My 1020 got bricked while flashing through WPInternals.
In the middle of the flashing the USB got disconnected and after that I have blank screen. The power button pressing does make phone vibrate. Also soft reset combination makes vibration. However I am not getting anything on my laptop on USB connection. No connection notification. Nothing on device manager. I tried combinations to get it detected but nothing works.
So the question is, Is there any way I can blindly send force flashing to one of the USB port and make it happen ?
JTAG is the only option ?
Related
Hi Guys.
It might seem funny. I do not have a PDAphone but I have a problem with my HPiPAQ hx2795. And I would greatly appreciate any comments or tips.
Here is the story:
I was trying to update setup/ROM. the first three updates went well. The forth one, didn't go through; it was showing time-out. it happened twice, the third time, I noticed a message on the left lower corner of the device,saying Connect A/C to flash, I tried to do it quickly before getting time-out. I guess I didn't do it quick enough. Anyway I plugged in the power to the cradle and it started flashing the ROM then I got the time-out error again. The screen reset and stuck @100% not going any further. To make it worse to me, it was not detectable by MS ActiveSync at all. I tried the active chat with the tech support of HP they said all is left for me to do is "going to parrot mode (= USB /serial Mode) and if the OS is not corrupted then I can repeat the ROM update and fix it" which I did with no luck as even in parrot mode, the device would noticed that the USB is connected but the PC would NOT recognize the device.
While I was searching the internet, I came across your site, beautiful and very interesting. I saw some people is using a program called NVID.exe.
IS THERE ANY SOFTWARE LIKE NVID.EXE THAT I CAN USE IT TO SOLVE MY PROBLEM on this HPiPAQ.
I was wondering about using something like that to get the device detectable by PC again. Is is possible even theoretically?
Please HELP.
I greatly appreciate all your comments and tips in advance.
Did you tried to do a clean reset? Or to put the device in bootloader or white bootloader mode and try to connect and see if recognize it?
Hard reset: butons 1+4+reset
Clean reset: buttons 1+3+power+reset
White bootloader mode: buttons 2+4+reset
what you call it "white bootloader mode" they call it "parrot mode". and yes I did try that. In that mode it shows Pre-BL: 1.00.04 that shows USB is connected or USB Cable is removed; however; my Win XP cannot recognize the new USB device.
Is there any way to make PC recognize this "HPiPAQ hx2795 in Parrot Mode". I mean any driver for WinXP to recognize this USB device as reachable device (updatable ROM)? Maybe that could be the "MAGIC KEY" to solve all people's problem suffering from such an issue?
I hear about mytt11.exe alot in posts here and there. What does it do? Where can I find it in order to give it a try?
Coolluck
------------------
HPiPAQ hx2795-WM5, failed ROM update
Hello everyone.
Once upon a time i came to my TP and tried to activate the screen. nothing happened. Screen dead - only very faint backlight showed up. So i thought, maybe the ROM went bad somehow. So i tried soft reset. No change. I tried Hard-reset (which is not as easy when you dont see a thing). Now i thought, ok, just flash it again. BUT thats when the heavy thing came in. The USB cabel doesnt work. It does charge through the cable, but the PC doesnt recognize it at all. Anyone has an idea how i could get in connection with it? If i cannot bring up a USB connection will the guys at the repair factory be ale to connect somehow? I still have warranty (time-wise).
I will be gratefull for any idea on how to make the USB connection or how to flash without USB connection.
After some trying i found out that Windows somehow reserves USB slots for certain devices and after plugging the cable into different slot i managed to get a Sync and USB connection.
Then i faced the problem with returning "blinded" stock ROM and stock SPL. Thanks to the great guides here i managed to download a Stock ROM and flash it onto the Raphael. Then i faced the problem with putting in the Stock SPL, but it worked once i put the device into bootloader mode with Volume Down + reset.
So now i hope my device is as Stock as i bought it, and i will be sending it in for warranty repair or exchange. I hope its just some minor problem with display.
My phone only shows the the elephone 2 e sign when I turn it on. I have tried pressing the on and volume key when I turn it on but nothing happened. I have followed some instructions on the elephone manufacturer site about installing drivers to my computer and then trying to reinstall the firmware. Unfortunately my computers (I have tried on three different ones) does not identify that a device is connected to the computer. Therefore I can't proceed to install the driver as according to my computer it is not installed. I have tried 2 different leads as well. I would be grateful for some help as I have no idea where to go from here.
