I have a Lg G Pro 2. Few days back it got bricked by its own( a crazy fact). That time it was showing QHSUSB_BULK. I figured it out as 9006. Took the phone to a local service shop. Today I got it back and found that nothing had happened to the phone, except worse. Now it is not detected by PC, only green light blinks for some time if tried to power on. And then everything is black and cold as death.
I think it have been flashed with wrong ROM. Anybody here can guide me with the test points of Lg G Pro 2 (D838 F350) ? So that I can force it to QHSUSB_BULK ? Or any step by step advice to get it up ?
I am in real need of assistance, and thanks in advance for any sort of help. Best Regards.
I would like to mention that the phone indicator blinks for sometime if I try to power it on, as it does on boot, but nothing else is there. No recognition by PC, no presence in Device Manager. Blinks for sometime, stops, again starts blinking... and this goes on at regular short intervals. The area around the camera gets warm after sometime. Everything loops till I pull off battery.
Now, am I missing something ? Is the problem not as deadly as I am thinking ? Is it soft bricked ?
Hi, I not sure how it got bricked I never brick LG device.
Normally if anything happen we try pull battery out and put it back in, try then to turn the phone on.
Have you try connect to to pc with USB cable, one end of USB connnect to pc and other end connect to the phone. Then try press Power + Volume Up or Power + Volume down, this is to try to get into phone download mode. If you can get into download mode you can flash the kdz file to make it useable again.
Or without the USB cable we want to get to factory reset mode by use hardware method try press:
- Power + Volume Up or Power + Volume down
- If you see LG logo come up release the buttons you press above 1-2 second
- Press again Power + Volume Up or Power + Volume down
- Until it show and ask to use volume up/down button to select choice, say yes
Caution factory reset will delete all data on the phone and reset it as when you bought it new.
- Again it will ask for factory reset, use Volume up/down to choose and select yes for factory reset
turn on the phone and when light is blink press volume up or down button for some time and see if it it is detected as usbhulq?
Related
Quick explanation
Ok so i had the bootloop problem with my Infuse , i fixed it by opening my phone and playing with the power button hardware.
I accidently broke the power button , I looked for hours for a way to turn on my phone with out a power button with no success until i found tried this:
TUTORIAL STARTS HERE
1. Enter Download mode by holding both volume rockers and inserting a USB cable while still holding
2. Get to the screen that asks you if continue with Download Mode or not.
3. Remove USB cable and click the 2nd option.
4. Phone will restart and that's how you turn on a phone with no power button.
Hope it helped some people.
you can also try a re-map.
thread started by MrKickstand:
http://forum.xda-developers.com/showthread.php?t=1996709
you can also try to use the volume button parts to replace the power button...or order a new power button
my touch
vich32 said:
Quick explanation
Ok so i had the bootloop problem with my Infuse , i fixed it by opening my phone and playing with the power button hardware.
I accidently broke the power button , I looked for hours for a way to turn on my phone with out a power button with no success until i found tried this:
TUTORIAL STARTS HERE
1. Enter Download mode by holding both volume rockers and inserting a USB cable while still holding
2. Get to the screen that asks you if continue with Download Mode or not.
3. Remove USB cable and click the 2nd option.
4. Phone will restart and that's how you turn on a phone with no power button.
Hope it helped some people.
Click to expand...
Click to collapse
what about lg mytouch e-739
foundboy said:
what about lg mytouch e-739
Click to expand...
Click to collapse
I think only Samsung uses "Download Mode". LG probably has Fastboot like most other Android devices (Vol-Dn + Pwr). But you can try it - it won't hurt.
EDIT: Finally got an LG device. It does indeed have Download mode (and no Fastboot...Vol-Dn+Pwr brings me to a scaled back bootloader). Don't know if if asks to continue or not, but Download Mode doesn't hurt the phone unless you are potentially flashing software with it.
iTs working!! on Motorola Razr xt910
Android 2.2 and is working! After the phone turn on I was downloaded the app pwr bottom to volume key! And that is all okkk!
But take care after press (down and up) if you press up Inside tthe download mode this mean select! And on my first time I have take the recovery mode! xD
Good loooook!
vich32 said:
Quick explanation
Ok so i had the bootloop problem with my Infuse , i fixed it by opening my phone and playing with the power button hardware.
