help - Galaxy S6 Q&A, Help & Troubleshooting

Phone : Samsung Galaxy S6 Edge +
Model Name : SM-G928C
Phone Country : United Arab Emirates
Product Code : XSG
PDA : QA5
What happened? : my mother always turning off the phone if she's not using it so there's a running update on this phone then she turn off the phone while updating (note she's not techy so she didnt know what she was doing) so thats why.
(this phone is not rooted)
What i do : the first i tried to fix this phone is download any firmware that i see in sammobile on g928c then my phone turn to blue screen and a message "an error has occurred while updating the device software use the emergency recovery function in the smart switch pc software", Then i tried the smart switch i press MORE>EMERGENCY SOFTWARE RECOVERY AND INSTALLATION>DEVICE INITIALIZATION> i entered model name and my s/n number then > ok > set up my phone in to download mode then click okay and wait to finish the installation then after that my phone back to samsung logo boot loop now i tried to install the main firmware i see in smartswitch
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
i downloaded it in sammobile and used it in odin but the results is the same bootloop on samsung logo and i tried odin v3.09, odin3_v3.10.6, odin3_v3.10.7 and the latest 12.3 its just the same issue (note: i tried samsung kies too but its just the same on smartswitch)
Main Problem :
- Stuck on samsung logo / Boot loop on samsung logo
- can't enter to recovery mode
- FRP LOCK : On
any solution for this?

Read https://forum.xda-developers.com/showpost.php?p=71478246&postcount=3

dinamo1975 said:
Read https://forum.xda-developers.com/showpost.php?p=71478246&postcount=3
Click to expand...
Click to collapse
is it required the custom rom for me? its on the steps on the thread you gave

chibisan14 said:
is it required the custom rom for me? its on the steps on the thread you gave
Click to expand...
Click to collapse
If you have already installed the TRWP Recovery, yes you can install the custom ROM! Otherwise, you must flash the original / stock firmware.

dinamo1975 said:
If you have already installed the TRWP Recovery, yes you can install the custom ROM! Otherwise, you must flash the original / stock firmware.
Click to expand...
Click to collapse
i tried but the odin error, cant enter to settings to change the frp lock only download mode i can access
<ID:0/005> Added!!
<ID:0/005> Removed!!
<ID:0/005> Added!!
<ID:0/005> Odin engine v(ID:3.1203)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> recovery.img
<ID:0/005> RQT_CLOSE !!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)

chibisan14 said:
i tried but the odin error, cant enter to settings to change the frp lock only download mode i can access
<ID:0/005> Added!!
<ID:0/005> Removed!!
<ID:0/005> Added!!
<ID:0/005> Odin engine v(ID:3.1203)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> recovery.img
<ID:0/005> RQT_CLOSE !!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
thx to @forumber2
You must follow this procedure:
1. Download this program LINK
2. Extract it to a new folder and open it
3. Enter the parameters like attached picture (1) and wait to download the firmware
4. Extract the firmware (use winrar/winzip/ 7zip) in a new folder and you will have 4 files like attached picture (2)
5. Open Odin and put these 4 file accordingly in Odin (BL to BL, AP to AP, CP to CP, CSC to CSC) like attached picture (3) and flash them (press START).

is there any other link you provided to download that 2088 MB because its always interrupted and make me download it again from the start using samfirm

chibisan14 said:
is there any other link you provided to download that 2088 MB because its always interrupted and make me download it again from the start using samfirm
Click to expand...
Click to collapse
SamFirm program himself make the download!

dinamo1975 said:
If you have already installed the TRWP Recovery, yes you can install the custom ROM! Otherwise, you must flash the original / stock firmware.
Click to expand...
Click to collapse
dinamo1975 said:
thx to @forumber2
You must follow this procedure:
1. Download this program LINK
2. Extract it to a new folder and open it
3. Enter the parameters like attached picture (1) and wait to download the firmware
4. Extract the firmware (use winrar/winzip/ 7zip) in a new folder and you will have 4 files like attached picture (2)
5. Open Odin and put these 4 file accordingly in Odin (BL to BL, AP to AP, CP to CP, CSC to CSC) like attached picture (3) and flash them (press START).
Click to expand...
Click to collapse
dinamo1975 said:
SamFirm program inself make the download!
Click to expand...
Click to collapse
Checking CRC32...
Error: CRC does not match. Please redownload the file.
thats why i redownload it again and start to 1% but thanks trying to download it again

