Database Info

Honor 6 H60-L02 impossible to charge the phone

Hi Guys,
1. I have upgraded my phone to OTA-EMUI 4.0_H60-L02-L12_6.2.1_6.3.1 which runs properly.
2. Afterwards, I wanted to root this phone again, which doesn't work neither with multi-tool nor TRWM.
3. After reboot the phone was going into animated Honor logo, but nothing more.
4. I tried to reinstall the original firmware using adb shell and dd. Same situation
Unluckily the phone doesn't boot normally after the reboot.
5. Pressing the power button for a while lets the phone vibrate ones and appear logo but nothing else happens.
Pressing 3 buttons lets the phone come up with the honor-logo, but nothing more.
Pressing power + vol- and connected usb cable lets the phone come up with fastboot.
When the phone is in fastboot mode my computer recognizes it as "Android Phone - Android Sooner Single ADB Interface",
but ADB doesn't show any devices. Fastboot works fine and is Unlocked. Hisuite doesn`t recognize device...search drivers but
nothing happens.
6. Unbricking the phone using fastboot (flash boot, cust, recovery and system) doesn't change anything.
Flashing the stock recovery, using a sd-card with dload folder and firmware and booting the phone with any button
combination doesn't change anything (no installer, no recovery). Flashing CWM and booting the phone with any button
combination doesn't change anything (no recovery). ADB doesn't show a device at any other point of booting.
7. Now the accu from my phone is empty and I can't charge it again, neither with USB-cable plugged to Computer nor with
standard cable plugged into a switch. I need help before playing tennis with this phoe!! :crying:
Any idea or solution how to fix all my problem?

Solved Problem with bricked H60 L02, which doesn't charge
Solved the Problem with this post By panamera2011:
http://forum.xda-developers.com/honor-6/general/l02-l12-how-to-emui-4-0-to-emui-3-1-t3318231:
L02/L12 - How to go back from EMUI 4.0 to EMUI 3.1
I flashed with fastboot:
fastboot devices
fastboot flash recovery RECOVERY.img
fastboot flash boot BOOT.img
fastboot flash fastboot FASTBOOT.img
from OTA-EMUI 4.0_H60-L02-L12_6.2.1_6.3.1
Afterwards the phone began to charge again.
I copied the update.app from H60_EMUI3.1_Android5.1_6.1.1 to the folder DLOAD, inserted the SD -Card,
disconnected the USB cable from your PC, pressed 3btn till the Honor logo appears
continued to press 3btn for 8 -10 seconds and the recovery process began.
Thank a lot to panamera2011

Thanks Sam Cro!
I think your answer is underrated.
Most of my bricks on the Honor 6 (H60-L12) could be restored thanks to your help!

Huawei P9 Brick( The easiest way to unbrick)

