I have a samsung Galaxy S6 SM-G920F.
Got some problems with the firmware ( got it from Sammobile).
After successfully flashing my phone using Odin3 , the device reboot, everything is ok.
Android is launched, then the device is sticked , turned off and restart with loop reboot.
Solution ?
Thanks
make factory reset and wipe cash
shiko2007 said:
make factory reset and wipe cash
Click to expand...
Click to collapse
i did it, and it is sticked on the logo screen : (samsung galaxy S6)
ok bro , make soft reset by hold (vol. down + hold power ) and when you see samsung s6 powered by android hold only(vol.down)
shiko2007 said:
ok bro , make soft reset by hold (vol. down + hold power ) and when you see samsung s6 powered by android hold only(vol.down)
Click to expand...
Click to collapse
It stick in Samsung Logo :/
walidKr said:
It stick in Samsung Logo :/
Click to expand...
Click to collapse
ok , try flashed again the firmware and after that enter to recovery and make factory reset and wipe cash and reboot
usually the device may be take 10 minute to boot up , if it's stuck on bootloop make soft reset to reboot and wait 10 min again .
shiko2007 said:
ok , try flashed again the firmware and after that enter to recovery and make factory reset and wipe cash and reboot
usually the device may be take 10 minute to boot up , if it's stuck on bootloop make soft reset to reboot and wait 10 min again .
Click to expand...
Click to collapse
android start but, it freeze and stuck after few seconds
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
bro, can you tell me "PDA" of the firmware & Security Patch Level you are downloaded ?
also, can you post the new log of odin for the new firmware you downloaded ?
shiko2007 said:
bro, can you tell me "PDA" of the firmware & Security Patch Level you are downloaded ?
also, can you post the new log of odin for the new firmware you downloaded ?
Click to expand...
Click to collapse
name of PDA: G920FXXU5EQAC_G920FOXA5EQAC_G920FXXU5EQAC_HOME.tar.md5
(downloaded from Sammobile : firmware of G920F)
i didn't put a Security Patch level
log of odin :
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin engine v(ID:3.1101)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sboot.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> cm.bin
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img
<ID:0/003> cache.img
<ID:0/003> hidden.img
<ID:0/003> modem.bin
<ID:0/003> RQT_CLOSE !!
<ID:0/003> RES OK !!
<ID:0/003> Removed!!
<ID:0/003> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
mmmm , i don't know bro it's strange , it should passes Samsung logo without any problem , ok , try flashing again with latest odin version , also is this the orignal csc of your device or you are change it ? if this original csc you can use smart switch to solve your problem by using emergency recovery ?
are your device have root ? or not
your firmware you want to flash is nougat , try flashing the latest 6.0.1 and it should work and after that if you want nougat update to it from latest 6.0.1
shiko2007 said:
mmmm , i don't know bro it's strange , it should passes Samsung logo without any problem , ok , try flashing again with latest odin version , also is this the orignal csc of your device or you are change it ? if this original csc you can use smart switch to solve your problem by using emergency recovery ?
are your device have root ? or not
Click to expand...
Click to collapse
not rooted.
sometimes the device start and android is launched but stuck after few seconds .
do you think there is a probleme with recovery ?
walidKr said:
not rooted.
do you think there is a probleme with recovery ?
Click to expand...
Click to collapse
are you can access to recovery ? if yes . so no problem with it
shiko2007 said:
are you can access to recovery ? if yes . so no problem with it
Click to expand...
Click to collapse
even in recovery it stucks after few seconds
ok bro, don't worry , your device will work again , your firmware you want to flash is nougat , try flashing the latest 6.0.1 and it should work and after that if you want nougat update to it from latest 6.0.1
shiko2007 said:
ok bro, don't worry , your device will work again , your firmware you want to flash is nougat , try flashing the latest 6.0.1 and it should work and after that if you want nougat update to it from latest 6.0.1
Click to expand...
Click to collapse
steps plz
walidKr said:
steps plz
Click to expand...
