My device is D6603, already rooted in kitkat using giefroot, locked bootloader, "Z3-lockeddualrecovery2.8.15" installed.
I flashed the " D6603_23.1.A.1.28_Customized_NCB" firmware as "[D66XX]{5.0.2} Flashable stock Lollipop pre-rooted collection & XZ dualrecovery" post instruct, after that, the device restart, and I enjoyed lollipop for just a few minutes, after I open the Setting, the device first become no response, then screen is off, led off(even plug into adapter), no response no matter how hard i tried to press the power button, with vol+/- pressed together, no response at all!!
After one night leave it alone, i tried again, no response at all ,however, when i plugged into adapter, the led light became red, then after a while, it began to blink in red.
Please help me, what should i do with this condition?
mythomasy said:
My device is D6603, already rooted in kitkat using giefroot, locked bootloader, "Z3-lockeddualrecovery2.8.15" installed.
I flashed the " D6603_23.1.A.1.28_Customized_NCB" firmware as "[D66XX]{5.0.2} Flashable stock Lollipop pre-rooted collection & XZ dualrecovery" post instruct, after that, the device restart, and I enjoyed lollipop for just a few minutes, after I open the Setting, the device first become no response, then screen is off, led off(even plug into adapter), no response no matter how hard i tried to press the power button, with vol+/- pressed together, no response at all!!
After one night leave it alone, i tried again, no response at all ,however, when i plugged into adapter, the led light became red, then after a while, it began to blink in red.
Please help me, what should i do with this condition?
Click to expand...
Click to collapse
You should reinstall your firmware using Sony PC companion. Download it and it will give you instructions how to repair your phone. Make sure you have all the necessary drivers installed. this is official and simple method to repair your phone
Secondly , you can alternatively use FLASHTOOL.
If you still have questions, quote for a reply
Hnk1 said:
You should reinstall your firmware using Sony PC companion. Download it and it will give you instructions how to repair your phone. Make sure you have all the necessary drivers installed. this is official and simple method to repair your phone
Secondly , you can alternatively use FLASHTOOL.
If you still have questions, quote for a reply
Click to expand...
Click to collapse
my phone is still bricked. when using flashtool in flashmode, connected to the PC, it repeats the following message:
INFO - For 2011 devices line, be sure you are not in MTP mode
INFO - Device disconnected
Device connected with USB debugging off
For 2011 devices line, be sure you are not in MTP mode
INFO - Device disconnected
and the led light is red on, then off, then on ....
if i try to connect it to the power adapter, the led light is red with fast blink. And I try to use another power adapter (iphone's ), the red light is on, continuously for about 20 minutes, then off, at this time ,if i try to reconnect to the power adapter, the led is still off. after try power button or vol+ button, then the led is back again , but with the same status.
is there anything I can do with my z3? I'm desperate...
thanks a lot !!
mythomasy said:
my phone is still bricked. when using flashtool in flashmode, connected to the PC, it repeats the following message:
INFO - For 2011 devices line, be sure you are not in MTP mode
INFO - Device disconnected
Device connected with USB debugging off
For 2011 devices line, be sure you are not in MTP mode
INFO - Device disconnected
and the led light is red on, then off, then on ....
if i try to connect it to the power adapter, the led light is red with fast blink. And I try to use another power adapter (iphone's ), the red light is on, continuously for about 20 minutes, then off, at this time ,if i try to reconnect to the power adapter, the led is still off. after try power button or vol+ button, then the led is back again , but with the same status.
is there anything I can do with my z3? I'm desperate...
thanks a lot !!
Click to expand...
Click to collapse
did you hold the Vol+ button when inserting the microusb? Also, the device must be completely off (power+vol+)
mythomasy said:
my phone is still bricked. when using flashtool in flashmode, connected to the PC, it repeats the following message:
thanks a lot !!
Click to expand...
Click to collapse
turn off your device.
Hold power+volume up button and then connect your device via a USB. If however, the device disconnects, you should keep holding the power button and do not leave it.
Lastly, upgrade your drivers from flashtool folder!
Good Luck
Incanity said:
did you hold the Vol+ button when inserting the microusb? Also, the device must be completely off (power+vol+)
Click to expand...
Click to collapse
you mean inserting the microusb connected with power adapter using vol+button? I tried ,but the led light still fast blinking in red.
I thought maybe the fast blinking means the phone cannot charge in.
Hnk1 said:
turn off your device.
