Hello,
Simple question...
not wifi will not send imei info
but in teory the mac address is also enuiq
Thanks for the reply...
I just got told from a custmer service person that if the IMEI number is blocked it will also stop it from even been turned onto its factory 'pda' mode to access details without a sim card!??
This phone is a Jasjam.
Can you make an emergency call without a SIM card? if so, chances are the IMEI is sent over while connected for emergency call. Howeve, I would guess that may probably on the other side of the network where not much attention is paid there.
I don't believe customer services on technical questions like.. 70% of the time. Some of they are just crap. From what I can think of, if your IMEI is blocked, you can still use the PDA as a PDA. There is a case here.. one of the thread.. where a guy found (as it lost by someone) a phone on block IMEI.. then used is as PDA (he cheekily ask if he can change his IMEI). Probably he got your phone?
N00B here! but tried to gather as much info as I could..
Got a VZW droid 2 global from ebay that the seller profiled as "unlocked"
I'm in Central America and trying to register it with a GSM 850/1900 carrier but it won't connect to the network at all.
It had a 14 IMEI code... found it's translation to 15 to 17 IMEI and bought a the unlock code on a site. I got the unlock code but the phone has nowhere to enter it.
Found a post stating that it should ask for the code after inserting a foreign sim card or waiting 30 minutes if nothing happens. tried that and there's no prompt.
I have accessed the testing menu with *#*#4636#*#* and select the GSM only and WCDMA preferred (I got an HTC Inspire 4G working with that one here) and it is recognizing the GSM 850/1900 local carriers but unable to get any network access from them.
Found that VZW locks the carrier's network ids but the phone is recognizing them.
Again: ir recognizes the networks but is not asking for an unlock code... all the posts states to enter the code but they don't say how (the phone must prompt it automatically)
Please let me know if there is any way to manually pull up the field to enter the unlock code or if I can try anything else to unlock it
Thanks!
First, the phone's IMEI is written on the label under the battery.
Second, if you switch it to GSM mode it will output the IMEI in *#06# and in Settings, About phone, Status.
The 14 digit code you mentioned is probably MEID in hex form.
Switching to GSM is done by going to Settings, Wireless & networks, Mobile networks, Network Mode.
Using the service menu you mentioned is wrong and can lead to the phone being unable to connect to GSM at all, in which case you must reflash the SBF.
Actually I got the unlock code but there is nowhere to enter it.
Also it allowed to me to at least view the available networks after changing it to GSM/WCDMA and seems to be trying to connect to one but there's no signal at all.
If I do a network search now it will show me the available networks 5 or 6 (2G&3G), selected one and it just shows that it is not able to connect to that network
BTW, found that the radio was off as well and had to switch it on using the testing menu because by going to Settings, Wireless & networks, Mobile networks didn't allow me to access it at all, it was just grayed out and there was no way I could turn on the radio using that option..... sorry... I think I got everything I need except where to enter the unlock code
It looks like you have successfully (like other people before you) fried the GSM radio settings. Congratulations.
You need to flash the SBF to reset the phone's radio module to its original state.
If you actually bought a phone that was already unlocked it won't ask for an unlock code.
A locked phone asks for the code the moment you power it on and let it boot with a non-Verizon SIM card.
The code you supposedly bought is not for your phone at all, because you requested it for an IMEI you made yourself from something that was never an IMEI.
For me, The unlock screen appear only on original rom with non-verizon sim.
not appear on custom rom.
Having an issue with a newly picked up at&t P907a and looking for a little help.
Love the note pro but when I add a sim the pro recognizes that it has been inserted and a pop up asks to be restarted to connect to the network.
Once restarted it simply says 'no sim installed' and won't let me into the mobile networks part of the android settings to change any networks etc..
Running stock at&t as it has been factory reset.
I've been assured this pro is unlocked but starting to have my suspicious...
Anyone else come up against this?
Thanks.
Call AT&T or go on their website and do live chat, they will look up the IMEI and can unlock it for you.
https://www.att.com/deviceunlock
Thanks Jargin,
So the issue I'm having is because the pro is not unlocked? Have you had the same issue with it saying no Sim installed?
I've been told that if you put in an unsupported Sim in one it will ask for an unlock code rather than just displaying no sim..
No after reboot my device asked for an unlock code. I would take it to a store, maybe someone entered too many won't pin codes, that can happen too.
I got the Chinese version of the phone and I put my SIM from my carrier UQ. It detects the APN settings and all the info is correct. It connects to the network, but the phone number doesn't seem to be working.