Click to collapse
1-download latest firmware of 6.0.1 of your country/ carrier that have Security Patch Level ""2017-01-01""
2-before flashing firmware make factory reset and wipe cash
3-reboot your device to download mode and flash firmware
4-after flash firmware ,and when your device reboot . enter to recovery quickly and make factory reset and wipe cash
5-reboot and it should work
---------- Post added at 02:50 AM ---------- Previous post was at 02:48 AM ----------
you can try now using smart switch and enter to emergency recovery and put your device in download mode and see if it will solve your problem
shiko2007 said:
1-download latest firmware of 6.0.1 of your country/ carrier that have Security Patch Level ""2017-01-01""
2-before flashing firmware make factory reset and wipe cash
3-reboot your device to download mode and flash firmware
4-after flash firmware ,and when your device reboot . enter to recovery quickly and make factory reset and wipe cash
5-reboot and it should work
---------- Post added at 02:50 AM ---------- Previous post was at 02:48 AM ----------
you can try now using smart switch and enter to emergency recovery and put your device in download mode and see if it will solve your problem
Click to expand...
Click to collapse
where can i find this firmware with this security patch level ?
walidKr said:
where can i find this firmware with this security patch level ?
Click to expand...
Click to collapse
use sammobile
shiko2007 said:
use sammobile
Click to expand...
Click to collapse
and the security patch level ?? i can't see it on sammobile
walidKr said:
and the security patch level ?? i can't see it on sammobile
Click to expand...
Click to collapse
you will see it , if you choose your firmware that have PDA like that G920FXXU5DQA7
Related
My friend tried to unlock vibrant 4G, but he used pit 512 file for vibrant. And then he flashed it ( re-partition ). Now, my phone always freeze at bootloader, I can mod to download section, but it freeze at the last step of reformat ROM ( <ID:0/005> Re-Partition operation failed. or Write failed) . What should I do now ?
Hello. A few days ago I tried to root my Samsung Galaxy S2 Plus but I failed. I installed Odin (all versions) but when I select the PDA button and select the "Jerry_recovery.tar.md5" I recive an error :
Code:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> MD5 hash value is invalid
<OSM> Jerry_recovery.tar.md5 is invalid.
<OSM> End...
I searched on internet and I found a solution : To rename Jerry_recovery.tar.md5 in Jerry_recovery.tar . If I try this , Odin didn't give me any error but I did that for nothing... You will see later why.
After that I boot my phone in CWM mode and I tried to install SuperUser but again I recived another error :
Code:
E: failed to verify whole-file signature
E: signature verification failed
...or something like that and then my phone restarts.
I need some help guys. Please give me a solution and if you need more informations about my phone , just ask me.
Lascu Vladut said:
After that I boot my phone in CWM mode and I tried to install SuperUser but again I recived another error :
Code:
E: failed to verify whole-file signature
E: signature verification failed
...or something like that and then my phone restarts.
I need some help guys. Please give me a solution and if you need more informations about my phone , just ask me.
Click to expand...
Click to collapse
Phone restores the stock recovery everytime you boot, untill you boot into CWM at least once. You correctly flashed CWM recovery, but then phone rebootes and restores the stock one. Uncheck "Auto Reboot" in Odin, flash it again and boot into recovery from the Odin Mode screen. Then you can install SuperSU.
Lascu Vladut said:
Hello. A few days ago I tried to root my Samsung Galaxy S2 Plus but I failed. I installed Odin (all versions) but when I select the PDA button and select the "Jerry_recovery.tar.md5" I recive an error :
Code:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> MD5 hash value is invalid
<OSM> Jerry_recovery.tar.md5 is invalid.
<OSM> End...
I searched on internet and I found a solution : To rename Jerry_recovery.tar.md5 in Jerry_recovery.tar . If I try this , Odin didn't give me any error but I did that for nothing... You will see later why.
After that I boot my phone in CWM mode and I tried to install SuperUser but again I recived another error :
Code:
E: failed to verify whole-file signature
E: signature verification failed
...or something like that and then my phone restarts.
I need some help guys. Please give me a solution and if you need more informations about my phone , just ask me.
Click to expand...
Click to collapse
Try TWRP it has option to ignore signature verification
Sent from my GT-I9082 using Tapatalk
black87 said:
Try TWRP it has option to ignore signature verification
Sent from my GT-I9082 using Tapatalk
Click to expand...
Click to collapse
CWM ignores signature verification by default.
andrewww57 said:
Phone restores the stock recovery everytime you boot, untill you boot into CWM at least once. You correctly flashed CWM recovery, but then phone rebootes and restores the stock one. Uncheck "Auto Reboot" in Odin, flash it again and boot into recovery from the Odin Mode screen. Then you can install SuperSU.
Click to expand...
