_U_JB_45_HTC_Generic_1.14.999.50_Radio_1.10r.50.05.19_10.22a.50.08L_release_294323_signed.exe
And also:
OTA_Ville_U_JB_45_S_HTC_Europe_3.16.401.8_1.11.50.05.28_10.27.50.08L_release_301852xf01hejl416oev96.zip
using One_S_All-In-One_Kit_v3.5 with no luck...
Does any body can tell me the difference between Ville, VilleC2 and VillePlus?
real187 said:
your cid is a unbranded eu cid.
try any unbranded eu ruu (3.16 or earlier)
Click to expand...
Click to collapse
Thank you a lot!!!
This one worked:
RUU_Ville_U_JB_45_S_HTC_Europe_3.16.401.8_Radio_1. 11.50.05.28_10.27.50.08L_release_301814_signed_2_4 .exe
auronn said:
Hello everyone,
So, 2 days in front of PC, reading forums and trying. No luck... So try to post it here.
I want to flash to CM10.
Bootloader is unlocked.
Recovery is installed (TWRP S4)
Root is done.
Security S-ON.
When I try to install CM10, everything went fine, but when It have to reboot it just stuck in CM booting logo loop...
And since you can't remove memory card on HTC One S, I think I have no other option how to reinstall stock firmware. And my problems starts...
I relocked bootloader.
Download already like five different RUU's...
The problem is, I can not locate my version, it's blank...
(bootloader) version: 0.5
(bootloader) version-bootloader: 2.15.0000
(bootloader) version-baseband: 1.11.50.05.28
(bootloader) version-cpld: None
(bootloader) version-microp: None
(bootloader) version-main:
(bootloader) version-misc: PVT SHIP S-ON
(bootloader) serialno: HT23.......
(bootloader) imei: 3599...............
(bootloader) product: vle
(bootloader) platform: HBOOT-8960
(bootloader) modelid: PJ4010000
(bootloader) cidnum: HTC__Y13
(bootloader) battery-status: good
(bootloader) battery-voltage: 4124mV
(bootloader) partition-layout: Generic
(bootloader) security: on
(bootloader) build-mode: SHIP
(bootloader) boot-mode: FASTBOOT
(bootloader) commitno-bootloader: dirty-64bedd38
(bootloader) hbootpreupdate: 11
(bootloader) gencheckpt: 0
all: Done!
So everytime I start RUU, in the screen Current information about your Android phone" "Image version" is blank and the one with "Verify that you want to update the ROM version" "From Image Version" is blank...
When I push "Next" it goes "Checking", then "Rebooting Bootloader", "Erasing User Data" and "Sending".
When it comes to "Updating Signature" I'm getting error code...
Phone is bought in Norway, and by checking cid: HTC_Y13, I can see that it's HTC-Nor. So which one of RUU's I have to use?
I also tried to flash zip RUU, using One_S_All-In-One_Kit_v3.5 with same no luck...
Really don't know what to do... Any help would be appreciated...
Thank you in advance!
Thank you, I'm downloading and will try this now:
RUU_Ville_U_JB_45_S_HTC_Europe_3.16.401.8_Radio_1.11.50.05.28_10.27.50.08L_release_301814_signed_2_4.exe
Already tried those:
RUU_Ville_U_ICS_40_S_HTC_Europe_2.31.401.5_Radio_1.06es.50.02.31_10.09a.50.04L_release_275655_signed.exe
RUU_VILLEC2_U_ICS_40_HTC_Europe_1.11.401.110_Radio_16.12.20.02U_16.05.20.16_M2_release_263510_signed.exe
RUU_VILLEC2_U_ICS_40_HTC_Europe_1.11.401.109_Radio_16.12.20.02U_16.05.20.16_M2_release_263131_signed.exe
RUU_VILLEPLUS_U_JB_45_HTC_Generic_1.14.999.50_Radio_1.10r.50.05.19_10.22a.50.08L_release_294323_signed.exe
And also:
OTA_Ville_U_JB_45_S_HTC_Europe_3.16.401.8_1.11.50.05.28_10.27.50.08L_release_301852xf01hejl416oev96.zip
using One_S_All-In-One_Kit_v3.5 with no luck...