Hold power+volume up button and then connect your device via a USB. If however, the device disconnects, you should keep holding the power button and do not leave it.
Lastly, upgrade your drivers from flashtool folder!
Good Luck
Click to expand...
Click to collapse
i hold the power button and vol+ button with rubber bang, connect to power adapter, however, no led light on!
mythomasy said:
i hold the power button and vol+ button with rubber bang, connect to power adapter, however, no led light on!
Click to expand...
Click to collapse
Do this , Make sure you load all the files in flashtool and it is waiting for the device.
When it is waiting to flash, hold down power+volume key and connect it. Connecting before means, you will have to hold it for a long time
If it doesnot work, your drivers are outdated which as i suggested upgrade from flashtool folder
mythomasy said:
i hold the power button and vol+ button with rubber bang, connect to power adapter, however, no led light on!
Click to expand...
Click to collapse
no;
when NOT connected: press power + vol+. After that you get two vibrations from the device, this means the device is off.
after that, hold ONLY vol+, and connect it to your PC, with Flashtool waiting for the device using flashmode.
the device will never vibrate, no response at all!
I went to customer service yesterday, they said my device is completely no response to any test and need to change the mainboard....how could a basically flash(just flash 5.0.1 with bootloader never unlocked) will result in such a disaster?! I cannot understand!!
I was in fastboot mode ready to unlock my bootloader, the phone got the led in a blue color when suddenly the led turned off.
I dont know what happenden but the phone looks dead.
The screen its black and the led its off, i got no reaction to anything except when i connect the phone to my pc, the pc tells me its an unkown device. help please.
I allready tryied the volume up and power button and also i tryied to get again in fastboot mode but it doesnt work.
Chacho3993 said:
I was in fastboot mode ready to unlock my bootloader, the phone got the led in a blue color when suddenly the led turned off.
I dont know what happenden but the phone looks dead.
The screen its black and the led its off, i got no reaction to anything except when i connect the phone to my pc, the pc tells me its an unkown device. help please.
I allready tryied the volume up and power button and also i tryied to get again in fastboot mode but it doesnt work.
Click to expand...
Click to collapse
try to put it on charge by plug in to a normal electric socket and check the device reaction.
If you get positive reaction which means LED ON , or battery recharge etc then you are good to go in to the next level which means...
Plug your device in to your PC/laptop. If it gets again with "not recognizing" try different USB port.
If all the ports showing you the same problem, try to find another cable. If you get again the same problem try to find another PC to test if there is recognizable.
these are the first steps you should so before i suggest you anything else. We have to make sure that your device is in a working state.
I have a Lg G Pro 2. Few days back it got bricked by its own( a crazy fact). That time it was showing QHSUSB_BULK. I figured it out as 9006. Took the phone to a local service shop. Today I got it back and found that nothing had happened to the phone, except worse. Now it is not detected by PC, only green light blinks for some time if tried to power on. And then everything is black and cold as death.
I think it have been flashed with wrong ROM. Anybody here can guide me with the test points of Lg G Pro 2 (D838 F350) ? So that I can force it to QHSUSB_BULK ? Or any step by step advice to get it up ?
I am in real need of assistance, and thanks in advance for any sort of help. Best Regards.
I would like to mention that the phone indicator blinks for sometime if I try to power it on, as it does on boot, but nothing else is there. No recognition by PC, no presence in Device Manager. Blinks for sometime, stops, again starts blinking... and this goes on at regular short intervals. The area around the camera gets warm after sometime. Everything loops till I pull off battery.
Now, am I missing something ? Is the problem not as deadly as I am thinking ? Is it soft bricked ?
Hi, I not sure how it got bricked I never brick LG device.
Normally if anything happen we try pull battery out and put it back in, try then to turn the phone on.
Have you try connect to to pc with USB cable, one end of USB connnect to pc and other end connect to the phone. Then try press Power + Volume Up or Power + Volume down, this is to try to get into phone download mode. If you can get into download mode you can flash the kdz file to make it useable again.
Or without the USB cable we want to get to factory reset mode by use hardware method try press:
- Power + Volume Up or Power + Volume down
- If you see LG logo come up release the buttons you press above 1-2 second
- Press again Power + Volume Up or Power + Volume down
- Until it show and ask to use volume up/down button to select choice, say yes
Caution factory reset will delete all data on the phone and reset it as when you bought it new.