1. First Turn off your Device (If you can't then Drain The Battery)
2. HOLD Volume Down & Connect to USB ( Now your phone will boot to fastboot )
3. DOWNLOAD ADB & Fastboot on your Computer. Link - https://mega.nz/#F!sSZDmYiA!RnMmcG88-nvqQj7UNPrPZw
4. Extract your stock firmware via Huawei UPDATE.app Extractor Software (Recovery only)
If you're on Marshmallow Before then extract Marshmallow Firmware
If you're on Nougat Before then extract Nougat Firmware
Huawei UPDATE.app Extractor Software
Link - https://mega.nz/#F!JGh2QLYD!Z1OG8HtbWt1i4XvL6WOt3Q
Now Copy Recovery AND paste into ADB & Fastboot FOLDER
Now DOWNLOAD TWRP
If you're on Marshmallow Before than DOWNLOAD From this link
https://dl.twrp.me/eva/twrp-3.1.1-0-eva.img.html
If you're on Nougat Before than DOWNLOAD From this link
https://mega.nz/#!1HoVmDoa!9ifPg7yfEKfCRfbVI04Qvsbt49PAjA3MO72RoD4EPnc
Now Copy twrp AND paste into ADB & Fastboot FOLDER & Rename twrp
5. Open ADB & Fastboot FOLDER
6. HOLD Shift Key & Right Click on empty place of this FOLDER
7. Click on OPEN COMMAND WINDOW HERE
8. Type - fastboot oem unlock (UNLOCK KEY) --- Skip this step if your BOOTLOADER is UNLOCKED
Now press Enter Key
9. Type - fastboot flash recovery Recovery.img
Now press Enter Key
10. Type - fastboot flash recovery twrp.img
Now press Enter Key
11. Now HOLD Volume Up & Power Button AND Release Volume Up Button when you see Huawei Logo & Just HOLD Vol Up
12. Now flash custom rom
If you're on Marshmallow Before than DOWNLOAD From this link
https://www.androidfilehost.com/?fid=457095661767122613
If you're on Nougat Before than DOWNLOAD From this link
https://www.androidfilehost.com/?fid=889764386195922724
13. Now DOWNLOAD Stock firmware (If you ALREADY DOWLOAD it then skip this step)
14. Extract Your Firmware Copy dload FOLDER & Paste into root Directory of your Memory CARD
15. Go to twrp - wipe - swipe to factory
16. Turn off your phone
17. HOLD Volume Up & Down also Power Button until your Device boot to DOWNLOAD MODE
Now your stock firmware will be installED
Enjoy you unbrick your Huawei P9
Hit the thanks :good: button if you Happy to My Work
Note — If you didn't to use Huawei UPDATE.app extractor Software then check this link
If you didn't now how to flash a custom rom then you should learn it before flashing

Hi,
I was on B386 before (Nougat)
Flashing RR-N-v5.8.4 gives this error:
Can't install this package on top of incompatible data. Please try another package or run a factory reset.
Updater process ended with ERROR 7
Any idea ?
Thanks !
PS : This error also prevents me to install B390, B383, B182. Only B360 can be installed from TWRP.

XavierP56 said:
Hi,
I was on B386 before (Nougat)
Flashing RR-N-v5.8.4 gives this error:
Can't install this package on top of incompatible data. Please try another package or run a factory reset.
Updater process ended with ERROR 7
Any idea ?
Thanks !
PS : This error also prevents me to install B390, B383, B182. Only B360 can be installed from TWRP.
Click to expand...
Click to collapse
Try to install Lineage 14.1

problem
my p9 i do the things as you saying but it when it goes on fastboot stack on screen your devise is booting now...wont open and at adb says waiting for devise nothing else what to do ?

To get into fastboot mode you keep the phone plugged into computer and hold power and volume down until you get to the white fastboot screen.
There is no need to wait for the battery to drain as you can just force shut down a phone using power + volume down holding.

Huawei p9 EVA-L09
Hi there, i am having an issue when flashing RECOVERY or any .IMG into my phone... It is in fastboot mode And i am getting an error when flashing img file , Error : Command Not allowed ...... YES i know what ur going to say (Enable OEM unlock)or(Enable usb debugging in setting) But the problem is that I cannot boot into OS nor recovery, I am stuck on the (Your Device is unlocked and can't be trusted (1)Press power key to continue ECT..... Is there any way Beside Enabling OEM unlock method to fix this or enabling me to gain access to flash recovery or any img file without Command not allowed error ?Ive recently Installed this rom https://forum.xda-developers.com/p9/development/rom-ncs-rom-v1-1-08-16-2016-t3440269 idk if that is part of the Issue Would be Much appreciated for the help
Forgot to mention that doing the 3 buttom method to restore using DLOAD , I get stuck on the HUAWEI logo and doesnt seem to boot into the Updating state.

Follow my guide, post #7! Leave feedback and a thanks!
https://forum.xda-developers.com/showpost.php?p=74169408

phone is booting but screen doesnt turn on
the phone is booting and dload method is working but the issue is the screen is just blank after huawei logo but is not in loop as it is not booting continuosly its blank forever

nothing helps
Hi
I came here because i tried to install miui on my P9 via trwp , somehow it wasnt mountable and after searching the internet i found the solution was to change the filetype.
Sadly i forgot that this would delete my backup, which happened and the miui still wasnt mountable.
I tried your method but after a few miliseconds of the forced update it gets an error and stops.
Or lets say i tried your method while being in trwp recovery mode because otherwise no devices are being detected by adb tool.
i tried to install a p9 stock rom but i cant even mount that one, somehow nothing works.
I seriously dont know what to do anymore.