Does any body can tell me the difference between Ville, VilleC2 and VillePlus?
Click to expand...
Click to collapse
Firstly, I would recommend removing part of your IMEI and Serial Numbers from your post, it could be used in bad ways by other people.
Ville is the HTC One S with a Snapdragon S4 chipset, clocked at 1.5GHz (dual core) otherwise known as z520e. (You have this phone)
VilleC2 is what became of the HTC One S when HTC ran out of Snapdragon S4 chipsets in many parts of the world due to a shortage. It has a Snapdragon S3, clocked at 1.7GHz (dual core) otherwise known as z560e.
VillePlus is a Special Edition version of the HTC One S, only available in Taiwan. It has the same processor as the Ville, except comes in a white body instead of the normal grey or black options and has 64GBs of internal storage. The other two have 16GBs internal storage. This phone is quite rare.
You should try RUUs only that say ville, and not VillePlus or VilleC2. These won't work and may even irreversibly damage your phone.
OTAs only work when you already have a previous firmware version. Let's say you were on ICS, a Jelly Bean FOTA is released (firmware over the air) and installs ("flashes") on top of your existing ICS installation, keeping your apps and data.
RUUs wipe all data and wipe everything on the phone when installing through a USB connection.
Could you specify what error code you get on the RUUs?
----
The reason why CM10 didn't boot is because you didn't flash the boot.img.
You need to extract the boot.img from the CM10 zip and put that into your "working folder" (the folder with adb and fastboot files in it)
Open up a command prompt / terminal in that folder and type
fastboot flash boot boot.img
when you are in FASTBOOT USB mode in the bootloader.
Go to Fastboot. Plug in your USB with the phone. Now, ctrl and r --> type cmd --> cd to C:/where your adb is --> fastboot read cid
Then type the 8 digit string that you get. It would help us determine your network provider.
I have a HTC One S cell phone that stopped working after I did a software update from the settings menu. The phone has no service (not able to connect to the network). My service provider is Wind mobile. They tried a "hard reset" or factory data reset this did not solve the problem. Then I had a technician replace the firmware and downgrade to an earlier version of software. This got the phone to work. I was able to make one call. However I was unable to pickup wifi. I tried to turn on wifi in the setting menu and then the phone stopped working again. I have tried talking to HTC customer service but they have not been able (or willing) to help.
HTC One S
model Z520m, Android
HBOOT- 2.15.0000
RADIO - 1.11.50.05.28
Open DSP - v31.1.0.45.0815
eMMC - boot
device: ville
build id: JR003C
SDK version: 16
Release: 4.1.1
Incremental version: 133955.7
Does anyone know how to fix this phone?
I suspect that either the firmware installed incorrectly or is the wrong version for the phone.
Does anyone know where to get the correct version of the firmware?
Thank You,
Greg
dwa789 said:
I have a HTC One S cell phone that stopped working after I did a software update from the settings menu. The phone has no service (not able to connect to the network). My service provider is Wind mobile. They tried a "hard reset" or factory data reset this did not solve the problem. Then I had a technician replace the firmware and downgrade to an earlier version of software. This got the phone to work. I was able to make one call. However I was unable to pickup wifi. I tried to turn on wifi in the setting menu and then the phone stopped working again. I have tried talking to HTC customer service but they have not been able (or willing) to help.
HTC One S
model Z520m, Android
HBOOT- 2.15.0000
RADIO - 1.11.50.05.28
Open DSP - v31.1.0.45.0815
eMMC - boot
device: ville
build id: JR003C
SDK version: 16
Release: 4.1.1
Incremental version: 133955.7
Does anyone know how to fix this phone?
