Hello,
following problem:
Mate 9 (MHA-L29C432). Had an update on Android 8 (Oreo) made. It was perfect too. But when I did not manage to install Magisk, I did a backup of Flashfire via TWRP version B194 (Boot, Recovery, System).
Flashfire, by that I mean the program for backup and restore.
Now the phone starts in Fastboot mode, but looks different:
ERROR fashion
Attention!
Please update system again
Error!
Func NO: 15 (bl31 image)
Error NO: 1 (security verify failed!)
I can not turn off the phone !!! It always starts again, with the above screen.
It is also not possible to boot into recovery or eRecovery.
And with the above message, my PC recognizes no more device. So Fastboot still download mode is not possible.
What can I do? Can it be because of the partions, because Android 7 and 8 have other partion names?
Sorry u must write in english here!
Du musst in English schreiben hier!
My German is not very good, so you'll have to translate this if you need to.
You should still be able to boot to fastboot mode.
However, that error seems to refer to /system partition, and it has triggered AVB or verity.
I would try flashing stock system.img using fastboot, download your Oreo firmware from http://pro-teammt.ru/firmware-database/ and extract update.app, then extract system partition from it using Huawei Update Extractor. Alternatively, if Huawei Update Extractor gives you errors like it did to me, use this: https://github.com/marcominetti/split_updata.pl (you need perl for this, I use Strawberry).
When you have system extracted, flash it in fastboot using fastboot flash system system.img.
Do the same with KERNEL, extract and flash to fastboot flash kernel KERNEL.IMG
(BOOT is now split into RAMDISK and KERNEL)
(And flash recovery_ramdisk, recovery_kernel, erecovery_ramdisk, erecovery_kernel too.)
And you're not actually starting in fastboot mode, it's error mode.
You have to plug in usb and reboot and hold volume down to get to fastboot.
Thanks for the answers.
The problem is, no matter what I do, the Hamdy does not start in Fastboot. It always comes error mode. I can not turn off the phone, so far, it always showed the error mode and always starts again by itself. But now, I think, the battery is running low.
laptop45307 said:
Thanks for the answers.
The problem is, no matter what I do, the Hamdy does not start in Fastboot. It always comes error mode. I can not turn off the phone, so far, it always showed the error mode and always starts again by itself. But now, I think, the battery is running low.
Click to expand...
Click to collapse
Try plugging USB in, hold volume down and power down for a while. A while can be a minute or 2. I don't remember how long I had to hold it when I got ERROR MODE.
Alternatively you could maybe let it run out of battery, hold down volume down and plug in USB. It should get you to fastboot as soon as it starts.
Does it display different errors when you try to boot recovery/eRecovery? It should say Func error: recovery or eRecovery. If it doesn't, just keep pressing power until it does reboot and be ready with volume buttons.
Hello, battery is empty. As soon as I press the volume button and connect USB, the error mode appears. If I keep it pressed, the device restarts again and again after a few seconds. Again and again with the error mode.
laptop45307 said:
Hello, battery is empty. As soon as I press the volume button and connect USB, the error mode appears. If I keep it pressed, the device restarts again and again after a few seconds. Again and again with the error mode.
Click to expand...
Click to collapse
Have you figured it out or still looking for solution. Because I'm now in the same situation. Just error no is 14.
Ditto here , two error numbers 11 and 2. 11 is recovery and 2 is load failed!
laptop45307 said:
Hello, battery is empty. As soon as I press the volume button and connect USB, the error mode appears. If I keep it pressed, the device restarts again and again after a few seconds. Again and again with the error mode.
Click to expand...
Click to collapse
any progress?
---------- Post added at 07:38 PM ---------- Previous post was at 07:34 PM ----------
sgtduckyboy said:
Ditto here , two error numbers 11 and 2. 11 is recovery and 2 is load failed!
Click to expand...
Click to collapse
fixed?
yes, forgot to update. when my battery died down, i put it on a charger as it got up a few percent , I then held the volume down and power buttons,, booted right up to erecovery! downloaded nougat, installed and it immediately gave me the Oreo update, so i took it, been running great for a week or more now!
Sorry for gravedigging, but I am having the same problem. I followed ante0´s directions but i cant flash system cause the command is not allowed (FRP Lock). Any chance to get it running again?
laptop45307 said:
Hello, battery is empty. As soon as I press the volume button and connect USB, the error mode appears. If I keep it pressed, the device restarts again and again after a few seconds. Again and again with the error mode.
Click to expand...
Click to collapse
Hi, I was having the same problem. Mate 8 EMUI 8.
After looking everywhere and trying all the options available, I wasnt able to resolve.
Finally, I tried FunkyHuawei and got my system back through eRecovery.
Gave them the readings like version no. , build no...etc through fastboot. The required info is on their site. They then reverted with a link of the firmware which I flashed through their FuHunbrick tool. It force updates the entire full last version.
After flashing and booting, the system didnt boot but was able to go to eRecovery and restored my previous version.
If you or anyone else stuck at this error, they can try at their own risk as they dont guarantee anything.
Edit: you should and will be able to boot into fastboot once the battery is totally down and phone shuts off completely. Just press volume down button and insert usb. Try again and again if it doesnt work first time.
Thanks.
Related
Hi all,
I installed the TWRP recovery for my mate 7 - 09 version, with lollipop 5.1. But then I unknowingly wiped something I shouldn't have: I think it was the system folder. No backups were made
My phone keeps starting up to the huawei logo and then reboots\turns off. I can get into fastboot&rescue mode, but that's it. No recovery, no 3-button fix (as far as I know).
The second problem is that I cannot get my device to be recognised by my pc. adb devices doesn't give me any results.
I don't feel like I can install the drivers properly as well. Pherhaps thats the problem? How can I do this? I have a driversetup from a mate7 download, but double clicking it doesnt show any prompts.