I accidently broke the power button , I looked for hours for a way to turn on my phone with out a power button with no success until i found tried this:
TUTORIAL STARTS HERE
1. Enter Download mode by holding both volume rockers and inserting a USB cable while still holding
2. Get to the screen that asks you if continue with Download Mode or not.
3. Remove USB cable and click the 2nd option.
4. Phone will restart and that's how you turn on a phone with no power button.
Hope it helped some people.
Click to expand...
Click to collapse
I have samsung galaxy y running android 2.3.6. will this work on it as my power button is not working.
tusharg said:
I have samsung galaxy y running android 2.3.6. will this work on it as my power button is not working.
Click to expand...
Click to collapse
Download Mode should work the same across all Samsung models. So, probably...
vich32 said:
Quick explanation
Ok so i had the bootloop problem with my Infuse , i fixed it by opening my phone and playing with the power button hardware.
I accidently broke the power button , I looked for hours for a way to turn on my phone with out a power button with no success until i found tried this:
TUTORIAL STARTS HERE
1. Enter Download mode by holding both volume rockers and inserting a USB cable while still holding
2. Get to the screen that asks you if continue with Download Mode or not.
3. Remove USB cable and click the 2nd option.
4. Phone will restart and that's how you turn on a phone with no power button.
Hope it helped some people.
Click to expand...
Click to collapse
Hello mate!!! Thanks for the post but i have problems here. First of all my phone (Galaxy Wonder) goes into download mode by pressing volume down + home btn + power button, so i though instead of the volume rockets i had to press volume down + power button and then usb cable. It worked. Got into download mode!!! Then i remove the cable, wait a few seconds and then press down to cancel and restart. Then it happens that the screen shows a grey battery, then it fades out and back in for twice. Then the phone just turns off. Battery is charged! What could be the problem? (I have to say i just completely removed the power button from the motherboard, but keeping the metal things that were around it still soldered on the motherboards.
Any guess???
Thanks a lot
LG mytouch e739
My mytouch just goes into s/w upgrade and stays there forever.
vich32 said:
Quick explanation
Ok so i had the bootloop problem with my Infuse , i fixed it by opening my phone and playing with the power button hardware.
I accidently broke the power button , I looked for hours for a way to turn on my phone with out a power button with no success until i found tried this:
TUTORIAL STARTS HERE
1. Enter Download mode by holding both volume rockers and inserting a USB cable while still holding
2. Get to the screen that asks you if continue with Download Mode or not.
3. Remove USB cable and click the 2nd option.
4. Phone will restart and that's how you turn on a phone with no power button.
Hope it helped some people.
Click to expand...
Click to collapse
Great... that helped.
I can't choose because my power button is off
Hi guys!
I have a problem...
I bought my lumia 1020 on dec/25... two days later i was using the GoPro app and my phone frezon.
I did a soft reset but then... it doesnt turn on any more.
I Tried all combinations seen in the internet about soft/hard reset, all buttons pressed but nothing. Plugged in pc... it doesnt even point somenthing in USB.
Today, I plugged in USB and noticed that the middle windows light was on for a period... tried again the buttons procedure but nothing...
I´m from brazil and a friend brought it to me from England so... I dont know if i sent it to Nokia will do...
Plz, does anybody knows what I can do?
Thx!
k1t4r0 said:
Hi guys!
I have a problem...
I bought my lumia 1020 on dec/25... two days later i was using the GoPro app and my phone frezon.
I did a soft reset but then... it doesnt turn on any more.
I Tried all combinations seen in the internet about soft/hard reset, all buttons pressed but nothing. Plugged in pc... it doesnt even point somenthing in USB.
Today, I plugged in USB and noticed that the middle windows light was on for a period... tried again the buttons procedure but nothing...
I´m from brazil and a friend brought it to me from England so... I dont know if i sent it to Nokia will do...
Plz, does anybody knows what I can do?
Thx!
Click to expand...