I suspect that either the firmware installed incorrectly or is the wrong version for the phone.
Does anyone know where to get the correct version of the firmware?
Thank You,
Greg
Click to expand...
Click to collapse
Connect phone in fastboot mode to your computer, open CMD commandline and type "fastboot getvat all". You will get a log.Delete your IMEI / serial from the log and post it here (The LOG not the IMEI...)
LS.xD said:
Connect phone in fastboot mode to your computer, open CMD commandline and type "fastboot getvat all". You will get a log.Delete your IMEI / serial from the log and post it here (The LOG not the IMEI...)
Click to expand...
Click to collapse
bootloader) version: 0.5
(bootloader) version-bootloader: 2.15.0000
(bootloader) version-baseband: 1.11.50.05.28
(bootloader) version-cpld: None
(bootloader) version-microp: None
(bootloader) version-main: 3.16.1500.7
(bootloader) version-misc: PVT SHIP S-ON
(bootloader) serialno:
(bootloader) imei:
(bootloader) product: vle
(bootloader) platform: HBOOT-8960
(bootloader) modelid: PJ4011000
(bootloader) cidnum: GLOBA001
(bootloader) battery-status: good
(bootloader) battery-voltage: 4106mV
(bootloader) partition-layout: Generic
(bootloader) security: on
(bootloader) build-mode: SHIP
(bootloader) boot-mode: FASTBOOT
(bootloader) commitno-bootloader: dirty-64bedd38
(bootloader) hbootpreupdate: 11
(bootloader) gencheckpt: 0
I'll get the link for the matching RUU file for you
There is no matching RUU OTA update is avaiable. Are you familiar with using fastboot commands? DOWNLOAD the OTA. Extract the included firmware.zip and flash it via fastboot. If it works --> good. If not you'll have to change your CID to install a RUU for unbraded versions of the phone.
Thanks for locating the OTA update. I am not familiar with using fastboot commands. Can you link me to a guide or post that explains the procedure.
Thank You,
Greg
dwa789 said:
Thanks for locating the OTA update. I am not familiar with using fastboot commands. Can you link me to a guide or post that explains the procedure.
Thank You,
Greg
Click to expand...
Click to collapse
Download ADB/fastboot, uninstall HTC Sync. Connect your phone in fastboot mode, open CMD commandline an type:
"fastboot oem rebootRUU"
"fastboot flash zip firmware.zip"
"fastboot flash zip firmware.zip" (AGAIN!)
"fastboot reboot-bootloader"
Then reboot the phone to check if android is running
I followed the steps you provided and the firmware loaded fine and Android is also running. However the phone is still not working properly. The phone was randomly switching between "no service" for several minutes and then to WIND away (roaming) and then to 4G with varying signal strength. I was able to make a brief call while the phone was in 4G mode. Now the phone seems to be stuck with "no service" again. Any ideas as to what could be the problem?
Thanks
dwa789 said:
I followed the steps you provided and the firmware loaded fine and Android is also running. However the phone is still not working properly. The phone was randomly switching between "no service" for several minutes and then to WIND away (roaming) and then to 4G with varying signal strength. I was able to make a brief call while the phone was in 4G mode. Now the phone seems to be stuck with "no service" again. Any ideas as to what could be the problem?
Thanks
Click to expand...
Click to collapse
Yes You will need to install a FULL system e.g. RUU. The firmware contains all basic partitions of your phone BUT not System, data ... If you tried instaling a OTA update and it failed --> You need a CLEAN installation.
LS.xD said:
Yes You will need to install a FULL system e.g. RUU. The firmware contains all basic partitions of your phone BUT not System, data ... If you tried instaling a OTA update and it failed --> You need a CLEAN installation.
Click to expand...
Click to collapse
How do I preform a CLEAN (Full system) installation?
dwa789 said:
How do I preform a CLEAN (Full system) installation?