Anyone who can help me in any way is more than welcome!
dekraan said:
Hi all,
I installed the TWRP recovery for my mate 7 - 09 version, with lollipop 5.1. But then I unknowingly wiped something I shouldn't have: I think it was the system folder. No backups were made
My phone keeps starting up to the huawei logo and then reboots\turns off. I can get into fastboot&rescue mode, but that's it. No recovery, no 3-button fix (as far as I know).
The second problem is that I cannot get my device to be recognised by my pc. adb devices doesn't give me any results.
I don't feel like I can install the drivers properly as well. Pherhaps thats the problem? How can I do this? I have a driversetup from a mate7 download, but double clicking it doesnt show any prompts.
Anyone who can help me in any way is more than welcome!
Click to expand...
Click to collapse
Hey Buddy, here's what you can try to do:
1.) Boot connect your phone to your computer.
2.) Next, boot your phone to fastboot.
3.) Next, open command prompt from the folder where your ADB files are stored.
4.)On CMD type:
fastboot devices
5.) If your device appears then you have 2 options now. You can either:
a.) Flash Stock recovery.img or
b.) Flash back TWRP
6.) If choosing option a.) you can then save stock firmware within dload folder on your external sd card then force upgrade via 3 btn method.
7.) If choosing option b.) you can boot to twrp then either sideload a custom rom or try to save on your external sd and flash
blitzkriegger said:
Hey Buddy, here's what you can try to do:
1.) Boot connect your phone to your computer.
2.) Next, boot your phone to fastboot.
3.) Next, open command prompt from the folder where your ADB files are stored.
4.)On CMD type:
fastboot devices
5.) If your device appears then you have 2 options now. You can either:
a.) Flash Stock recovery.img or
b.) Flash back TWRP
6.) If choosing option a.) you can then save stock firmware within dload folder on your external sd card then force upgrade via 3 btn method.
7.) If choosing option b.) you can boot to twrp then either sideload a custom rom or try to save on your external sd and flash
Click to expand...
Click to collapse
I'll give that a try, thank you. With step 1, you just mean: connect the phone through usb to the computer, right?
When I rooted the phone, I did so on my work laptop, so I am hoping I can get it recognised there, but lets see what happens at home.
EDIT:
Ok, i've typed in fastboot devices, and it gave me one line with a 16-digit code (numbers and letters) some white space and then the word fastboot. What does that mean?
That should meen it recognizes your phone in fastboot mode. Next step is to flash as stated in step 5 that in the instructions.
Sent from my HUAWEI MT7-L09 using Tapatalk
dekraan said:
I'll give that a try, thank you. With step 1, you just mean: connect the phone through usb to the computer, right?
When I rooted the phone, I did so on my work laptop, so I am hoping I can get it recognised there, but lets see what happens at home.
EDIT:
Ok, i've typed in fastboot devices, and it gave me one line with a 16-digit code (numbers and letters) some white space and then the word fastboot. What does that mean?
Click to expand...
Click to collapse
EDIT AGAIN:
Ok, this is what I did. I downloaded the well known mate7 package, extracted the b119 tools folder and I put the twrp_2.8.7.0_mate7_5.1.img file from this forum (the TWRP for 5.1) inside this folder.
Then, I open cmd inside the folder, and I typed: fastboot flash recovery twrp_2.8.7.0_mate7_5.1.img. This is what happens:
target reported max download size of 471859200 bytes
sending 'recovery'(12644 KB)...
OKAY [ 1.302s]
writing 'recovery'...
OKAY [ 0.455s]
finished. total time: 1.756s
Now, I finally managed to get back into TWRP! I've only got 2% battery though (but I see a + which I think means charging...EDIT: yes, it is on 3% now. Better leave it like this...).
It tells me this:
TWRP has detected an unmodified system partition.
TWRP can leave your system partition unmodified to make it easier for you to take official updates. TWRP will be unable to prevent the stock rom from replacing TWRP and will not offer to root your device. Installing zips or performing adb operations may still modify the system partition.
I decided to swipe, to allow modifications.
So, I've got twrp back! For lollipop. This probably means I have to flash the lollipop rom? I will download the update.zip file next and put it on my sd card (using my pc and a microsd adapter...)
Keep you posted!
Ok, this is not working.
I put update.zip on my sd-card, and tried to install it. This is what I get:
Installing 'sd-ext/update.zip'...
checking for MD5 file...
Skipping MD5 check: no MD5 file found
E:unknown command [errno]
file_getprop: failed to stat
E: error executing updater binary in zup 'sd-ext/update.zip'
Error flashing zip 'sd-ext/update.zip'...
Updating partition details...
...done
EDIT:
I tried to sideload but on my pc I get:
error: protocol fault (no status)
And on my TWRP I get:
You need adb 1.0.32 or newer to sideload to this device.
EDIT:
Updated my adb to 1.0.32 for windows, and rebooted everything. Now i'm at 6% of sideload. Hoping this will work!
EDITn the PC everything seems to go ok, but on my phone it says: E:Zip signature verification failed:1
What should I try next?
dekraan said:
Ok, this is not working.
I put update.zip on my sd-card, and tried to install it. This is what I get:
Installing 'sd-ext/update.zip'...
checking for MD5 file...
Skipping MD5 check: no MD5 file found
E:unknown command [errno]
file_getprop: failed to stat
E: error executing updater binary in zup 'sd-ext/update.zip'
Error flashing zip 'sd-ext/update.zip'...
Updating partition details...
...done
EDIT:
I tried to sideload but on my pc I get:
error: protocol fault (no status)
And on my TWRP I get:
You need adb 1.0.32 or newer to sideload to this device.
EDIT:
Updated my adb to 1.0.32 for windows, and rebooted everything. Now i'm at 6% of sideload. Hoping this will work!
