hi, just have my xperia z3 and i decided to flash and update my phone from kitkat to lollipop using flashtool. Unfortunately, I flashed the the wrong firmware (D6603, supposedly D6613). Now the phone does not turn ON, charging and hardly not recognized by the computer when connected ("USB unrecognized and malfunction"). I've tried different computers but still the same, I cannot flash the right firmware because it cannot be detected by the computer. Is there anyway or need to do to make it work. Please help, I appreciate any ideas you may share.:crying::crying:
Use PC Companion and repair your phone.
Thank you, I wanted to repair it using PCC but as I have said it cannot be detected by the computer. What is the problem? Please help... Pleeeeeaaassssssseeeeeeeeeeee:crying:
chie2x said:
Thank you, I wanted to repair it using PCC but as I have said it cannot be detected by the computer. What is the problem? Please help... Pleeeeeaaassssssseeeeeeeeeeee:crying:
Click to expand...
Click to collapse
Is this the same for you ?
What model is your phone?Is your bootloader unlocked/upgraded? What did you try?
Is your flashmod working? And flastboot? Light status, etc... ?
Related
Hi to all of you in this great site!!
I have xperia tipo(single) and after some working flash attempts with 2 custom firmwares... my phone ,i think,is totaly dead!!!!
No led no charge no screen no boot NOTHING!
I tried vol+-power etc... nothing
flashtool nothing -The device says:not connected in everywhere..
i have to say that I used for flash, dualboot.
The only think that i can see is when i connect the xperia usb in pc in device manager is"unknown device"
Also i have to say that the battery works ok.I test it in other tipo
Please help me to save my xperia tipo!!!!!
Thank you!
Possible it is hardbricked. Did you unlock bootloader?
If it is still locked, repair with pc companion, or give for service.
Sent from my ST27i
Tried to update to latest firmware using Sony bridge for Mac and about 10 minutes in, I got an error message and a failed update.
Phone now stuck in bootloop with message telling me update had failed please connect to computer and try again...... Mac won't recognise the phone now though.
Anyone got any ideas?
I've tried holding volume up and power buttons for 10 seconds and tried charging.... but the phone got really hot.
Anyone???
Sent from my SGP611 using XDA Premium HD app
Maybe you can install the latest Sony drivers over the net and plug the phone in again.... Kinda depends if USB debugging was turned of during the flash...
Do you have warranty?
If not... Are you familiar with ADB?
Sent From N5
Use a Windows PC. I have that problem too my Xperia Z3 is not detected on Sony Bridge... I think is a bug for the app.
Use SEUS or PC Companion and flash the firmware, Or download any Firmware for your model for Z3 and use flashtool (your Phone is not bricked only have a bad flash with flashtool you can fix it).
The phone is DETECTED on OS X but Sony Bridge not see the phone only that not be scary with Flashtool you can fix it or using Windows and PC Companion.
PS: Sorry if my english is bad xD.
PS2: If your phone revive download Android File transfer is better than Sony Bridge for file managing
Thanks for your quick replies. Much appreciated. I am having problems with my windows laptop but will try pc companion when I get it sorted.
Just one question. What is flash tool. I am not familiar with it sorry.
sjred_uk said:
Just one question. What is flash tool. I am not familiar with it sorry.
Click to expand...
Click to collapse
look for flashtool.net
use it to flash stock FTF's
Kindly Help me,
I was Flashing my Z3 by Flash Tool , i accidently select D6646 ftf file instead *of D6616 ftf , during flashing Flash Tool gives error at Kernal.sin and Phone goes Down,
No Soft or Hard Reset Work,
NO Flashmood / Fastboot Mood work ,
Flash Tool only Show
'Device connected with USB debugging off
19/021/2017 07:21:01 - INFO *- For 2011 devices line, be sure you are not in MTP mode
and Device Manager Shows SOMC Flash Drive,
When Connect By press Vol Down button and Attach USB Cable, USB not Recognized Error Shows*on Windows 7
I have TA backup from Flash Tool ( ie T1 and T2 ) before flashing in case of Partition break, where as
I realize its kernel brokeup
Kindly Plese Guide me what can I do to live my phone back
are you sure fastboot mode doesnt work? just power off and press vol+ and power if led is blue then you are is fastboot mode. then try to flash kernel.sin in adb command with pc . cheers
Yes sir sureonly red led show just for 2 3 sec n then goes off flash tool shows debugging mode off .. i disconnect battery to completly shut off phone after that i connect n same probelm
https://forum.xda-developers.com/showthread.php?t=2646405
xkeita said:
https://forum.xda-developers.com/showthread.php?t=2646405
Click to expand...
