[GUIDE] Smart Switch Emergency Initialization - Galaxy S6 Q&A, Help & Troubleshooting

Hello,
I see that some people have problems using Smart Switch emergency initialization, so I made this step by step instructions.
Hope that helps
1. Open Smart Switch and click on More in upper right corner
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
2. Select Emergency software recovery and reinitialization from the drop down menu
3. Click on Device initialization tab
4. Type device model in capital letters with SM- infront as shown on the picture below, and clik on search button
5. Type serial number from back of the phone and clik OK
6. Clik OK again
7. and again OK
8. Follow the onscreen instructions (enter download mode (hold Volume down + Home + Power buton (then Volume Up to confirm when blue screen appears on the phone)), and conect the USB cable), and click OK
9. Wait till process is complete.

i have tried my device S/N and it says "SM-G920F does not support initializing"
and when i enter 123456789 it says "S/N you entered it incorrect"

kamilmirza said:
i have tried my device S/N and it says "SM-G920F does not support initializing"
and when i enter 123456789 it says "S/N you entered it incorrect"
Click to expand...
Click to collapse
you have to put the serial number of the device which is usually on the that ticket on the phone back

after step 7 it says.. ,,Preparing for update and initialization of Galaxy s6+ edge'' then once it hits 100% pop up disappears and thats everything.. goes no further.. any advice? help?

Revuella said:
after step 7 it says.. ,,Preparing for update and initialization of Galaxy s6+ edge'' then once it hits 100% pop up disappears and thats everything.. goes no further.. any advice? help?
Click to expand...
Click to collapse
At that point Smart Switch is downloading fw, and storing it to temp folder.
Have u tried reinstaling Smart Switch? Disabling anivirus for 5 min? And make sure u have enough disk space on partition where temp folder is.

I'm getting the same message yet I've correctly input the serial number etc

when I try to use emergency recovery from the menu it show no tabs nothing what am I doing wrong

When i put the s/n and push ok th smart switch shuts down

Hi where can i get this version of smart switch please. I have downloaded it from samsung and other sites but none have recovery and initialization tab. Can only use emergency code. Any help welcome and thanks.

Related

Image File Corrupt

I'm trying to flash a new ROM and can't get past the USPL stage
I run the 'uspl_116_jockyw.bat' and pause it on the "start MTTY [or whatever] or RUU" and I then try to the run the ROMUpdateUtilitiy.exe.
All goes well, but at 100%, it says "Image file is corrupt" and then that's it, it restarts.
I've tried different versions of the file with no success
Is it to do with my Application unlock? When I run that is says something along the lines of "SDA [or phone] is not unlockable" but I click unlock, and it instantly says "unlock successful"
At the moment I've only been able to install Opera. WIFIRouter and Messenger won't install.
Thanks
first unlock with the sda unlock. then flash uspl. run rom update utility.exe. after that run flash.exe on whichever rom it is that u wish to flash. if this doesnt work, do a hard reset and repeat all the steps. 100% it will work. when u get to the final prompt asking u to start mtty or whatever, dont press any key to continue the process. instead run ruu.exe. itll work
So is it normal for the Application Unlock utility to say "This device is not unlockable" [or something along those lines].
I can't install any programs on the deivce either. It says they don't have the correct permissions. Is that not what the app unlocker is meant to do?
EDIT:
OK, so this is what I am doing:
1) hard reset the phone [hold soft keys, turn on, press end etc]
2) connect to ActiveSync
3) Run SDA_ApplicationUnlock.exe
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
4) I click OK and it claims to have unlocked.
5) remove SD card and turn phone off then on.
6) Run uspl_116_jockyw.bat. I hit enter a few times,my phone then asks me to confirm running an app. It does this twice, the last being harat.exe. Screen goes black with Tux the Penguin.
I halt on this screen [Ignore the error - I screen capped this on a later attempt without hard reset]
I then run ROMUpdateUtility.exe check the boxes, and click next etc. It goes to RGB bars, then a grey screen with a progress bar. The bar gets to 100% then I get this error
and the phone resets?
What am I doing wrong?
Any help is appreciate. I can't stand the Orange crippled ROM.
Thanks
Right HERE is the solution for any Orange SPV e650 users wanting to unlock and flash.
These 3 files are crucial:
MoDaCo_SPV_E650_de_Brand___Fix_Pack.PREP.CAB
MoDaCo_SPV_E650_de_Brand___Fix_Pack_0.5.CAB
RemoveSecurity.CAB
Only once those have been run can you follow the steps found on the wiki page.
Thanks to everyone who works on these ROMs. It's is simply awesome the work you do.
I salute you!