Try this...
Try to flash downgrade firmware...
Rollback Instructions
Step 1. Download the appropriate rollback firmware
Step 2. Copy the extracted dload folder to the external storage of your phone (micro sd card).
Step 4. Disconnect the USB cable and turn your phone off.
Step 5. Now hold Volume up + Volume down + Power buttons until the installation screen appears.
Step 6. When the phone restarts after completing the installation, your firmware version should now be “B300”.
Step 7. Try to find oldest marshmallow firmware and flash it using same way...

I want to android 6.0 as twrp. How ? Pls

That is only for unlocked bootloader??

Link in Step 12 for Nougat s broken

JaayTee said:
Hi there, i am having an issue when flashing RECOVERY or any .IMG into my phone... It is in fastboot mode And i am getting an error when flashing img file , Error : Command Not allowed ...... YES i know what ur going to say (Enable OEM unlock)or(Enable usb debugging in setting) But the problem is that I cannot boot into OS nor recovery, I am stuck on the (Your Device is unlocked and can't be trusted (1)Press power key to continue ECT..... Is there any way Beside Enabling OEM unlock method to fix this or enabling me to gain access to flash recovery or any img file without Command not allowed error ?Ive recently Installed this rom https://forum.xda-developers.com/p9/development/rom-ncs-rom-v1-1-08-16-2016-t3440269 idk if that is part of the Issue Would be Much appreciated for the help
Forgot to mention that doing the 3 buttom method to restore using DLOAD , I get stuck on the HUAWEI logo and doesnt seem to boot into the Updating state.
Click to expand...
Click to collapse
Same problem plzzzzzzzzzz help!!!!

I can't access anything but "your device is booting now" screen - after this phone automaticly shuts down
pls help!!!

Trying to follow the guide but cannot even get to fastboot mode.
Trying to follow the guide but cannot even get to fastboot mode.
With phone off and pressing down-vol and power, it gets straight to:
Func NO: 11 (recovery image) Error NO: 2 (load failed!)
Am i doing something wrong? Help appreciated.
Cheers

Bricked p9
Blak Rider said:
Same problem plzzzzzzzzzz help!!!!
Click to expand...
Click to collapse
JaayTee said:
Hi there, i am having an issue when flashing RECOVERY or any .IMG into my phone... It is in fastboot mode And i am getting an error when flashing img file , Error : Command Not allowed ...... YES i know what ur going to say (Enable OEM unlock)or(Enable usb debugging in setting) But the problem is that I cannot boot into OS nor recovery, I am stuck on the (Your Device is unlocked and can't be trusted (1)Press power key to continue ECT..... Is there any way Beside Enabling OEM unlock method to fix this or enabling me to gain access to flash recovery or any img file without Command not allowed error ?Ive recently Installed this rom https://forum.xda-developers.com/p9/development/rom-ncs-rom-v1-1-08-16-2016-t3440269 idk if that is part of the Issue Would be Much appreciated for the help
Forgot to mention that doing the 3 buttom method to restore using DLOAD , I get stuck on the HUAWEI logo and doesnt seem to boot into the Updating state.
Click to expand...
Click to collapse
Hello
I have exactly the same problem.
OTA with dload doesnt work - dont load ota recovery,just huawei logo loop
fastboot recovery is booted, but when I try steps in main thread I getting Error : Command Not allowed even if I try unlock the bootloader.
Do have somebody solution for it? Every idea is good. I dont want to put this phone to the trash
Thank You

mdoom said:
Hello
I have exactly the same problem.
OTA with dload doesnt work - dont load ota recovery,just huawei logo loop
fastboot recovery is booted, but when I try steps in main thread I getting Error : Command Not allowed even if I try unlock the bootloader.
Do have somebody solution for it? Every idea is good. I dont want to put this phone to the trash
Thank You
Click to expand...
Click to collapse
In Fastboot, is it FRP locked and/or Bootloader locked?