Checking CRC32...
Error: CRC does not match. Please redownload the file.
downloading again for the 4th time

chibisan14 said:
Checking CRC32...
Error: CRC does not match. Please redownload the file.
downloading again for the 4th time
Click to expand...
Click to collapse
Download from HERE

dinamo1975 said:
Download from HERE
Click to expand...
Click to collapse
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin engine v(ID:3.1203)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> sboot.bin
<ID:0/005> param.bin
<ID:0/005> cm.bin
<ID:0/005> boot.img
<ID:0/005> recovery.img
<ID:0/005> system.img
<ID:0/005> userdata.img
<ID:0/005> modem.bin
<ID:0/005> Transmission Complete..
<ID:0/005> Now Writing.. Please wait about 2 minutes
<ID:0/005> Receive Response from boot-loader
<ID:0/005> cache.img
<ID:0/005> hidden.img
<ID:0/005> RQT_CLOSE !!
<ID:0/005> RES OK !!
<ID:0/005> Removed!!
<ID:0/005> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
i passed the odin but still the same issue stuck on samsung logo boot loop

chibisan14 said:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin engine v(ID:3.1203)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> sboot.bin
<ID:0/005> param.bin
<ID:0/005> cm.bin
<ID:0/005> boot.img
<ID:0/005> recovery.img
<ID:0/005> system.img
<ID:0/005> userdata.img
<ID:0/005> modem.bin
<ID:0/005> Transmission Complete..
<ID:0/005> Now Writing.. Please wait about 2 minutes
<ID:0/005> Receive Response from boot-loader
<ID:0/005> cache.img
<ID:0/005> hidden.img
<ID:0/005> RQT_CLOSE !!
<ID:0/005> RES OK !!
<ID:0/005> Removed!!
<ID:0/005> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
i passed the odin but still the same issue stuck on samsung logo boot loop
Click to expand...
Click to collapse
After you done this procedure, extract hidden.img from CSC file, rename it to hidden.img.tar, enter in Downloading Mode and flash it in AP on Odin.
After reboot, wait cca 10 - 15min!

<ID:0/005> Added!!
<ID:0/005> Odin engine v(ID:3.1203)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> hidden.img
<ID:0/005> RQT_CLOSE !!
<ID:0/005> RES OK !!
<ID:0/005> Removed!!
<ID:0/005> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
Click to expand...
Click to collapse
done and still not working

any solution for this?

Manual enter to recovery and perform wipe data.
Reboot and wait few minutes afterwards

punktnet said:
Manual enter to recovery and perform wipe data.
Reboot and wait few minutes afterwards
Click to expand...
Click to collapse
can't enter to recovery (vol up + home + power) only download mode and samsung logo bootloop only i can access

chibisan14 said:
done and still not working
Click to expand...
Click to collapse
After you flash "hidden.img.tar" Odin says "PASS" and your phone reboot?
Note that, hidden.img.tar must be rename it by changing the file extension! Is not just an "usual rename" !
Try again the whole procedure.
Otherwise, read this: https://forum.xda-developers.com/s6-edge-plus/help/samsung-galaxy-s6-edge-sm-g928c-twrp-t3192532

dinamo1975 said:
After you flash "hidden.img.tar" Odin says "PASS" and your phone reboot?
Note that, hidden.img.tar must be rename it by changing the file extension! Is not just an "usual rename" !
Try again the whole procedure.
Otherwise, read this: https://forum.xda-developers.com/s6-edge-plus/help/samsung-galaxy-s6-edge-sm-g928c-twrp-t3192532
Click to expand...
Click to collapse
yes it's says pass and phone reboot then coming to boot loop again
yes i change the file extension using 7-zip to tar
tried the link you gaved but its fail got the same issue again "Custom Binary(RECOVERy) blocked by frp lock" in download mode i guess i cant flash twrp recovery anymore because of the frp is on.
is there a solution to off the recovery in download mode?