[Q] Samsung Duos GT B5512 Can t enter recovery mode

Hi!
I can t enter recovery mode for my Samsung B5512 device. İt is supposed to enter pressing :
volume up + home+power but the debice keeps booting. Also ı have tried to release all buttons when samsung logo appears and also have watched most of the videos in youtube. I am sure that ı am pressing well: is it possible to not have an option available for entering recovery mode?
regards
jetthefast said:
Hi!
I can t enter recovery mode for my Samsung B5512 device. İt is supposed to enter pressing :
volume up + home+power but the debice keeps booting. Also ı have tried to release all buttons when samsung logo appears and also have watched most of the videos in youtube. I am sure that ı am pressing well: is it possible to not have an option available for entering recovery mode?
regards
Click to expand...
Click to collapse
ı guess there is no hope for my phone then
jetthefast said:
ı guess there is no hope for my phone then
Click to expand...
Click to collapse
use other methods as mentioned in My Android Solutions to get into recovery
Check this out!You , YES! you are an " Android ". Not your phone but U.
You Must watch this documentary concerning your privacy Terms & Conditions we had agreed to, by using a PC or Smartphone
How to say Thank you? If you find any post helpful on XDA, please click on the Thanks button
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
If you are using XDA App or Tapatalk, long press on the post and select :good: Thanks Its easier to give "Feedback" in this manner than make an additional post.​
this is an old thread but I struggled with it as well - fully charge it, hit those 3 buttons - try at the same time but if not try volume up and home and then on/off button and hold it until it reboots the phone.
In my case, if you keep holding it the phone will not turn on.
If you release on/off switch it will turn on but can happen that you will come to system in "safe mode"
For me works just holding those 3 buttons until it reboots (phone was turned off then you start it with buttons, keep holding and when reboots release them) and recovery should be shown. If doesn't help try to take out sd card - if you plug it back in while in recovery my b5512 can load it - sometimes with error but in general, it can.
I think main conditions are to have it charged do 75%+
and unsure but to me it looks like to have a good stable sd card.
All the best

Tab 2 Brick And Problem.URGENT!!

So I don't have a Tab 2 but I'm posting this in behalf of my cousin which have a P3110 WiFi only Tab 2 7.0
So I tought my cousin how to do root and stuff.But yesterday,when he flashed CM11,something went wrong and it bricked his Tab.
My cuz contacted me via Facebook for help.At first,the Tab was stuck at the boot screen.But after a few hours,the problem went worse.
The Tab will not turn on by pressing the power button.But when a charger is connected,the Tab turns on but it just shows a battery and a loading circle.Thats it.Ill put a picture on how it looked like somewhere.......down here!
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Well.I need help to fix this.URGENTLY.Thanks
c903jerk said:
So I don't have a Tab 2 but I'm posting this in behalf of my cousin which have a P3110 WiFi only Tab 2 7.0
So I tought my cousin how to do root and stuff.But yesterday,when he flashed CM11,something went wrong and it bricked his Tab.
My cuz contacted me via Facebook for help.At first,the Tab was stuck at the boot screen.But after a few hours,the problem went worse.
The Tab will not turn on by pressing the power button.But when a charger is connected,the Tab turns on but it just shows a battery and a loading circle.Thats it.Ill put a picture on how it looked like somewhere.......down here!
Well.I need help to fix this.URGENTLY.Thanks
Click to expand...
Click to collapse
Prerequisites :
Make sure you have samsung usb drivers installed,otherwise odin will not detect it,
then, try these steps :
1)Disconnect the wall charger first. reboot into download mode by long pressing Power button and Volume down buttons simultaneously for 8 to 10 seconds, then when you see "download" mode written,immediately press volume up button.
2) Download odin and download stock firmware from www.samsungupdates.com based on your region.
3) if you phone gets detected,odin textbox will turn green.
4) open odin, now check option " restart" make sure only this option is checked like the following screenshot attached.
5) now click on pda and naviagate to the stock firmware you have downloaded....
6) it will gonno take sometime,,,,,until you see a successful message in the bottom-left corner....
thats it. if you still run into any further issues,please let me know.
Well thanks for your help.The Tab is working again.Admins please lock.
c903jerk said:
Well thanks for your help.The Tab is working again.Admins please lock.
Click to expand...
Click to collapse
You are welcome buddy..