Facing a similar issue, and since there's still no reply to this thread, I would like to add up a few findings I have on this matter to maybe help others and get helped.
My P3000S is also reaching the Elephone logo and displays it for a minute and then restarts, repeating the process (aka boot-loop).
The same happens whether it is connected or not connected to the charger/computer through a USB cable. (I've tried new cables but that's not the case).
When disconnected I can stop the boot-loop only by holding down the on/off button for a few seconds (or removing the battery of course).
When connected to the the charger or computer through the USB cable I have no way to stop the boot-loop (holding down on/off just restarts it).
Now with the battery removed..:
If I connect it to the charger/computer, though the charging red light turns on normally, I can't turn on the phone using the on/off button.
However, when connected through USB to a windows computer, I can see in the device manager that, right when I connect the phone it shows up as "Mediatek Preloader USB VCOM Port" under COM ports group, for 1 second and then disappears as if it was disconnected. There's no repetition here I have to manually hold down the on/off button or disconnect and reconnect the phone from the cable to cause this to happen again.
So, I am unable to flash anything nor turn the phone on because I practically only have 1 second of its presence in my devices list.
Also, I have tried all possible combinations with the volume up/down keys and the on/off button in order to enter recovery mode, with no success..
In case anyone has faced something similar or has any ideas on a possible fix on this phone please feel free to reply.
At last a reply to my initial message. Unfortunately it was someone with the same problem as me. I took out a paypal case against the person I bought the phone from and eventually they repaired it. Unfortunately they never told me how. To make matters worse it broke again within 2 months. The phone is now sat in a draw doing nothing. I have given up on it and will never buy another Elephone phone again.
SOLVED: S7 dropped > broken screen > how to recover images? Not rooted,not "usb mode"
So my wife dropped S7 to the floor and device ended up to be fully powered, but screen is now all black. Back and "software" button illuminates. I can change volume. I can take photos. So phone works, but screen is all black. Main concern is to have photos out from the phone. Contacts are synced, software etc. can be installed to new phone.
Kies finds the phone, but says that is' locked. Although phone does not have any passcodes or fingerprint, Kies cannot access to photos. Also the PC does see the device, but it won't allow me to see the contents. Find My Mobile is not activated, I think that I can't activate it now without phone. Also Smart Switch says that phone is locked. Phone settings are pretty much as out from the box. USB debugging is off, Developper options off, etc...
But I found that possible via ABD (?) I could access phone storage. Is it so? I sould start the phone to Recovery Mode / Download Mode? How to do that? Normally the phone is on and I can't switch it off. I can only soft reset is by keeping vol- + power buttons pressed for 10sec. But after that, phone just restarts to OS.
Please give hints how to proceed. What to try. New LCD is around 50USD and takes forever to get from Aliexpress/Ebay.
Why not use an external display? Hook it up to the USB-connector via an adaptor and it should work to unlock the phone using a PC-mouse.
gedhe said:
Why not use an external display? Hook it up to the USB-connector via an adaptor and it should work to unlock the phone using a PC-mouse.
Click to expand...
Click to collapse
O, it has such feature? Quick googling did not help how to do it. How does it work? Do I need some cable or device?
Any ideas how to proceed? I either can reboot device to Recovery mode and use ADB or connect external display to the device. Or if someone has any better solution
Please help. Family photos are in the phone
Try to unlock your lock screen with a usb mouse connected via otg and swiping up with the mouse. Then connect it to the computer and try to backup your data with kies or switch.
Tried many thing how to allow the connection from another phone or computer. However it was not possible to connect, so I ordered a new screen. Once new screen installed, it was not even a challenge Ordered new screen from Aliexpress.
Hello,
I have a HTC U11 which appeared to have bricked during a hard reset - it froze and I used the power and volume down button to force a reset. It turned off but didn't appear to turn on again. I took it to a repairer which tried to replace both the screen and battery before telling me that it's economically unviable to repair because there is an issue with the motherboard. I've already got a replacement phone but I didn't have any of the data on my HTC backed up.
I've got Android studios and the naked adb driver set but when I connect it to my PC via usb it makes the sound of a device being connected and disconnected but won't detect the device - not even in device manager. Is there any possibility I will be able to access to the internal storage of the phone through my pc given these complications or will I have to see if a professional data recovery specialist can recover my data?