It won't receive mms messages or phone calls.
When I try to type in my phone number to register my phone for the Hey Tap service the area code get auto input, but as the wrong area code. Japan is +81, but it keeps recognizing my number as +86.
Anyone know what the deal with the phone number is?
A am in russia and i have chinese version too.
I register my heytap account with pc, in pc browser you can write any tltphone code, and later just write you id, and phone and youcan recive confirmation sms. use this link https://id.heytap.com/index.html to doit.
Hey, thanks for the reply.
I did use that site on my PC to register, and it accepted my Japanese number. I could register and create an account.
But still on my Find X2 Pro my SIM cards gives me an error when I enter the phone app and click on "carrier > additional settings".
I still cant receive calls or sms. I have no idea whats wrong. My mobile data connects and I can use the internet without problem. Just my number does not seem to connect.
Any help please.
Try other sim card, maybe problem with you sim or carrier.
I solved the problem.
UQ SIM network is not compatible with Chinese Find X2 Pro.
I changed to Y!Mobile and all is working perfectly.
Hi all. I just bought a S10e (G970U, Snapdragon) from China in order to use it in Spain, with Orange as a carrier. Once I set it up, everything worked fine for about 20 seconds. After that, the mobile data locked down. When I try to turn it up again the device says: "Security policy prevents use of mobile data". I tried to factory reset it several times, try different google accounts, try different SIMs, erase the data from some SIM- and network-related apps, but nothing changes. I guess that this has something to do with Samsung Knox.
What should I do? Is recommendable to contact Samsung support? Can I flash another firmware/ROM that fix this issue? Thanks a lot, any help is appreciated.
PS: Calls and SMS are also locked.
@txordi
Maybe this will help?
https://www.samsung.com/nz/support/mobile-devices/security-policy-updates/
djg269 said:
@txordi
Maybe this will help?
https://www.samsung.com/nz/support/mobile-devices/security-policy-updates/
Click to expand...
Click to collapse
Hi. Thanks a lot for your help! I tried it and nothing changed. Indeed, the security policies were already updated out of the box...
I had the same problem. I had a signal but could not send/receive SMS or calls. After talking with carrier tech support and Samsung, I went to a UbreakIfix store, where they told me the 10e phones have a problem with the antenna on the motherboard. They said I needed to send the phone back to Samsung to get the mobo replaced. I just sent it back to the seller and bought an S20.
Also on S10+
I'm having the same problem on my GM-975U1 S10+. Basically mobile data and texting works long enough to authenticate into the Samsung account during setup, but once the android home screen appears after finishing the setup I can't place any calls and trying to enable mobile data gives a "Security policy prevents use of mobile data" error when attempting to enable it. Neither AT&T or Samsung have given instructions on how this can be fixed. It's behaving similarly to if the phone's IMEI were on a blacklist, but I get immediately shut out once the setup process completes.
kriegersaurusrex said:
I'm having the same problem on my GM-975U1 S10+. Basically mobile data and texting works long enough to authenticate into the Samsung account during setup, but once the android home screen appears after finishing the setup I can't place any calls and trying to enable mobile data gives a "Security policy prevents use of mobile data" error when attempting to enable it. Neither AT&T or Samsung have given instructions on how this can be fixed. It's behaving similarly to if the phone's IMEI were on a blacklist, but I get immediately shut out once the setup process completes.
Click to expand...
Click to collapse
have you found any solution yet I am having same issue with my samsung s10e and I don't even understand what app or policy is preventing me from making calls. BTW I am using clean esn phone. As soon as I pass the setup screen LTE signal goes away and it stops working.
aakashpsp said:
have you found any solution yet I am having same issue with my samsung s10e and I don't even understand what app or policy is preventing me from making calls. BTW I am using clean esn phone. As soon as I pass the setup screen LTE signal goes away and it stops working.
Click to expand...
Click to collapse
I haven't found one yet either. Apparently the phone I purchased is locked to Tracphone after paying for an IMEI lookup (got scammed by an ebay seller who said it was the unlocked model), and the phone isn't able to do calls/mobile data properly except during the initial setup. Tried with SIM cards from two different US providers that both aren't working on it, and can connect to wifi just fine. Can see in the phone information test menu by dialing *#*#4636#*#* that my sim is being recognized, shows my phone number and IMSI, can switch between network types and see the cell towers it connects to; but isn't able to send/receive calls or mobile data. It fails the Ping test with 'Fail(2)' and HTTP Client Test with 'Fail: IOException'.