EDITn the PC everything seems to go ok, but on my phone it says: E:Zip signature verification failed:1
What should I try next?
Click to expand...
Click to collapse
I don't advise you to flash lollipop firmware first. It's more prudent to go back to kitkat first as I believe Lollipop needs kitkat as base
1.) Put stock kitkat update.app on dload folder of your memory card. Also make sure you have the LO9 stock kitkat recovery.
2.) With your phone connected to pc, go to twrp and reboot to bootloader.
3.) Once on bootloader open cmd on your tools folder then fastboot flash the stock kitkat recovery.
4.) Once done, fastboot reboot then force upgrade to install stock firmware.
5.) Once you have stock kitkat follow the drill to reach lollipop
blitzkriegger said:
I don't advise you to flash lollipop firmware first. It's more prudent to go back to kitkat first as I believe Lollipop needs kitkat as base
1.) Put stock kitkat update.app on dload folder of your memory card. Also make sure you have the LO9 stock kitkat recovery.
2.) With your phone connected to pc, go to twrp and reboot to bootloader.
3.) Once on bootloader open cmd on your tools folder then fastboot flash the stock kitkat recovery.
4.) Once done, fastboot reboot then force upgrade to install stock firmware.
5.) Once you have stock kitkat follow the drill to reach lollipop
Click to expand...
Click to collapse
Hi, thank you for your advice. I have but one question remaining: what stock kitkat update should I use? And where can I find the right recovery that goes with it?
I've tried several recovery_stock.img I found, and it does take away TWRP, so it might have done the trick. Only problem is that I cannot force upgrade to install whats on my sd-card....The phone keeps turning on (after a long push) and after seeing the logo for a little while, it turns off (short vibration)... Is there another way?
dekraan said:
Hi, thank you for your advice. I have but one question remaining: what stock kitkat update should I use? And where can I find the right recovery that goes with it?
I've tried several recovery_stock.img I found, and it does take away TWRP, so it might have done the trick. Only problem is that I cannot force upgrade to install whats on my sd-card....The phone keeps turning on (after a long push) and after seeing the logo for a little while, it turns off (short vibration)... Is there another way?
Click to expand...
Click to collapse
You should flash B137SP03 firmware. You can also refer to this guide:
http://forum.xda-developers.com/mate-7/help/5-1-to-4-4-2-bootloop-t3132888
1.)Prepare the Stock B137SP03 firmware on your SD card
2.)Download the fastboot.zip guide and extract it to a separate folder.
3.) next connect your phone to your computer and go to fastboot mode.
4.) Flash the boot.img and recovery.img you find on that guide.
5.) Once done, do the force upgrade with the B137 firmware.
blitzkriegger said:
You should flash B137SP03 firmware. You can also refer to this guide:
http://forum.xda-developers.com/mate-7/help/5-1-to-4-4-2-bootloop-t3132888
1.)Prepare the Stock B137SP03 firmware on your SD card
2.)Download the fastboot.zip guide and extract it to a separate folder.
3.) next connect your phone to your computer and go to fastboot mode.
4.) Flash the boot.img and recovery.img you find on that guide.
5.) Once done, do the force upgrade with the B137 firmware.
Click to expand...
Click to collapse
I've followed the guide you are reffering to. And I flashed the boot and recovery, and managed to get the roll back force installed. But for the life of me, I cannot get my phone to force install the B137 zip. I just can't get into force install mode. Are there tips or tricks? I am holding power up and down, and then press power untill I feel a short vibration. But all it does it show me the huawei logo screen and then shuts down again.
Very frustrating!
EDIT:
ok, I noticed that when my sd-card is not inserted, the phone easily boots into the force install mode. It shows the logo for a couple of seconds, screen goes black and then the force install loads. So this is what I did: insert the sd card half way, press vol up and down, and power on. Then after the logo when the screen goes black, insert the sd-card all the way and when the phone goes to force install mode, it can find the update!
Now installing.... hope this helps someone else out there!
Worked! And I am up and running again! Thank you for saving my mate
I got my Mate bricked and i've been trying to figure out how to solve it. I tried lots of things from different guides, but just an hour ago I found this guide and it worked! I can't tell you how happy I am right now, thanks guys!
aleksik said:
I got my Mate bricked and i've been trying to figure out how to solve it. I tried lots of things from different guides, but just an hour ago I found this guide and it worked! I can't tell you how happy I am right now, thanks guys!
Click to expand...
Click to collapse
Glad to hear both of you guys have your mates up and running again. As long as a phone turns on and is not dead as a brick there's always hope it can be restored
Hi everyone, I have the same problem with my mate 7, i was messing with unlocking bootloader(which I succesfully have done), couldn't get my phone rooted so installed TWRP recovery for Lollipop(which was already installed when i bought the phone). Ended up with soft bricked phone(no OS, no recovery at all).
I tried different tutorials how to fix it, none of them worked(including that one unfortunatelly).
I have taken some pictures to show you what the problem is but cannot post them until reach 10 posts on forum
Basically, i can get into fastboot mode by holding volume down with power button. Windows and Hisuite don't recognise my device but in fastboot mode i can check devices connected. Typing "fastboot devices" i get "P6Q7M14A15008421 fastboot", which i guess is my device indeed.
After that i try flashing boot.img and recovery.img(which are reported OK). Then rebooting with 3 button(vol up and down, power) and Huawei logo screen appears for a bit and goes into white screen saying "rescue mode" and at the bottom: "Error Func NO: 10(FUNC_BOOT_RECOVERY) Error NO:2". Trying rebooting into recovery mode(vol up and power) it shows similar "recovery mode" screen but with different errors: "Error! Func NO:12(FUNC_LOAD_IOM3) Error NO:1".