zgfg said:
In Fastboot, is it FRP locked and/or Bootloader locked?
Click to expand...
Click to collapse
both are locked.
When i try to unlock bootloader,i getting the error message.
FRP lock is not possible to unlock becouse phone dont wont start.
any chance?

mdoom2 said:
both are locked.
When i try to unlock bootloader,i getting the error message.
FRP lock is not possible to unlock becouse phone dont wont start.
any chance?
Click to expand...
Click to collapse
That's the problem, when playing with ROMs you must take carw that you keep OEM Unlocked.
Maybe DC-Unlocker (paid) can help
https://www.dc-unlocker.com/DC-Phoenix-flash-repair-tutorial

i bricked my honor, is there anything i can do?

So I had an unlocked H8 with LOS. As I wanted to install EMUI, I put the proper restore Update.app into the dload folder and started Huawei's recovery. Everything went well, I formated data and wanted to install the EMUI 4.1 ROM using the same method.
Unfortunately my H8 is bootlooping and there is now way into erecovery nor any other recovery. It simply reboots on every single known vol up or down key pressing combination. The only thing I can go to is fastboot mode when holding down vol down and plugging in usb wire. But, it says frd locked and I can't install nor boot twrp. It's simply gone and reboots all the time.
Any hints? I can't even turn it off.

I wanted to give away that phone that's the reason. Last time I did it this way, I could flash the EMUI 4.1 since it's signed. But not this time.
Interesting part is, that although fastboot says frd locked, I still get the "phone unlocked" warning on every reboot. dload method isn't working, as it simply keeps rebooting.
It's my hardest brick so far I ever encountered

the same thing happened to me.....on my phone lock/unlocked frp and bootloader were tweaked for some reason(I mean that what was written wasn't the reality) so how did I fix it? I kept on to flash rollback package many times and I tried to unlock/relock bootloader again, at the end the phone let me to flash the firmware, I didn't know how but the phone allowed me to flash things throw recovery(using dload method). At the begin I only could access to erecovery and fastboot. I suppose that I broke system and data partition and while I looked/unlocked the bootloader, the wipe fixed the partition table. Sorry I'm tired and I know that my English sucks, I hope you understand what I have written.

How did you enter erecovery as this isn't working for me.... What did you flash over fastboot?

Have you tried flashing the firmware separately using adb on computer?
For this you just need to extract the Update.app using the firmware extractor for huawei. Then flash them individually using adb commands in cmd.

I can't access any state that would allow to do adb.

faeArai said:
How did you enter erecovery as this isn't working for me.... What did you flash over fastboot?
Click to expand...
Click to collapse
sorry. I'll try to explain better, however on Huawei/honor devices there are not one but two recoveries, so one is the normal recovery flashed in recovery partition, the second one is the Huawei recovery that is flashed in recovery2 partition, so if you didn't touch recovery2 partition, your erecovery is still there, now, if you press VOL+ VOL- and POWER it will reboot to recovery2 and it starts to flash something from dload in your sd card, so in my opinion you should do this things, first try this method to flash rollback package(this is the transition package from 7 to 6 and you will find it on honor site) if this is still not working try locking and unlocking again your bootloader(I hope this fix partitions of your device) then try to enter recovery and do a wipe and then boot your device, if this doesn't work flash rollback package(now it would work) and then flash an emui 4 full firmware image, always using dload method. trust me... I did the same... and it worked for me. let me know if it works for you :good:

faeArai said:
So I had an unlocked H8 with LOS. As I wanted to install EMUI, I put the proper restore Update.app into the dload folder and started Huawei's recovery. Everything went well, I formated data and wanted to install the EMUI 4.1 ROM using the same method.
Unfortunately my H8 is bootlooping and there is now way into erecovery nor any other recovery. It simply reboots on every single known vol up or down key pressing combination. The only thing I can go to is fastboot mode when holding down vol down and plugging in usb wire. But, it says frd locked and I can't install nor boot twrp. It's simply gone and reboots all the time.
Any hints? I can't even turn it off.
Click to expand...
Click to collapse
I ran into this issue not that long ago. What you have to do is relock your bootloader using ADB. The ADB commands and instructions can be found in this thread.
Just a FYI, do not use the links to the software listed in that thread as it is a little outdated. The method still works but the software will probably not work. Just be sure to get the most recent/appropriate version of SuperSU and TWRP via their official threads (This is if you want to re-root). There are Honor 8 specific TWRP files if I remember correctly, so be sure to check around the Honor 8 forums for the correct files.
A quick summary of what I did:
1) Power your phone off and then boot into fastboot by holding Vol down + Power; as soon as it boots up, plug your phone into your combuter via your usb cord.
2) With ADB running, type:
Code:
fastboot oem relock [COLOR="LightBlue"]################[/COLOR]
NOTE: The '#' should be replaced with your unique unlock code that you obtained to unlock your bootloader.
3) Wait for it to format and reset your phone and go through the setup. BE SURE TO BYPASS all google registration; skip everything you can to get into the phone itself. If you do register, it will reactivate FRP and you'll have to start over again.
4) Turn on USB Debugging and every other setting that enables developer administrative navigation and control just to be safe. USB Debugging being the most important one, though.
5) Restart your phone and boot into fastboot again using Vol down + Power.
6) Unlock your phone again with:
Code:
fastboot oem unlock [COLOR="LightBlue"]################[/COLOR]
7) Once the command is entered, it'll reset your phone once more and - as stated before - bypass/skip all google (FRP) registration.
8) Enable developer options and USB debugging again and make sure that OEM Unlocked is checked and grayed out.
9) Reboot into fastboot mode to confirm that FRP is disabled and you should be able to install TWRP now via ADB.

@Numerics thanks. The thing is, that I can't boot anything. I can't even go into eRecovery. Nor can I flash a stock EMUI 4.1. It just boot loops all the time and I can only access fastboot.

If you can flash twrp..........Install los or other Rom ..................Go back to stock.......you must flash b360 ober adb...... because los is 7.1...............if you on b360 you can usw the rollback for emui 4.1........,..............sry for bad english

I can easily go to fastboot. But I can't flash anything. I extracted the img from the update.app but can't flash. It simply says that it's not permitted.

faeArai said:
I can easily go to fastboot. But I can't flash anything. I extracted the img from the update.app but can't flash. It simply says that it's not permitted.
Click to expand...
Click to collapse
With my method, you don't need to flash anything. Just relock your bootloader via adb in fastboot mode and let it reset. Unless I'm not understanding your issue entirely.

@Numerics as I said, in won't boot anything as it is constantly boot looping. There is no way to access any kind of recovery nor erecovery. There is no boot into Android. The only thing accessible right now is fast boot (which is not ADB). But even in fast boot I can't do anything als operations are not permitted.
after boot looping and starting fast boot mode, I can see a "Android reboot reason" section saying:
AP_S_PANIC
data is invalid
There is still a lineageos installed on system as firmware but as I tried to get rid of it by going back to stock EMUI, I guess Huawei's rollback did something wrong and killed recovery (although I did it in the past successfully).
I tried to run HiSuite to recover my phone, but it just says, that my phone is not supported.
Speaking of this, Huawei messed up with that whole fastboot locking bull****.

faeArai said:
@Numerics as I said, in won't boot anything as it is constantly boot looping. There is no way to access any kind of recovery nor erecovery. There is no boot into Android. The only thing accessible right now is fast boot (which is not ADB). But even in fast boot I can't do anything als operations are not permitted.
after boot looping and starting fast boot mode, I can see a "Android reboot reason" section saying:
AP_S_PANIC
data is invalid
There is still a lineageos installed on system as firmware but as I tried to get rid of it by going back to stock EMUI, I guess Huawei's rollback did something wrong and killed recovery (although I did it in the past successfully).
I tried to run HiSuite to recover my phone, but it just says, that my phone is not supported.
Speaking of this, Huawei messed up with that whole fastboot locking bull****.
Click to expand...
Click to collapse
No, I know ADB isn't Fastboot. What I'm trying to say is that you should be able to still run ADB via CMD on Windows when you're in fastboot mode to relock your bootloader with the directions I gave in my previous post. It'll force-restore your phone to a non-bricked/vanilla state. At least that is how I fixed mine.
Like... You can't even try using the 'fastboot oem relock ################' function via the ADB console while in fastboot?