Click to collapse
Are you sure about that ? When I try to boot CWM from Odin Mode screen my phone just boot normaly...
black87 said:
Try TWRP it has option to ignore signature verification
Sent from my GT-I9082 using Tapatalk
Click to expand...
Click to collapse
What is TWRP ? What is he doing ? And how to use it ? Can you give me a link with a tutorial ? Or you can explain me here...
Lascu Vladut said:
Are you sure about that ? When I try to boot CWM from Odin Mode screen my phone just boot normaly...
Click to expand...
Click to collapse
Yes. I hold "Vol+"+"Home"+"Power" on Odin Mode screen after flashing and keep them holding until Samsung Galaxy S II Plus logo appears. Then I get into recovery.
You didn't even flash cwm, you need to remove the .md5 from the name and flash again
CoolDevelopment said:
You didn't even flash cwm, you need to remove the .md5 from the name and flash again
Click to expand...
Click to collapse
If you read everything you see I did that.
andrewww57 said:
Yes. I hold "Vol+"+"Home"+"Power" on Odin Mode screen after flashing and keep them holding until Samsung Galaxy S II Plus logo appears. Then I get into recovery.
Click to expand...
Click to collapse
I DID IT ! Thank you man , I DIT IT ! In the end my phone is rooted.
Thank you for everyone who post here. Job done.
Lascu Vladut said:
If you read everything you see I did that.
I DID IT ! Thank you man , I DIT IT ! In the end my phone is rooted.
Thank you for everyone who post here. Job done.
Click to expand...
Click to collapse
Hi! Sorry for the question but I got the same problem of you. Where can I find the zip of superuser? I can't find it anywhere.
Thank you
do not reboot just remove the battery after installation of cwm. apply the battery back and.then boot .should be ok.
install su by using the new recovery app
that was my way..
---------- Post added at 11:26 PM ---------- Previous post was at 11:22 PM ----------
Emi1888 said:
Hi! Sorry for the question but I got the same problem of you. Where can I find the zip of superuser? I can't find it anywhere.
Thank you
Click to expand...
Click to collapse
use google
Emi1888 said:
Hi! Sorry for the question but I got the same problem of you. Where can I find the zip of superuser? I can't find it anywhere.
Thank you
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?t=2303395
There's a link there.
@silvano2 Yep. Also a good ideea to remove the battery.
..
I will try and report here later.
Thanks
Enviado do meu GT-I9500
Found the same guide in other blog. It works fine..
..
Ap0rd said:
It may be the same method, but it's not the same way to say it.
Click to expand...
Click to collapse
U serious?
robertostorm said:
U serious?
Click to expand...
Click to collapse
..
By by knox, you should warning people about knox
Enviado do meu GT-I9505 através de Tapatalk
..
You said may lol, that's why I prevent you. Because not all users do the previous research
Enviado do meu GT-I9505 através de Tapatalk
no SU binary
Hi
I followed your instructions. I"m running i9500ubufna2 Android 4.4.2 S4 I9500 from Sammobile . I flashed Philz Recovery, no problem. I went to Philz settings and clicked on Reroot device.
when i open SuperSU , it says "No SU Binary installed, and SUperSU cannot install it. This is a problem"
what do i do now?
Andre
andreapaid said:
Hi
I followed your instructions. I"m running i9500ubufna2 Android 4.4.2 S4 I9500 from Sammobile . I flashed Philz Recovery, no problem. I went to Philz settings and clicked on Reroot device.
when i open SuperSU , it says "No SU Binary installed, and SUperSU cannot install it. This is a problem"
what do i do now?
Andre
Click to expand...
Click to collapse
Install CFRoot.
Put you phone into Dowload Mode, and flash using Odin.
Enviado do meu GT-I9500
Yes that worked thanks
QUOTE=eric-filth;50878054]Install CFRoot.
Put you phone into Dowload Mode, and flash using Odin.
Enviado do meu GT-I9500[/QUOTE]
Anyone know if this works for AT&T 4.4?
Hi!
I tried that, but a dead Android appears, with "error" and it doesn't enter the philz recovery. It boots normally though. Does anyone know what went wrong?
Tks!
Sent from my GT-I9500 using xda app-developers app
problem
Hi!
I tried that, but a dead Android appears, with "error" and it doesn't enter the philz recovery. It boots normally though. Does anyone know what went wrong?