That's it! It seems like i cannot flash my device successfully for some reason. What Windows version did you guys use?? I tried Win 8.0 and Win 10, maybe i should use older systems? Please help, i had my phone for a week only and broke it(
I can't help you much because I don't have enough knowledge about these kind of things.. I use Windows 7 and from my previous experiences I can say that working with Windows 8 can be frustrating. PS. I bricked my Mate 12hrs after buying it
muzammil84 said:
Hi everyone, I have the same problem with my mate 7, i was messing with unlocking bootloader(which I succesfully have done), couldn't get my phone rooted so installed TWRP recovery for Lollipop(which was already installed when i bought the phone). Ended up with soft bricked phone(no OS, no recovery at all).
I tried different tutorials how to fix it, none of them worked(including that one unfortunatelly).
I have taken some pictures to show you what the problem is but cannot post them until reach 10 posts on forum
Basically, i can get into fastboot mode by holding volume down with power button. Windows and Hisuite don't recognise my device but in fastboot mode i can check devices connected. Typing "fastboot devices" i get "P6Q7M14A15008421 fastboot", which i guess is my device indeed.
After that i try flashing boot.img and recovery.img(which are reported OK). Then rebooting with 3 button(vol up and down, power) and Huawei logo screen appears for a bit and goes into white screen saying "rescue mode" and at the bottom: "Error Func NO: 10(FUNC_BOOT_RECOVERY) Error NO:2". Trying rebooting into recovery mode(vol up and power) it shows similar "recovery mode" screen but with different errors: "Error! Func NO:12(FUNC_LOAD_IOM3) Error NO:1".
That's it! It seems like i cannot flash my device successfully for some reason. What Windows version did you guys use?? I tried Win 8.0 and Win 10, maybe i should use older systems? Please help, i had my phone for a week only and broke it(
Click to expand...
Click to collapse
Sounds like the wrong boot.img or recovery.img has been flashed. May I know what Mate 7 model you have and which Lollipop firmwre version your phone came last with?
Try to obtain boot.img and revoery.img for your lollipop version then flash that via fastboot
blitzkriegger said:
Sounds like the wrong boot.img -recovery.img has been flashed. May I know what Mate 7 model you have and which Lollipop firmwre version your phone came last with?
Try to obtain boot.img and revoery.img for your lollipop version then flash that via fastboot
Click to expand...
Click to collapse
My phone mt7-09l, european version 16gb. Came with lollipop 5.1 when I bought it but I think I have formatted it via twrp recovery so it shouldn't matter what boot and recovery version I am trying to flash, should it? I'll extract boot and recovery from b308 today andtry that, see if this works. If not, only thing I can try is using win7 and that's it really, no more possibilities
dekraan said:
I've followed the guide you are reffering to. And I flashed the boot and recovery, and managed to get the roll back force installed. But for the life of me, I cannot get my phone to force install the B137 zip. I just can't get into force install mode. Are there tips or tricks? I am holding power up and down, and then press power untill I feel a short vibration. But all it does it show me the huawei logo screen and then shuts down again.
Very frustrating!
EDIT:
ok, I noticed that when my sd-card is not inserted, the phone easily boots into the force install mode. It shows the logo for a couple of seconds, screen goes black and then the force install loads. So this is what I did: insert the sd card half way, press vol up and down, and power on. Then after the logo when the screen goes black, insert the sd-card all the way and when the phone goes to force install mode, it can find the update!
Now installing.... hope this helps someone else out there!
Click to expand...
Click to collapse
I'm stuck on this stage, no errors while flashing but no boot either. Shows logo then like a spark a bit of music and animation (1 sec maybe) and reboot, so on and on and on...
muzammil84 said:
My phone mt7-09l, european version 16gb. Came with lollipop 5.1 when I bought it but I think I have formatted it via twrp recovery so it shouldn't matter what boot and recovery version I am trying to flash, should it? I'll extract boot and recovery from b308 today andtry that, see if this works. If not, only thing I can try is using win7 and that's it really, no more possibilities
Click to expand...
Click to collapse
If you were on Lollipop when everything went sour, you should do what I did, thanks to advice from @blitzkriegger:
You should flash B137SP03 firmware. You can also refer to this guide:
http://forum.xda-developers.com/mate...tloop-t3132888
1.)Prepare the Stock B137SP03 firmware on your SD card
2.)Download the fastboot.zip guide and extract it to a separate folder.
3.) next connect your phone to your computer and go to fastboot mode.
4.) Flash the boot.img and recovery.img you find on that guide.
5.) Once done, do the force upgrade with the B137 firmware.
I used the full steps from the link in there: flashed the right boot and recovery through fastboot. Then I flashed the rollback zip from my sd-card, and then I flashed the B137 zip from my sd-card. I can't tell you more about it, obviously
brack11 said:
I'm stuck on this stage, no errors while flashing but no boot either. Shows logo then like a spark a bit of music and animation (1 sec maybe) and reboot, so on and on and on...
Click to expand...
Click to collapse
Been there, done that. Very frustrating! I've tried several things, none of which are probably the right way, but they worked for me. sometimes....
Can you get into stock recovery (vol+ and power)? What I tried several times was wipe cache, and then hold the powerbutton untill my phone turned off. That worked occasionally to get the device totally turned off. Then try to get to force update with your sd-card half way in, and flip it in totally when the logo dissapears and the screen is black. I also tried to shut down the constant starting up by going into fastboot/recovery mode and then holding power down. As long as it takes. Good luck! And hopefully someone can give you proper advice...
Any advice would be nice.
This is the error message that I get when my phone automatically boots to "RESCUE MODE"
Error!