I think you should try reflash a new image with PIT file from the beginning. Mind you should use a new version with same bootloader as your previous one. Different bootloaders won't install.

Related

GT-P5100 Firmware upgrade encountered an issue

Hi everybody, I tried to upgrade my GT-P5100 to 4.2.2 but something went wrong and now I have a black screen with this message:
Firmware upgrade encountered an issue. Please select recovery mode in Kies & try again.
Probably I have selected Re-Partition but I didn't have a PIT file
The tablet had the stock rom and was not rooted.
I have Odin 3.07 and this PDA file but the procedure fails:
P5100XXDMJ2_P5100VFGDMJ2_P5100XXDMG1_HOME.tar.md5
Code:
<ID:0/011> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> P5100XXDMJ2_P5100VFGDMJ2_P5100XXDMG1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/011> Odin v.3 engine (ID:11)..
<ID:0/011> File analysis..
<ID:0/011> SetupConnection..
<ID:0/011> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I can't start Recovery or Download mode.
Can you help me?
Please if I need some more files write me all the links to download them, because many of them were hosted by hotfile and are no more downloadable...
"Firmware upgrade encountered an issue. Please select recovery mode in Kies & try again."
That´s the Black-Screen of Death! Downloadmode is on in this window Connect to your PC, Odin will get your device
There should be no Problem with the file itself "<OSM> Checking MD5 finished Sucessfully.." - bad download will give another output because the MD5 is not valid if it´s broken.
Make sure you uninstall KIES before using Odin and run Odin as Administrator !!!
Kies in installed and Odin is executed as administrator
So what should I do?
GT-P5100 restore stock rom firmware odin
SOLVED using this guide and this file
dylan6662 said:
SOLVED using this guide and this file
Click to expand...
Click to collapse
Hello, i have the same your prblem with my galaxy tab 2 10.1 !!!...
do you remember how you managed to solve?
Do you remember what was the file of "this link" (http://www.bergfiles.com/i/bf5bdebbf2hci0) that is no longer active?...
I have absoluty need !!
THANKS !!!
Still on trouble
I still can find the right link to download the necessary file to flash on my gt-p5100 like this case , my screen just still say "Firmware upgrade encountered......"
cant log into download mode
but still detect on odin
please help me.
Hi all. I have the same problem. A message "Firmware .... an issue" Tried different Odin versions. With 3.07 and 3.10 versions looks like flashing is ok, Odin shows no errors. But nothing on the tablet, there's not status bar. And when flashing finished, Odin shows no errors. But tablet really not flashed. What the problem can be? Who can help?
HELP HELP
andrezerotwo said:
HELP HELP
Click to expand...
Click to collapse
http://forum.xda-developers.com/gal...opment/odin-gt-p5100-4-2-2-stock-rom-t3022183
try this link, it is stock firmware.
further if it can't solve by just flashing firmware, you can try pit file. but be careful before flashing this with odin, be sure of what it will do, there are guides to explain the proper process.
http://forum.xda-developers.com/showthread.php?t=2552155
I have the exact same problem, tried different odin versions, flashed the stock firmware, also tried different pc's, but no solution.
this is the error I keep getting on odin, Tried Kies it says P3100 does not support initializing. A friend says maybe its a motherboard issue, is that possible or just a firmware problem? What should I do next?
This is the error I get in ODIN.
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> P3100DDCNA3_P3100ODDCNB1_P3100DDCLK1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> system.img
<ID:0/004> NAND Write Start!!
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
v1v14n said:
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> system.img
<ID:0/004> NAND Write Start!!
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
Hi! With my tablet the same. I understand that eMMC has died, need a replacement and reflashing of the programmer.
GT-P5100 Firmware upgrade encountered an issu
Hi All,
I have the exact same problem with GT P5100, I cannot update my 5100,Itried different odin (1.85,307,309,1,7) versions, flashed different firmwares, but no solution.
this is the error I keep getting on odin.
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> P5100XXDMD1_P5100DBTDMD1_P5100XXDLL2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> system.img
<ID:0/005> NAND Write Start!!
<ID:0/005> boot.img
<ID:0/005> cache.img
<ID:0/005> hidden.img
<ID:0/005> recovery.img
<ID:0/005> modem.bin
<ID:0/005> MLO
<ID:0/005> param.lfs
<ID:0/005> Sbl.bin
<ID:0/005> RQT_CLOSE !!
<ID:0/005> RES OK !!
<ID:0/005> Removed!!
Many thanks in advance,

