So I rooted and rom my galaxy note just fine even help a friend to recover his note 2.
But another friend try to root or place a rom on his S3 I dont know really and now the samsung galaxy sIII gt I9300 is stock on that logo.
So far I've try the following
Odin3 v3.07
philz_touch_6.07.9-i9300.tar.md5
I get:
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> philz_touch_6.07.9-i9300.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> recovery.img
<ID:0/006> NAND Write Start!!
<ID:0/006> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1
odin3 v1.85.exe
CF-Root-SG3-V6.1.TAR
DRIVER SW installation is ok
I get:
<ID:0/007> Added!!
<ID:0/007> Odin v.3 engine (ID:7)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> recovery.img
<ID:0/007> NAND Write Start!!
<ID:0/007>
<ID:0/007> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
odin3 v3.07
I9300UBELL6_I9300UBELL1_I9300CRCELL_1HOME.tar.md5
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300UBELL6_I9300UBELL1_I9300CRCELL1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> boot.img
<ID:0/006> NAND Write Start!!
<ID:0/006> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
I had try this one from xda as well:
- Unzip the attached Odin3-vX.X.zip file
- Download and unzip the CF-Auto-Root-....zip file (see posts below this one)
- If you end up with a recovery.img and cache.img file, you've extracted twice. You need to end up with a .tar.md5 file - don't extract that one
- (USB) Disconnect your phone from your computer
- Start Odin3-vX.X.exe
- Click the PDA button, and select CF-Auto-Root-....tar.md5
- Put your phone in download mode (turn off phone, then hold VolDown+Home+Power to boot - if it asks you to press a button to continue, press the listed button, or run adb reboot download command)
- (USB) Connect the phone to your computer
- Make sure Repartition is NOT checked
- Click the Start button
- Wait for Android to boot
- Done (if it took you more than 30 seconds, you need practise!)
- NOTE: Sometimes the device does *not* boot into recovery mode and root your device. Just do the entire procedure again if this happens. If it still will not install root and such, make sure that in Odin "Auto Reboot" is not checked. Then after flashing, pull the battery, and boot with VolUp+Home+Power button to boot into recovery manually. This will start the install process.
But this last doesn’t work either…
Choko888 said:
So I rooted and rom my galaxy note just fine even help a friend to recover his note 2.
But another friend try to root or place a rom on his S3 I dont know really and now the samsung galaxy sIII gt I9300 is stock on that logo.
So far I've try the following
Odin3 v3.07
philz_touch_6.07.9-i9300.tar.md5
I get:
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> philz_touch_6.07.9-i9300.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> recovery.img
<ID:0/006> NAND Write Start!!
<ID:0/006> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1
odin3 v1.85.exe
CF-Root-SG3-V6.1.TAR
DRIVER SW installation is ok
I get:
<ID:0/007> Added!!
<ID:0/007> Odin v.3 engine (ID:7)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> recovery.img
<ID:0/007> NAND Write Start!!
<ID:0/007>
<ID:0/007> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
odin3 v3.07
I9300UBELL6_I9300UBELL1_I9300CRCELL_1HOME.tar.md5
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300UBELL6_I9300UBELL1_I9300CRCELL1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> boot.img
<ID:0/006> NAND Write Start!!
<ID:0/006> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
I had try this one from xda as well:
- Unzip the attached Odin3-vX.X.zip file
- Download and unzip the CF-Auto-Root-....zip file (see posts below this one)
- If you end up with a recovery.img and cache.img file, you've extracted twice. You need to end up with a .tar.md5 file - don't extract that one
- (USB) Disconnect your phone from your computer
- Start Odin3-vX.X.exe
- Click the PDA button, and select CF-Auto-Root-....tar.md5
- Put your phone in download mode (turn off phone, then hold VolDown+Home+Power to boot - if it asks you to press a button to continue, press the listed button, or run adb reboot download command)
- (USB) Connect the phone to your computer
- Make sure Repartition is NOT checked
- Click the Start button
- Wait for Android to boot
- Done (if it took you more than 30 seconds, you need practise!)
- NOTE: Sometimes the device does *not* boot into recovery mode and root your device. Just do the entire procedure again if this happens. If it still will not install root and such, make sure that in Odin "Auto Reboot" is not checked. Then after flashing, pull the battery, and boot with VolUp+Home+Power button to boot into recovery manually. This will start the install process.
But this last doesn’t work either…
Click to expand...
Click to collapse
Which firmware version is actually installed on the S3 ?
firmware
LS.xD said:
Which firmware version is actually installed on the S3 ?
Click to expand...
Click to collapse
I dont know I got the phone only with de dowload option available, but I think should be
PDA: I9300UBEMH2
CSC: I9300ICEEMH1
MODEM: I9300UBEMH1
Choko888 said:
I dont know I got the phone only with de dowload option available, but I think should be
PDA: I9300UBEMH2
CSC: I9300ICEEMH1
MODEM: I9300UBEMH1
Click to expand...
Click to collapse
Use this CF-AUTO-ROOT --> LINK
and the latest TWRP --> LINK
or the latest PhilZ CWM --> LINK
idk where you got your files from, but they are out of date...