Ap0rd said:
How to root Galaxy S4 GT-9500 running Android 4.4.2 (KitKat)
Proceed at your own risk, rooting your device may void your warranty and Knox will no longer function
Requirements:
Samsung Galaxy S4 GT-9500 running Android 4.4.2
Kies disabled
Odin 3.09: http://forum.xda-developers.com/gal...08-2013-odin-3-09-odin-1-85-versions-t2189539
PhilZ Touch 6 Recovery by Phil3759: http://forum.xda-developers.com/showthread.php?t=2201860 (download the .tar.md5 version for the GT-9500)
Make sure that USB debugging is enabled in developer options
Recommended:
Backup your data
Battery charged more than 50%
Rooting your device:
Connect your device to your computer (ID:COM in odin should be highlighted in blue)
Select Philz touch recovery 6 as AP in odin, make sure F.Reset Time and F.Reboot are checked (Do NOT check any other options)
Press the start button
Wait for Odin to finish
Power-off your device and boot into recovery by holding these buttons: Volume up+Home+Power
If Philz recovery doesn't appear, it may take a few tries.
Now enter philz settings and select reroot device.
When your device boots, download SuperSU (by Chainfire) in the play store.
Download Root Checker Basic and Verify your Root.
Done!
Click to expand...
Click to collapse
"KNOX" appears in my settings menu (I have just updated to 4.4.2 today) however, when I select it from the menu there is a message that reads "you need to download and install this app" so that must mean that knox is not yet actually on my s4 at all ?
can you tell me, what is KIES how do you disable it ?
anyone know how to reset avoid knox?
is this ok to use to root my i9500 on 4.4.2 with a mac osx ?
dottech.org/149375/how-to-root-samsung-galaxy-s4-on-android-4-4-2-kitkat-gt-i9500-gt-i9505-guide/
s4 stuck on odin mode in half way
i hv s4 i9500 running on 4.4.2 i tried to root it but it is stuck on odin mode with half progress bar... i tried to use different odin but it still stuck on the same place... and i cant get a normal boot now.... my odin extension are this... please help...
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CF-Auto-Root-jflte-jfltexx-gti9505.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> recovery.img
<ID:0/003> NAND Write Start!!
<ID:0/003> cache.img.ext4 <---- IT STUCK AT THIS POINT EVERY TIME
Excellent post
Hello.
After using rom manager the phone wont boot. The only thing that works is the upload mode. I allready downloaded the usb drivers an de odin software, after searching on the internet, but i can't find the files to use with the odin to restore the phone. Does any body knows where can i downlod then.
Thanks.
juancho71 said:
Hello.
After using rom manager the phone wont boot. The only thing that works is the upload mode. I allready downloaded the usb drivers an de odin software, after searching on the internet, but i can't find the files to use with the odin to restore the phone. Does any body knows where can i downlod then.
Thanks.
Click to expand...
Click to collapse
There are 2 ways to install a new rom to your device. Through recovery (ex. CWM) or wth a flasher. Odin is the Samsung flasher and you need a rom image to flash it over your phone. You will lose all your both ways.
I was not able to find in any image of your phone online in order you can flash it with Odin BUT you can install a recovery with Odin and then flash a rom.zip from the recovery...
I found these tutorials that will help you:
How to Install Custom Recovery on the Samsung Galaxy Prevail 2
How to Install a Custom ROM on the Samsung Galaxy Prevail 2
Good luck!
recovery fail
Thanks for taking the time to answer.
I downloaded the recovery and the odin 1.85, but after i clicki start, this is what i get:
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<OSM> All threads completed. (succeed 0 / failed 1)
MY CELL IS A SAMSUNG GALAXY S6 MODEL SM-G920i, AND IT'S IN THE INFINITE LOOP AND I CAN NOT ACCESS THE RECOVERY MODE AND EVERY TIME I TRY TO INSTALL THE ORIGINAL ROM BY THE ODIN OF THAT ERROR: <ID: 0/004> Added! !
<ID: 0/004> Odin engine v (ID: 3.1203) ..
<ID: 0/004> File analysis ..
<ID: 0/004> SetupConnection ..
<ID: 0/004> Complete (Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
JA GET INSTALLING THE TWR MORE I CAN NOT ACHIEVE MORE BECAUSE OF THAT ERROR: RECOVERY IS NOT SEANDROID ENFORCING, WHEN I RESTART THE APPLIANCE AND LET IT START NORMAL THE ERROR SOME. I DO NOT KNOW WHAT TO DO, HELP ME PLEASE.