- Again it will ask for factory reset, use Volume up/down to choose and select yes for factory reset
turn on the phone and when light is blink press volume up or down button for some time and see if it it is detected as usbhulq?
Hello everyone
Please help me
I have a Sony Xperia Z3 Dual D6633 with Android 4.4.4
Firmware is D6633_23.0.F.1.74_CE
I tried to install TWRP on my phone using this tutorial
https://forum.xda-developers.com/z3/development/root-stock-kernel-twrp-v01-test-28-09-t2889794?__utma=248941774.950623471.1412017766.1412017766.1412017766.1&__utmb=248941774.1.10.1412017766&__utmc=248941774&__utmx=-&__utmz=248941774.1412017766.1.1.utmcsr=l.facebook.com%7Cutmccn=(referral)%7Cutmcmd=referral%7Cutmcct=/lsr.php&__utmv=-&__utmk=228295838
Since the links in the thread are down it was hard for me to get the bootZ3dualmonxtest01.img file
But after an hour of googleing finally I got it from another Android forum https://mdforum.ru/showthread.php?t=16534
Then, as mentioned in the tutorial I went into bootloader / fastboot mode and entered following command
fastboot flash boot bootZ3dualmonxtest01.img
But it didn't work. Now my phone is bricked. It's powered off and I can't turn it on again
It doesn't respond to anything
Pressing Powerbutton - Nothing
Pressing Power + Volume Up/Down - Nothing
Hold Volume down and connect to PC - Nothing
Connect to 230V Adapter for charging - Nothing
ADB doesn't recognize the phone
Flashtool responds "Device disconnected"
So I can't flash back stock ROM
Please help me out. What went wrong? How can I fix it? Is it repairable or is my phone hard bricked?
Thank you for your answers
Edit:
After several hours of googleing and trying I found a solution that worked for me
Great thanks to StuartjG who posted the steps in this thread
https://forum.xda-developers.com/z3/help/z3-matter-t2945910/post61412021#post61412021
If someone else hase a similar problem this is what worked for me:
StuartjG said:
My Z3 would not power up and no charge LED when cable plugged in. Finally found this solution on Sonymobile support website which fixed my phone!
To force the device to restart
Detach the SIM card slot cover.
Using the tip of a pen or similar object, press and hold down the small OFF button (generally indicated by the text "OFF") until the device has emitted three vibrations, and then release the OFF button. The device turns off automatically.
Charge the device until a charging icon appears on the screen.
Turn on your Xperia™ device.
If a forced restart procedure as described above doesn't succeed in turning on your device, you should try another kind of forced restart - the 2-minute restart procedure.
To force a 2-minute restart
Detach the SIM card slot cover.
Using the tip of a pen or similar object, press and hold down the small OFF button (generally indicated by the text "OFF") for 120 seconds (ignoring any vibrations), and then release the OFF button.
Charge the device until a charging icon appears on the screen.
Turn on your Xperia™ device.
I had to hold the 'off' button for about 60 seconds before the phone vibrated and sprung into life - phew!
Click to expand...
Click to collapse
In my case there were no vibrations. I just held the button down for 120sec and it worked. Then I was able to flash back stock ROM
D2206. Got into a bootloop (the phone only shows the Sony and Xperia logo but ain't starting the system and just restarting forever doing it again and again). Can't get into Fastboot mode because volume buttons and power button isn't reacting at all. The only solution to force it to show some traces of life is plug him to PC or to a charging device but nothing happens except the charging lightning animation appears. And after connecting to PC, it seems like Flashtool recognize him, but nothing can be done because of the periodic 5-7 second interval disconnects.
Any solutions or tips?
You need to power off before connecting. Here's how.
I don't know if you figured this out or still need the help now, but I'm answering because it's the one thing here that I do know the answer to.
From your description, it sounds like you are trying to connect your phone to PC while the phone is still in boot loop. This will not work. You need to power it off first. Since your power and volume buttons won't respond during boot loop, you will need to use the hardware override that is provided.
Under the back panel of your phone, between the SIM2 and microSD slots, you will see a small punch-hole about 2 mm in diameter and labelled "OFF." Use a pen or precision screwdriver to gently press the off switch located inside this punch-hole for about 1 sec. Phone should switch off.
Wait about 15 sec before connecting to PC in Flash (Vol Up pressed down) or Fastboot (Vol Down pressed down) mode until the LED flashes the respective colour and then you can follow whatever instructions you are following.