Help s3 gt i9300

So I rooted and rom my galaxy note just fine even help a friend to recover his note 2.
But another friend try to root or place a rom on his S3 I dont know really and now the samsung galaxy sIII gt I9300 is stock on that logo.
So far I've try the following
Odin3 v3.07
philz_touch_6.07.9-i9300.tar.md5
I get:
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> philz_touch_6.07.9-i9300.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> recovery.img
<ID:0/006> NAND Write Start!!
<ID:0/006> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1
odin3 v1.85.exe
CF-Root-SG3-V6.1.TAR
DRIVER SW installation is ok
I get:
<ID:0/007> Added!!
<ID:0/007> Odin v.3 engine (ID:7)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> recovery.img
<ID:0/007> NAND Write Start!!
<ID:0/007>
<ID:0/007> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
odin3 v3.07
I9300UBELL6_I9300UBELL1_I9300CRCELL_1HOME.tar.md5
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300UBELL6_I9300UBELL1_I9300CRCELL1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> boot.img
<ID:0/006> NAND Write Start!!
<ID:0/006> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
I had try this one from xda as well:
- Unzip the attached Odin3-vX.X.zip file
- Download and unzip the CF-Auto-Root-....zip file (see posts below this one)
- If you end up with a recovery.img and cache.img file, you've extracted twice. You need to end up with a .tar.md5 file - don't extract that one
- (USB) Disconnect your phone from your computer
- Start Odin3-vX.X.exe
- Click the PDA button, and select CF-Auto-Root-....tar.md5
- Put your phone in download mode (turn off phone, then hold VolDown+Home+Power to boot - if it asks you to press a button to continue, press the listed button, or run adb reboot download command)
- (USB) Connect the phone to your computer
- Make sure Repartition is NOT checked
- Click the Start button
- Wait for Android to boot
- Done (if it took you more than 30 seconds, you need practise!)
- NOTE: Sometimes the device does *not* boot into recovery mode and root your device. Just do the entire procedure again if this happens. If it still will not install root and such, make sure that in Odin "Auto Reboot" is not checked. Then after flashing, pull the battery, and boot with VolUp+Home+Power button to boot into recovery manually. This will start the install process.
But this last doesn’t work either…
Choko888 said:
So I rooted and rom my galaxy note just fine even help a friend to recover his note 2.
But another friend try to root or place a rom on his S3 I dont know really and now the samsung galaxy sIII gt I9300 is stock on that logo.
So far I've try the following
Odin3 v3.07
philz_touch_6.07.9-i9300.tar.md5
I get:
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> philz_touch_6.07.9-i9300.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> recovery.img
<ID:0/006> NAND Write Start!!
<ID:0/006> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1
odin3 v1.85.exe
CF-Root-SG3-V6.1.TAR
DRIVER SW installation is ok
I get:
<ID:0/007> Added!!
<ID:0/007> Odin v.3 engine (ID:7)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> recovery.img
<ID:0/007> NAND Write Start!!
<ID:0/007>
<ID:0/007> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
odin3 v3.07
I9300UBELL6_I9300UBELL1_I9300CRCELL_1HOME.tar.md5
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300UBELL6_I9300UBELL1_I9300CRCELL1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> boot.img
<ID:0/006> NAND Write Start!!
<ID:0/006> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
I had try this one from xda as well:
- Unzip the attached Odin3-vX.X.zip file
- Download and unzip the CF-Auto-Root-....zip file (see posts below this one)
- If you end up with a recovery.img and cache.img file, you've extracted twice. You need to end up with a .tar.md5 file - don't extract that one
- (USB) Disconnect your phone from your computer
- Start Odin3-vX.X.exe
- Click the PDA button, and select CF-Auto-Root-....tar.md5
- Put your phone in download mode (turn off phone, then hold VolDown+Home+Power to boot - if it asks you to press a button to continue, press the listed button, or run adb reboot download command)
- (USB) Connect the phone to your computer
- Make sure Repartition is NOT checked
- Click the Start button
- Wait for Android to boot
- Done (if it took you more than 30 seconds, you need practise!)