Galaxy S6 bootloop
C3RB3RU5X said:
MY CELL IS A SAMSUNG GALAXY S6 MODEL SM-G920i, AND IT'S IN THE INFINITE LOOP AND I CAN NOT ACCESS THE RECOVERY MODE AND EVERY TIME I TRY TO INSTALL THE ORIGINAL ROM BY THE ODIN OF THAT ERROR: <ID: 0/004> Added! !
<ID: 0/004> Odin engine v (ID: 3.1203) ..
<ID: 0/004> File analysis ..
<ID: 0/004> SetupConnection ..
<ID: 0/004> Complete (Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
JA GET INSTALLING THE TWR MORE I CAN NOT ACHIEVE MORE BECAUSE OF THAT ERROR: RECOVERY IS NOT SEANDROID ENFORCING, WHEN I RESTART THE APPLIANCE AND LET IT START NORMAL THE ERROR SOME. I DO NOT KNOW WHAT TO DO, HELP ME PLEASE.
Click to expand...
Click to collapse
Hi C3RB3RU5X,
I had the same problem. Whenever I tried to flash the Stock ROM things got worse, until in the end I had the same problem as you.
If you can still access download mode try the following:
download the latest TWRP file for your S6 model
download AOKP image for your S6 model
download GAPPS for your S6 model
enter download mode
flash TWRP with Odin, but un-tick "Auto-Reboot" in Odin
when completed go to recovery at once (don't let the phone try to boot normally, just "kill" phone and hold the buttons for download mode)
when in recovery (TWRP) start ADB software (if you don't know how google samsung galaxy S6 ADB)
transfer the downloaded AOKP image and GAPPS to your phone (/sdcard is a nice place) via ADB
wipe cache in TWRP
install image and GAPPS
wipe cache and reboot your phone
everything should be normal by then
Good luck !
Peter
petrus_muc said:
Hi C3RB3RU5X,
I had the same problem. Whenever I tried to flash the Stock ROM things got worse, until in the end I had the same problem as you.
If you can still access download mode try the following:
download the latest TWRP file for your S6 model
download AOKP image for your S6 model
download GAPPS for your S6 model
enter download mode
flash TWRP with Odin, but un-tick "Auto-Reboot" in Odin
when completed go to recovery at once (don't let the phone try to boot normally, just "kill" phone and hold the buttons for download mode)
when in recovery (TWRP) start ADB software (if you don't know how google samsung galaxy S6 ADB)
transfer the downloaded AOKP image and GAPPS to your phone (/sdcard is a nice place) via ADB
wipe cache in TWRP
install image and GAPPS
wipe cache and reboot your phone
everything should be normal by then
Good luck !
Peter
Click to expand...
Click to collapse
I'm having problems downloading the AOKP image for your S6 model
C3RB3RU5X said:
I'm having problems downloading the AOKP image for your S6 model
Click to expand...
Click to collapse
Did you look at
https://forum.xda-developers.com/galaxy-s6/orig-development/unofficial-aokp-7-1-1-t3550923
Just look for your model (SM-G920x)
petrus_muc said:
Did you look at
https://forum.xda-developers.com/galaxy-s6/orig-development/unofficial-aokp-7-1-1-t3550923
Just look for your model (SM-G920x)
Click to expand...
Click to collapse
has no download link, the link has been removed.
C3RB3RU5X said:
has no download link, the link has been removed.
Click to expand...
Click to collapse
As far as I know there is no specific ROM for the Samsung S6 (not like the stock ROM, e.g SM-G920I), only for Samsung S6 (SM-G920). So you could flash this one. Just inquire if your specific provider in India might have restrictions on unlocked phones.
Name of ROM is aokp_zerofltexx_nougat_unofficial_2018-02-17_1022.zip
Just google, there are a number of download links.
If you search the xda site you will find a page where the download links are listed.
petrus_muc said:
As far as I know there is no specific ROM for the Samsung S6 (not like the stock ROM, e.g SM-G920I), only for Samsung S6 (SM-G920). So you could flash this one. Just inquire if your specific provider in India might have restrictions on unlocked phones.
Name of ROM is aokp_zerofltexx_nougat_unofficial_2018-02-17_1022.zip
Just google, there are a number of download links.
If you search the xda site you will find a page where the download links are listed.