LS.xD said:
Use this CF-AUTO-ROOT -->
and the latest TWRP -->
or the latest PhilZ CWM -->
idk where you got your files from, but they are out of date...
Click to expand...
Click to collapse
with the CF auto root I get:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CF-Auto-Root-m0-m0xx-gti9300.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Added!!
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> recovery.img
<ID:0/006> NAND Write Start!!
<ID:0/006> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
and If I try philz
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> philz_touch_6.26.6-i9300.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Added!!
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> recovery.img
<ID:0/006> NAND Write Start!!
<ID:0/006> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
twrp:
<ID:0/006> Added!!
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> recovery.img
<ID:0/006> NAND Write Start!!
<ID:0/006> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
Have you tried flashing stock firmware first?
Sent from my beloved HTC One S using (most time buggy) Tapatalk
Good
I try to download at sammobile but it doesn't allow me ...
Sent from my GT-N7000 using XDA Free mobile app
Choko888 said:
I try to download at sammobile but it doesn't allow me ...
Sent from my GT-N7000 using XDA Free mobile app
Click to expand...
Click to collapse
use samsung-updates.com instead
LS.xD said:
use samsung-updates.com instead
Click to expand...
Click to collapse
Thanks I think I left one downloading last night I hope its the same one in samsung updates as soon as I get out of work. I´ try it.
LS.xD said:
use samsung-updates.com instead
Click to expand...
Click to collapse
Now I have a doubt, samsung-updates shows CRC (my country)
Galaxy S 3 (International)GT-I9300 CRC I9300UBELL6 4.1.2 31.12.2012 767276 and the information I pull from sammobile said this
Galaxy S 3 (International)GT-I9300 CRC I9300UBEMH2 and samsung updates doesnt have my country code with the same PDA as sammobile.
Do you think samsung-updates has a diferent code for my country? What should I do? Wich one should I pick ?
Choko888 said:
Now I have a doubt, samsung-updates shows CRC (my country)
Galaxy S 3 (International)GT-I9300 CRC I9300UBELL6 4.1.2 31.12.2012 767276 and the information I pull from sammobile said this
Galaxy S 3 (International)GT-I9300 CRC I9300UBEMH2 and samsung updates doesnt have my country code with the same PDA as sammobile.
Do you think samsung-updates has a diferent code for my country? What should I do? Wich one should I pick ?
Click to expand...
Click to collapse
Which firmware is actually installed?
LS.xD said:
Which firmware is actually installed?
Click to expand...
Click to collapse
I dont know I got the phone only with de dowloading option available, Where can I see it if this is the only state of the phone?...
So try the one I think it was for my country I9300UBEMH2_I9300ICEEMH1_ICE but I get
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300UBEMH2_I9300UBEMH1_I9300ICEEMH1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> boot.img
<ID:0/006> NAND Write Start!!
<ID:0/006> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
Since it is international version I try with some firmwares from germany , uk and rusia but it did work either
Related
Hi Guys,
I have AT&T Note edge and i tried to install kitkat on it by using the files from the following link
http://androidromupdate.com/att-gala...tock-firmware/
and i tried this also
http://www.androidrootz.com/p/galaxy...-firmware.html,
and this too
http://forum.xda-developers.com/note...files-t3108344
getting the error like this
<ID:0/006> Added!! <OSM> Enter CS for MD5.. <OSM> Check MD5.. Do not unplug the cable.. <OSM> Please wait.. <OSM> CF-Auto-Root-trltetmo-trltetmo-smn910t.tar.md5 is valid. <OSM> Checking MD5 finished Sucessfully.. <OSM> Leave CS.. <ID:0/006> Odin v.3 engine (ID:6).. <ID:0/006> File analysis.. <ID:0/006> SetupConnection.. <ID:0/006> Initialzation.. <ID:0/006> Get PIT for mapping.. <ID:0/006> Firmware update start.. <ID:0/006> recovery.img <ID:0/006> NAND Write Start!! <ID:0/006> cache.img.ext4 <ID:0/006> FAIL! (Auth) <OSM> All threads completed. (succeed 0 / failed 1)
and i bricked my phone, i can go only in to download mode.. pls help out.
saisagar said:
Hi Guys,
I have AT&T Note edge and i tried to install kitkat on it by using the files from the following link
http://androidromupdate.com/att-gala...tock-firmware/
and i tried this also
http://www.androidrootz.com/p/galaxy...-firmware.html,
and this too
http://forum.xda-developers.com/note...files-t3108344
getting the error like this
<ID:0/006> Added!! <OSM> Enter CS for MD5.. <OSM> Check MD5.. Do not unplug the cable.. <OSM> Please wait.. <OSM> CF-Auto-Root-trltetmo-trltetmo-smn910t.tar.md5 is valid. <OSM> Checking MD5 finished Sucessfully.. <OSM> Leave CS.. <ID:0/006> Odin v.3 engine (ID:6).. <ID:0/006> File analysis.. <ID:0/006> SetupConnection.. <ID:0/006> Initialzation.. <ID:0/006> Get PIT for mapping.. <ID:0/006> Firmware update start.. <ID:0/006> recovery.img <ID:0/006> NAND Write Start!! <ID:0/006> cache.img.ext4 <ID:0/006> FAIL! (Auth) <OSM> All threads completed. (succeed 0 / failed 1)
and i bricked my phone, i can go only in to download mode.. pls help out.