- NOTE: Sometimes the device does *not* boot into recovery mode and root your device. Just do the entire procedure again if this happens. If it still will not install root and such, make sure that in Odin "Auto Reboot" is not checked. Then after flashing, pull the battery, and boot with VolUp+Home+Power button to boot into recovery manually. This will start the install process.
But this last doesn’t work either…
Click to expand...
Click to collapse
Which firmware version is actually installed on the S3 ?
firmware
LS.xD said:
Which firmware version is actually installed on the S3 ?
Click to expand...
Click to collapse
I dont know I got the phone only with de dowload option available, but I think should be
PDA: I9300UBEMH2
CSC: I9300ICEEMH1
MODEM: I9300UBEMH1
Choko888 said:
I dont know I got the phone only with de dowload option available, but I think should be
PDA: I9300UBEMH2
CSC: I9300ICEEMH1
MODEM: I9300UBEMH1
Click to expand...
Click to collapse
Use this CF-AUTO-ROOT --> LINK
and the latest TWRP --> LINK
or the latest PhilZ CWM --> LINK
idk where you got your files from, but they are out of date...
LS.xD said:
Use this CF-AUTO-ROOT -->
and the latest TWRP -->
or the latest PhilZ CWM -->
idk where you got your files from, but they are out of date...
Click to expand...
Click to collapse
with the CF auto root I get:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CF-Auto-Root-m0-m0xx-gti9300.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Added!!
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> recovery.img
<ID:0/006> NAND Write Start!!
<ID:0/006> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
and If I try philz
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> philz_touch_6.26.6-i9300.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Added!!
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> recovery.img
<ID:0/006> NAND Write Start!!
<ID:0/006> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
twrp:
<ID:0/006> Added!!
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> recovery.img
<ID:0/006> NAND Write Start!!
<ID:0/006> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
Have you tried flashing stock firmware first?
Sent from my beloved HTC One S using (most time buggy) Tapatalk
Good
I try to download at sammobile but it doesn't allow me ...
Sent from my GT-N7000 using XDA Free mobile app
Choko888 said:
I try to download at sammobile but it doesn't allow me ...
Sent from my GT-N7000 using XDA Free mobile app
Click to expand...
Click to collapse
use samsung-updates.com instead
LS.xD said:
use samsung-updates.com instead
Click to expand...
Click to collapse
Thanks I think I left one downloading last night I hope its the same one in samsung updates as soon as I get out of work. I´ try it.
LS.xD said:
use samsung-updates.com instead
Click to expand...
Click to collapse
Now I have a doubt, samsung-updates shows CRC (my country)
Galaxy S 3 (International)GT-I9300 CRC I9300UBELL6 4.1.2 31.12.2012 767276 and the information I pull from sammobile said this
Galaxy S 3 (International)GT-I9300 CRC I9300UBEMH2 and samsung updates doesnt have my country code with the same PDA as sammobile.
Do you think samsung-updates has a diferent code for my country? What should I do? Wich one should I pick ?
Choko888 said:
Now I have a doubt, samsung-updates shows CRC (my country)
Galaxy S 3 (International)GT-I9300 CRC I9300UBELL6 4.1.2 31.12.2012 767276 and the information I pull from sammobile said this
Galaxy S 3 (International)GT-I9300 CRC I9300UBEMH2 and samsung updates doesnt have my country code with the same PDA as sammobile.
Do you think samsung-updates has a diferent code for my country? What should I do? Wich one should I pick ?
Click to expand...
Click to collapse
Which firmware is actually installed?
LS.xD said:
Which firmware is actually installed?
Click to expand...
Click to collapse
I dont know I got the phone only with de dowloading option available, Where can I see it if this is the only state of the phone?...
So try the one I think it was for my country I9300UBEMH2_I9300ICEEMH1_ICE but I get
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300UBEMH2_I9300UBEMH1_I9300ICEEMH1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> boot.img
<ID:0/006> NAND Write Start!!
<ID:0/006> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
Since it is international version I try with some firmwares from germany , uk and rusia but it did work either