Click to expand...
Click to collapse
thank you she help, but I did not find this list you said, I sent an email to the AOKP facebook community and I'll see if they contact.
I found this topic will it work?
https://forum.xda-developers.com/ga...nt/g92xx-android-o-samsung-galaxy-s6-t3663901
C3RB3RU5X said:
I found this topic will it work?
https://forum.xda-developers.com/ga...nt/g92xx-android-o-samsung-galaxy-s6-t3663901
Click to expand...
Click to collapse
No idea, I didn't try.
But it tokk me 5 mins to find the relevant site (modify search terms !)
https://forum.xda-developers.com/ga...ent/7-1-2-unofficial-aokp-s6-s6-edge-t3746751
Thats where I downloaded the ROM from and it works perfectly till now.
I'm on bootloop too and can't get into TWRP. Did you solve this?
gborfitz said:
I'm on bootloop too and can't get into TWRP. Did you solve this?
Click to expand...
Click to collapse
not
C3RB3RU5X said:
not
Click to expand...
Click to collapse
Well... I can. It's tricky but works. Once you had flashed TWRP (with auto-reboot box unticked) press combination buttons to go to download mode. But here's the trick: Just when screen is off change combination to TWRP and boom...
Just don't let it boot into system before that.
Regards.
petrus_muc said:
Hi C3RB3RU5X,
I had the same problem. Whenever I tried to flash the Stock ROM things got worse, until in the end I had the same problem as you.
If you can still access download mode try the following:
download the latest TWRP file for your S6 model
download AOKP image for your S6 model
download GAPPS for your S6 model
enter download mode
flash TWRP with Odin, but un-tick "Auto-Reboot" in Odin
when completed go to recovery at once (don't let the phone try to boot normally, just "kill" phone and hold the buttons for download mode)
when in recovery (TWRP) start ADB software (if you don't know how google samsung galaxy S6 ADB)
transfer the downloaded AOKP image and GAPPS to your phone (/sdcard is a nice place) via ADB
wipe cache in TWRP
install image and GAPPS
wipe cache and reboot your phone
everything should be normal by then
Good luck !
Peter
Click to expand...
Click to collapse
MY FRIEND FRIEND I TRIED TO DO FOOTSTEPS, DOWNLOADS:
[*] TWRP file for your S6 model
[*] AOKP image for your S6 model
[*] GAPPS for your S6 model
SO THAT THE ERROR IS TIME TO INSTALL THE TWRP, THE ERROR AND THE SAME:
<ID: 0/006> Added !!
<ID: 0/006> Odin engine v (ID: 3.1203) ..
<ID: 0/006> File analysis ..
<ID: 0/006> SetupConnection ..
<ID: 0/006> Initialzation ..
<ID: 0/006> Get PIT for mapping ..
<ID: 0/006> Complete (Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
WITHOUT SPEAKING [FAIL!] THAT APPEARS IN ODIN.
IF YOU KNOW WHAT TO DO HELP ME OR PLEASE.
THE VERSION OF MY Odin3_v3.12.3.
OBSERVATION: TWRP AND RA BE INSTALLED ON BL OR AP?
petrus_muc said:
No idea, I didn't try.
But it tokk me 5 mins to find the relevant site (modify search terms !)
https://forum.xda-developers.com/ga...ent/7-1-2-unofficial-aokp-s6-s6-edge-t3746751
Thats where I downloaded the ROM from and it works perfectly till now.
Click to expand...
Click to collapse
WILL IT WORK ON THE SM-G920i MODEL?
C3RB3RU5X said:
WILL IT WORK ON THE SM-G920i MODEL?
Click to expand...
Click to collapse
It seems you don't like to read instructions !
Otherwise you would have found out by yourself that you have to add the TWRP-3.2.1.0xxx.img.tar to AP !
If you want to be 100% sure that the AOKP image works on your phone model you will have to inquire more deeply.
I can't say for sure.
Dear fellow, I am able to solve the infinite loop error in my samsung s6, installing the original but modified ROM. I am grateful to all who have helped me.
but he still has two errors one is IMEI the 350000000000006/01.
and the other is in recovery, at the end of the recovery mode screen a message appears:
Suported API: 3
# MANUAL MODE #
- Appling Multi-CSC ...
Applied the CSC-code: TTT
Successfully applied multi-CSC.
if anyone can solve this error I will be grateful still.