It's also showing that the phone receives a call inside of the Service Mode menu by dialing *#197328640# and going to '[1] BASIC INFORMATION'. Placing a call from another phone shows that my S10+ is picking up LTE bands and has some RF parameters that change when my number is being dialed, but don't get the option to pick up the call. It's also able to detect that I have a voicemail but am not able to dial in and listen to it. The Tx Pwr says '-- dBm' so I ultimately can't tell if it's a software or a hardware problem.
kriegersaurusrex said:
I haven't found one yet either. Apparently the phone I purchased is locked to Tracphone after paying for an IMEI lookup (got scammed by an ebay seller who said it was the unlocked model), and the phone isn't able to do calls/mobile data properly except during the initial setup. Tried with SIM cards from two different US providers that both aren't working on it, and can connect to wifi just fine. Can see in the phone information test menu by dialing *#*#4636#*#* that my sim is being recognized, shows my phone number and IMSI, can switch between network types and see the cell towers it connects to; but isn't able to send/receive calls or mobile data. It fails the Ping test with 'Fail(2)' and HTTP Client Test with 'Fail: IOException'.
It's also showing that the phone receives a call inside of the Service Mode menu by dialing *#197328640# and going to '[1] BASIC INFORMATION'. Placing a call from another phone shows that my S10+ is picking up LTE bands and has some RF parameters that change when my number is being dialed, but don't get the option to pick up the call. It's also able to detect that I have a voicemail but am not able to dial in and listen to it. The Tx Pwr says '-- dBm' so I ultimately can't tell if it's a software or a hardware problem.
Click to expand...
Click to collapse
I am facing the same exact issue my sim number it shows inside the phone and signal I am getting is in negative dbm also my sim receives calls during the initial setup and as soon as the setup completes the LTE network goes away call gives error " call not sent". I am irritated by this now and there is no root available for this model so I cannot flash any custom rom to check. I have seen many people have same issue but no solution yet.
If your phone locked to a particular network, ie TracFone,AT&T, TMobile, Cricket, etc, then that is only network it will work on. Doesn't matter what custom ROM you use. You will need to get the network unlock code either from the network it's locked to or from a reputable online unlock site. Good luck getting it unlocked.
riggerman0421 said:
If your phone locked to a particular network, ie TracFone,AT&T, TMobile, Cricket, etc, then that is only network it will work on. Doesn't matter what custom ROM you use. You will need to get the network unlock code either from the network it's locked to or from a reputable online unlock site. Good luck getting it unlocked.
Click to expand...
Click to collapse
my device is already unlocked. It is not an unlocked phone issue. This is some stupid policy which is preventing from making calls or using data. Maybe this policy is saved in EFS don't know.
aakashpsp said:
my device is already unlocked. It is not an unlocked phone issue. This is some stupid policy which is preventing from making calls or using data. Maybe this policy is saved in EFS don't know.
Click to expand...
Click to collapse
That's strange, it's acting exactly like a network locked device. When you say it's unlocked, are referring to the bootloader or network? Did you buy it new, unlocked from a reputable dealer? Check the firmware and make sure it is unlocked. There are other thread here with the same issue and message, those are all network locked phones.
riggerman0421 said:
That's strange, it's acting exactly like a network locked device. When you say it's unlocked, are referring to the bootloader or network? Did you buy it new, unlocked from a reputable dealer? Check the firmware and make sure it is unlocked. There are other thread here with the same issue and message, those are all network locked phones.
Click to expand...
Click to collapse
I don't know I bought it from mercari that seller told me it is tmobile unlocked, but while checking I found the model number is G970U1. csc is XAA and binary U4. Bootloader is locked. Networks seems to be unlocked as when I put it my sim card it works till initial setup screen and then stops working. I searched it maybe locked to Consumercellular but is there any way I can unlock it ? I didn't find anything online.
Sounds like the seller lied to you.
Is there any way to unlock CC device ? I am on Binary u4. I am able to flash both g970u and g970u1 firmware but no success.
riggerman0421 said:
That's strange, it's acting exactly like a network locked device. When you say it's unlocked, are referring to the bootloader or network? Did you buy it new, unlocked from a reputable dealer? Check the firmware and make sure it is unlocked. There are other thread here with the same issue and message, those are all network locked phones.
Click to expand...