Norwegian S6 Bricked

Hi, i have a Norwegian Samsung Galaxy S6 and tried to root it using the SM-G920F files from CF-Auto-Root but it didnt work and now my phone wont start with the message: "Recover is not seandroid enforcing" where it says "Samsunng Galaxy S6
Powered by Android". I have tried all the SM-G920F Stock firmwares here but unable to install them, maybe my device should have been rooted before this? Is there i way i can fix my phone now? I cant even shut it down anymore :/
I have tried to follow this guide: autoroot.chainfire but it didnt work and now i have tried to use the UK/spain/Every-Stock-Firmware-for-the-G920F-i-Can-Find.
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G920FXXU1AOCZ_G920FVFG1AOC4_G920FXXU1AOCW_HOME.tar .md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin engine v(ID:3.1005)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> sboot.bin
<ID:0/005> NAND Write Start!!
<ID:0/005> FAIL!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/005> Removed!!
On the phone itself it says "SW REV. CHECK FAIL. DEVICE:2 BINARY:1
With red text.
Is what ODIN3 v3.10 is saying.
To shut down S6 from download mode press volume down + power button at the same time and hold until screen turns off.
After this you have an option to:
1. Bring your S6 bacck to Samsung for warranty repair.
2. Use a different USB cable or try a different USB port then reflash again.
I hope this helps.
roydok said:
To shut down S6 from download mode press volume down + power button at the same time and hold until screen turns off.
After this you have an option to:
1. Bring your S6 bacck to Samsung for warranty repair.
2. Use a different USB cable or try a different USB port then reflash again.
I hope this helps.
Click to expand...
Click to collapse
It Says KNOX warranty void 1, this means that warranty is broken? I am going to get my original samsung s6 USB cable tomorrow to try.
Install twrp and port any costum room and you will fix your s6...
Or download newest version in sammobile of g920f stock firmware. You are failing at sboot. That mean bootloader in the phone os newer than the one you trying to install
Now it does not fail right away, but it still fails after a short while. Will the process fail if i don't do anything on the device itself? Because now it starts doing something in Odin, but returns fail after a while, but i am not with the phone as it is home right now.
This is what ODIN says now:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G920FXXU2BOFL_G920FOJV2BOEE_G920FXXU2BOFJ_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin engine v(ID:3.1005)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> sboot.bin
<ID:0/005> NAND Write Start!!
<ID:0/005> cm.bin
<ID:0/005> boot.img
<ID:0/005> recovery.img
<ID:0/005> system.img
<ID:0/005> modem.bin
<ID:0/005> cache.img
<ID:0/005> hidden.img
<ID:0/005> FAIL!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Try redownloading your ROM. There might be errors in the file resulting from the download.