yes boy trust us, you haven't a working OS so it is a normal thing that your phone reboot, you cannot access to recovery because some partitions are corrupted (data partition) , so these are the steps that could help you:
1) using fastboot, relock your boot loader
2)using fastboot, unlock your boot loader (partition table would be ok now, and you would be able to use load method to flash things trow stock recovery)
4)put inside your sd card \dload\update.app(use rollback package)
3) press all the buttons while your device is rebooting(do this before the blue screen logo appear), your phone is now looking for something inside your sd card
5) if the next step doesn't work do a factory reset from recovery that now would be working
6) put inside your sd card a full android 6 (emus 4) update.app and pressing all buttons it will install the firmware
7) your device now is locked and back to stock, maybe without cust partition or maybe in test mode but it is certainly alive
8) do a factory reset and reinstall the firmware
9) your phone is now ok

You don't lock the bootloader via ADB but via fastboot.
As I said, northing was restored and nothing is booting and I can't unlock my bootloader again. As I said, recovery is not working so the file in dload is not loaded and used. Which is strange.
Locking bootloader didn't do anything besides locking the bootloader. Device is still dead and I still can only access fastboot.

faeArai said:
You don't lock the bootloader via ADB but via fastboot.
As I said, northing was restored and nothing is booting and I can't unlock my bootloader again. As I said, recovery is not working so the file in dload is not loaded and used. Which is strange.
Locking bootloader didn't do anything besides locking the bootloader. Device is still dead and I still can only access fastboot.
Click to expand...
Click to collapse
Which model do u own?
Sent from my Honor 8 using XDA Labs

The European one.

faeArai said:
You don't lock the bootloader via ADB but via fastboot.
As I said, northing was restored and nothing is booting and I can't unlock my bootloader again. As I said, recovery is not working so the file in dload is not loaded and used. Which is strange.
Locking bootloader didn't do anything besides locking the bootloader. Device is still dead and I still can only access fastboot.
Click to expand...
Click to collapse
This is not the truth.....locking bootloader will erase all your data and fix partitions....and with fixed partition you can access to recovery ......trust me the only thing that you can do is to lock your bootloader......you can't flash anything from fastboot and boot recovery or system now...... lock your bootloader and then unlock it again, try using "fastboot OEM lock *****" or "fastboot OEM relock *******" (try cmd runned as admin, people say that this makes the difference) then unlock your device again and .....magic your recovery will boot......the same thing happened to me and I fixed my phone using this trick, however, even if you had frp unlocked it would say you that isn't possible to write anything because you broke some partition, and that's the reason why you can't boot recovery, wait one second and think: why doesn't my recovery boot?

It has nothing to do with trust. I did it and device is still a full stone brick. Nothing changed by locking the bootloader besides that now I can't unlock the bootloader anymore.

Mate 9 ERROR Mode

Hello,
following problem:
Mate 9 (MHA-L29C432). Had an update on Android 8 (Oreo) made. It was perfect too. But when I did not manage to install Magisk, I did a backup of Flashfire via TWRP version B194 (Boot, Recovery, System).
Flashfire, by that I mean the program for backup and restore.
Now the phone starts in Fastboot mode, but looks different:
ERROR fashion
Attention!
Please update system again
Error!
Func NO: 15 (bl31 image)
Error NO: 1 (security verify failed!)
I can not turn off the phone !!! It always starts again, with the above screen.
It is also not possible to boot into recovery or eRecovery.
And with the above message, my PC recognizes no more device. So Fastboot still download mode is not possible.
What can I do? Can it be because of the partions, because Android 7 and 8 have other partion names?

Sorry u must write in english here!
Du musst in English schreiben hier!