Click to collapse
All these descriptions assumes your phone is turned off. (hold down power to power off device)
Holding down volume down when you power up the device should boot into a recovery menu, if not,
Try holding Down [Volume Down] + [Power ] until The Phone vibrates (This may take a little while, keep holding)
If it vibrates but still doesn't work, hold down until you feel it vibrate twice. (this will factory reset the phone, so you'll lose everything)
One last thing you can try is hold down volume down, power on the device and connect the charger. Keep holding volume down until you see an exclamation mark. Then press the following combination of buttons:
Volume up, volume down, power, volume down. This will also factory reset the device.
(this point may void warranty if not careful)
If you feel brave, you could look into using ADB to connect and launch the recovery menu if all else fails, but it can get a bit technical, and my advice is that you should have some experience with adv or flashing or similar. Google and read guides for it and decide for yourself, but remember, its better to wait for a repair on warranty than trying to fix it yourself at the risk of voiding warranty. (also, you usually get 3months warranty on the repair.
Hope this helps
Changis said:
All these descriptions assumes your phone is turned off. (hold down power to power off device)
Holding down volume down when you power up the device should boot into a recovery menu, if not,
Try holding Down [Volume Down] + [Power ] until The Phone vibrates (This may take a little while, keep holding)
If it vibrates but still doesn't work, hold down until you feel it vibrate twice. (this will factory reset the phone, so you'll lose everything)
One last thing you can try is hold down volume down, power on the device and connect the charger. Keep holding volume down until you see an exclamation mark. Then press the following combination of buttons:
Volume up, volume down, power, volume down. This will also factory reset the device.
(this point may void warranty if not careful)
If you feel brave, you could look into using ADB to connect and launch the recovery menu if all else fails, but it can get a bit technical, and my advice is that you should have some experience with adv or flashing or similar. Google and read guides for it and decide for yourself, but remember, its better to wait for a repair on warranty than trying to fix it yourself at the risk of voiding warranty. (also, you usually get 3months warranty on the repair.
Hope this helps
Click to expand...
Click to collapse
Changis,
Hi and thx 4 the answear but the logic board was dead
Have to change it...
k1t4r0 said:
Changis,
Hi and thx 4 the answear but the logic board was dead
Have to change it...
Click to expand...
Click to collapse
Admins... could close the topic?
Thx
me too had the same issue
me too
i have the same issue with my lumia 1020
i connect it to change at night but on morning if found it dead "Not starting , Not charging" and also failed to force restart it
i bring it to my local nokia partner but they say that there is no replacement parts available for it so they refused to accept its maintenance
i don't know what i can do for it
So before, my power button gave me issues where it required substantial force to be used in order to get any response. Now all of a sudden, the fingerprint sensor went out as well as the power button itself. When attempting to do a hard reset to correct the problem, the phone won't turn on anymore. So it would seem that the power button no longer works and now I cannot turn on my phone . I've attempted to go into download mode or even the bootloader with little to no luck at all.
Does anyone have an alternative way to power on the phone so I can attempt to backup my data?
konoha457 said:
So before, my power button gave me issues where it required substantial force to be used in order to get any response. Now all of a sudden, the fingerprint sensor went out as well as the power button itself. When attempting to do a hard reset to correct the problem, the phone won't turn on anymore. So it would seem that the power button no longer works and now I cannot turn on my phone . I've attempted to go into download mode or even the bootloader with little to no luck at all.
Does anyone have an alternative way to power on the phone so I can attempt to backup my data?
Click to expand...
Click to collapse
This took a lot of trial and error with various button combinations, but I think I found a solution that works.
You must use the wall charger and cord. That's what I used.
1. Press and hold the volume up and down button at the same time.
2. Plug in the wall charger to the charging port.
3. You will see the lg logo on your phone.
4 Right when you see the lg logo unplug the charger from the phone.
5. Continue holding the volume up and down button.
6. LG logo will go away and then come back and your phone should boot.
5. Release the volume up and down button when it starts to boot.
Note: If you don't pull the power cord right when you see the lg logo, it will go into charging mode.
I was able to successfully boot my phone from a powered off state this way 3 times with no problem.
Once you get it booted, you could download an app from the play store to remap a volume button to be a power button as a temporary solution.
https://play.google.com/store/apps/details?id=com.teliapp.powervolume
Other options:
https://play.google.com/store/search?q=power button to volume button
I hope this helps.
duke69111 said:
This took a lot of trial and error with various button combinations, but I think I found a solution that works.