Click to expand...
Click to collapse
You can't. As least you can't do it by the ormal way, as there is NO stock RUU package available for your phone. You can Unlock the bootloader, set it S-OFF, then you're able to install unbranded or custom software.
LS.xD said:
You can't. As least you can't do it by the ormal way, as there is NO stock RUU package available for your phone. You can Unlock the bootloader, set it S-OFF, then you're able to install unbranded or custom software.
Click to expand...
Click to collapse
I hate to ask any more questions because you have been so helpful in answering all my questions but I would really like to get my phone working again.
How do I go about Unlocking the bootloader, setting it to S-OFF and then installing unbranded software? Also where do I get unbranded software that will work with my phone?
dwa789 said:
I hate to ask any more questions because you have been so helpful in answering all my questions but I would really like to get my phone working again.
How do I go about Unlocking the bootloader, setting it to S-OFF and then installing unbranded software? Also where do I get unbranded software that will work with my phone?
Click to expand...
Click to collapse
How about you get Teamviever and i'll set up the phone for you?
LS.xD said:
How about you get Teamviever and i'll set up the phone for you?
Click to expand...
Click to collapse
Ok, I installed Teamviewer on my computer.
dwa789 said:
Ok, I installed Teamviewer on my computer.
Click to expand...
Click to collapse
PM me ID+pass when you're ready
My HTC One SV (LTE europe version ) stuck while booting, it displays white logo screen only,
now i unlocked bootloader and tried to flash rom, but failed,
How i can flash a custom rom or original oerating systedm in my phone,
please help me.
anpayy said:
My HTC One SV (LTE europe version ) stuck while booting, it displays white logo screen only,
now i unlocked bootloader and tried to flash rom, but failed,
How i can flash a custom rom or original oerating systedm in my phone,
please help me.
Click to expand...
Click to collapse
Can you get into the bootloader? If you can, you can flash TWRP recovery via fastboot and flash a custom Rom with the recovery.
Yes
thearif said:
Can you get into the bootloader? If you can, you can flash TWRP recovery via fastboot and flash a custom Rom with the recovery.
Click to expand...
Click to collapse
i can get into bootloder, but where can i get TWRP recovery and custom rom file ?
anpayy said:
i can get into bootloder, but where can i get TWRP recovery and custom rom file ?
Click to expand...
Click to collapse
Go to http://forum.xda-developers.com/showthread.php?t=2292432 . Read through and find the recovery there. It is pretty well explained there. I am on my mobile so I am not sure of the link will take you to the first page. It is on the first page. Make sure you get the correct recovery for your phone model.
Original rom
Where i can get original ROM for HTC ONE SV LTE k2ul_4.2.2_3.11.401.1 ???
anpayy said:
Where i can get original ROM for HTC ONE SV LTE k2ul_4.2.2_3.11.401.1 ???
Click to expand...
Click to collapse
That I do not know, but if my memory serves me right, there was a thread either in android development or general sections with the latest OTAs. You might wanna search for that...
anpayy said:
Where i can get original ROM for HTC ONE SV LTE k2ul_4.2.2_3.11.401.1 ???
Click to expand...
Click to collapse
You've already got the link to my index thread, but it seems you are to lazy to have a look at it. You even only need to watch for the software number and you will easily find what you are searching for.
Os intallation failed
i tried to install OTA update through TWRP recovery , but it failed
You can't flash this in recovery. Use TWRP recovery and flash the rom (not the Ota). Links are in my index thread.
Installed rom
Sucessfully instaled Viper SV rom,
but still phone did not booting,
Did you also flash boot.img of the rom in fastboot?
no
I missed to boot boot.img,
Now phone is working perfectly...........
Thanks all........specially old.splatterhand & thearif
Nice
anpayy said:
I missed to boot boot.img,
Now phone is working perfectly...........
Thanks all........specially old.splatterhand & thearif
Click to expand...