[Q] PLEASE HELP ME, Urgent :(

Hello,
I have Samsung Galaxy Note 10.1 ( Old version ) .
I got a problem with my device
I can`t turn it on anymore, when I hook it up with USB plug into ( PC ) or ( Power Adapter ) I got the following screen :
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
so I thought its not charged.
But then I left it to charge full ( 3 - 4 hours or maybe more ) but when I turn it on the welcome screen shows and stucked forever like following :
I tried to reset the factory and data and cache and everything inside BOOT list ( into "Power + Voulme up " menu ) but nothing happen too and the welcome screen still keep stucking .
What can I do ?
Some people told me I should put a new ROM/Software into it
But what is true ? and where is the problem ?
Please HELP !
I can't see any of the pictures you have put in your post. Have you tried reflashing your current rom onto your Note 10.1 with Odin? That usually fixes problems like this and it lets you keep your data.
link6155 said:
I can't see any of the pictures you have put in your post. Have you tried reflashing your current rom onto your Note 10.1 with Odin? That usually fixes problems like this and it lets you keep your data.
Click to expand...
Click to collapse
I am not familiar with Odin nor reflashing and stuff .
m4xst4r said:
I am not familiar with Odin nor reflashing and stuff .
Click to expand...
Click to collapse
1. Find the firmware for your device base on it's model number: http://www.sammobile.com/firmwares/
2. Download Odin onto your computer and run it.
3. Get your tablet and when it's turning on, hold the power button and volume down button until you get to the warning screen.
4. Press volume up to continue to download mode and plug your tablet into your computer via USB
5. On your computer, make sure Odin says "Added!". Load the firmware as a PDA into odin and press "Start". Do not unplug your tablet until the process has finish.
6. Android should begin to update and once that's done you should be good to go.

[How-To] Update your K10000 to Android 6.0

Hello guys since the android 6.0 update is out for this phone and many seemed to have issues upgrading it, i wrote down a guide on how to update it . Firstly there are two ways you can update your phone.
1) Via the wireless update app
2) Manually flashing the firmware
Steps:
1) Find the wireless update app on your phone and press check
2) You will be prompted to download the update file
3) Download.Install.Done.
If for some reason the first method does NOT work you can try this
1) Download the firmware file from here https://mega.nz/#!PQVWDaLZ!2ituEPLWpcAkbz9dR6dNk3E3rnl2z8YNELQ7xcYi7t0
2) Download the flash tool from here https://mega.nz/#!7AcjGCLY!5LtavmoUaz8N_GzRwJqhD9tWwRDapplAKu7TMmON7F4
3) Now open the flash tool by double clicking the SPMultiPortFlashDownloadProject.exe file
4) File -> Open Download Agent File and open this file MTK_AllInOne_DA.bin from this folder MDT_V1620_ForUpgrade
5) Click the button Scatter File and select the file MT6735M_Android_scatter which is located in
OUKITEL_K10000_V8.0_20160620 folder
6) Click Scan
7) Long press volume (+) key on your device (phone in power off state) and connect it to your PC. When green bar shows, scan successfully disconnect your phone.
8) Click Stop All and then Start All, when the small window finishes connect again your phone to the PC and the update will start automatically.
9) When the first line goes grey (COM 4 + COM 3) it means its completed.
Voila!
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
PS: Please let me know if i am allowed to post the download links, if not i will upload them as attachments here!
Thank you.
Bypass Google Account Problem with K10000
Hi
After auto-update my Oukitel K10000 asks for google account I do not have (I have tried every known to me email but nothing happend). I have read all internet, have seen a lot of films - nothing.
1.I cannot enter the developer option (to enable USB) because tapping the build number does not work - ANY sugestions? or step-by-step method
2.I cannot install Quick Shortcut Maker Apk in any mode.
PLEASE help
Flash tool is down.
Edit:
Found alternatives here http://spmdttool.com/category/download
v5 is buggy.

Categories

Resources