Click to collapse
ihad used that trick after whole day research , I can conclude S1tools does not support 2012 upgrade model, I received error as ID HASH IS NOT SUPPORTED,
however my bootloder is unlocked, and I hav unlocked code also, and also phone is rooted ,
Yes this could work for us as we still doesn't have the preloader dump.
AFAIK there is not unbricking way for now.
Somewhere I read that pc companion could work with Q9008. Also worth to try with emma.
I want working on this to finalize the unbricking guide but will not be soon as I need my device for the rom port. When done I will work on this unbricking.
Also it is not a kernel problem. Your flash replaced s1 bootloader with a wrong one.
Good luck a be patient
What about this: https://forum.xda-developers.com/showthread.php?t=1849170 ?
nailyk said:
Yes this could work for us as we still doesn't have the preloader dump.
AFAIK there is not unbricking way for now.
Somewhere I read that pc companion could work with Q9008. Also worth to try with emma.
I want working on this to finalize the unbricking guide but will not be soon as I need my device for the rom port. When done I will work on this unbricking.
Also it is not a kernel problem. Your flash replaced s1 bootloader with a wrong one.
Good luck a be patient
What about this: https://forum.xda-developers.com/showthread.php?t=1849170 ?
Click to expand...
Click to collapse
Thankq sir, for your reply so if its s1 bootloader then is it possible to bring my phone again live will u guide me what the next thing should i do
talharais said:
Thankq sir, for your reply so if its s1 bootloader then is it possible to bring my phone again live will u guide me what the next thing should i do
Click to expand...
Click to collapse
Sorry for confusing :s
I think, today, there is no way.
You can try with the official emma flash tool or pc companion but I really doubt.
nailyk said:
Sorry for confusing :s
I think, today, there is no way.
You can try with the official emma flash tool or pc companion but I really doubt.
Click to expand...
Click to collapse
Ohhh , sir i have TA backup still cant do anything and also charging also doesnot solve problem as mention in one of the xda thread
https://forum.xda-developers.com/showthread.php?t=1849170&page=1
talharais said:
Ohhh , sir i have TA backup still cant do anything and also charging also doesnot solve problem as mention in one of the xda thread
https://forum.xda-developers.com/showthread.php?t=1849170&page=1
Click to expand...
Click to collapse
Not related with TA backup for now. You change your bootloader with a wrong one.
It is almost like if you flash the wrong bios on your mother board. You can't flash it again until someone find an 'electronic' way.
Give a try with pc companion or emma.
nailyk said:
Not related with TA backup for now. You change your bootloader with a wrong one.
It is almost like if you flash the wrong bios on your mother board. You can't flash it again until someone find an 'electronic' way.
Give a try with pc companion or emma.
Click to expand...
Click to collapse
Pc companion is not reconize the fevice actually i explain what i idid,
I was flashing d6616 by flash tool
Firstly i unlock bootloder by sony , through unlock code they email then i rooted the device by kingo root n then flash accidently i chosse d6646 rom instead of d6616 rom then during flashing flashtool gives error at kernal.sin and after that device goesoff
When i plug into the pc it reconize my device as SOMC Flash device andflash tool gives dubugging off
Thats was the whole senrio by which my device brick so after whole story i really disappointed to know that my device is just use for paper weight... :crying:
I downloaded the emma after install it desnot show any usb device
You own a d6616? It have unlockable bootloader :s
Send it to repair center. No other choice.
And yes it is confusing, it say bootloader unlock after the fastboot command but it is not true.
@blackhawk_LA made some posts about D6616. Maybe he could help you.
I just post here to announce you the bad new your device is hardly softbricked.
nailyk said:
You own a d6616? It have unlockable bootloader :s
Send it to repair center. No other choice.
And yes it is confusing, it say bootloader unlock after the fastboot command but it is not true.
@blackhawk_LA made some posts about D6616. Maybe he could help you.
I just post here to announce you the bad new your device is hardly softbricked.
Click to expand...
Click to collapse
Service status shows unlock bootloader to yes.. well very thankful for you reply means there is no way to unbrick my phone
talharais said:
Service status shows unlock bootloader to yes.. well very thankful for you reply means there is no way to unbrick my phone
Click to expand...