Click to collapse
Good to hear that...
Hi all,
I'm new in this forum so I post there.
My problems starts after try to updete htc one sv k2_ul. After update I get red triangle and then my phone freezed on white screen with logo.
Try to do factory reset from bootloader, but nothing happen. After few days looking information I unlock bootloader and try flash new boot, but after that I get Tampered. I found if I must s-off, but how I can get it? My pc found phone only on fastboot mode. Any ideas?
miegas said:
Hi all,
I'm new in this forum so I post there.
My problems starts after try to updete htc one sv k2_ul. After update I get red triangle and then my phone freezed on white screen with logo.
Try to do factory reset from bootloader, but nothing happen. After few days looking information I unlock bootloader and try flash new boot, but after that I get Tampered. I found if I must s-off, but how I can get it? My pc found phone only on fastboot mode. Any ideas?
Click to expand...
Click to collapse
You can't get S-off, without working OS.
You don't have an OS anymore on your phone?
Are you running a custom recovery like TWRP?
Run this fastboot cmd and copy the output here (remove your imei & serial number):
Code:
fastboot getvar all
old.splatterhand said:
You can't get S-off, without working OS.
You don't have an OS anymore on your phone?
Are you running a custom recovery like TWRP?
Run this fastboot cmd and copy the output here (remove your imei & serial number):
Code:
fastboot getvar all
Click to expand...
Click to collapse
My os just stop working.
I don't try TWRP, today will look more about that.
(bootloader) version: 0.5
(bootloader) version-bootloader: 2.00.0000
(bootloader) version-baseband: 1.15.40a.00.04
(bootloader) version-cpld: None
(bootloader) version-microp: None
(bootloader) version-main: 2.14.401.6
(bootloader) version-misc: PVT SHIP S-ON
(bootloader) serialno:
(bootloader) imei:
(bootloader) product: k2_ul
(bootloader) platform: HBOOT-8930
(bootloader) modelid: PL8010000
(bootloader) cidnum: HTC__001
(bootloader) battery-status: good
(bootloader) battery-voltage: 4143mV
(bootloader) partition-layout: Generic
(bootloader) security: on
(bootloader) build-mode: SHIP
(bootloader) boot-mode: FASTBOOT
getvar:all FAILED (status read failed (Too many links))
finished. total time: 0.075s
edit
I flashed TWRP and I make restore, but phone won't start anyway. Maybe need to flash new os?
Flash the stock rom in TWRP, and don't forget to flash boot.img of the rom in fastboot.
Links are in my index thread.
Make a backup in recovery (just in case) and a wipe (advanced -> everything except int & ext sdcard) before.
old.splatterhand said:
Flash the stock rom in TWRP, and don't forget to flash boot.img of the rom in fastboot.
Links are in my index thread.
Make a backup in recovery (just in case) and a wipe (advanced -> everything except int & ext sdcard) before.
Click to expand...
Click to collapse
Something I make wrong. I flashed TWRP, then installed ViperSV, phone restarted and booted TWRP. Then I found boot.img in yours index thead.
Then in fastboot flashed new boot, but phone still booting in TWRP. What I make wrong?
You need to flash the boot.img thats inside the ViperSV.zip, not any from my index thread.
Hi all! I have a bricked HTC Sensation 4G (T-Mobile) that I am trying to fix.
I need help with RUUing the HTC Sensation 4G. (Z710e)
I believe I have tried everything, all without luck, please help, TIA.
Heres the problem with the phone- It appears to be stuck in a bootloop, boots up to the white HTC screen, makes the HTC startup chime with Quietly Brilliant written under it, and then immediately reboots, and continuously does this over and over again.
Heres what I know about the phone
The Bootloader is Locked
The Phone is S-ON
The CID of the phone is HTC__621
Here's what I've tried
I have tried RUUing the phone with RUU_PYRAMID_ICS_TMOUS_3.32.531.14_Radio_11.69A.3504.00U_11.23.3504.07_M2_release_256085_signed.exe
since it is a T-Mobile HTC Sensation 4G. However I keep getting Error 130: Model ID error.