Func NO:12 (FUNC_LOAD_IOM3)
Error NO:1"
I can boot to fast boot and it automatically boots to RESCUE MODE. I can not boot to recovery, just goes straight to RESCUE MODE. I can do the 3 button manual upgrade method but all it does is boot to the logo screen for about 15 seconds then goes right to the RESCUE MODE. It does not make any indication during the 3 button method when the logo screen is up that it is doing anything. I have the firmware on my SD card in the slot. Its on the root of SD card in a folder named " dload" . I've used this method before to restore it so I know how to do the procedure. But this is the first time I get this error and the first time it doesn't perform the upgrade. I've been at this trying and researching everything for about 6 .months now. No answer. I've email Huawei customer service. No answer. I've pushed thru fast boot the recoveries (CM, and stock ) still can't boot to recovery. Every time I fast boot flash recovery it says "successful ". But can't boot to it. I can fast boot boot.IMG , system.img , etc. But still can't get it to do anything.
But like I said I do have FASTBOOT and RESCUE MODE . any help would be greatly appreciated. Please.
Really nobody has any advice. No one has solved this problem yet
So I guess I'm the only one experiencing this. Riiigghhhttt
Have you tried factory reset?
Press very long to volume up and the power button at same time and after you see the logo press only volume up
mattwheat said:
Any advice would be nice.
This is the error message that I get when my phone automatically boots to "RESCUE MODE"
Error!
Func NO:12 (FUNC_LOAD_IOM3)
Error NO:1"
I can boot to fast boot and it automatically boots to RESCUE MODE. I can not boot to recovery, just goes straight to RESCUE MODE. I can do the 3 button manual upgrade method but all it does is boot to the logo screen for about 15 seconds then goes right to the RESCUE MODE. It does not make any indication during the 3 button method when the logo screen is up that it is doing anything. I have the firmware on my SD card in the slot. Its on the root of SD card in a folder named " dload" . I've used this method before to restore it so I know how to do the procedure. But this is the first time I get this error and the first time it doesn't perform the upgrade. I've been at this trying and researching everything for about 6 .months now. No answer. I've email Huawei customer service. No answer. I've pushed thru fast boot the recoveries (CM, and stock ) still can't boot to recovery. Every time I fast boot flash recovery it says "successful ". But can't boot to it. I can fast boot boot.IMG , system.img , etc. But still can't get it to do anything.
But like I said I do have FASTBOOT and RESCUE MODE . any help would be greatly appreciated. Please.
Click to expand...
Click to collapse
Same problem here. Please help!
I am in the same case, fasboot recognized by my pc but not the adb and Windows doesn't find the good driver.
Envoyé de mon V919 Air DualOS en utilisant Tapatalk
Connect your phone to pc. press vol down and power buttons
Huawei Mate 7 TL10 Android 7.0 Nutella Cihazımdan Tapatalk Kullanılarak Gönderildi
I have a mate 7 tl09, and I have always try this.
I can do in fastboot, but by the way my phone is not detected in adb!
Envoyé de mon Y5 en utilisant Tapatalk
Yes I've done the power + volume buttons. I've tried the manual update method , i can get into fast boot but nothing will flash but recoveries and a couple of the partitions. But it does me no good to flash recoveries stock or custom because no matter what combination of volume buttons and power button I do it either sends me right back to the "Rescue Mode" or " fastboot".I can NOT boot normally NOR can I boot into any recovery. I can NOT flash any system.IMG or data partitions. It errors out soon after I start to flash.
Any luck? I am now getting the same error after trying to flash some extracted .img files through fastboot.
Same problem here with my Mate-7...
Has anyone figured out a solution for this problem? Any ideas? Any thoughts on what exactly I should "fastboot flash" or "fastboot update" to this device ? It won't let me do either one with the full "update" package or a full ROM. I can "fastboot flash" a system.IMG and boot.IMG and recovery.IMG. but still won't boot to anything but "rescue mode" or "fastboot mode". Tried all the different combinations of the update 3 button method. With sdcard half way in, all the way in, with ketchup, standing on my head. But nothing works. It sits on the Huawei boot logo screen for 15 seconds like its trying but then right back to " rescue mode".
From what I've read on the Chinese forums, back to Huawei for new main board. Huawei programmers suck.
mattwheat said:
Has anyone figured out a solution for this problem? Any ideas? Any thoughts on what exactly I should "fastboot flash" or "fastboot update" to this device ? It won't let me do either one with the full "update" package or a full ROM. I can "fastboot flash" a system.IMG and boot.IMG and recovery.IMG. but still won't boot to anything but "rescue mode" or "fastboot mode". Tried all the different combinations of the update 3 button method. With sdcard half way in, all the way in, with ketchup, standing on my head. But nothing works. It sits on the Huawei boot logo screen for 15 seconds like its trying but then right back to " rescue mode".
Click to expand...
Click to collapse
Hi, you can fix it. İ explain,
1. Download this and extract https://mega.nz/#!BhgTyCZb!oUvS6UDhcsp54xCy5x8kvldPgBC43XHH5yGSWRdQF3w
2. Download it and extract your last rom on your phone running.
https://mega.nz/#!g9oV3QAL!cJpqYOfvxDCaO3tQq15hPHyl1rpuZPpX9yKMdQGSYfo
3. Connect your phone to pc with usb cable. And press vol - and power buttons.
4. Your phone will open fastboot menu. And flash the rom your last runnig rom on your phone. (Go to first link)
İf you dont fix it, i can help you
Huawei Mate 7 TL10 Cihazimdan Yollamişam
Does this work on TL09?
fooshack said:
Does this work on TL09?
Click to expand...
Click to collapse
Remember your last update. İt must work. İ get back my phone a number of times
Huawei Mate 7 TL10 Cihazimdan Yollamişam
I'm sorry but I don't understand what you are saying. It obviously doesn't work, nothing works but fastboot/rescue mode.
Maybe you can show the steps with screen shots or someone can translate you native language to English...I don't understand a lot of what you are saying.