You must use the wall charger and cord. That's what I used.
1. Press and hold the volume up and down button at the same time.
2. Plug in the wall charger to the charging port.
3. You will see the lg logo on your phone.
4 Right when you see the lg logo unplug the charger from the phone.
5. Continue holding the volume up and down button.
6. LG logo will go away and then come back and your phone should boot.
5. Release the volume up and down button when it starts to boot.
Note: If you don't pull the power cord right when you see the lg logo, it will go into charging mode.
I was able to successfully boot my phone from a powered off state this way 3 times with no problem.
Once you get it booted, you could download an app from the play store to remap a volume button to be a power button as a temporary solution.
https://play.google.com/store/apps/details?id=com.teliapp.powervolume
Other options:
https://play.google.com/store/search?q=power button to volume button
I hope this helps.
Click to expand...
Click to collapse
Holy ****, this method works! Thank you so much, you just saved my bacon!
konoha457 said:
Holy ****, this method works! Thank you so much, you just saved my bacon!
Click to expand...
Click to collapse
You're welcome. Glad I could help.
fkin ****e it worked. thank you my dude
My Nexus 5 was drained off battery and was not taking charging suddenly. I entered the hard reset mode( power+volume down button) and accidently did a "restart bootloader". Since then my phone has been hard bricked! I cannot enter into recovery mode as well( power + volume down button). But I am sure that if I can get the bootloader running somehow, my phone will be back. I am sure it does not have any grave hardware issues as such. But the maintenance (service) center says , they will need to replace the motherboard, which is too costly for me.
Can anyone give me any pointers of how can I get my phone working again?
aman572 said:
My Nexus 5 was drained off battery and was not taking charging suddenly. I entered the hard reset mode( power+volume down button) and accidently did a "restart bootloader". Since then my phone has been hard bricked! I cannot enter into recovery mode as well( power + volume down button). But I am sure that if I can get the bootloader running somehow, my phone will be back. I am sure it does not have any grave hardware issues as such. But the maintenance (service) center says , they will need to replace the motherboard, which is too costly for me.
Can anyone give me any pointers of how can I get my phone working again?
Click to expand...
Click to collapse
Have you tried connecting it to a computer and seeing if it gets detected by the computer in device manager? If so, it should still be possible to bring it back.
What exactly happens when you try to power it on? Does the screen turn on at all? Does it vibrate once, as supposed to, when you press the power button? Or is it completely unresponsive? Also, when you plug it in to charge, does a red LED light up where the notification light normally is?
Also, try various combinations of powering up sequences. You want to try the following:
Hold power
Hold power + vol down (this should bring you into bootloader)
Hold power + vol up
Hold power + both volume buttons
Let me know what happens when you try this, and maybe I can help you out!
D2206. Got into a bootloop (the phone only shows the Sony and Xperia logo but ain't starting the system and just restarting forever doing it again and again). Can't get into Fastboot mode because volume buttons and power button isn't reacting at all. The only solution to force it to show some traces of life is plug him to PC or to a charging device but nothing happens except the charging lightning animation appears. And after connecting to PC, it seems like Flashtool recognize him, but nothing can be done because of the periodic 5-7 second interval disconnects.
Any solutions or tips?
You need to power off before connecting. Here's how.
I don't know if you figured this out or still need the help now, but I'm answering because it's the one thing here that I do know the answer to.
From your description, it sounds like you are trying to connect your phone to PC while the phone is still in boot loop. This will not work. You need to power it off first. Since your power and volume buttons won't respond during boot loop, you will need to use the hardware override that is provided.
Under the back panel of your phone, between the SIM2 and microSD slots, you will see a small punch-hole about 2 mm in diameter and labelled "OFF." Use a pen or precision screwdriver to gently press the off switch located inside this punch-hole for about 1 sec. Phone should switch off.
Wait about 15 sec before connecting to PC in Flash (Vol Up pressed down) or Fastboot (Vol Down pressed down) mode until the LED flashes the respective colour and then you can follow whatever instructions you are following.