I also tried RUUing the phone manually using CMD, following the guide however this failed aswell, I kept getting "remote: 12 signature verify fail" at the end.
I also tried renaming extracting the rom.zip from the RUU, renaming that to PG58IMG.zip, placing that on my sd card and booting the phone into bootloader. However when I tried this it said checking PG158.img, but nothing happened, it just continued to boot up to the bootloader.
At this point I realized maybe that this RUU didn't match my CID, which was why it was failing. So I tried opening the ROM.zip file however it said it was corrupt in windows explorer. I then tried redownloading the RUU but it still kept saying ROM.zip was corrupt. I then opening ROM.zip with winrar and it opened up! I then opened android-info.text and saw that the cidnum for the RUU was T-MOB0101. I tried changing this to my CID (HTC__621) and then saving as instructed in this guide, however when I pressed on YES to update the files in the archive, winrar gives an error and says that the archive is corrupt, and does not update android-info.text.
I am not sure what else to try at this point, and I am stumped as to why none of the following methods I've tried worked. Is there something I am doing wrong? Is there anything I'm missing? Any help would be very gladly appreciated, as I am out of ideas.
Also worth noting, I've attached 2 pictures below as attachements to this post, (since I am new to xdadevelopers I cannot post direct links to images), one of the bootloader of the phone, including information such as my hboot version, radio version, etc. in case its needed.
I've also attached a picture below of what happens when I put the phone into HTC stock android recovery and press Factory Data Wipe/Reset. I get a bunch of errors, I'm not sure if this is related to anything but it doesn't look normal, so I attached a picture of it below.
Thanks in advance!
sebzter said:
Hi all! I have a bricked HTC Sensation 4G (T-Mobile) that I am trying to fix.
I need help with RUUing the HTC Sensation 4G. (Z710e)
I believe I have tried everything, all without luck, please help, TIA.
Heres the problem with the phone- It appears to be stuck in a bootloop, boots up to the white HTC screen, makes the HTC startup chime with Quietly Brilliant written under it, and then immediately reboots, and continuously does this over and over again.
Heres what I know about the phone
The Bootloader is Locked
The Phone is S-ON
The CID of the phone is HTC__621
Here's what I've tried
I have tried RUUing the phone with RUU_PYRAMID_ICS_TMOUS_3.32.531.14_Radio_11.69A.3504.00U_11.23.3504.07_M2_release_256085_signed.exe
since it is a T-Mobile HTC Sensation 4G. However I keep getting Error 130: Model ID error.
I also tried RUUing the phone manually using CMD, following the guide however this failed aswell, I kept getting "remote: 12 signature verify fail" at the end.
I also tried renaming extracting the rom.zip from the RUU, renaming that to PG58IMG.zip, placing that on my sd card and booting the phone into bootloader. However when I tried this it said checking PG158.img, but nothing happened, it just continued to boot up to the bootloader.
At this point I realized maybe that this RUU didn't match my CID, which was why it was failing. So I tried opening the ROM.zip file however it said it was corrupt in windows explorer. I then tried redownloading the RUU but it still kept saying ROM.zip was corrupt. I then opening ROM.zip with winrar and it opened up! I then opened android-info.text and saw that the cidnum for the RUU was T-MOB0101. I tried changing this to my CID (HTC__621) and then saving as instructed in this guide, however when I pressed on YES to update the files in the archive, winrar gives an error and says that the archive is corrupt, and does not update android-info.text.
I am not sure what else to try at this point, and I am stumped as to why none of the following methods I've tried worked. Is there something I am doing wrong? Is there anything I'm missing? Any help would be very gladly appreciated, as I am out of ideas.