Click to collapse
Keep an eye on https://forum.xda-developers.com/z3/devs-only/unbricking-d6603-t3365262
I just brick my device too so will try to make some progress on it
nailyk said:
Keep an eye on https://forum.xda-developers.com/z3/devs-only/unbricking-d6603-t3365262
I just brick my device too so will try to make some progress on it
Click to expand...
Click to collapse
Tanks buddy I am watching your thread, and also let me know when done,
Hi, I decided to post it here because it seems that anything I post on Xperia Ion forum is not read, it is inactive.
I already searched everywhere and I'm loosing my hopes. I'm trying to revive an Xperia Ion and this is what I get:
When I plug the phone in the wall charger the red led turns on for some minutes and then turns off.
The same happens when I plug on PC, when the led turns off it is detected as "Somc flash device" in windows device manager and this shows in flashtool:
INFO - Device connected with USB debugging off
INFO - For 2011 devices line, be sure you are not in MTP mode
Nothing changes if I plug in pc with volume + or - pressed, it don't goes into fastboot or flashmode.
I hope you could help me. Thanks
dude i have the same problem as yours i have a z3 d6643 and i made a mistake when downloading the kernal the device loads normal flash mode and flashtools working! power button + volume down runs twrp but it no longer starts at sony black screen someone please help!
evilhedrox said:
Hi, I decided to post it here because it seems that anything I post on Xperia Ion forum is not read, it is inactive.
I already searched everywhere and I'm loosing my hopes. I'm trying to revive an Xperia Ion and this is what I get:
When I plug the phone in the wall charger the red led turns on for some minutes and then turns off.
The same happens when I plug on PC, when the led turns off it is detected as "Somc flash device" in windows device manager and this shows in flashtool:
INFO - Device connected with USB debugging off
INFO - For 2011 devices line, be sure you are not in MTP mode
Nothing changes if I plug in pc with volume + or - pressed, it don't goes into fastboot or flashmode.
I hope you could help me. Thanks
Click to expand...
Click to collapse
Same problem with an XZ, someone has a solution?
sometime Win recognize the device as QUSB_BULK
Looks like I killed my Z5. The model is 6683 (Z5 dual), and I flashed with E6533 (Z3+ dual).
The phone is completely dead, cannot turn on, not vibrating on power button etc.
When I connect to my laptop, it says "unable to recognize USB device", in detail VID_0000&PID_0000.
But if I disconnect the battery, it recognized as "SOMC Flash device", VID_0FCE&PID_DDDE
Is it possible to resurrect it?
I hope if I can flash with correct bootloader in this state, it will enought to boot up and able to flash with the right firmware.
Macs1209 said:
Looks like I killed my Z5. The model is 6683 (Z5 dual), and I flashed with E6533 (Z3+ dual).
The phone is completely dead, cannot turn on, not vibrating on power button etc.
When I connect to my laptop, it says "unable to recognize USB device", in detail VID_0000&PID_0000.
But if I disconnect the battery, it recognized as "SOMC Flash device", VID_0FCE&PID_DDDE
Is it possible to resurrect it?
I hope if I can flash with correct bootloader in this state, it will enought to boot up and able to flash with the right firmware.
Click to expand...
Click to collapse
Are you able to connect it in flashmode and fastboot ?
With battery, no.
Without battery, my laptop recognize as "SOMC Flash device", but no tool can connect to it (like FlashTool).
(I think then different PID is the reason)
Macs1209 said:
With battery, no.
Without battery, my laptop recognize as "SOMC Flash device", but no tool can connect to it (like FlashTool).
(I think then different PID is the reason)
Click to expand...
Click to collapse
it seems to me that you are an advanced person in playing with your mobile, this kind of issues is beyond of my knowledge but I was replying to your thread hopefully someone here can help, I'm fearing that you have messed up with your mobile
Well, you could try to flash it from Ubuntu (NOT inside Windows 10 !) via FlashTool,
under windows there are limitations with different device IDs that separate drivers would be needed (and if only "wrong" ID is detected under Linux it doesn't really matter, since it's detected anyway),
perhaps under Linux operating systems you have more luck
Thank you for idea, but not working.
Finally I found an old SETool3 box , and successfully flashed with it without battery
Somehow it can fixed it.
Macs1209 said:
Thank you for idea, but not working.
Finally I found an old SETool3 box , and successfully flashed with it without battery
Somehow it can fixed it.
Click to expand...
Click to collapse
I am facing a similar situation, can you help me by telling me what exactly did you do to solve the issue step by step?