I really appreciate your help.
Thank you.
fooshack said:
I'm sorry but I don't understand what you are saying. It obviously doesn't work, nothing works but fastboot/rescue mode.
Maybe you can show the steps with screen shots or someone can translate you native language to English...I don't understand a lot of what you are saying.
I really appreciate your help.
Thank you.
Click to expand...
Click to collapse
First of all, extract update.app your last firmware on your phone. Then download it.
https://mega.nz/#!BhgTyCZb!oUvS6UDhcsp54xCy5x8kvldPgBC43XHH5yGSWRdQF3w
This software is running fastboot/resuce menu. And it will write the rom on your phone.
Required for writting rom in your update.app, you extract update.app and copy System.img, Boot.img, Cust.img, Userdata.img, Cache.img.
You understand, i am foreign person. Sorry my bad english
İf you want to look for using programme page.
http://turkpda.com/konu/huawei-ascend-mate-7-rom-yuekleyici.954/
Huawei Mate 7 TL10 Cihazimdan Yollamişam
didn't work
Hey ladies and gentlemen,
I am having a serious problem. I tried to root my Honor 6 (H60-L04). After installing Super User via TWRP my smartphone started a bootloop. After I waited a few hours it turned off and I tried to reload it for booting into the download mode (to flash a new firmware via Honor MultiTool). But it still showed me that there is an empty battery and didn't start. How can I unbrick it?
Thanks
Haeggis said:
Hey ladies and gentlemen,
I am having a serious problem. I tried to root my Honor 6 (H60-L04). After installing Super User via TWRP my smartphone started a bootloop. After I waited a few hours it turned off and I tried to reload it for booting into the download mode (to flash a new firmware via Honor MultiTool). But it still showed me that there is an empty battery and didn't start. How can I unbrick it?
Thanks
Click to expand...
Click to collapse
do u have solution for this??
To install a full stock firmware follow these steps, if the phone is not booting in bootloader mode try doing this: After a loop gets complete, quickly press Vol UP button and connect the phone to PC, you'll be in bootloader mode.
Download your latest firmware and extract system.img, boot.img, recovery.img, cust.img from UPDATE.APP using Huawei Update Extractor tool.
Flash recovery first, using this command.
Code:
fastboot flash recovery recovery.img
Flash all other extracted files similarly firing these commands.
Code:
fastboot flash boot boot.img
fastboot flash cust cust.img
fastboot flash system system.img
After doing this put that very UPDATE.APP from which you extracted the files in dload folder of your external SDCARD.
Switch off your phone, and press Vol UP + Vol DOWN + Power button simultaneously.
Your device will now get to the full stock firmware.
I had a similar problem with mine when updating to EMUI 4. What I did was:
- Hold Volume Down while rebooting and Connect USB. It should boot into Bootload mode.
- If you get the Error Screen, reboot the Phone.
- If it doesn't work, hold all three buttons. It should reset the phone.
This actually reset my phone and made it work again. Don't ask me why or how.
You should Unbrick with Honor Multitool. You get to still have your data intact when you do only the first step without the 3 button install. If you don't have a TWRP backup that is. Don't ever install SU or root from TWRP. Use KingRoot or Multitool
CplBasti said:
I had a similar problem with mine when updating to EMUI 4. What I did was:
- Hold Volume Down while rebooting and Connect USB. It should boot into Bootload mode.
- If you get the Error Screen, reboot the Phone.
- If it doesn't work, hold all three buttons. It should reset the phone.
This actually reset my phone and made it work again. Don't ask me why or how.
Click to expand...
Click to collapse
If the device is rooted then you'll get install failed when doing three button reset, hence the manual flashing is needed.
The three button reset also fails, if in anyway your system is modified.
DigiGoon said:
If the device is rooted then you'll get install failed when doing three button reset, hence the manual flashing is needed.
The three button reset also fails, if in anyway your system is modified.
Click to expand...
Click to collapse
Well, my system was modified, and after doing that Three-Button reset twice, it actually worked.
Don't ask me why, it just worked. And I'm actually glad it did haha.
CplBasti said:
Well, my system was modified, and after doing that Three-Button reset twice, it actually worked.
Don't ask me why, it just worked. And I'm actually glad it did haha.
Click to expand...
Click to collapse
Good for you then, maybe the UPDATE.APP adjusted itself.
DigiGoon said:
Good for you then, maybe the UPDATE.APP adjusted itself.
Click to expand...
Click to collapse
Haha, yeah, probably
I'm just happy that my phone is working now.
Yes, sometimes Android does things which we can't understand(or maybe we don't have enough knowledge), so its easy to just accept the outcome and enjoy..!!
Hi,
I was trying to flash TWRP, but now I am stuck with flashing TWRP logo after rebooting or powering the phone on.
I am unable to get to the fastboot.
STEPS I did before brick:
1. unlocked OEM via official way
2. flashed TWRP
3. after that my phone was reset however most of the apps was missing, I was trying to do factory reset once again but it failed with the message "Data partition was heavily damaged"
4. I re-locked EOM
5. brick as mentioned above
Please help, I have the phone only two weeks and I have no idea how to fix this without fastboot.
Thank you.
Meiton said:
Hi,
I was trying to flash TWRP, but now I am stuck with flashing TWRP logo after rebooting or powering the phone on.
I am unable to get to the fastboot.
STEPS I did before brick:
1. unlocked OEM via official way
2. flashed TWRP
3. after that my phone was reset however most of the apps was missing, I was trying to do factory reset once again but it failed with the message "Data partition was heavily damaged"
4. I re-locked EOM
5. brick as mentioned above
Please help, I have the phone only two weeks and I have no idea how to fix this without fastboot.
Thank you.
Click to expand...