Help my S6 from T mobile seems screwed

Idk whats going on I used the odin3 download stock firmware to try to restore the phone after boot loop I tried to install TWRP custom recovery it didnt reboot into and so i tried to restore through odin3 and stock frimware and it says failed. Any ideas thanks
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G920TUVU1AOCG_G920TTMB1AOCG_G920TUVU1AOCG_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin engine v(ID:3.1005)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> sboot.bin
<ID:0/005> NAND Write Start!!
<ID:0/005> FAIL!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
make sure re-partition is unchecked from the options tab.
Sent from my SM-G920I using Tapatalk
Try :
1. Using a different USB cable or USB port.
2. Redownload again your ROM as download errors can cause flash failures.
3. Lastly, consider bringing your S6 back to Samsung for warranty repair. Its free within your warranty period.
I hope this helps.

[Help] Galaxy S 6 G920W8 stuck on SAMSUNG logo during boot

So I have a samsung Galaxy S 6 (G920W8) that I cannot get to boot into Android.
I was able to get the device into recovery and download mode, and I'm able to install TWRP on the device, boots into that with zero problems.
I've been able to use TWRP to install custom ROMs and kernels, and I can use an older version of ODIN to flash the correct carrier ROM to the phone, but newer version fail on the NAND WRITE step. TWRP gives no errors when attempting to flash, and I have access to the whole memory of the device.
Is there any hope for this device?
Code:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G920W8VLU3BOL1_G920W8OYA3BOL1_G920W8VLU3BOL1_HOME.tar.md5 is invalid.
<OSM> End...
<Accidentally tried adding file before it was done unzipping>
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin engine v(ID:3.1100)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> sboot.bin
<ID:0/005> NAND Write Start!!
<ID:0/005> cm.bin
<ID:0/005> boot.img
<ID:0/005> recovery.img
<ID:0/005> system.img
<ID:0/005> cache.img
<ID:0/005> modem.bin
<ID:0/005> RQT_CLOSE !!
<ID:0/005> RES OK !!
<ID:0/005> Removed!!
<ID:0/005> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
That's the result in Odin after trying to flash that carrier ROM with Odin3 v3.10.7. Now the device is still boot looping. I don't understand what's wrong.
DisturbenChamp said:
Code:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G920W8VLU3BOL1_G920W8OYA3BOL1_G920W8VLU3BOL1_HOME.tar.md5 is invalid.
<OSM> End...
<Accidentally tried adding file before it was done unzipping>
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin engine v(ID:3.1100)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> sboot.bin
<ID:0/005> NAND Write Start!!
<ID:0/005> cm.bin
<ID:0/005> boot.img
<ID:0/005> recovery.img
<ID:0/005> system.img
<ID:0/005> cache.img
<ID:0/005> modem.bin
<ID:0/005> RQT_CLOSE !!
<ID:0/005> RES OK !!
<ID:0/005> Removed!!
<ID:0/005> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
That's the result in Odin after trying to flash that carrier ROM with Odin3 v3.10.7. Now the device is still boot looping. I don't understand what's wrong.
Click to expand...
Click to collapse
Boot into recovery and factory reset.
Sent from my SM-G925F
Rosli59564 said:
Boot into recovery and factory reset.
Sent from my SM-G925F
Click to expand...
Click to collapse
I have tried that. The device continues to boot loop, even when wiped through official recovery or TWRP recovery.
DisturbenChamp said:
I have tried that. The device continues to boot loop, even when wiped through official recovery or TWRP recovery.
Click to expand...
Click to collapse
Try to reinitialize the phone with smart switch. Maybe it's the firmware you flashed with odin.
Sent from my SM-G925F
Rosli59564 said:
Try to reinitialize the phone with smart switch. Maybe it's the firmware you flashed with odin.
Sent from my SM-G925F
Click to expand...
Click to collapse
Smart Switch nor Kies will connect to the device., but odin and MTP via TWRP both work. I've attempted a 5.0.2 and 5.1.1 ROM from the carrier, the ROMs are from Sam-Firmware, and I am currently downloading a 6.0.1 file to attempt and flash..
Sometimes in Download mode it displays the following error:
Code:
SW REV CHECK FAIL. DEVICE: 3, BINARY: 1
OR
SW REV CHECK FAIL. DEVICE: 3, BINARY: 2

Categories

Resources