Click to collapse
My S10+ model G975U is network unlocked, with the bootloader locked. I bought a network unlock code, but am getting the same behavior where the intial setup allows me to sign into my Samsung account when putting in both an ATT and T-Mobile sim card. I've also tried reflashing it with several different firmwares both carrier locked and unlocked, but this phone has been sitting in my drawer for the past month since it's unusable. Probably will end up trading it in since I was scammed by the random ebay seller I bought this from.
kriegersaurusrex said:
My S10+ model G975U is network unlocked, with the bootloader locked. I bought a network unlock code, but am getting the same behavior where the intial setup allows me to sign into my Samsung account when putting in both an ATT and T-Mobile sim card. I've also tried reflashing it with several different firmwares both carrier locked and unlocked, but this phone has been sitting in my drawer for the past month since it's unusable. Probably will end up trading it in since I was scammed by the random ebay seller I bought this from.
Click to expand...
Click to collapse
I'm having the exact same issue. Bought s10+ off ebay for 200 locked to consumer cellular. Bought an unlock code. It said unlock successful. Now get this error with any sim. It will show lte during initial setup only.
It will show that it's at&t or verizon when I put the sim in and populate the proper apn settings.
Before the unlock I would get the sim not provisioned error.
I did have to look up the dial code to make the unlock code window appear.
Now i can't actually use any service and i get the security policy error.
Finally was able to find the xaa firmware which seems to be the exact firmware on it.
Then lash that as no other u1 firmware would flash.
txordi said:
Hi all. I just bought a S10e (G970U, Snapdragon) from China in order to use it in Spain, with Orange as a carrier. Once I set it up, everything worked fine for about 20 seconds. After that, the mobile data locked down. When I try to turn it up again the device says: "Security policy prevents use of mobile data". I tried to factory reset it several times, try different google accounts, try different SIMs, erase the data from some SIM- and network-related apps, but nothing changes. I guess that this has something to do with Samsung Knox.
What should I do? Is recommendable to contact Samsung support? Can I flash another firmware/ROM that fix this issue? Thanks a lot, any help is appreciated.
PS: Calls and SMS are also locked.
Click to expand...
Click to collapse
I'm from the Philippines and my niece phone is network lock ( Smart Telecom ) I can use the sim 2 slot since it's a dual sim using another network Simcard, unfortunately, it won't allow me to use mobile data so I tried unlocking it *#272*IMEI FROM SIM 1 SLOT# so I choose GLB for globe network or XTC to openline so here's what happens, it got reset so upon set up yeah other sim works have data but when finish setting up everything I can use data again on other network and a message pop up
Security policy prevents use of mobile data
so I guess even it allows other network Simcard on network lock phone it needs to be unlocked by the network where it was lock
Did anyone ever find a solution to this problem?
I'm having the exact same problem with a new samsung s10e I just bought. Security policy prevents use of mobile data, and no calls or sms will go through. LTE shows on setup, but disappears as soon as setup is complete.
I initially assumed the phone was locked, but the seller is reputable and insists it is unlocked. It's also a U1 model, and an IMEI lookup appears to show that it's unlocked. In connection settings under mobile networks, i'm also able to select multiple carriers, so I'm inclined to believe that the device really is unlocked.
Anybody here ever manage to solve this problem, or am I SOL? I would hate to be out 200 bucks on this phone since i'm past the return window.
I am having same isuue with samsung not S20 ultra (SM-N986U1) I bought the mobile and its unlocked the seller send to me photo for the check screen and its open USA but can not use mobile data and make any calls when a make a call the call ended and give me screen call not sent
aniratepanda said:
Did anyone ever find a solution to this problem?
I'm having the exact same problem with a new samsung s10e I just bought. Security policy prevents use of mobile data, and no calls or sms will go through. LTE shows on setup, but disappears as soon as setup is complete.
I initially assumed the phone was locked, but the seller is reputable and insists it is unlocked. It's also a U1 model, and an IMEI lookup appears to show that it's unlocked. In connection settings under mobile networks, i'm also able to select multiple carriers, so I'm inclined to believe that the device really is unlocked.
Anybody here ever manage to solve this problem, or am I SOL? I would hate to be out 200 bucks on this phone since i'm past the return window.
Click to expand...
Click to collapse
esca91 said:
Hello everybody,
Could you share firmware of Sm-r900 ?
Thanls All for good work !
Bests regards.
Click to expand...
Click to collapse
mosaad627 said:
I am having same isuue with samsung not S20 ultra (SM-N986U1) I bought the mobile and its unlocked the seller send to me photo for the check screen and its open USA but can not use mobile data and make any calls when a make a call the call ended and give me screen call not sent
Click to expand...
Click to collapse
Yes, there is a solution, but only from an experienced professional 3rd party business, which means there's no free solution