My German is not very good, so you'll have to translate this if you need to.
You should still be able to boot to fastboot mode.
However, that error seems to refer to /system partition, and it has triggered AVB or verity.
I would try flashing stock system.img using fastboot, download your Oreo firmware from http://pro-teammt.ru/firmware-database/ and extract update.app, then extract system partition from it using Huawei Update Extractor. Alternatively, if Huawei Update Extractor gives you errors like it did to me, use this: https://github.com/marcominetti/split_updata.pl (you need perl for this, I use Strawberry).
When you have system extracted, flash it in fastboot using fastboot flash system system.img.
Do the same with KERNEL, extract and flash to fastboot flash kernel KERNEL.IMG
(BOOT is now split into RAMDISK and KERNEL)
(And flash recovery_ramdisk, recovery_kernel, erecovery_ramdisk, erecovery_kernel too.)
And you're not actually starting in fastboot mode, it's error mode.
You have to plug in usb and reboot and hold volume down to get to fastboot.

Thanks for the answers.
The problem is, no matter what I do, the Hamdy does not start in Fastboot. It always comes error mode. I can not turn off the phone, so far, it always showed the error mode and always starts again by itself. But now, I think, the battery is running low.

laptop45307 said:
Thanks for the answers.
The problem is, no matter what I do, the Hamdy does not start in Fastboot. It always comes error mode. I can not turn off the phone, so far, it always showed the error mode and always starts again by itself. But now, I think, the battery is running low.
Click to expand...
Click to collapse
Try plugging USB in, hold volume down and power down for a while. A while can be a minute or 2. I don't remember how long I had to hold it when I got ERROR MODE.
Alternatively you could maybe let it run out of battery, hold down volume down and plug in USB. It should get you to fastboot as soon as it starts.
Does it display different errors when you try to boot recovery/eRecovery? It should say Func error: recovery or eRecovery. If it doesn't, just keep pressing power until it does reboot and be ready with volume buttons.

Hello, battery is empty. As soon as I press the volume button and connect USB, the error mode appears. If I keep it pressed, the device restarts again and again after a few seconds. Again and again with the error mode.

laptop45307 said:
Hello, battery is empty. As soon as I press the volume button and connect USB, the error mode appears. If I keep it pressed, the device restarts again and again after a few seconds. Again and again with the error mode.
Click to expand...
Click to collapse
Have you figured it out or still looking for solution. Because I'm now in the same situation. Just error no is 14.

Ditto here , two error numbers 11 and 2. 11 is recovery and 2 is load failed!

laptop45307 said:
Hello, battery is empty. As soon as I press the volume button and connect USB, the error mode appears. If I keep it pressed, the device restarts again and again after a few seconds. Again and again with the error mode.
Click to expand...
Click to collapse
any progress?
---------- Post added at 07:38 PM ---------- Previous post was at 07:34 PM ----------
sgtduckyboy said:
Ditto here , two error numbers 11 and 2. 11 is recovery and 2 is load failed!
Click to expand...
Click to collapse
fixed?

yes, forgot to update. when my battery died down, i put it on a charger as it got up a few percent , I then held the volume down and power buttons,, booted right up to erecovery! downloaded nougat, installed and it immediately gave me the Oreo update, so i took it, been running great for a week or more now!

Sorry for gravedigging, but I am having the same problem. I followed ante0´s directions but i cant flash system cause the command is not allowed (FRP Lock). Any chance to get it running again?

laptop45307 said:
Hello, battery is empty. As soon as I press the volume button and connect USB, the error mode appears. If I keep it pressed, the device restarts again and again after a few seconds. Again and again with the error mode.
Click to expand...
Click to collapse
Hi, I was having the same problem. Mate 8 EMUI 8.
After looking everywhere and trying all the options available, I wasnt able to resolve.
Finally, I tried FunkyHuawei and got my system back through eRecovery.
Gave them the readings like version no. , build no...etc through fastboot. The required info is on their site. They then reverted with a link of the firmware which I flashed through their FuHunbrick tool. It force updates the entire full last version.
After flashing and booting, the system didnt boot but was able to go to eRecovery and restored my previous version.
If you or anyone else stuck at this error, they can try at their own risk as they dont guarantee anything.
Edit: you should and will be able to boot into fastboot once the battery is totally down and phone shuts off completely. Just press volume down button and insert usb. Try again and again if it doesnt work first time.
Thanks.