Click to collapse
Sounds like you flashed the 3030 version of TWRP. Download the 3020 version and put it in your fastboot folder. Plug in the USB to PC
Hold power and volume up untill the phone reboots. While it's still off immediately change to power and volume down and hold till it goes into fastboot (bootloader)
Now fastboot flash recovery TWRP.img
With the 3020 version.
Unplug the USB and hold power and volume up until it says the phone is booting.. let go and TWRP will load.
Go to Wipe / format data / type yes
Reboot to system and your all set
Sent from my Nexus 6P using Tapatalk
clsA said:
Sounds like you flashed the 3030 version of TWRP. Download the 3020 version and put it in your fastboot folder. Plug in the USB to PC
Hold power and volume up untill the phone reboots. While it's still off immediately change to power and volume down and hold till it goes into fastboot (bootloader)
Now fastboot flash recovery TWRP.img
With the 3020 version.
Unplug the USB and hold power and volume up until it says the phone is booting.. let go and TWRP will load.
Go to Wipe / format data / type yes
Reboot to system and your all set
Sent from my Nexus 6P using Tapatalk
Click to expand...
Click to collapse
So I've tried that but the phone is still booting to recovery (flashing TWRP logo) no matter what.
Basically the phone is always on now because if hold the power button (or any other combination) for a few second it will just reboot back.
I have an access only to ADB, but I am not able to boot to bootloader at all, it seems the bootloader is damaged somehow.
Also that warning about unlocked OEM doesn't have that text saying "hold volume up to boot to recovery" etc. like before brick.
Hi there,
Try using the Huawei Multi Tool with the Unbrick option : https://forum.xda-developers.com/honor-8/development/tool-huawei-multi-tool-team-mt-t3523923
Speaking from experience, this little fellow helped me recover my phone when I bricked it ON DAY ONE after failed root attempt... (Derp)
Let me know if it helped you
(Leave a thanks if it did )
EDIT : This tool is also useful if you want to get lazy whilst rooting. I use it constantly when flashing diffrent bits and pieces
Clearly follow My steps To unbrick and get normal device ::
Step 1 ::
Download the full firmware of your device.
Step 2 :
make sure that your bootloader is in unlocking state
Follow the video blindly ::: https://youtu.be/OMKDnBqbi3U?list=PL...eT9J26lkefvVkK
don't panic of mobile.
Step 3 :: done ..enjoy u did it
--------------------------------------------------------------------------
If you bricked on nougat then follow the below steps
step one :::
download the downgrade package to mm .
then extract the zip and open the update.app using HuaweiUpdateextrator in that select recovery and extract
1.now, boot your device into fastboot and flash the recovery (Optional)(try this if it said incompatible version on recovery)
2. on your sd card and make a folder "dload" . and copy the update.app which we have extracted earlier
3.the switch off the device and press all three buttons you will be reboot into recovery and done . you device will be okey
Meiton said:
So I've tried that but the phone is still booting to recovery (flashing TWRP logo) no matter what.
Basically the phone is always on now because if hold the power button (or any other combination) for a few second it will just reboot back.
I have an access only to ADB, but I am not able to boot to bootloader at all, it seems the bootloader is damaged somehow.
Also that warning about unlocked OEM doesn't have that text saying "hold volume up to boot to recovery" etc. like before brick.
Click to expand...
Click to collapse
Booting to the bootloader is just a timing issue
Phone must be hooked to PC with USB
And volume up and power till it goes black
Then immediately volume down and power and Hold untill the bootloader loads
Keep trying until you get it
Sent from my Nexus 6P using Tapatalk
clsA said:
Booting to the bootloader is just a timing issue
Phone must be hooked to PC with USB
And volume up and power till it goes black
Then immediately volume down and power and Hold untill the bootloader loads
Keep trying until you get it
Sent from my Nexus 6P using Tapatalk
Click to expand...
Click to collapse
I appreciate your help but I've tried it multiple times always with the same result.
I also can use "adb reboot bootloader", but it will reboot again to stuck recovery.
DJ Daemonix said:
Hi there,
Try using the Huawei Multi Tool with the Unbrick option : https://forum.xda-developers.com/honor-8/development/tool-huawei-multi-tool-team-mt-t3523923
Speaking from experience, this little fellow helped me recover my phone when I bricked it ON DAY ONE after failed root attempt... (Derp)
Let me know if it helped you
(Leave a thanks if it did )
EDIT : This tool is also useful if you want to get lazy whilst rooting. I use it constantly when flashing diffrent bits and pieces
Click to expand...
Click to collapse
I've tried that, but I am still stuck as that tool is using fastboot as every other tool to flash .img files.
Thank you for the tip though.
Plug phone into computer with USB, then hold down power + volume down until it eventually boots into bootloader. I had the same scenario as you and that's how I got into the bootloader. You can flash either a good TWRP or the stock recovery, either one will work.
Hello there,
i had an camera issue on my Honor 6x (EMUI 5 B369), thats why I made a Rollback to EMUI 4(B130). After doing that properly with that files:
http://download-c.huawei.com/download/downloadCenter?downloadId=94070&version=376169&siteCode=de-h From Bxxx to B300 (only contains some .img (See Attachment))
and http://download-c.huawei.com/download/downloadCenter?downloadId=94087&version=376224&siteCode=de-h From B300 to B130 (full Update.app)
After being on EMUI 4, I wanted to dload back to B369, but then I accidentally flashed the B300, which only contained some .img.
Then it went into softbrick mode, so I only was able to boot into fastboot.
To flash anything I unlocked the bootloader. The Device turned off and back on, then wanted to boot to recovery for hard reset.
This is where I am now. I can not boot into any mode. It just turns on and then shows the "Your device has been unlocked and cant be trusted". I tried to go into dload mode, tried recovery, tried fastboot, none of them were working.