Same Problem With Me PLZ HELP
Dear Bro Ive same problem with my Xperia e6683 Total Dead After Wrong Flash with Xperia Z3+ File... SO Plz help me how to fit step by step guide plz....
As on 20 Jan 2017
I've Flash Successfully It With Setool fusion Box Without Battery Use Test Pin Method. Now My My Phone Again Alive..
[email protected] said:
Dear Bro Ive same problem with my Xperia e6683 Total Dead After Wrong Flash with Xperia Z3+ File... SO Plz help me how to fit step by step guide plz....
As on 20 Jan 2017
I've Flash Successfully It With Setool fusion Box Without Battery Use Test Pin Method. Now My My Phone Again Alive..
Click to expand...
Click to collapse
Dear Bro Ive same problem with my Xperia x Total Dead After Wrong Flash
The phone is completely dead, cannot turn on, not vibrating on power button etc.
When I connect to my laptop, it says "unable to recognize USB device"
using test pin method it is recognized as "SOMC Flash device"
i have backup ta partition and ftf firmware of my xperia i can't find any tool to flash
can you guide me please
Flashtool Doesn't Recognise This Device. U can use Setool/ Setool Fusion Box to Repai
bma1973 said:
Dear Bro Ive same problem with my Xperia x Total Dead After Wrong Flash
The phone is completely dead, cannot turn on, not vibrating on power button etc.
When I connect to my laptop, it says "unable to recognize USB device"
using test pin method it is recognized as "SOMC Flash device"
i have backup ta partition and ftf firmware of my xperia i can't find any tool to flash
can you guide me please
Click to expand...
Click to collapse
Bro
In this Condition Flashtool Not Recognised Ur Device. There is only a best solution U Can Use SETOOL/SETOOL FUSION BOX To Repair/ Flash Ur Device.
[email protected] said:
Dear Bro Ive same problem with my Xperia e6683 Total Dead After Wrong Flash with Xperia Z3+ File... SO Plz help me how to fit step by step guide plz....
As on 20 Jan 2017
I've Flash Successfully It With Setool fusion Box Without Battery Use Test Pin Method. Now My My Phone Again Alive..
Click to expand...
Click to collapse
bma1973 said:
Dear Bro Ive same problem with my Xperia x Total Dead After Wrong Flash
The phone is completely dead, cannot turn on, not vibrating on power button etc.
When I connect to my laptop, it says "unable to recognize USB device"
using test pin method it is recognized as "SOMC Flash device"
i have backup ta partition and ftf firmware of my xperia i can't find any tool to flash
can you guide me please
Click to expand...
Click to collapse
wrong flash means wrong kernel!
you might be stuck on black screen when you frist switchon device! the device is running! but since its stuck on bootloops no interface is open!
press power and volume up button for 15+ seconds and let it JERK 3 times , this if force shutdown. the device should get connected now in flashmode
Hi, my phone is dead (I think)...
No flashmode/fastboot, no boot, no any led after connecting to pc or anywhere (but pc show unrecognized device- LOL)
Device not recognized
Is there a way to fix it?
Someone help?:crying:
lets solve together
ok
submit post:fingers-crossed:
sbairayen2 said:
Hi, my phone is dead (I think)...
No flashmode/fastboot, no boot, no any led after connecting to pc or anywhere (but pc show unrecognized device- LOL)
Device not recognized
Is there a way to fix it?
Someone help?:crying:
lets solve together
ok
submit post:fingers-crossed:
Click to expand...
Click to collapse
Give us some further information. Was your bootloader unlocked? What was the last thing you did before it died?
Did you try to charge it using the wall plug?
St.Jimmy90 said:
Give us some further information. Was your bootloader unlocked? What was the last thing you did before it died?
Did you try to charge it using the wall plug?
Click to expand...
Click to collapse
It sounds to me like youve tried to flash it without the Google "flashmode" & "Fastboot" drivers installed and / or youve tried to use flashtool... instead of NewFlasher
Have you tried a "Repair" using Sony Companion?
As said above... we need more info..
Have you fixed your xz premium
Same as me.
My z5 died 2 years ago when flashing kernel from flashtool and pc turned off when flashing,
when flashing the kernel is not flashed flashed yill the end and i got anonymus driver when turning on pc and connectiong my phone.
Now no led and no boot and nothing.
Unrecognised driver.
thinking about selling my rooted xzpremium (dual sim). PM if you're interested in buying it.
Try Emma