Boot brick - Can't power off, can't get to erecovery or recovery after rollback

Hey guys, my Honor is in brick state. I pushed a rollback package while I was in marshmallow (but with wrong ROM, so I was trying to rollback again and retry the procedure) and the phone got stuck in Honor blue screen at loop.
It won't let me power off, it justs turns on again. All button combinations won't work apparently. I can't get to recovery or e-recovery.
I tried depleting the battery. But as soon as I connect to the charger, it powers on. If I try the button combination before putting charge, it also doesn't work.
After the first successful rollback to MM, I think the bootloader got locked.
adb and fastbook can't seem to list the device.
I can get to fastboot and rescue mode, but I don't know the procedure from there.
So, is this a unsolvable brick? Or is there anything else that can be done to save this phone?
Thanks a lot for your feedback.

use dc unlocker to flash unlock bootloader and after dc flasher

valp88 said:
Hey guys, my Honor is in brick state. I pushed a rollback package while I was in marshmallow (but with wrong ROM, so I was trying to rollback again and retry the procedure) and the phone got stuck in Honor blue screen at loop.
It won't let me power off, it justs turns on again. All button combinations won't work apparently. I can't get to recovery or e-recovery.
I tried depleting the battery. But as soon as I connect to the charger, it powers on. If I try the button combination before putting charge, it also doesn't work.
After the first successful rollback to MM, I think the bootloader got locked.
adb and fastbook can't seem to list the device.
I can get to fastboot and rescue mode, but I don't know the procedure from there.
So, is this a unsolvable brick? Or is there anything else that can be done to save this phone?
Thanks a lot for your feedback.
Click to expand...
Click to collapse
It's easy. I had a similar problem too. Just when your phone attempts to boot, hold the Volume Down button and immediately connect it to the PC (within 1-2 second). It should go into fastboot mode. Now, open Huawei Multi Tool and unlock your bootloader then use the tool to unbrick your phone, start with flashing stock recovery and then the correct firmware.

SirDarknight said:
It's easy. I had a similar problem too. Just when your phone attempts to boot, hold the Volume Down button and immediately connect it to the PC (within 1-2 second). It should go into fastboot mode. Now, open Huawei Multi Tool and unlock your bootloader then use the tool to unbrick your phone, start with flashing stock recovery and then the correct firmware.
Click to expand...
Click to collapse
Thanks for repying. I unlocked my bootloader through fastboot and I'm trying to get multi-tool now!
i'm getting 404 from xda for the download link though.

SirDarknight said:
It's easy. I had a similar problem too. Just when your phone attempts to boot, hold the Volume Down button and immediately connect it to the PC (within 1-2 second). It should go into fastboot mode. Now, open Huawei Multi Tool and unlock your bootloader then use the tool to unbrick your phone, start with flashing stock recovery and then the correct firmware.
Click to expand...
Click to collapse
I flashed extracted and flashed images for B131 and B360, without luck. Stuck on the unlocked warning now: "Your device is booting now".
I can't seem to get to erecovery. Please let me know if you have any ideas.

valp88 said:
I flashed extracted and flashed images for B131 and B360, without luck. Stuck on the unlocked warning now: "Your device is booting now".
I can't seem to get to erecovery. Please let me know if you have any ideas.
Click to expand...
Click to collapse
If you're stuck on "Your device is booting now". This probably means your recovery is screwed. Don't worry, flash stock recovery and erecovery using Multi-Tool.
Then try the dload method. If the problem persists, then flash the correct TWRP then use HuRUpdater to flash the ROM you want. This will definitely fix the issue.

SirDarknight said:
If you're stuck on "Your device is booting now". This probably means your recovery is screwed. Don't worry, flash stock recovery and erecovery using Multi-Tool.
Then try the dload method. If the problem persists, then flash the correct TWRP then use HuRUpdater to flash the ROM you want. This will definitely fix the issue.
Click to expand...
Click to collapse
The recovery images from Multi-Tool servers seem to work! Thanks a lot. I was able to get to erecovery, now I'll proceed as decribed by you! :good::good::good:
Edit: dload failed at 99%, but I was able to factory reset and get to the system after all!