Also worth noting, I've attached 2 pictures below as attachements to this post, (since I am new to xdadevelopers I cannot post direct links to images), one of the bootloader of the phone, including information such as my hboot version, radio version, etc. in case its needed.
I've also attached a picture below of what happens when I put the phone into HTC stock android recovery and press Factory Data Wipe/Reset. I get a bunch of errors, I'm not sure if this is related to anything but it doesn't look normal, so I attached a picture of it below.
Thanks in advance!
Click to expand...
Click to collapse
You can access bootloader so no problems here. Unlock bootloader through htcdev. In fastboot mode flash latest 4ext recovery, enable smartflash in settings, then flash a custom rom. You can also try Android Revolution HD rom if you prefer a stock look.
matekaneve said:
You can access bootloader so no problems here. Unlock bootloader through htcdev. In fastboot mode flash latest 4ext recovery, enable smartflash in settings, then flash a custom rom. You can also try Android Revolution HD rom if you prefer a stock look.
Click to expand...
Click to collapse
Thanks for the info! However I just tried unlocking the bootloader through htcdev but I keep getting an error at the end "Unlock token check failed". You can see this in the picture I attached below of the command prompt window. Any ideas? I tried resubmitting my unlock token on htcdev to make sure I didn't leave any extra spaces or anything but still got the same result. Thanks
sebzter said:
Thanks for the info! However I just tried unlocking the bootloader through htcdev but I keep getting an error at the end "Unlock token check failed". You can see this in the picture I attached below of the command prompt window. Any ideas? I tried resubmitting my unlock token on htcdev to make sure I didn't leave any extra spaces or anything but still got the same result. Thanks
Click to expand...
Click to collapse
Strange... Make sure you copy and paste right from the beginning to the end. You can also try to move your adb/fastboot folder somewhere else for example to the desktop and try resubmitting the token from there. (Might sound stupid but works sometimes). If not, you need to find the right RUU for your device and RUU it, then follow this guide for s-off: http://forum.xda-developers.com/showthread.php?p=26280760 there are some devices htcdev unlock doesn't work unfortunately... Otherwise I have no other idea, sorry. Somebody might be able to help.
matekaneve said:
Strange... Make sure you copy and paste right from the beginning to the end. You can also try to move your adb/fastboot folder somewhere else for example to the desktop and try resubmitting the token from there. (Might sound stupid but works sometimes). If not, you need to find the right RUU for your device and RUU it, then follow this guide for s-off: http://forum.xda-developers.com/showthread.php?p=26280760 there are some devices htcdev unlock doesn't work unfortunately... Otherwise I have no other idea, sorry. Somebody might be able to help.
Click to expand...
Click to collapse
Thanks again for your response, I just did it again this time with my fastboot folder on the desktop, however I still got the same error. How would I find the right RUU for my device? It is an american HTC Sensation 4G from T-Mobile with its CID: HTC__621. I haven't been able to find another RUU for it other than the one I used as previously mentioned in my original post. If anyone has the link to the right RUU I could use for this device, it would be really helpful. Thanks again.
sebzter said:
Thanks again for your response, I just did it again this time with my fastboot folder on the desktop, however I still got the same error. How would I find the right RUU for my device? It is an american HTC Sensation 4G from T-Mobile with its CID: HTC__621. I haven't been able to find another RUU for it other than the one I used as previously mentioned in my original post. If anyone has the link to the right RUU I could use for this device, it would be really helpful. Thanks again.
Click to expand...
Click to collapse
Could you write here the info you get for the command "fastboot getvar all"
matekaneve said:
Could you write here the info you get for the command "fastboot getvar all"
Click to expand...