When force rebooting it just turns on, vibrates 2 times and shows that "Your device..." screen and "Your device is booting now"
To archieve that it forgets that process to boot into recovery i let the battery drain empty and try again, which partly worked. Now sometimes it doesnt show "Your device is booting now" on the "Your device..." screen, but it shows the three options that are normally shown when turning on with opened bootloader.
But still no success into fastboot etc.
Edit: My phone seems to be not charging anymore, because ist shows that booting stuff, but then turns on and shows the "Your device..."-screen
Is there any way to unbrick my Honor 6X BLN-L21C432?
Greetings, LRX
PS: plss help me
I didn't understood a thing; actually, you have access to fastboot mode or not? And if yes, what's the status of FRP and Phone in fastboot... Lock or unlocked?
Try to go in fastboot mode by pressing the volume down + power on buttons while your phone is connected to a PC USB port. If this shouldn't work, i had read something online that says that there is a chance to flash an image through HiSuite; never tested, so i can't ensure that it'll works... But we'll try to find out a way to unbrick your device
:crying: same problem shows on my mobile if you found any solution please share with me my device also in same state
same here ... my BLN-L21 is bricked. Can't access to recovery, no fastboot, no e-recovery. any connection with PC !
I have disassembled the phone and looking for schematic testpoint but no result for now
---------- Post added at 10:44 AM ---------- Previous post was at 10:41 AM ----------
LRX22G said:
Hello there,
i had an camera issue on my Honor 6x (EMUI 5 B369), thats why I made a Rollback to EMUI 4(B130). After doing that properly with that files:
http://download-c.huawei.com/download/downloadCenter?downloadId=94070&version=376169&siteCode=de-h From Bxxx to B300 (only contains some .img (See Attachment))
and http://download-c.huawei.com/download/downloadCenter?downloadId=94087&version=376224&siteCode=de-h From B300 to B130 (full Update.app)
After being on EMUI 4, I wanted to dload back to B369, but then I accidentally flashed the B300, which only contained some .img.
Then it went into softbrick mode, so I only was able to boot into fastboot.
To flash anything I unlocked the bootloader. The Device turned off and back on, then wanted to boot to recovery for hard reset.
This is where I am now. I can not boot into any mode. It just turns on and then shows the "Your device has been unlocked and cant be trusted". I tried to go into dload mode, tried recovery, tried fastboot, none of them were working.
When force rebooting it just turns on, vibrates 2 times and shows that "Your device..." screen and "Your device is booting now"
To archieve that it forgets that process to boot into recovery i let the battery drain empty and try again, which partly worked. Now sometimes it doesnt show "Your device is booting now" on the "Your device..." screen, but it shows the three options that are normally shown when turning on with opened bootloader.
But still no success into fastboot etc.
Edit: My phone seems to be not charging anymore, because ist shows that booting stuff, but then turns on and shows the "Your device..."-screen
Is there any way to unbrick my Honor 6X BLN-L21C432?
Greetings, LRX
PS: plss help me
Click to expand...
Click to collapse
Do yo have the red light ? and red charging logo before boot ? I have charge my battery yesterday out of phone (to see if out of battery change boot option). And try boot fastboot / recovery / erecovery with plug and replug battery but no success. Still same
Try to boot into fastboot mode. If you disconnected phone battery, connect it again. Unplug the phone from USB cable. When powered off, hold Vol down key (and only hold that key), then plug your phone to your computer (be sure to hold Vol down until you reach fastboot screen).
If you reached fastboot mode, then flash the RECOVERY.img image from B130 to the recovery partition.
If successful, unplug your device, then reboot.
When rebooting, hold Vol Up and Power button until you see the boot warning saying that you're booting to recovery mode or something like that (the screen won't show any other options to boot as a regular boot should, so that will be an important indicator).
If you reach the recovery screen, then try to dload full B130 firmware.
If this fail, try another flashing combinations. I mean:
1- Try dloading another firmware (e.g. the B369 firmware you downloaded) over B130 recovery.
2- If step 1 failed, flash B369 RECOVERY.img, then try to dload B130 package. If this don't work, now try to dload B369.
3- If previous steps failed, try to flash RECOVERY.img from THE DOWNGRADING PACKAGE (the one with few IMGs). After that, dload B130.
If this don't work, is because your soft brick is a real pain in the ass.
Cheers, and good luck.
PS: don't miss your hope. I achieved to recover my bricked phone with FRP locked (FRP doesn't let you flash anything at all), and a warning screen with RED letters, and a big exclamation mark, saying that the phone was not able to boot.
try dloading the correct firmware.dload works most of the time.
there is no way to enter in dload, recovery or fastboot. i try all methods but no luck. please is here any one know that can we access flash IC?
Ounly one possibility is using "testpoint" on motherboard mobile (Huawei USB COM 1.0 port in PC) with DC Phoenix and than HCU (19€). I had the same problem , I have repared it
1. Unbrick tutorial: you can find it on webside dc-unlocker ((ALL new users prevented from posting outside links in their messages)
2. Repair oeminfo and custom.bin tutorial: you can find it on webside hcu-client (ALL new users prevented from posting outside links in their messages)
I have the picture Testpoint Honor 6x BLN-L21.jpg
Send mi private message.
Good luck...
power off the device hold the vol down connect data cable to pc it will show fastboot then flash twrp then reboot to twrp flash custom rom.
Impossible to reboot to TWRP from fastboot...
- Install russian MultiTool 8
- download rollback package (Android 6, EMUI 4.1, 1.76GB ) then extract dload folder into SD Card and put sd-card in phone
- Connect USB cable to PC, power off phone, keep pressed Vol- then plug USB cable, phone start in Fastboot Mode
- From MultiTool flash Recovery and eRecovery 1.x version
- Power off phone
- Reboot pressing Vol+,Vol-, Power and wait...