Click to expand...
Click to collapse
download stock firmware from here, flash via odin http://androidromupdate.com/att-galaxy-note-edge-sm-n915a-stock-firmware/
flipmodeseven said:
download stock firmware from here, flash via odin http://androidromupdate.com/att-galaxy-note-edge-sm-n915a-stock-firmware/
Click to expand...
Click to collapse
i have already downloaded from the same website
saisagar said:
i have already downloaded from the same website
Click to expand...
Click to collapse
replied
Listen, I have a canaidian Telus Galaxy s6 G920w8 and it wont let me flash my stock firmware. WHAT DO I DO? Here is my odin log,
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G920W8VLU1AOCG_G920W8OYA1AOCG_G920W8VLU1AOCG_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin engine v(ID:3.1005)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> SingleDownload.
<ID:0/006> sboot.bin
<ID:0/006> NAND Write Start!!
<ID:0/006> FAIL!
<ID:0/006>
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I can only access download mode and nothing else, Someone please help me!
I cant flash anything? Its so messed up
shotgun10ga said:
Listen, I have a canaidian Telus Galaxy s6 G920w8 and it wont let me flash my stock firmware. WHAT DO I DO? Here is my odin log,
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G920W8VLU1AOCG_G920W8OYA1AOCG_G920W8VLU1AOCG_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin engine v(ID:3.1005)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> SingleDownload.
<ID:0/006> sboot.bin
<ID:0/006> NAND Write Start!!
<ID:0/006> FAIL!
<ID:0/006>
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I can only access download mode and nothing else, Someone please help me!
I cant flash anything? Its so messed up
Click to expand...
Click to collapse
Hi,
Thank you using XDA assist. Good news you have specific forum dedicated specially for your device here http://forum.xda-developers.com/galaxy-s6-edge/help
You can get help there from the experts.
Good luck
Sent from my A0001 using Tapatalk 2
two days ago my gsm stop working and is stuck on logo picture and so after checking some sites online i have found that using program ODIN and flushing a new rom will help but it did not it gives this error and a FAIL
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin engine v(ID:3.1203)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> SingleDownload.
<ID:0/006> sboot.bin
<ID:0/006> FAIL!
<ID:0/006>
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/006> Removed!!
even i tried to reset to factory settings and did not work so can any one help me please
janezz2 said:
two days ago my gsm stop working and is stuck on logo picture and so after checking some sites online i have found that using program ODIN and flushing a new rom will help but it did not it gives this error and a FAIL
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin engine v(ID:3.1203)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> SingleDownload.
<ID:0/006> sboot.bin
<ID:0/006> FAIL!
<ID:0/006>
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/006> Removed!!
even i tried to reset to factory settings and did not work so can any one help me please
Click to expand...
Click to collapse
Greetings and welcome to xda, have you tried kies emergency firmwarw recovery ? I used it to restore my note 2 lte
Good Luck
Sawdoctor
sawdoctor said:
Greetings and welcome to xda, have you tried kies emergency firmwarw recovery ? I used it to restore my note 2 lte
Good Luck
Sawdoctor
Click to expand...
Click to collapse
where can i get this frimware recovery?
It is an option in kies. Just download Samsung kies to your pc and select the option
i rooted my device recently and tried updating my se or su binary yesterday, my mobile never turned on except for bootloop
i try installing fresh stock rom and this is what i get,
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin engine v(ID:3.1203)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> SingleDownload.
<ID:0/006> sboot.bin
<ID:0/006> FAIL!
<ID:0/006>
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/006> Removed!!
can soimeone help me with the process please?
Govardhankrishna said:
i rooted my device recently and tried updating my se or su binary yesterday, my mobile never turned on except for bootloop
i try installing fresh stock rom and this is what i get,
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin engine v(ID:3.1203)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> SingleDownload.
<ID:0/006> sboot.bin
<ID:0/006> FAIL!
<ID:0/006>
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/006> Removed!!
can soimeone help me with the process please?
Click to expand...
Click to collapse
Greetings and welcome to assist. The easiest way to recover your device is by using kies/smartswitch emergency firmware recovery but you will lose your data
Good Luck
Sawdoctor
Hello there!
My phone is in Bootloop and i'm trying to flash the original firmware with Odin, but i'm getting an fail:
Odin error:
<ID:0/006> Removed!!
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin engine v(ID:3.1205)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> SingleDownload.
<ID:0/006> boot.img
<ID:0/006> cache.img
<ID:0/006> cm.bin
<ID:0/006> FAIL!
<ID:0/006>
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Phone error:
[CM] SW REV. check fail device: 5, binary 3
I'm from Netherlands, with an unlocked phone but i'm Using Vodafone as a provider.
Can someone please help me in the right direciton.
thanks in advance!
EDIT: Fixed the problem myself
for those wanne know how: I tried to flash a different firmware and that worked.
bro try a firmware with 4 files just google it