Click to collapse
Yes, here it is
Code:
(bootloader) version: 0.5
(bootloader) version-bootloader: 1.27.0000
(bootloader) version-baseband: 11.24A.3504.31_M
(bootloader) version-cpld: None
(bootloader) version-microp: None
(bootloader) version-main: 3.33.709.6
(bootloader) serialno:
(bootloader) imei:
(bootloader) product: pyramid
(bootloader) platform: HBOOT-8260
(bootloader) modelid: PG5813000
(bootloader) cidnum: HTC__621
(bootloader) battery-status: good
(bootloader) battery-voltage: 3991mV
(bootloader) partition-layout: Generic
(bootloader) security: on
(bootloader) build-mode: SHIP
(bootloader) boot-mode: FASTBOOT
(bootloader) commitno-bootloader: 617f0a98
(bootloader) hbootpreupdate: 11
(bootloader) gencheckpt: 0
all: Done!
finished. total time: 0.562s
sebzter said:
Yes, here it is
Code:
(bootloader) version: 0.5
(bootloader) version-bootloader: 1.27.0000
(bootloader) version-baseband: 11.24A.3504.31_M
(bootloader) version-cpld: None
(bootloader) version-microp: None
(bootloader) version-main: 3.33.709.6
(bootloader) serialno:
(bootloader) imei:
(bootloader) product: pyramid
(bootloader) platform: HBOOT-8260
(bootloader) modelid: PG5813000
(bootloader) cidnum: HTC__621
(bootloader) battery-status: good
(bootloader) battery-voltage: 3991mV
(bootloader) partition-layout: Generic
(bootloader) security: on
(bootloader) build-mode: SHIP
(bootloader) boot-mode: FASTBOOT
(bootloader) commitno-bootloader: 617f0a98
(bootloader) hbootpreupdate: 11
(bootloader) gencheckpt: 0
all: Done!
finished. total time: 0.562s
Click to expand...
Click to collapse
Your firmware version (3.33.709.6) is an Asian one. Try downloading this ruu and run it: http://androidruu.com/getdownload.p...0U_11.24A.3504.31_M_release_266490_signed.exe
Edit: and delete your serial and imei number from your post!
matekaneve said:
Your firmware version (3.33.709.6) is an Asian one. Try downloading this ruu and run it: http://androidruu.com/getdownload.p...0U_11.24A.3504.31_M_release_266490_signed.exe
Edit: and delete your serial and imei number from your post!
Click to expand...
Click to collapse
Hi, thanks again for your help! The RUU completed successfully this time!!! However, unfortunately, for some reason it is still bootlooping :/
When I turn it on, it shows the HTC logo, plays the little chime with Quitely Brilliant written under HTC, makes a very silent beep noise, and reboots. It keeps on doing this again and again.
Any ideas on what to do next? Why would the phone do this?
sebzter said:
Hi, thanks again for your help! The RUU completed successfully this time!!! However, unfortunately, for some reason it is still bootlooping :/
When I turn it on, it shows the HTC logo, plays the little chime with Quitely Brilliant written under HTC, makes a very silent beep noise, and reboots. It keeps on doing this again and again.
Any ideas on what to do next? Why would the phone do this?
Click to expand...
Click to collapse
Well, I'm out of ideas now. At least the ruu worked. Try maybe the htcdev unlock again now. Get a new token and submit that. And go for the normal sensation option on htcdev site and NOT for the 4g
sebzter said:
Hi, thanks again for your help! The RUU completed successfully this time!!! However, unfortunately, for some reason it is still bootlooping :/
When I turn it on, it shows the HTC logo, plays the little chime with Quitely Brilliant written under HTC, makes a very silent beep noise, and reboots. It keeps on doing this again and again.
Any ideas on what to do next? Why would the phone do this?
Click to expand...
Click to collapse
UPDATE!! I just got the phone to sorta bootup once! It booted up to a configuring android screen (in japanese) and then it shut right off, and started rebooting again. Why is the phone constantly and randomly rebooting like this? I've heard some people said it was the battery but the battery seemed to hold a fairly long charge in bootloader mode, so I don't see why this would be the issue. Anyways I will try an htcdev unlock now and see if that works, will update soon.